www.osram.com/LED-Systems LINEARlight Colormix Flex - LF05C Data Sheet Benefits Picture for Datasheet is missing !!! Flexible self-adhesive module for special coloreffects and moods Each LED contains red, green and blue emitters: optimum colormixing Applications Light boxes / back lighting Edge-coupling of transparent or diffuse materials Path illumination, contour accentuation Technical Operating Data Product Color Number of LEDs Voltage [V DC]* Power [W]* Current [A]* Radiance Angle [°]* Wavelength [nm] Color Temp [K]* Lum. Flux [lm]* LF05CA-RGB3 LF05CA-RGB3 red green 200 200 24 24 26,7 37,9 1,1 1,6 120 120 625 nm 525 nm 447 1170 LF05CA-RGB3 LF05CE-RGB1 LF05CE-RGB1 blue red green 200 200 200 24 24 24 7,5 16,1 18,6 0,3 0,7 0,8 120 120 120 465 nm 625 nm 525 nm 90 298 724 LF05CE-RGB1 blue 200 24 4,4 0,2 120 465 nm 57 *) All Data are related to the entire module Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. This product was not optimized for white light illumination. +) Preliminary Data Technical Features Total power of the flexible LED strip: Easy connection with optional CONNECTsystem LF05CA: 72 W; LF05CE: 39 W LF-xx Flex: Feeder LF-4PIN Flex, connector LFCONN-10 Flex and LF-CONN-150 Flex. Luminous flux (@Tc=25°C): Easy mounting by adhesive tape on isolated LF05CA: 1700 lm; LF05CE: 1075 lm Size of printed circuit board (L x W x H): Depending on product and operational mode up LF05CA: 4000 mm x 8 mm x 2,2 mm LF05CE: 6000 mm x 8 mm x 2,2 mm to 50,000 h lifetime Smallest unit of 5 LEDs can be cut out at regular intervals without damaging the rest of the module. Length of smallest unit: LF05CA: 100 mm; LF05CE: 150 mm LF05C - 30.08.2011 backside Page 1 of 4 Dimmable by pulse width modulation (PWM) Minimum and Maximum Ratings Product Operating Temperature at Tc-Point [ °C ] * Storage Temperature [ °C ] * Voltage Range [ V dc ] * Reverse Voltage [ V dc ] * LF05CA-RGB3 -30 ... 75 -40 ... 85 23 ... 25 25 LF05CE-RGB1 -30 ... 75 -40 ... 85 23 ... 25 25 *) Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED Module. Exceeding maximum ratings for operating voltage will cause hazardous overload and will likely destroy the LED Module. The temperature of the LED module must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. Drive all channels on 100% to determine the temperature. For exact location of the Tc-point see drawing below. Drawings Drawing is missing !!! LF05C - 30.08.2011 Page 2 of 4 Safety Information The LED module itself and all its components must not be mechanically stressed. Assembly must not damage or destroy conducting paths on the circuit board. In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilised power supply protecting against short circuits, overload and overheating. To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. In Europe the declarations of conformity must include the following standards: CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384. Also check for the mark of an independent authorized certification institute. Please see the relevant brochure for more detailed information (see "Related and Further Information") OSRAM OPTOTRONIC® electronic control gear complies to all relevant standards and guarantees safe operation. Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. Observe correct polarity! Depending on the product incorrect polarity will lead to emission of red or no light. The module can be destroyed! Correct polarity immediatelly! (see "reverse voltage", page 2) Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module. Please ensure that the power supply is of adequate power to operate the total load. When mounting on metallic or otherwise conductive surfaces, there needs to be an electrical isolation at soldering points between module and the mounting surface. The maximum run length from any power feed should be limited to 4000 mm for the LF05CA and to 6000 mm for the LF05CE. Pay attention to standard ESD precautions when installing the module. Damage by corrosion will not be honored as a materials defect claim. It is the user´s responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements. For applications involving exposure to humidity and dust the module must be protected by a fixture or housing with a suitable protection class. The module can be protected against condensation water by treatment with an appropriate circuit board grade conformal coating. The conformal coating should have the following features: - Optical transparency - UV-resistance - thermal expansion matching the thermal expansion of the module 15-30*10^-6 cm/cm/K - low permeability of steam for all climatic conditions - resistance against corrosive environment Dimming/ colorcontrolling is only possible with PWM. The LINEARlight Colormix Flex is driven ideally by OSRAM OPTORONIC power supplies and controllgear. Controllgear is available with 1..10V, DALI or DMX interface. Please see our brochure "A new approach to light" or "Just as colorful as nature". Please refer to the maximum currents of the controllgear when calculating the whole installation (OT DIM: 5A, Oti DIM: 5A, OT DMX, 3-Channel DIM or Sequencer: 2A per channel). Please read our OPTOTRONIC technical installation guide for more detailed information about calculation and wiring diagrams. LF05C - 30.08.2011 Page 3 of 4 Assembly Information The module can be connected easily and without any tools with the optional connect system LF-4PIN Flex. Please note the maximum ampacity. Connection with soldering wires on unmounted module: Do not pretin the solderpads (marked "24V +/RGB")but pretin the wires and solder for max 4 s at 300 °C. Allow solderpoints to completely cool down before the next soldering. Prevent shear- or peel forces. Soldering of wires with the module mounted on a heatsink: Pretin solderpads and wires and solder for max 3 s at 350 °C. Allow solderpoints to completely cool down before the next soldering. Prevent shear- or peel forces. The mounting of the module is facilitated by means of the double-sided adhesive on the back-surface of the module. Care must be taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particle. The mounting substrate must have sufficient structural integrity. Take care to completely remove the protective film. Once the module is appropriately positioned, press on the module with about 20N/cm² (refer to application techniques of 3M adhesive transfer tapes). The minimum bending radius is 2 cm. The thermal length expansion coefficient of the modul is 17*10^-6cm/cm/K. When installing in environments with large variations in temperature (e.g. outdoor applications) and operating length of more than 2 m, the use of metallic mounting surfaces is necessary. Otherwise it is advisable to use an additional thicker adhesive tape to absorb the stress of any mismatch in expansion coefficients. Ordering Guide S-Unit * Productgroup Productname EAN * LINEARlight Colormix Flex LF05CA-RGB3 4008321592644 8 LINEARlight Colormix Flex LF05CE-RGB1 4008321593375 8 *) EAN: Ordering number per single module S-Unit: Modules per shipping unit Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves. Sales and Technical Support OSRAM GmbH Hellabrunner Strasse 1 D - 81536 München Germany www.osram.com +49 (0)89 6213-0 Sales and technical support is given by the local OSRAM subsidiaries. On our world wide homepage all OSRAM subsidiaries are listed with complete address and phone numbers. Related and Further Information A new aproach to light 1EZW001GB www.osram.com/led-systems-downloads 130 T008 GB www.osram.com/ecg-downloads www.osram.com/led-systems www.osram.com/led-systems-downloads 130 W011 GB www.osram.com/ecg-download OPTOTRONIC® Technical Guide OSRAM LED systems Application Note: ESD New standards for LED control gear LF05C - 30.08.2011 Page 4 of 4