MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SOT−23, 6 Lead CASE 527AJ ISSUE B DATE 29 FEB 2012 SCALE 2:1 D A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DATUM C IS THE SEATING PLANE. B 6 5 4 1 2 3 E E1 DIM A A1 A2 b c D E E1 e L L2 GAGE PLANE 6X e L2 TOP VIEW b 0.20 SEATING PLANE L M C A S B S DETAIL A A2 c A 6X 0.10 C A1 C SIDE VIEW GENERIC MARKING DIAGRAM* DETAIL A SEATING PLANE END VIEW XXX MG G RECOMMENDED SOLDERING FOOTPRINT* 3.30 1 XXX = Specific Device Code M = Date Code G = Pb−Free Package (Note: Microdot may be in either location) 6X 0.85 6X 0.56 MILLIMETERS MIN MAX --1.45 0.00 0.15 0.90 1.30 0.20 0.50 0.08 0.26 2.70 3.00 2.50 3.10 1.30 1.80 0.95 BSC 0.20 0.60 0.25 BSC *This information is generic. Please refer to device data sheet for actual part marking. Pb−Free indicator, “G” or microdot “ G”, may or may not be present. 0.95 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: STATUS: 98AON34321E ON SEMICONDUCTOR STANDARD REFERENCE: © Semiconductor Components Industries, LLC, 2002 October, DESCRIPTION: 2002 − Rev. 0 SOT−23, 6 LEAD http://onsemi.com 1 Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. Case Outline Number: PAGE 1 OFXXX 2 DOCUMENT NUMBER: 98AON34321E PAGE 2 OF 2 ISSUE REVISION DATE O RELEASED FOR PRODUCTION FROM POD #SOT236−029−01 TO ON SEMICONDUCTOR. REQ. BY B. BERGMAN. 19 DEC 2008 A REDRAWN TO JEDEC STANDARDS. REQ. BY D. TRUHITTE. 12 JAN 2011 B CORRECTED LABEL FOR MOLDED BODY DIMENSION OF TOP VIEW TO E1. REQ. BY D. TRUHITTE. 29 FEB 2012 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. © Semiconductor Components Industries, LLC, 2012 February, 2012 − Rev. B Case Outline Number: 527AJ