Aluminum Electrolytic Capacitors/ UQ Snap-in Type Series: UQ Type: TS ■ Features ● Endurance : 85 °C 2000 h ● 30 % Smaller than series TS-UP ● RoHS directive compliant ■ Specifications Category Temp. Range Rated W.V. Range Nominal Cap. Range Capacitance Tolerance –40 °C to +85 °C 16 V.DC to 100 V.DC 160 V.DC to 250 V.DC 1000 µF to 100000 µF 270 µF to 3900 µF ±20 % (120 Hz/+20 °C) –25 °C to +85 °C 315 V.DC to 450 V.DC 82 µF to 1000 µF 3앀 CV (µA) max. After 5 minutes application of rated working voltage at +20 °C C : Capacitance (µF) V: W.V. (V.DC) DC Leakage Current tan δ Please see the attached standard Frequency (Hz) 50 Frequency Correction 16 V.DC to 100 V.DC /C.F. 0.93 Factor for Ripple Current 160 V.DC to 450 V.DC /C.F. 0.75 products 60 0.95 0.80 list. 100 0.99 0.95 120 1.00 1.00 500 1.05 1.20 1 k 1.08 1.25 10 k to 1.15 1.40 After 2000 hours application of DC voltage with specified ripple current (< rated DC working voltage) at +85 °C±2 °C, the capacitors shall meet the following limits. Capacitance change < ±20 % of initial measured value tan δ < 200 % of initial specified value DC leakage current < initial specified value Endurance After storage for 1000 hours at +85 °C±2 °C within no voltage applied and then being stabilized at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment) Shelf Life ■ Dimensions in mm (not to scale) φD+1.0 max. Polarity bar (mm) (1 0 .0 Sleeve 2-φ2.0±0.1 10 .0± 0.1 ) Vent L+2.0 max. (φD) 4.0±0.5 Rated voltage etc. indicate to sleeve. Recommended PWB piercing plan 4.0±0.5 +0.2 2.0 max. Terminal (t=0.8) (3.5) 0.8 –0.1 1.5±0.2 Top of spin Standard terminal type does not require terminal trimming process. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 12000 15000 18000 22000 27000 33000 16 39000 47000 56000 68000 ✽ ✽ 82000 100000 8200 10000 12000 15000 18000 22000 25 27000 33000 39000 47000 ✽ ✽ 56000 68000 Dia. Length (mm) 22 22 22 25 22 25 22 25 30 22 25 30 35 25 30 25 30 35 30 35 30 35 35 35 22 22 22 25 22 25 22 25 30 22 25 30 35 25 30 25 30 35 30 35 30 35 35 35 (mm) 25 30 35 25 40 30 45 35 25 50 40 30 25 45 35 50 40 30 45 35 50 40 45 50 25 30 30 25 35 30 40 35 25 45 40 30 25 45 35 50 40 30 45 35 50 40 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETUQ1C123HJ EETUQ1C153HJ EETUQ1C183HJ EETUQ1C183JJ EETUQ1C223HJ EETUQ1C223JJ EETUQ1C273HJ EETUQ1C273JJ EETUQ1C273KJ EETUQ1C333HJ EETUQ1C333JJ EETUQ1C333KJ EETUQ1C333LJ EETUQ1C393JJ EETUQ1C393KJ EETUQ1C473JJ EETUQ1C473KJ EETUQ1C473LJ EETUQ1C563KJ EETUQ1C563LJ EETUQ1C683KJ EETUQ1C683LJ EETUQ1C823LJ EETUQ1C104LJ EETUQ1E822HJ EETUQ1E103HJ EETUQ1E123HJ EETUQ1E123JJ EETUQ1E153HJ EETUQ1E153JJ EETUQ1E183HJ EETUQ1E183JJ EETUQ1E183KJ EETUQ1E223HJ EETUQ1E223JJ EETUQ1E223KJ EETUQ1E223LJ EETUQ1E273JJ EETUQ1E273KJ EETUQ1E333JJ EETUQ1E333KJ EETUQ1E333LJ EETUQ1E393KJ EETUQ1E393LJ EETUQ1E473KJ EETUQ1E473LJ EETUQ1E563LJ EETUQ1E683LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) 4.5 0.50 5.3 0.50 5.6 0.50 5.6 0.50 6.1 0.50 6.1 0.50 6.3 0.50 6.3 0.50 6.3 0.50 6.8 0.50 6.8 0.50 6.8 0.50 6.8 0.50 6.9 0.56 6.9 0.56 7.5 0.64 7.5 0.64 7.5 0.64 8.7 0.73 8.7 0.73 9.1 0.85 9.1 0.85 9.5 0.99 10.2 1.17 3.6 0.40 3.8 0.40 4.1 0.40 4.1 0.40 4.6 0.40 4.6 0.40 5.5 0.40 5.5 0.40 5.5 0.40 6.1 0.40 6.1 0.40 6.1 0.40 6.1 0.40 6.2 0.40 6.2 0.40 6.8 0.40 6.8 0.40 6.8 0.40 7.4 0.46 7.4 0.46 8.0 0.54 8.0 0.54 8.7 0.63 9.6 0.75 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 200 100 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 200 100 100 100 100 100 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) (mm) 5600 6800 22 22 22 25 22 25 22 25 30 22 25 25 30 35 25 30 35 30 35 30 35 35 35 22 22 22 25 22 22 25 30 22 25 22 25 30 35 25 30 35 30 35 30 35 35 35 25 30 30 25 35 30 40 35 25 45 40 45 30 25 50 35 30 45 35 50 40 45 50 25 30 30 25 35 40 30 25 45 35 50 40 30 25 45 35 30 40 35 45 40 45 50 8200 10000 12000 15000 35 18000 22000 27000 33000 ✽ ✽ 39000 47000 3300 3900 4700 5600 6800 8200 50 10000 12000 15000 18000 ✽ ✽ 22000 27000 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETUQ1V562HJ EETUQ1V682HJ EETUQ1V822HJ EETUQ1V822JJ EETUQ1V103HJ EETUQ1V103JJ EETUQ1V123HJ EETUQ1V123JJ EETUQ1V123KJ EETUQ1V153HJ EETUQ1V153JJ EETUQ1V183JJ EETUQ1V183KJ EETUQ1V183LJ EETUQ1V223JJ EETUQ1V223KJ EETUQ1V223LJ EETUQ1V273KJ EETUQ1V273LJ EETUQ1V333KJ EETUQ1V333LJ EETUQ1V393LJ EETUQ1V473LJ EETUQ1H332HJ EETUQ1H392HJ EETUQ1H472HJ EETUQ1H472JJ EETUQ1H562HJ EETUQ1H682HJ EETUQ1H682JJ EETUQ1H682KJ EETUQ1H822HJ EETUQ1H822JJ EETUQ1H103HJ EETUQ1H103JJ EETUQ1H103KJ EETUQ1H103LJ EETUQ1H123JJ EETUQ1H123KJ EETUQ1H123LJ EETUQ1H153KJ EETUQ1H153LJ EETUQ1H183KJ EETUQ1H183LJ EETUQ1H223LJ EETUQ1H273LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) 3.4 3.7 4.0 4.0 4.4 4.4 5.1 5.1 5.1 5.6 5.6 5.7 5.7 5.7 6.1 6.1 6.1 6.8 6.8 7.2 7.2 7.7 8.5 2.7 2.8 3.0 3.0 3.4 3.9 3.9 3.9 4.4 4.4 5.0 5.0 5.0 5.0 5.6 5.6 5.6 6.4 6.4 6.9 6.9 7.6 8.3 Min. Packaging Q'ty 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.41 0.49 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) (mm) 2200 2700 22 22 22 25 22 25 22 25 30 22 25 25 30 35 25 30 35 30 35 30 35 35 35 22 22 22 25 22 25 22 25 30 22 25 25 30 25 30 35 30 35 30 35 35 35 25 30 30 25 35 30 40 35 25 45 40 45 30 25 50 35 30 40 35 45 40 45 50 25 30 35 25 40 30 45 35 25 50 40 45 30 50 35 30 45 35 50 40 45 50 3300 3900 4700 5600 63 6800 8200 10000 12000 ✽ ✽ 15000 18000 1500 1800 2200 2700 3300 3900 80 4700 5600 6800 8200 ✽ ✽ 10000 12000 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETUQ1J222HJ EETUQ1J272HJ EETUQ1J332HJ EETUQ1J332JJ EETUQ1J392HJ EETUQ1J392JJ EETUQ1J472HJ EETUQ1J472JJ EETUQ1J472KJ EETUQ1J562HJ EETUQ1J562JJ EETUQ1J682JJ EETUQ1J682KJ EETUQ1J682LJ EETUQ1J822JJ EETUQ1J822KJ EETUQ1J822LJ EETUQ1J103KJ EETUQ1J103LJ EETUQ1J123KJ EETUQ1J123LJ EETUQ1J153LJ EETUQ1J183LJ EETUQ1K152HJ EETUQ1K182HJ EETUQ1K222HJ EETUQ1K222JJ EETUQ1K272HJ EETUQ1K272JJ EETUQ1K332HJ EETUQ1K332JJ EETUQ1K332KJ EETUQ1K392HJ EETUQ1K392JJ EETUQ1K472JJ EETUQ1K472KJ EETUQ1K562JJ EETUQ1K562KJ EETUQ1K562LJ EETUQ1K682KJ EETUQ1K682LJ EETUQ1K822KJ EETUQ1K822LJ EETUQ1K103LJ EETUQ1K123LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) 2.5 3.7 4.1 4.1 4.4 4.4 4.9 4.9 4.9 5.4 5.4 5.8 5.8 6.0 6.0 6.0 6.5 6.5 6.5 7.2 7.2 7.9 8.6 2.3 2.5 2.7 2.7 2.8 2.8 3.2 3.2 3.2 3.6 3.6 4.1 4.1 4.6 4.6 4.6 5.2 5.2 5.8 5.8 6.4 7.0 Min. Packaging Q'ty 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.30 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) (mm) 1000 1200 1500 1800 2200 2700 100 3300 3900 4700 5600 ✽ ✽ 6800 8200 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) Min. Packaging Q'ty (pcs) 22 25 EETUQ2A102HJ 2.0 0.25 200 22 30 EETUQ2A122HJ 2.3 0.25 200 25 25 EETUQ2A122JJ 2.3 0.25 200 22 30 EETUQ2A152HJ 2.6 0.25 200 22 35 EETUQ2A182HJ 2.8 0.25 200 25 30 EETUQ2A182JJ 2.8 0.25 200 22 45 EETUQ2A222HJ 3.1 0.25 200 25 35 EETUQ2A222JJ 3.1 0.25 200 30 25 EETUQ2A222KJ 3.1 0.25 200 22 50 EETUQ2A272HJ 3.7 0.25 200 25 40 EETUQ2A272JJ 3.7 0.25 200 30 30 EETUQ2A272KJ 3.7 0.25 200 35 25 EETUQ2A272LJ 3.7 0.25 200 25 45 EETUQ2A332JJ 4.1 0.25 200 30 35 EETUQ2A332KJ 4.1 0.25 100 25 50 EETUQ2A392JJ 4.5 0.25 200 30 40 EETUQ2A392KJ 4.5 0.25 100 35 30 EETUQ2A392LJ 4.5 0.25 200 30 45 EETUQ2A472KJ 5.1 0.25 100 35 35 EETUQ2A472LJ 5.1 0.25 100 30 50 EETUQ2A562KJ 5.8 0.25 100 35 40 EETUQ2A562LJ 5.8 0.25 100 35 35 45 50 EETUQ2A682LJ EETUQ2A822LJ 6.6 7.2 0.25 0.25 100 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) (mm) 560 680 820 22 22 22 22 25 22 25 30 22 25 30 35 25 30 35 30 35 30 35 35 35 22 22 22 25 22 25 22 25 30 22 25 30 35 25 30 35 25 30 35 30 35 30 35 35 25 30 35 40 30 45 35 25 50 40 30 25 45 35 30 40 35 45 40 45 50 25 30 30 25 35 30 45 35 25 50 40 30 25 45 35 30 50 40 30 45 40 50 45 50 1000 1200 1500 160 1800 2200 2700 ✽ ✽ 3300 3900 470 560 680 820 1000 1200 180 1500 1800 2200 ✽ ✽ 2700 3300 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETUQ2C561HJ EETUQ2C681HJ EETUQ2C821HJ EETUQ2C102HJ EETUQ2C102JJ EETUQ2C122HJ EETUQ2C122JJ EETUQ2C122KJ EETUQ2C152HJ EETUQ2C152JJ EETUQ2C152KJ EETUQ2C152LJ EETUQ2C182JJ EETUQ2C182KJ EETUQ2C182LJ EETUQ2C222KJ EETUQ2C222LJ EETUQ2C272KJ EETUQ2C272LJ EETUQ2C332LJ EETUQ2C392LJ EETUQ2P471HJ EETUQ2P561HJ EETUQ2P681HJ EETUQ2P681JJ EETUQ2P821HJ EETUQ2P821JJ EETUQ2P102HJ EETUQ2P102JJ EETUQ2P102KJ EETUQ2P122HJ EETUQ2P122JJ EETUQ2P122KJ EETUQ2P122LJ EETUQ2P152JJ EETUQ2P152KJ EETUQ2P152LJ EETUQ2P182JJ EETUQ2P182KJ EETUQ2P182LJ EETUQ2P222KJ EETUQ2P222LJ EETUQ2P272KJ EETUQ2P272LJ EETUQ2P332LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) 2.25 2.50 2.75 3.00 3.00 3.25 3.25 3.25 3.73 3.73 3.73 3.73 4.20 4.20 4.20 4.78 4.78 5.45 5.45 5.75 6.00 2.08 2.25 2.50 2.50 2.75 2.75 3.00 3.00 3.00 3.31 3.31 3.31 3.31 3.83 3.83 3.83 4.32 4.32 4.32 4.92 4.92 5.52 5.52 5.75 Min. Packaging Q'ty 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 200 100 200 100 100 100 100 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) (mm) 390 470 22 22 22 25 22 25 22 25 30 22 25 30 35 22 25 30 25 30 35 30 35 30 35 35 22 22 25 22 25 22 22 25 30 22 25 25 30 25 30 35 30 35 30 35 35 25 30 30 25 35 30 40 30 25 45 35 30 25 50 40 30 50 35 30 45 35 50 40 50 25 30 25 35 30 35 40 30 25 45 35 45 30 50 35 30 45 35 50 40 50 560 680 820 1000 200 1200 1500 1800 2200 ✽ 2700 330 470 560 680 820 220 1000 1200 1500 1800 ✽ 2200 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETUQ2D391HJ EETUQ2D471HJ EETUQ2D561HJ EETUQ2D561JJ EETUQ2D681HJ EETUQ2D681JJ EETUQ2D821HJ EETUQ2D821JJ EETUQ2D821KJ EETUQ2D102HJ EETUQ2D102JJ EETUQ2D102KJ EETUQ2D102LJ EETUQ2D122HJ EETUQ2D122JJ EETUQ2D122KJ EETUQ2D152JJ EETUQ2D152KJ EETUQ2D152LJ EETUQ2D182KJ EETUQ2D182LJ EETUQ2D222KJ EETUQ2D222LJ EETUQ2D272LJ EETUQ2Q331HJ EETUQ2Q471HJ EETUQ2Q471JJ EETUQ2Q561HJ EETUQ2Q561JJ EETUQ2Q681HC EETUQ2Q681HJ EETUQ2Q681JJ EETUQ2Q681KJ EETUQ2Q821HJ EETUQ2Q821JJ EETUQ2Q102JJ EETUQ2Q102KJ EETUQ2Q122JJ EETUQ2Q122KJ EETUQ2Q122LJ EETUQ2Q152KJ EETUQ2Q152LJ EETUQ2Q182KJ EETUQ2Q182LJ EETUQ2Q222LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) 1.68 1.85 2.43 2.43 2.68 2.68 2.93 2.93 2.93 3.25 3.25 3.25 3.25 3.50 3.50 3.50 3.87 3.87 3.87 4.32 4.32 4.92 4.92 5.45 1.58 1.99 1.99 2.28 2.28 2.46 2.46 2.46 2.46 2.81 2.81 3.29 3.29 3.60 3.60 3.60 3.92 3.92 4.30 4.30 4.95 Min. Packaging Q'ty 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 270 330 390 470 560 680 250 820 1000 1200 1500 ✽ 1800 2200 180 220 270 330 390 315 470 560 680 820 ✽ 1000 Dia. Length (mm) 22 22 22 25 22 25 22 25 30 22 25 30 22 25 30 35 25 30 35 30 35 30 35 35 35 22 22 22 22 25 30 22 25 30 22 25 30 35 25 30 35 30 35 30 35 30 35 (mm) 25 30 30 25 35 30 40 30 25 45 35 30 50 40 30 25 45 35 30 40 35 50 40 45 50 25 30 30 40 30 25 45 35 30 50 40 30 25 45 35 30 40 35 45 40 50 45 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETUQ2E271HJ EETUQ2E331HJ EETUQ2E391HJ EETUQ2E391JJ EETUQ2E471HJ EETUQ2E471JJ EETUQ2E561HJ EETUQ2E561JJ EETUQ2E561KJ EETUQ2E681HJ EETUQ2E681JJ EETUQ2E681KJ EETUQ2E821HJ EETUQ2E821JJ EETUQ2E821KJ EETUQ2E821LJ EETUQ2E102JJ EETUQ2E102KJ EETUQ2E102LJ EETUQ2E122KJ EETUQ2E122LJ EETUQ2E152KJ EETUQ2E152LJ EETUQ2E182LJ EETUQ2E222LJ EETUQ2F181HJ EETUQ2F221HJ EETUQ2F271HJ EETUQ2F331HJ EETUQ2F331JJ EETUQ2F331KJ EETUQ2F391HJ EETUQ2F391JJ EETUQ2F391KJ EETUQ2F471HJ EETUQ2F471JJ EETUQ2F471KJ EETUQ2F471LJ EETUQ2F561JJ EETUQ2F561KJ EETUQ2F561LJ EETUQ2F681KJ EETUQ2F681LJ EETUQ2F821KJ EETUQ2F821LJ EETUQ2F102KJ EETUQ2F102LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) 1.31 0.15 1.75 0.15 1.91 0.15 1.91 0.15 2.11 0.15 2.11 0.15 2.25 0.15 2.25 0.15 2.25 0.15 2.50 0.15 2.50 0.15 2.50 0.15 2.77 0.15 2.77 0.15 2.77 0.15 2.77 0.15 3.32 0.15 3.32 0.15 3.32 0.15 3.53 0.15 3.53 0.15 4.04 0.15 4.04 0.15 4.55 0.15 4.75 0.15 1.21 0.15 1.41 0.15 1.60 0.15 1.82 0.15 1.82 0.15 1.82 0.15 2.01 0.15 2.01 0.15 2.01 0.15 2.27 0.15 2.27 0.15 2.27 0.15 2.27 0.15 2.56 0.15 2.56 0.15 2.56 0.15 2.87 0.15 2.87 0.15 3.25 0.15 3.25 0.15 3.63 0.15 3.63 0.15 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 150 180 220 270 330 390 350 470 560 680 820 ✽ ✽ 1000 120 150 180 220 270 330 400 390 470 560 680 ✽ ✽ ✽ 820 Dia. Length (mm) 22 22 22 22 25 22 25 22 25 30 35 25 30 35 25 30 35 30 35 30 35 35 22 22 22 22 22 22 25 22 25 30 30 22 25 30 35 25 30 35 25 30 35 30 35 30 35 35 35 35 (mm) 25 30 35 40 30 45 35 50 40 30 25 45 35 30 50 40 30 45 35 50 45 50 25 30 30 35 35 40 30 45 35 25 30 50 40 30 25 45 35 30 50 40 30 45 35 50 40 45 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETUQ2V151HJ EETUQ2V181HJ EETUQ2V221HJ EETUQ2V271HJ EETUQ2V271JJ EETUQ2V331HJ EETUQ2V331JJ EETUQ2V391HJ EETUQ2V391JJ EETUQ2V391KJ EETUQ2V391LJ EETUQ2V471JJ EETUQ2V471KJ EETUQ2V471LJ EETUQ2V561JJ EETUQ2V561KJ EETUQ2V561LJ EETUQ2V681KJ EETUQ2V681LJ EETUQ2V821KJ EETUQ2V821LJ EETUQ2V102LJ EETUQ2G121HJ EETUQ2G151HJ EETUQ2G181HC EETUQ2G181HJ EETUQ2G221HC EETUQ2G221HJ EETUQ2G221JJ EETUQ2G271HJ EETUQ2G271JJ EETUQ2G271KC EETUQ2G271KJ EETUQ2G331HJ EETUQ2G331JJ EETUQ2G331KJ EETUQ2G331LJ EETUQ2G391JJ EETUQ2G391KJ EETUQ2G391LJ EETUQ2G471JJ EETUQ2G471KJ EETUQ2G471LJ EETUQ2G561KJ EETUQ2G561LJ EETUQ2G681KJ EETUQ2G681LC EETUQ2G681LJ EETUQ2G821LC EETUQ2G821LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) 1.12 0.15 1.22 0.15 1.44 0.15 1.66 0.15 1.66 0.15 1.88 0.15 1.88 0.15 2.06 0.15 2.06 0.15 2.06 0.15 2.06 0.15 2.40 0.15 2.40 0.15 2.40 0.15 2.60 0.15 2.60 0.15 2.60 0.15 2.96 0.15 2.96 0.15 3.25 0.15 3.25 0.15 3.54 0.15 1.02 0.15 1.16 0.15 1.44 0.15 1.44 0.15 1.49 0.15 1.49 0.15 1.49 0.15 1.67 0.15 1.67 0.15 1.67 0.15 1.67 0.15 1.90 0.15 1.90 0.15 1.90 0.15 1.90 0.15 2.13 0.15 2.13 0.15 2.13 0.15 2.39 0.15 2.39 0.15 2.39 0.15 2.69 0.15 2.69 0.15 2.96 0.15 2.96 0.15 2.96 0.15 3.25 0.15 3.25 0.15 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 100 200 200 100 200 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 200 100 200 100 100 100 100 100 100 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) (mm) 120 150 180 220 270 420 330 390 470 560 ✽ ✽ 680 820 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) Min. Packaging Q'ty (pcs) 22 25 EETUQ2S121HJ 1.08 0.15 200 22 30 EETUQ2S151HJ 1.30 0.15 200 25 25 EETUQ2S151JJ 1.30 0.15 200 22 35 EETUQ2S181HJ 1.48 0.15 200 25 30 EETUQ2S181JJ 1.48 0.15 200 22 40 EETUQ2S221HJ 1.65 0.15 200 25 35 EETUQ2S221JJ 1.65 0.15 200 30 25 EETUQ2S221KJ 1.65 0.15 200 22 45 EETUQ2S271HJ 1.94 0.15 200 25 35 EETUQ2S271JC 1.94 0.15 200 25 40 EETUQ2S271JJ 1.94 0.15 200 30 30 EETUQ2S271KJ 1.94 0.15 200 25 45 EETUQ2S331JJ 2.17 0.15 200 30 30 EETUQ2S331KJ 2.17 0.15 200 35 25 EETUQ2S331LJ 2.17 0.15 200 25 50 EETUQ2S391JJ 2.27 0.15 200 30 35 EETUQ2S391KJ 2.27 0.15 100 35 30 EETUQ2S391LJ 2.27 0.15 200 30 40 EETUQ2S471KJ 2.61 0.15 100 35 35 EETUQ2S471LJ 2.61 0.15 100 30 45 EETUQ2S561KJ 2.82 0.15 100 35 40 EETUQ2S561LJ 2.82 0.15 100 30 50 EETUQ2S681KC 3.11 0.15 100 35 45 EETUQ2S681LJ 3.11 0.15 100 35 50 EETUQ2S821LJ 3.30 0.15 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ UQ ■ Standard Products Case size Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+85 °C) max. (A r.m.s.) Min. Packaging Q'ty W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) (mm) 82 22 25 EETUQ2W820HJ 0.83 0.15 200 100 22 25 EETUQ2W101HJ 0.93 0.15 200 120 150 180 220 450 270 330 390 470 ✽ 560 ✽ 680 (pcs) 22 30 EETUQ2W121HJ 1.04 0.15 200 22 30 EETUQ2W151HC 1.19 0.15 200 22 35 EETUQ2W151HJ 1.19 0.15 200 25 25 EETUQ2W151JC 1.19 0.15 200 25 30 EETUQ2W151JJ 1.19 0.15 200 22 35 EETUQ2W181HC 1.35 0.15 200 22 40 EETUQ2W181HJ 1.35 0.15 200 25 30 EETUQ2W181JJ 1.35 0.15 200 22 45 EETUQ2W221HJ 1.55 0.15 200 25 35 EETUQ2W221JC 1.55 0.15 200 25 40 EETUQ2W221JJ 1.55 0.15 200 30 25 EETUQ2W221KC 1.55 0.15 200 30 30 EETUQ2W221KJ 1.55 0.15 200 35 25 EETUQ2W221LJ 1.55 0.15 200 22 50 EETUQ2W271HJ 1.78 0.15 200 25 40 EETUQ2W271JJ 1.78 0.15 200 30 30 EETUQ2W271KJ 1.78 0.15 200 35 25 EETUQ2W271LC 1.78 0.15 200 25 45 EETUQ2W331JC 2.01 0.15 200 25 50 EETUQ2W331JJ 2.01 0.15 200 30 35 EETUQ2W331KC 2.01 0.15 100 30 40 EETUQ2W331KJ 2.01 0.15 100 35 30 EETUQ2W331LJ 2.01 0.15 200 30 40 EETUQ2W391KJ 2.24 0.15 100 35 30 EETUQ2W391LC 2.24 0.15 200 35 35 EETUQ2W391LJ 2.24 0.15 100 30 45 EETUQ2W471KJ 2.53 0.15 100 35 35 EETUQ2W471LC 2.53 0.15 100 35 40 EETUQ2W471LJ 2.53 0.15 100 30 50 EETUQ2W561KJ 2.82 0.15 100 35 40 EETUQ2W561LC 2.82 0.15 100 35 45 EETUQ2W561LJ 2.82 0.15 100 35 45 EETUQ2W681LC 3.00 0.15 100 Endurance : 85 °C 2000 h, Terminal Pitch : 10 mm ✽ When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jan. 2008