pdf

www.osram.com/flex
LINEARlight Colormix Flex Protect – LF05CA-P / LF05CE-P
Technical Datasheet
Benefits
For outdoor use  IP67
High performance silicone:
 extreme long life time: 50.000 h
 high flexibility
Premounted feeder for easy connection
Attractive Design
Elegant white appearance
Electronic components hidden
Applications
Ships and boats, wall integration
Machine lighting
Path illumination, illuminated signs
Architectural lighting
LF05CA-RGB3-P
LF05CE-RGB1-P
11
11
100
4,000
20
150
6,000
30
[mm]
[mm]
4.5
4.5
Quick reference
Product
LF05CA-RGB3-P
LF05CE-RGB1-P
Order Code
Color
4008321977205
RGB
4008321977182
Dominant
Wavelength
W/m
lm/m
lm/W
Shipping Units
18,0
435
24
8
Red
625
6,7
114
17
Green
525
9,5
298
32
Blue
465
1,9
23
12
6,5
180
28
16
RGB
Red
625
2,7
120
Green
525
3,1
292
34
Blue
465
0,7
23
11
8
Technical features
Protection Type
IP 67 (outdoor use)
High performance Silicone
High UV-resistancy
Saltmist proof
Dimmable
Pulse width modulation (PWM)
Lifetime (L70B50 @ Tc=40°C)
50,000 h
Adhesive tape on backside
Tesa (High Performance Tape)
Fulfilled standards/tests
Flammability: Glow-wire test with 850° – EN60598-1
Mixed gas corrosion test – IEC60068-2-60
Complementary systems
CONNECTsystem PROTECT, SLIM TRACK, OPTOTRONIC
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Subject to change without notice. Errors and omissions excepted. Version: 2014-05-06
LINEARlight Colormix Flex® Protect – LF05CA-P / LF05CE-P
TECHNICAL DATASHEET
1/4
www.osram.com/flex
Technical operating data (for overall module)
Product
LF05CA-RGB3-P
LF05CE-RGB1-P
Order Code
Color
Voltage
[V]
Power
[W]
Current
[A]
Luminous
Flux [lm]
Radiance
Angle [°]
Overall
Length
4008321977205
RGB
24
72
3
1740
120
4m
120
6m
Red
24
27
1,1
456
Green
24
38
1,6
1193
4008321977182
Blue
24
7
0,3
92
RGB
24
39
1,6
1080
Red
24
16
0,7
1161
Green
24
19
0,8
2822
Blue
24
4
0,2
222
Minimum & maximum ratings
LF05CA/E-P
Operating temperature
at Tc-Point [°C]
-30 … +75°C
Storage temperature
[°C]
-40 … +85°C
Voltage range
[V dc]
23 … 25 V
Reverse Voltage
[V dc]
25 V
► Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED Module.
► Exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the LED Module.
► The temperature of the LED module must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a
temperature sensor or a temperature sensitive label. Drive all channels on 100% to determine the temperature. For exact location of the
Tc-point see drawing below.
Technical drawings
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Subject to change without notice. Errors and omissions excepted. Version: 2014-05-06
LINEARlight Colormix Flex® Protect – LF05CA-P / LF05CE-P
TECHNICAL DATASHEET
2/4
www.osram.com/flex
Safety information
► The module has to be protected from mechanical loads
► Assembly must not damage or destroy conducting paths on the circuit board.
► Installation of LED modules (with power supplies) needs to be made with regard to all applicable and safety standards. Only qualified
personnel should be allowed to perform installations.
► Observe correct polarity!
Depending on the product incorrect polarity will lead to emission of no light. The module can be damaged after a few seconds. To prevent
this, correct polarity immediately! (see "reverse voltage", page 2)
► Parallel connection is highly recommended as safe electrical operation mode.
Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module.
► ESD protection methods have to be observed when cutting and connecting the module. on ESD handling in the application note ESD
protection for LED modules.
► The LED Module must not be operated under water
► Please ensure that the power supply is of adequate power to operate the total load.
In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilized SELV
power supply protecting against short circuits, overload and overheating.
To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC
certified. In Europe the declarations of conformity must include the following standards:
CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384.
Also check for the mark of an independent authorized certification institute.
Please see the relevant brochure for more detailed information (see "Related and Further Information")
OSRAM OPTOTRONIC® control gear complies to all relevant standards and guarantees safe operation.
Assembly Information
► The smallest electrical unit (SEU) (100mm / 150mm- 5 LEDs) can be removed by cutting at the printed marks at the side.
► After cutting connect the module via CONNECTsystem PROT. Insert module into connector and apply pressure on a hard surface until
locked.
► The mounting of the single LED coupons is facilitated by means of the double-sided adhesive on the back surface of the module. Care
must be taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. The mounting substrate
must have sufficient structural integrity. Take care to completely remove the adhesive backing. Once the module is appropriately
positioned, press on the module with about 20N/cm² (refer to application techniques of Tesa adhesive transfer tapes).
To support adhesion at higher temperatures, use additional mounting brackets if temperature exceeds Tc = 40°C.
► The minimum bending radius is 5 cm.
► When installing in environments with large variations in temperature (e.g. outdoor applications) and operating length of more than 2 m, the
use of adequate mounting surfaces is necessary . Otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress
of any mismatch in expansion.
► If temperature exceeds Tc = 40°C, additional mounting brackets are needed.
► Pay attention to avoid highly corrosive atmospheres, e.g. permanent high humidity or Hydrogen Sulfide (H2S).
With current LED technology, H2S is causing accelerated corrosion which will lead to shortened timelife or premature failure.
Sources for H2S may be rubber, foamed rubber, soft-foam-tapes, sealings on rubber basis, natural sources (e.g. sulfur springs), etc.
To avoid H2S from sulfur-vulcanized rubber it is necessary to switch to silicon based materials or rubber that is Peroxid-crosslinked.
Indication may be found in the material datasheet of the rubber supplier.
Complementary systems and accessories
Accessories
Type
CONNECTsystem PROTECT
Endcap for module
4pin Feeder
4pin Jumper
SLIM TRACK System
SLIM TRACK
Mounting Bracket for SLIM TRACK
SLIM TRACK Cover, very low, clear
SLIM TRACK Cover, hight, diffuse
Silicone Endcap for LF-LTS-COVER-DIFFUSE
Product
EAN
Shipping units
LF-ENDCAP PROTECT
LF-4PIN PROTECT
LF-4CONN PROTECT
4008321977106
4008321977076
4008321977090
10
5
5
LF-LTS-2100 SLIM TRACK
LF-LTS-MB
LF-LTS COVER C
LF-LTS-COVER-DIFFUSE
LF-LTS-ENDCAP
4008321978981
4008321979025
4008321790187
4008321979001
4008321979049
40
35 / 280
40
40
20 / 160
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Subject to change without notice. Errors and omissions excepted. Version: 2014-05-06
LINEARlight Colormix Flex® Protect – LF05CA-P / LF05CE-P
TECHNICAL DATASHEET
3/4
www.osram.com/flex
OPTOTRONIC
► Please consider that lengths may differ if further controls are installed.
Product reference
EAN10
LF05CA-RGB3-P
4008321977205
LF05CE-RGB1-P
4008321977182
4008321113269
4008321040169
4050300618111
4050300662626
4052899043497
4052899905566
4050300817477
4008321362476
4008321981684
4008321981707
4008321981721
up to 0,3 m
up to 0,4 m
up to 1,1 m
up to 1,1 m
up to 1,6 m
up to 2,7 m
up to 4,1 m ⁽*⁾
up to 4,1 m ⁽*⁾
up to 4,4 m ⁽*⁾
up to 6,6 m ⁽*⁾
up to 13,3 m ⁽*⁾
up to 0,9 m
up to 1,2 m
up to 3 m
up to 3 m
up to 4,5 m
up to 7,65 m ⁽**⁾
up to 11,4 m ⁽**⁾
up to 11,4 m ⁽**⁾
up to 12,3 m ⁽**⁾
up to 18,45 m ⁽**⁾
up to 36,9 m ⁽**⁾
4008321187796
4008321808363
4008321964403
4008321371560
4008321981677
4008321981691
4008321981714
up to 3,3 m
up to 4,4 m ⁽*⁾
up to 3,6 m
up to 4,1 m ⁽*⁾
up to 4,4 m ⁽*⁾
up to 6,6 m ⁽*⁾
up to 13,3 m ⁽*⁾
up to 9,15 m ⁽**⁾
up to 12,3 m ⁽**⁾
up to 9,9 m ⁽**⁾
up to 11,4 m ⁽**⁾
up to 12,3 m ⁽**⁾
up to 18,45 m ⁽**⁾
up to 36,9 m ⁽**⁾
Non-dimmable
OPTOTRONIC OT 6/200-240/24 CE
OPTOTRONIC OT 8/200-240/24
OPTOTRONIC OT 20/220-240/24
OPTOTRONIC OT 20/120-240/24 S
OPTOTRONIC OT 30/220-240/24 P
OPTOTRONIC OT 50/220-240/24
OPTOTRONIC OT 75/220-240/24
OPTOTRONIC OT 75/220-240/24 E
OPTOTRONIC OT 80/220-240/24 P
OPTOTRONIC OT 120/220-240/24 P
OPTOTRONIC OT 240/220-240/24 P
Dimmable
OPTOTRONIC OT EASY 60 II
OPTOTRONIC OT EASY 80
OPTOTRONIC OT 65/220-240/24 3DIM E
OPTOTRONIC OTi DALI 75/220-240/24 1-4 CH
OPTOTRONIC OT 80/220-240/24 DIM P
OPTOTRONIC OT 120/220-240/24 DIM P
OPTOTRONIC OT 240/220-240/24 DIM P
⁽*⁾ Total length operable per driver. Length of single strip or series connection may not exceed 4 m.
⁽**⁾ Total length operable per driver. Length of single strip or series connection may not exceed 6 m.
Maximim length per OT:
lA + lB + lC + …  lmax/OT
lA
Maximum length per strip:
lB
lA
lB
lC
l…
OT – 24V
lC
≤
≤
≤
≤
4m (CA), 6m (CE)
4m (CA), 6m (CE)
4m (CA), 6m (CE)
4m (CA), 6m (CE)
Contacts & information
German engineering meets Italian elegance – creating a European product
All LINEARlight Flex® Protect are Made in Italy by OSRAM, with over 100 years of experience in light solutions.
OSRAM GmbH
Marcel-Breuer-Straße 6
80807 Munich, Germany
www.osram.com
+49.89.6213-0
Sales and technical support is given by the local OSRAM
subsidiaries.
On the OSRAM website all subsidiaries are listed with
complete address and phone numbers.
OSRAM LED Systems
OSRAM: FLEXIBLE LED MODULES
OSRAM catalogue
General information
www.osram.com/led-systems
www.osram.com/flex
http://catalog.osram.com
www.osram.com
Due to the special conditions of manufacturing processes of LED, the typical data of technical parameters can only reflect statistical figures and do not necessarily
correspond to the actual parameters of each single product which could differ from the typical data.
Subject to change without notice. Errors and omissions excepted. Version: 2014-05-06
LINEARlight Colormix Flex® Protect – LF05CA-P / LF05CE-P
TECHNICAL DATASHEET
4/4