Aluminum Electrolytic Capacitors/ HC Snap-in Type Series: HC Type: TS ■ Features ● Endurance : 105 °C 2000 h ● 30 % smaller than series TS-HB ● RoHS directive compliant ■ Specifications Category Temp. Range Rated W.V. Range Nominal Cap. Range Capacitance Tolerance –40 °C to +105 °C 10 V.DC to 100 V.DC 160 V.DC to 250 V.DC 820 µF to 100000 µF 150 µF to 3300 µF ±20 % (120 Hz/+20 °C) –25 °C to +105 °C 315 V.DC to 450 V.DC 39 µF to 1000 µF 3앀 CV (µA) max. After 5 minutes application of rated working voltage at +20 °C. C : Capacitance (µF) V: W.V. (V.DC) DC Leakage Current tan δ Please see the attached standard Frequency (Hz) 50 Frequency Correction 10 V.DC to 100 V.DC /C.F. 0.93 Factor for Ripple Current 160 V.DC to 450 V.DC /C.F. 0.75 products 60 0.95 0.80 list 100 0.99 0.95 120 1.00 1.00 500 1.05 1.20 1 k 1.08 1.25 10 k to 1.15 1.40 After 2000 hours application of DC voltage with specified ripple current (< rated DC working voltage) at +105 °C±2 °C, the capacitors shall meet the following limits. Capacitance change < ±20 % of initial measured value tan δ < 200 % of initial specified value DC leakage current < initial specified value Endurance After storage for 1000 hours at +105 °C±2 °C within no voltage applied and then being stabilized at +20 °C, capacitors shall meet the limits specified in Endurance. (With voltage treatment) Shelf Life ■ Dimensions in mm (not to scale) φD+1.0 max. Polarity bar (mm) (1 0 .0 Sleeve 2-φ2.0±0.1 10 .0± 0.1 ) Vent L+2.0 max. (φD) 4.0±0.5 Rated voltage etc. indicate to sleeve. Recommended PWB piercing plan 4.0±0.5 +0.2 2.0 max. Terminal (t=0.8) (3.5) 0.8 –0.1 1.5±0.2 Top of spin Standard terminal type does not require terminal trimming peocess. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 12000 15000 18000 22000 27000 33000 10 39000 47000 56000 68000 ✽ ✽ 82000 100000 10000 12000 15000 18000 22000 16 27000 33000 39000 47000 56000 ✽ 68000 Dia. Length (mm) 22 22 22 25 22 25 22 25 30 22 25 25 30 35 25 30 35 30 35 30 35 35 35 22 22 25 22 22 25 22 25 30 22 25 30 35 25 30 30 35 30 35 30 35 35 (mm) 25 30 30 25 35 30 40 35 25 45 40 45 30 25 50 35 30 40 35 45 40 45 50 25 30 25 35 40 30 45 35 25 50 40 30 25 45 35 40 30 45 35 50 40 45 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC1A123HJ EETHC1A153HJ EETHC1A183HJ EETHC1A183JJ EETHC1A223HJ EETHC1A223JJ EETHC1A273HJ EETHC1A273JJ EETHC1A273KJ EETHC1A333HJ EETHC1A333JJ EETHC1A393JJ EETHC1A393KJ EETHC1A393LJ EETHC1A473JJ EETHC1A473KJ EETHC1A473LJ EETHC1A563KJ EETHC1A563LJ EETHC1A683KJ EETHC1A683LJ EETHC1A823LJ EETHC1A104LJ EETHC1C103HJ EETHC1C123HJ EETHC1C123JJ EETHC1C153HJ EETHC1C183HJ EETHC1C183JJ EETHC1C223HJ EETHC1C223JJ EETHC1C223KJ EETHC1C273HJ EETHC1C273JJ EETHC1C273KJ EETHC1C273LJ EETHC1C333JJ EETHC1C333KJ EETHC1C393KJ EETHC1C393LJ EETHC1C473KJ EETHC1C473LJ EETHC1C563KJ EETHC1C563LJ EETHC1C683LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 2.20 0.65 2.30 0.65 2.40 0.65 2.40 0.65 2.60 0.65 2.60 0.65 3.10 0.65 3.10 0.65 3.10 0.65 3.40 0.65 3.40 0.65 3.70 0.71 3.70 0.71 3.70 0.71 4.20 0.79 4.20 0.79 4.20 0.79 5.00 0.88 5.00 0.88 5.40 1.00 5.40 1.00 5.90 1.14 6.50 1.32 2.60 0.55 2.90 0.55 2.90 0.55 3.20 0.55 3.50 0.55 3.50 0.55 3.80 0.55 3.80 0.55 3.80 0.55 4.20 0.55 4.20 0.55 4.20 0.55 4.20 0.55 4.70 0.55 4.70 0.55 5.10 0.61 5.10 0.61 5.50 0.69 5.50 0.69 6.00 0.78 6.00 0.78 6.40 0.90 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 100 200 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 6800 8200 10000 12000 15000 18000 25 22000 27000 33000 ✽ ✽ 39000 47000 4700 5600 6800 8200 10000 12000 35 15000 18000 22000 ✽ ✽ 27000 33000 Dia. Length (mm) 22 22 25 22 22 25 22 25 30 22 25 30 35 25 30 35 30 35 30 35 30 35 35 22 22 25 22 22 25 22 25 30 22 25 30 35 25 30 35 30 35 30 35 30 35 35 (mm) 25 30 25 35 40 30 45 35 25 50 40 30 25 45 35 30 40 35 45 40 50 45 50 25 30 25 35 40 30 45 35 25 50 40 30 25 45 35 30 40 35 45 40 50 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC1E682HJ EETHC1E822HJ EETHC1E822JJ EETHC1E103HJ EETHC1E123HJ EETHC1E123JJ EETHC1E153HJ EETHC1E153JJ EETHC1E153KJ EETHC1E183HJ EETHC1E183JJ EETHC1E183KJ EETHC1E183LJ EETHC1E223JJ EETHC1E223KJ EETHC1E223LJ EETHC1E273KJ EETHC1E273LJ EETHC1E333KJ EETHC1E333LJ EETHC1E393KJ EETHC1E393LJ EETHC1E473LJ EETHC1V472HJ EETHC1V562HJ EETHC1V562JJ EETHC1V682HJ EETHC1V822HJ EETHC1V822JJ EETHC1V103HJ EETHC1V103JJ EETHC1V103KJ EETHC1V123HJ EETHC1V123JJ EETHC1V123KJ EETHC1V123LJ EETHC1V153JJ EETHC1V153KJ EETHC1V153LJ EETHC1V183KJ EETHC1V183LJ EETHC1V223KJ EETHC1V223LJ EETHC1V273KJ EETHC1V273LJ EETHC1V333LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 2.40 0.40 2.70 0.40 2.70 0.40 3.00 0.40 3.20 0.40 3.20 0.40 3.60 0.40 3.60 0.40 3.60 0.40 3.90 0.40 3.90 0.40 3.90 0.40 3.90 0.40 4.30 0.40 4.30 0.40 4.30 0.40 4.80 0.40 4.80 0.40 5.50 0.40 5.50 0.40 5.80 0.46 5.80 0.46 6.30 0.54 2.20 0.35 2.40 0.35 2.40 0.35 2.60 0.35 2.90 0.35 2.90 0.35 3.20 0.35 3.20 0.35 3.20 0.35 3.50 0.35 3.50 0.35 3.50 0.35 3.50 0.35 3.90 0.35 3.90 0.35 3.90 0.35 4.30 0.35 4.30 0.35 5.00 0.35 5.00 0.35 5.30 0.35 5.30 0.35 5.90 0.35 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 2700 3300 3900 4700 5600 6800 50 8200 10000 12000 15000 ✽ 18000 2200 2700 3300 3900 4700 5600 63 6800 8200 10000 ✽ ✽ 12000 15000 Dia. Length (mm) 22 22 22 25 22 25 22 25 30 22 25 30 35 25 30 25 30 35 30 35 30 35 35 22 22 25 22 22 25 30 22 25 22 25 30 35 25 30 35 30 35 30 35 30 35 35 (mm) 25 30 35 25 40 30 45 35 25 50 40 30 25 45 35 50 40 30 45 35 50 40 45 25 30 25 35 40 30 25 45 35 50 40 30 25 45 35 30 40 35 45 40 50 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC1H272HJ EETHC1H332HJ EETHC1H392HJ EETHC1H392JJ EETHC1H472HJ EETHC1H472JJ EETHC1H562HJ EETHC1H562JJ EETHC1H562KJ EETHC1H682HJ EETHC1H682JJ EETHC1H682KJ EETHC1H682LJ EETHC1H822JJ EETHC1H822KJ EETHC1H103JJ EETHC1H103KJ EETHC1H103LJ EETHC1H123KJ EETHC1H123LJ EETHC1H153KJ EETHC1H153LJ EETHC1H183LJ EETHC1J222HJ EETHC1J272HJ EETHC1J272JJ EETHC1J332HJ EETHC1J392HJ EETHC1J392JJ EETHC1J392KJ EETHC1J472HJ EETHC1J472JJ EETHC1J562HJ EETHC1J562JJ EETHC1J562KJ EETHC1J562LJ EETHC1J682JJ EETHC1J682KJ EETHC1J682LJ EETHC1J822KJ EETHC1J822LJ EETHC1J103KJ EETHC1J103LJ EETHC1J123KJ EETHC1J123LJ EETHC1J153LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 1.80 0.35 2.00 0.35 2.20 0.35 2.20 0.35 2.50 0.35 2.50 0.35 2.80 0.35 2.80 0.35 2.80 0.35 3.30 0.35 3.30 0.35 3.30 0.35 3.30 0.35 3.60 0.35 3.60 0.35 4.00 0.35 4.00 0.35 4.00 0.35 4.50 0.35 4.50 0.35 4.80 0.35 4.80 0.35 5.20 0.35 2.00 0.30 2.20 0.30 2.20 0.30 2.50 0.30 2.70 0.30 2.70 0.30 2.70 0.30 3.00 0.30 3.00 0.30 3.30 0.30 3.30 0.30 3.30 0.30 3.30 0.30 3.60 0.30 3.60 0.30 3.60 0.30 3.90 0.30 3.90 0.30 4.40 0.30 4.40 0.30 4.80 0.30 4.80 0.30 5.40 0.30 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 200 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 100 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 1200 1500 1800 2200 2700 3300 80 3900 4700 5600 6800 ✽ 8200 820 1000 1200 1500 1800 2200 100 2700 3300 3900 4700 ✽ ✽ 5600 6800 Dia. Length (mm) 22 22 25 22 22 25 22 25 30 22 25 30 35 25 30 25 30 35 30 35 30 35 35 22 22 22 25 22 25 22 25 30 22 25 30 35 25 30 25 30 35 30 35 30 35 35 35 (mm) 25 30 25 35 40 30 45 35 25 50 40 30 25 45 35 50 40 30 45 35 50 40 45 25 30 30 25 35 30 40 35 25 45 40 30 25 45 35 50 40 30 45 35 50 40 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC1K122HJ EETHC1K152HJ EETHC1K152JJ EETHC1K182HJ EETHC1K222HJ EETHC1K222JJ EETHC1K272HJ EETHC1K272JJ EETHC1K272KJ EETHC1K332HJ EETHC1K332JJ EETHC1K332KJ EETHC1K332LJ EETHC1K392JJ EETHC1K392KJ EETHC1K472JJ EETHC1K472KJ EETHC1K472LJ EETHC1K562KJ EETHC1K562LJ EETHC1K682KJ EETHC1K682LJ EETHC1K822LJ EETHC2A821HJ EETHC2A102HJ EETHC2A122HJ EETHC2A122JJ EETHC2A152HJ EETHC2A152JJ EETHC2A182HJ EETHC2A182JJ EETHC2A182KJ EETHC2A222HJ EETHC2A222JJ EETHC2A222KJ EETHC2A222LJ EETHC2A272JJ EETHC2A272KJ EETHC2A332JJ EETHC2A332KJ EETHC2A332LJ EETHC2A392KJ EETHC2A392LJ EETHC2A472KJ EETHC2A472LJ EETHC2A562LJ EETHC2A682LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 1.50 0.25 1.70 0.25 1.70 0.25 1.80 0.25 2.10 0.25 2.10 0.25 2.40 0.25 2.40 0.25 2.40 0.25 2.60 0.25 2.60 0.25 2.60 0.25 2.60 0.25 3.00 0.25 3.00 0.25 3.30 0.25 3.30 0.25 3.30 0.25 3.70 0.25 3.70 0.25 3.90 0.25 3.90 0.25 4.30 0.25 1.40 0.25 1.70 0.25 1.80 0.25 1.80 0.25 2.10 0.25 2.10 0.25 2.30 0.25 2.30 0.25 2.30 0.25 2.60 0.25 2.60 0.25 2.60 0.25 2.60 0.25 2.90 0.25 2.90 0.25 3.20 0.25 3.20 0.25 3.20 0.25 3.60 0.25 3.60 0.25 3.80 0.25 3.80 0.25 4.10 0.25 4.50 0.25 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 200 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 200 100 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 470 560 680 820 1000 1200 160 1500 1800 2200 2700 ✽ 3300 470 560 680 820 1000 180 1200 1500 1800 2200 ✽ 2700 Dia. Length (mm) 22 22 22 25 22 25 22 25 30 22 25 30 35 25 30 35 25 30 35 30 35 30 35 35 22 22 25 22 25 22 25 30 22 25 30 35 25 30 30 25 30 35 30 35 30 35 35 (mm) 25 30 30 25 35 30 40 35 25 45 40 30 25 45 35 30 50 40 30 45 35 50 40 50 25 30 25 35 30 40 30 25 45 40 30 25 45 30 35 50 40 30 45 35 50 40 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC2C471HJ EETHC2C561HJ EETHC2C681HJ EETHC2C681JJ EETHC2C821HJ EETHC2C821JJ EETHC2C102HJ EETHC2C102JJ EETHC2C102KJ EETHC2C122HJ EETHC2C122JJ EETHC2C122KJ EETHC2C122LJ EETHC2C152JJ EETHC2C152KJ EETHC2C152LJ EETHC2C182JJ EETHC2C182KJ EETHC2C182LJ EETHC2C222KJ EETHC2C222LJ EETHC2C272KJ EETHC2C272LJ EETHC2C332LJ EETHC2P471HC EETHC2P561HJ EETHC2P561JJ EETHC2P681HJ EETHC2P681JJ EETHC2P821HJ EETHC2P821JJ EETHC2P821KJ EETHC2P102HJ EETHC2P102JJ EETHC2P102KJ EETHC2P102LJ EETHC2P122JJ EETHC2P122KC EETHC2P122KJ EETHC2P152JJ EETHC2P152KJ EETHC2P152LJ EETHC2P182KJ EETHC2P182LJ EETHC2P222KJ EETHC2P222LJ EETHC2P272LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 1.40 0.15 1.50 0.15 1.70 0.15 1.70 0.15 2.00 0.15 2.00 0.15 2.20 0.15 2.20 0.15 2.20 0.15 2.30 0.15 2.30 0.15 2.30 0.15 2.30 0.15 2.50 0.15 2.50 0.15 2.50 0.15 2.70 0.15 2.70 0.15 2.70 0.15 2.90 0.15 2.90 0.15 3.10 0.15 3.10 0.15 3.30 0.15 1.45 0.15 1.50 0.15 1.50 0.15 1.70 0.15 1.70 0.15 2.00 0.15 2.00 0.15 2.00 0.15 2.20 0.15 2.20 0.15 2.20 0.15 2.20 0.15 2.30 0.15 2.30 0.15 2.30 0.15 2.50 0.15 2.50 0.15 2.50 0.15 2.70 0.15 2.70 0.15 2.90 0.15 2.90 0.15 3.10 0.15 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 200 100 200 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 200 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 390 470 560 680 820 1000 200 1200 1500 1800 ✽ 2200 270 330 390 470 560 680 220 820 1000 1200 1500 ✽ ✽ 1800 2200 Dia. Length (mm) 22 22 25 22 22 25 22 25 30 22 25 25 30 35 25 25 30 35 30 35 30 35 30 35 22 22 22 22 25 25 22 22 25 22 25 30 35 22 25 30 35 25 25 30 35 25 30 35 30 30 35 30 35 35 (mm) 25 30 25 30 40 30 45 35 25 50 40 45 30 25 45 50 35 30 40 30 45 40 50 45 25 25 30 35 25 30 35 40 30 45 35 25 25 50 40 30 25 45 50 35 30 50 40 35 45 50 40 50 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC2D391HJ EETHC2D471HJ EETHC2D471JC EETHC2D561HJ EETHC2D681HJ EETHC2D681JJ EETHC2D821HJ EETHC2D821JJ EETHC2D821KJ EETHC2D102HJ EETHC2D102JC EETHC2D102JJ EETHC2D102KJ EETHC2D102LJ EETHC2D122JC EETHC2D122JJ EETHC2D122KJ EETHC2D122LJ EETHC2D152KJ EETHC2D152LJ EETHC2D182KJ EETHC2D182LJ EETHC2D222KJ EETHC2D222LJ EETHC2Q271HJ EETHC2Q331HJ EETHC2Q391HJ EETHC2Q471HJ EETHC2Q471JC EETHC2Q471JJ EETHC2Q561HC EETHC2Q561HJ EETHC2Q561JJ EETHC2Q681HC EETHC2Q681JJ EETHC2Q681KJ EETHC2Q681LJ EETHC2Q821HC EETHC2Q821JJ EETHC2Q821KJ EETHC2Q821LJ EETHC2Q102JC EETHC2Q102JJ EETHC2Q102KJ EETHC2Q102LJ EETHC2Q122JC EETHC2Q122KJ EETHC2Q122LJ EETHC2Q152KC EETHC2Q152KJ EETHC2Q152LJ EETHC2Q182KC EETHC2Q182LJ EETHC2Q222LC Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 1.31 0.15 1.45 0.15 1.45 0.15 1.67 0.15 1.75 0.15 1.75 0.15 2.04 0.15 2.04 0.15 2.04 0.15 2.30 0.15 2.30 0.15 2.30 0.15 2.30 0.15 2.30 0.15 2.65 0.15 2.65 0.15 2.65 0.15 2.65 0.15 2.80 0.15 2.80 0.15 3.08 0.15 3.08 0.15 3.48 0.15 3.48 0.15 1.10 0.15 1.26 0.15 1.34 0.15 1.48 0.15 1.48 0.15 1.48 0.15 1.67 0.15 1.67 0.15 1.67 0.15 1.78 0.15 1.78 0.15 1.78 0.15 1.78 0.15 2.04 0.15 2.04 0.15 2.04 0.15 2.04 0.15 2.33 0.15 2.33 0.15 2.33 0.15 2.33 0.15 2.65 0.15 2.65 0.15 2.65 0.15 2.80 0.15 2.80 0.15 2.80 0.15 3.11 0.15 3.11 0.15 3.50 0.15 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 200 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 200 100 100 100 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 270 330 390 470 560 250 680 820 1000 1200 ✽ ✽ ✽ 1500 1800 150 180 220 270 330 390 315 470 560 680 820 ✽ 1000 Dia. Length (mm) 22 22 25 22 22 25 22 22 25 30 22 22 25 30 22 22 25 30 35 25 30 35 25 30 35 30 35 35 35 35 22 22 22 22 25 22 25 30 22 25 30 35 25 30 25 30 35 30 35 30 35 35 (mm) 25 30 25 30 35 25 35 40 30 25 40 45 35 25 45 50 40 30 25 45 35 30 50 40 30 45 35 45 45 50 25 30 30 40 30 45 35 25 50 40 30 25 45 35 50 40 30 45 35 50 40 45 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC2E271HJ EETHC2E331HJ EETHC2E331JJ EETHC2E391HC EETHC2E391HJ EETHC2E391JJ EETHC2E471HC EETHC2E471HJ EETHC2E471JJ EETHC2E471KJ EETHC2E561HC EETHC2E561HJ EETHC2E561JJ EETHC2E561KJ EETHC2E681HC EETHC2E681HJ EETHC2E681JJ EETHC2E681KJ EETHC2E681LJ EETHC2E821JJ EETHC2E821KJ EETHC2E821LJ EETHC2E102JC EETHC2E102KJ EETHC2E102LJ EETHC2E122KJ EETHC2E122LJ EETHC2E152LJ EETHC2E182LC EETHC2E182LJ EETHC2F151HJ EETHC2F181HJ EETHC2F221HJ EETHC2F271HC EETHC2F271JJ EETHC2F331HJ EETHC2F331JJ EETHC2F331KJ EETHC2F391HC EETHC2F391JJ EETHC2F391KJ EETHC2F391LJ EETHC2F471JJ EETHC2F471KJ EETHC2F561JJ EETHC2F561KJ EETHC2F561LJ EETHC2F681KJ EETHC2F681LJ EETHC2F821KJ EETHC2F821LJ EETHC2F102LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 1.10 0.15 1.20 0.15 1.20 0.15 1.30 0.15 1.30 0.15 1.30 0.15 1.40 0.15 1.40 0.15 1.40 0.15 1.40 0.15 1.50 0.15 1.50 0.15 1.50 0.15 1.50 0.15 1.70 0.15 1.70 0.15 1.70 0.15 1.70 0.15 1.70 0.15 2.00 0.15 2.00 0.15 2.00 0.15 2.20 0.15 2.20 0.15 2.20 0.15 2.30 0.15 2.30 0.15 2.50 0.15 2.50 0.15 2.70 0.15 0.82 0.15 0.90 0.15 1.00 0.15 1.10 0.15 1.10 0.15 1.20 0.15 1.20 0.15 1.20 0.15 1.30 0.15 1.30 0.15 1.30 0.15 1.30 0.15 1.40 0.15 1.40 0.15 1.50 0.15 1.50 0.15 1.50 0.15 1.70 0.15 1.70 0.15 2.00 0.15 2.00 0.15 2.30 0.15 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 200 100 200 100 100 100 100 100 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 200 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 120 150 180 220 270 330 350 390 470 560 680 ✽ ✽ 820 1000 Dia. Length (mm) 22 22 22 25 22 25 22 25 30 22 25 30 25 30 30 25 30 35 30 30 35 30 30 35 35 35 (mm) 25 30 30 25 35 30 40 35 25 45 40 30 45 30 35 50 35 30 40 45 35 45 50 40 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC2V121HJ EETHC2V151HJ EETHC2V181HJ EETHC2V181JJ EETHC2V221HJ EETHC2V221JJ EETHC2V271HC EETHC2V271JJ EETHC2V271KJ EETHC2V331HC EETHC2V331JJ EETHC2V331KJ EETHC2V391JJ EETHC2V391KC EETHC2V391KJ EETHC2V471JJ EETHC2V471KC EETHC2V471LJ EETHC2V561KC EETHC2V561KJ EETHC2V561LJ EETHC2V681KC EETHC2V681KJ EETHC2V681LJ EETHC2V821LJ EETHC2V102LC Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 0.75 0.15 0.82 0.15 0.90 0.15 0.90 0.15 1.00 0.15 1.00 0.15 1.10 0.15 1.10 0.15 1.10 0.15 1.20 0.15 1.20 0.15 1.20 0.15 1.30 0.15 1.30 0.15 1.30 0.15 1.40 0.15 1.40 0.15 1.40 0.15 1.50 0.15 1.50 0.15 1.50 0.15 1.70 0.15 1.70 0.15 1.70 0.15 1.90 0.15 1.90 0.15 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 100 200 100 100 100 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 100 120 150 180 220 270 400 330 390 470 560 ✽ ✽ 680 820 Dia. Length (mm) 22 22 22 25 22 25 22 22 25 30 22 22 25 30 35 25 30 30 35 25 30 30 35 30 35 30 30 35 35 35 (mm) 25 30 30 25 35 30 40 45 35 25 45 50 40 30 25 45 30 35 30 50 35 40 30 45 35 45 50 40 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC2G101HJ EETHC2G121HJ EETHC2G151HJ EETHC2G151JC EETHC2G181HJ EETHC2G181JJ EETHC2G221HC EETHC2G221HJ EETHC2G221JJ EETHC2G221KJ EETHC2G271HC EETHC2G271HJ EETHC2G271JJ EETHC2G271KJ EETHC2G271LJ EETHC2G331JJ EETHC2G331KC EETHC2G331KJ EETHC2G331LJ EETHC2G391JJ EETHC2G391KC EETHC2G391KJ EETHC2G391LJ EETHC2G471KJ EETHC2G471LJ EETHC2G561KC EETHC2G561KJ EETHC2G561LJ EETHC2G681LJ EETHC2G821LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 0.70 0.15 0.75 0.15 0.88 0.15 0.88 0.15 0.95 0.15 0.95 0.15 1.10 0.15 1.10 0.15 1.10 0.15 1.10 0.15 1.22 0.15 1.22 0.15 1.22 0.15 1.22 0.15 1.22 0.15 1.44 0.15 1.44 0.15 1.44 0.15 1.44 0.15 1.55 0.15 1.55 0.15 1.55 0.15 1.55 0.15 1.68 0.15 1.68 0.15 1.90 0.15 1.90 0.15 1.90 0.15 2.12 0.15 2.30 0.15 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 200 200 100 100 200 100 100 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 100 120 150 180 220 270 420 330 390 470 560 ✽ ✽ ✽ 680 Dia. Length (mm) 22 22 25 22 25 22 25 30 22 25 30 22 25 30 35 25 25 30 35 30 35 35 30 35 30 35 35 35 35 (mm) 25 30 25 35 30 40 30 25 45 35 25 50 40 30 25 45 50 35 35 40 30 35 45 35 50 40 45 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC2S101HJ EETHC2S121HJ EETHC2S121JJ EETHC2S151HJ EETHC2S151JJ EETHC2S181HJ EETHC2S181JJ EETHC2S181KJ EETHC2S221HJ EETHC2S221JJ EETHC2S221KJ EETHC2S271HJ EETHC2S271JJ EETHC2S271KJ EETHC2S271LJ EETHC2S331JC EETHC2S331JJ EETHC2S331KJ EETHC2S331LJ EETHC2S391KJ EETHC2S391LC EETHC2S391LJ EETHC2S471KJ EETHC2S471LJ EETHC2S561KJ EETHC2S561LC EETHC2S561LJ EETHC2S681LC EETHC2S681LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 0.70 0.15 0.74 0.15 0.74 0.15 0.84 0.15 0.84 0.15 0.91 0.15 0.91 0.15 0.91 0.15 1.05 0.15 1.05 0.15 1.05 0.15 1.20 0.15 1.20 0.15 1.20 0.15 1.20 0.15 1.42 0.15 1.42 0.15 1.42 0.15 1.42 0.15 1.55 0.15 1.55 0.15 1.55 0.15 1.71 0.15 1.71 0.15 1.90 0.15 1.90 0.15 1.90 0.15 2.10 0.15 2.10 0.15 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 100 100 200 100 100 100 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC ■ Standard Products Case size W.V. Cap. (120 Hz) (±20 %) (V. DC) (µF) 100 120 150 180 220 450 270 330 390 470 ✽ ✽ 560 Dia. Length (mm) 22 25 22 25 22 22 25 30 22 25 25 30 30 22 25 25 30 35 25 25 30 30 35 25 30 30 35 35 30 30 35 35 30 35 35 35 (mm) 30 25 35 30 35 40 30 25 45 35 40 25 30 50 40 45 30 25 45 50 35 40 30 50 40 45 30 35 45 50 35 40 50 40 45 50 Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) EETHC2W101HJ EETHC2W101JJ EETHC2W121HJ EETHC2W121JJ EETHC2W151HC EETHC2W151HJ EETHC2W151JJ EETHC2W151KJ EETHC2W181HJ EETHC2W181JC EETHC2W181JJ EETHC2W181KC EETHC2W181KJ EETHC2W221HJ EETHC2W221JC EETHC2W221JJ EETHC2W221KJ EETHC2W221LJ EETHC2W271JC EETHC2W271JJ EETHC2W271KC EETHC2W271KJ EETHC2W271LJ EETHC2W331JC EETHC2W331KC EETHC2W331KJ EETHC2W331LC EETHC2W331LJ EETHC2W391KC EETHC2W391KJ EETHC2W391LC EETHC2W391LJ EETHC2W471KC EETHC2W471LC EETHC2W471LJ EETHC2W561LJ Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) 0.64 0.20 0.64 0.20 0.72 0.20 0.72 0.20 0.79 0.20 0.79 0.20 0.79 0.20 0.79 0.20 0.87 0.20 0.87 0.20 0.87 0.20 0.87 0.20 0.87 0.20 1.00 0.20 1.00 0.20 1.00 0.20 1.00 0.20 1.00 0.20 1.19 0.20 1.19 0.20 1.19 0.20 1.19 0.20 1.19 0.20 1.38 0.20 1.38 0.20 1.38 0.20 1.38 0.20 1.38 0.20 1.55 0.20 1.55 0.20 1.55 0.20 1.55 0.20 1.74 0.20 1.74 0.20 1.74 0.20 1.90 0.20 Min. Packaging Q'ty (pcs) 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 200 100 100 200 200 100 100 200 100 100 100 100 100 100 100 100 100 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm ✽When capacitors of φ35҂45L and φ35҂50L are mounted on PWB, reinforce them with mounting clamp or adhesives. (Avoid using adhesives including halogenated compositions.) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008 Aluminum Electrolytic Capacitors/ HC (L:20 mm) ■ Standard Products (L:20 mm) Case size Part No. PET sleeve Terminal Length 4.0 mm (Without Top Plate) Specification Ripple tan δ Current (120 Hz) (120 Hz) (+20 °C) (+105 °C) max. (A r.m.s.) Min. Packaging Q'ty W.V. Cap. (120 Hz) (±20 %) Dia. Length (V. DC) (µF) (mm) max. (mm) 220 22 20 EETHC2D221HJ 0.85 0.15 200 270 25 20 EETHC2D271JJ 0.95 0.15 200 330 30 20 EETHC2D331KJ 1.10 0.15 200 390 30 20 EETHC2D391KJ 1.20 0.15 200 470 35 20 EETHC2D471LJ 1.41 0.15 200 560 35 20 EETHC2D561LJ 1.48 0.15 200 150 22 20 EETHC2E151HJ 0.69 0.15 200 180 25 20 EETHC2E181JJ 0.77 0.15 200 220 30 20 EETHC2E221KJ 0.95 0.15 200 270 30 20 EETHC2E271KJ 1.00 0.15 200 330 35 20 EETHC2E331LJ 1.16 0.15 200 200 250 400 450 (pcs) 390 35 20 EETHC2E391LJ 1.30 0.15 200 56 22 20 EETHC2G560HJ 0.40 0.15 200 68 25 20 EETHC2G680JJ 0.49 0.15 200 82 30 20 EETHC2G820KJ 0.55 0.15 200 100 30 20 EETHC2G101KJ 0.60 0.15 200 120 35 20 EETHC2G121LJ 0.75 0.15 200 150 35 20 EETHC2G151LJ 0.80 0.15 200 39 22 20 EETHC2W390HJ 0.36 0.20 200 47 25 20 EETHC2W470JJ 0.41 0.20 200 56 25 20 EETHC2W560JJ 0.43 0.20 200 68 30 20 EETHC2W680KJ 0.50 0.20 200 82 30 20 EETHC2W820KJ 0.53 0.20 200 100 35 20 EETHC2W101LJ 0.61 0.20 200 Endurance : 105 °C 2000 h, Terminal Pitch : 10 mm Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Jul. 2008