4.8W Gate Drive DC-DC Converter P5AGDC-Series ● ● ● ● ● DIL24 package Dual output 3000 VDC isolation -40...85°C operating temperature range Efficiency up to 85 % Model guide Type P5AGDC12-1509 P5AGDC24-1509 + Output Input voltage range Voltage [VDC] [VDC] 9…18 18…36 15 15 - Output Current min. [mA] 10 10 Voltage max. [mA] 200 200 [VDC] -9 -9 Current min. [mA] -10 -10 max. [mA] -200 -200 Input current @ no @ full load load min. max. [mA] [mA] 470 16 235 8 Efficiency [%] Capacitive load max. [µF] 85 85 1000 1000 Specifications Input: Filter No load power consumption Reflected input ripple current Capacitance @100 kHz, 0.1V Output Output voltage tolerance Input voltage regulation Load regulation, 5%..100% load Transient recovery time Transient response deviation Temperature coefficient Ripple (BW 30 MHz), see figure 1 Noise (BW 30 MHz), see figure 1 Short circuit duration Over voltage protection Physical I/O Isolation, test <1mA,1min. Isolation Resistance @ 500 VDC Switching frequency Package material Weight Reliability, MTBF (MIL-HDBK-217 @ 25 °C) Environmental EMI CE incl. with filter figure 1 PI-type 0.3 W max. 20 mA, typ (see figure 4) 100 pF, typ. EMI RE incl. with filter figure 1 ESD RS EFT Vo 15 V: ±2 %, Vo -9 V: ±5 % ± 0.5 % max. @ full Vin change ± 1% 500 ms, max. @ 25 % load step 5 µs, max. @ 25 % load step 0.03 % / °C max., at full load 30 mVp-p max. 200 mVp-p max. Continuous, automatic restart 110…140 % of Vout. nominal IEC-, EN61000-4-2 IEC-, EN61000-4-3 IEC-, EN61000-4-4 Surge IEC-, EN61000-4-5 CS IEC-, EN61000-4-6 Voltage dips, short and interrutions immunity IEC-, EN61000-4-29 Operating ambient temperature Storage temperature Case temperature rise at Ta 25°C and full load Storage humidity Cooling Absolute maximum ratings P5AGDC12-1509 Vin max. P5AGDC24-1509 Vibration x- ,y- and z- axes Lead soldering temperature 1.5 mm distance from body 3 kVDC 109 Ω min. 300 kHz, typ. Epoxy resin (UL94-V0) 14 g 1 Mio. hours CISPR22 / EN55022 CLASS A (only with filter see figure 1) CISPR22 / EN55022 CLASS A (only with filter see figure 1) Contact ± 4 kV perf.crit. B 10 V/m perf.crit. A ±2 kV perf.crit. B, (only with filter see figure 1) ±2 kV perf.crit. B, (only with filter see figure 1) 3 Vrms perf.crit. A 0…70% perf.crit. B -40 °C to +85 °C (see derating) -55 °C to +125 °C 40 °C max. Up to 95 %, non condensing Free air convection -0.7 ~ 25 VDC -0.7 ~ 50 VDC 10 G, 10…55 Hz, 30 Min. 300 °C max. 10 s Typical application circuit IGBT driver unit Signal input +Vin Vin 100 µF 63 V P5AGDCxx-1509 +Vout Com 100 µF 35 V 10 µF Ceramic -Vout 100 µF 35 V 10 µF Ceramic -Vin Application Notes: 1. The wire between the converter and IGBT driver must as short as possible. 2. External filter capacitors should be connected as close as possible to the IGBT driver. 3. To ensure the high peak gate current, the filter capacitors should be electrolytic capacitor and ceramic capacitor collocation. 4. The input average power of the IGBT driver should be less than the output power of DC-DC converter. Page 1 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 4.8W Gate Drive DC-DC Converter P5AGDC-Series Figure 1 LCM Fuse +Vin P5AGDC12-1509 +Vout + Input DC D1 C1 CX CX Com. DC -Vout -Vin - Input Recommended EMS circuit Recommended EMi circuit LDM Fuse PIF004A LCM P5AGDC24-1509 +Vin +Vout + Input DC D1 C1 ΔU CX CX Com. Filter MOV DC -Vout -Vin - Input Recommended EMS circuit Type P5AGDC12-1509 P5AGDC24-1509 Fuse 1A 0.63 A Recommended EMi circuit MOV 10D560K LDM 56 µH D1 SMCJ28A SMCJ48A C1 680 µF 120 µF CX 4.7 µF 4.7 µF LCM 1 mH 3 mH Filter PIF004A Page 2 of 5 Deutschland : Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 4.8W Gate Drive DC-DC Converter P5AGDC-Series Recommended EMC optimized PCB layout Figure 2 Test circuit for reflected input ripple current The input reflected ripple current is measured with an inductor Lin and capacitor Cin to simulate source impedance. Measure point Figure 4 + Input + Vin Lin 4.7 µH + Vout DC Load - Input Cin 220 µF ESR < 1 Ω at 100 kHz DC - Vin - Vout Recommended circuit All converter have been tested according to the following recommended testing circuit before leaving factory (see Figure 3). If you want to further decrease the output ripple, you can increase a capacitance properly or choose capacitors with low ESR, the greatest capacitance of its filter capacitor must less than the max. capacitive load. Figure 3 + Input + Vin Cout DC Cin - Input + Vout - Vin DC Cout - Vout Note: 1. 2. 3. 4. 5. The wire between converter and IGBT driver must be as short as possible. External filter capacitors must be placed so near as possible to converter and IGBT driver. The average power of the IGBT driver must be less than the output power of the DC-DC converter. The maximum capacitive load is tested at nominal input voltage and full load. Unless otherwise noted, all specifications are measured at Ta 25 °C, humidity <75 %, nominal input voltage and rated output load. 6. All characteristics are listed models, and non-standard models may perform differently. 7. Please contact our technical support for any specific requirement. 8. Specifications of this product are subject to changes without prior notice. 9. These products have no overload protection. Protection with a fuse is the simplest method. 10. It is not recommended to increase the output power capability by connecting two or more converters in parallel operation. 11. The converters are not hot swappable and not parallel usable Page 3 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 4.8W Gate Drive DC-DC Converter P5AGDC-Series Efficiency diagrams Page 4 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 4.8W Gate Drive DC-DC Converter P5AGDC-Series Dimensions Pin 2 3 9 11 14 16 22 23 P5AGDC - Vinput - Vinput Common - Voutput + Voutput Common + Vinput + Vinput Unit: mm Pin tolerances ± 0.1 mm General tolerances ± 0.25 mm Tube dimensions Unit : mm General tolerances: ± 0.50 mm Short tube L=220 mm, quantity per tube: 6pcs Long tube L=530 mm, quantity per tube: 15 pcs PHI-CON is a trademark of HY-LINE Power Components. Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for use carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 03.14 f Page 5 of 5 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]