Datasheet UM7222 Rev08

UM7222MA/7222/7222A
High-Speed USB2.0 (480 Mbps) DPDT Switch
UM7222MA MSOP10
UM7222 QFN10 1.8×1.4
UM7222A QFN10 2.1×1.6
General Description
The UM7222MA/UM7222/UM7222A is a dual port high-speed, low-power data switch optimized
for USB 2.0 signal switching. The UM7222MA/UM7222/UM7222A switch is configured in
double-pole/ double-throw DPDT. It handles bidirectional signal flow, achieving a 550 MHz -3dB
bandwidth, and a port to port crosstalk and isolation at -50dB at 250MHz.
The UM7222MA/UM7222/UM7222A operates from a single +2.7V to +5.5V supply, with
current consumption less than 1 microampere.
The UM7222MA/UM7222/UM7222A features wide bandwidth and low bit-to-bit skew allow it to
pass high-speed differential signal with good signal integrity, offers little or no attenuation of the
high-speed signals at the outputs. Its high channel-to-channel crosstalk rejection results in
minimal noise interface. Its bandwidth is wide enough to pass high-speed USB 2.0 differential
signals (480Mbps). The control logic threshold is guaranteed to be compatible with 1.8V logic.
The UM7222MA is available in Pb-free MSOP10 package, the UM7222 is available in Pb-free
QFN10 package (1.4mm×1.8mm×0.55mm), while the UM7222A is available in Pb-free QFN10
package (2.1mm×1.6mm×0.55mm), they are ideal for portable high speed mix signal switching
application.
Applications
Features








Differential Signal Data Routing
USB2.0 Signal Routing
Cell Phone, PDA, Digital Camera and
Notebook
LCD Monitor, TV, and Set-top Box








Ron is Typically 6.5Ω at VCC=3.0V
Low Bit-to-Bit Skew: Typically 50ps
OVT on D+ and D- up to 5.5V
Power OFF Protection:
When VCC=0V, D+ and D- can Tolerate up to
5.5V
Low Crosstalk: -50dB (250MHz)
Low Current Consumption: 1µA
Near-Zero Propagation Delay: 250ps
Channel On-Capacitance: 6.5pF(Typical)
VCC Operating Range: +2.7V to +5.5V
550MHz Bandwidth(or Data Frequency)
Lead (Pb)-Free MSOP10 and QFN10
Package
ESD Rating: ±4kV I/O to GND
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
1/12
UM7222MA/7222/7222A
Pin Configurations
Top View
10
1
10
HSD1+
2
9
OE
HSD2+
3
8
HSD1-
D+
4
7
HSD2-
GND
5
6
D-
8
7
6
UM7222
MA
XX
VCC
S
9
1
2
3
4
5
XX: Week Code
UM7222MA
MSOP10
OE
8
VCC
9
S
10
HSD1-
HSD2-
7
6
CONTROL
1
2
HSD1+
HSD2+
5
D-
4
GND
3
D+
AC
M
(Top View)
M: Month Code
UM7222
QFN10 1.8×1.4
OE
9
HSD1-
HSD2-
D-
8
7
6
AP
VCC
10
5
CONTROL
1
S
2
3
4
HSD1+
HSD2+
D+
M
(Top View)
GND
M: Month Code
UM7222A
QFN10 2.1×1.6
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
2/12
UM7222MA/7222/7222A
Pin Description
Pin
UM7222MA
2
3
4
5
Pin
UM7222
1
2
3
4
Pin
UM7222A
2
3
4
5
6
7
8
9
10
1
5
6
7
8
9
10
6
7
8
9
10
1
Name
Function
HSD1+
HSD2+
D+
GND
Data Ports
Data Ports
Data Ports
Ground Connection
DHSD2HSD1-
Data Ports
Data Ports
Data Ports
Output Enable
Positive Supply Voltage
Select Input
______
OE
VCC
S
Ordering Information
Part Number
Packaging Type
Marking Code
UM7222MA
MSOP10
UM7222MA
UM7222
QFN10 1.8mm×1.4mm
AC
UM7222A
QFN10 2.1mm×1.6mm
AP
Shipping Qty
3000pcs/13 Inch
Tape & Reel
3000pcs/7 Inch
Tape & Reel
3000pcs/7 Inch
Tape & Reel
Function Table
OE
1
0
0
S
X
0
1
HSD1+, HSD1OFF
ON
OFF
HSD2+, HSD2OFF
OFF
ON
Absolute Maximum Ratings
Symbol
VCC
VIS
VIN
ID
PD
TO
TSTG
Parameter
Supply Voltage
Analog Switch Input Voltage
Digital Select Input Voltage
Continuous DC Current
Power Dissipation
Operating Temperature Range
Storage Temperature Range
Limit
- 0.5 to + 6.5
-0.5 to +6.5
- 0.5 to + 6.5
50
0.5
- 40 to +85
- 65 to +150
Unit
V
mA
W
°C
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
3/12
UM7222MA/7222/7222A
DC Electrical Characteristics
Limits (–40 to 85 °C)
Typ
Min
Max
(Note1)
Symbol
Parameter
Test
Conditions
IIN
Input Leakage Current
0≤VIS≤VCC
3.6
Full
-1.0
1.0
μA
0≤VIS≤VCC
0
Full
-1.0
1.0
μA
VIN = 2.6V
3.6
Full
10
μA
0≤VIS≤VCC
3.6
Full
1.0
μA
ICC
Power Off Leakage
Current
Increase in ICC per
Control Voltage
OFF State Leakage
Current
Quiescent Supply
Current
VIS =VCC or
GND
3.6
Full
1.0
μA
VIH
Input High Voltage
VIL
Input Low Voltage
VIK
Clamp Diode Voltage
IIS=-18mA
RON
On-Resistance (Note2)
IOFF
ICCT
IOZ
ΔRON
RFLAT
On Resistance Match
Between Channels
(Note2,3)
On Resistance Flatness
(Note2,3)
Vcc(V)
Temp
3.0
to3.6
3.0 to
3.6
Full
-1.0
1.3
Unit
V
Full
0.5
V
3.0
Full
-1.2
V
VIS =0 to 0.4 V
ID=8mA
3.0
Full
6.5
9
Ω
VIS =0 to 0.4 V
ID=8mA
3.0
Full
0.35
Ω
VIS =0 to 1.0 V
ID=8mA
3.0
Full
4.5
Ω
Note 1: Typically values are at VCC=3.3V and TA=+25℃.
Note 2: Guaranteed by design. Resistance measurements do not include test circuit or package
resistance.
Note 3: Parameter is characterized but not tested in production.
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
4/12
UM7222MA/7222/7222A
AC Electrical Characteristics
Symbol
Parameter
Test
Conditions
tON
Turn On Time
VIS =0.8V
tOFF
Turn Off Time
VIS =0.8V
tBBM
Break Before Make
Time (Note 4)
VIS =0.8V
tPD
Propagation Delay
CL=10pF
tSK(O)
Channel to Channel
Skew
CL = 10pF
OIRR
Off Isolation
XTALK
Crosstalk
BW
-3 dB Bandwidth
RL=50Ω,
f = 250MHz
RL=50Ω,
f = 250MHz
RL=50Ω
Limits (–40 to 85 °C)
Vcc(V)
Temp
3.0 to
3.6
3.0 to
3.6
3.0 to
3.6
3.0 to
3.6
3.0 to
3.6
3.0 to
3.6
3.0 to
3.6
3.0 to
3.6
Unit
Typ
(Note1)
Max
Full
13
30
ns
Full
12
25
ns
4.7
6.5
ns
Min
Full
Full
2
0.25
ns
0.05
ns
Full
-25
dB
Full
-48
dB
Full
550
MHz
2.5
pF
4.5
pF
7.0
pF
Capacitance
CIN
COFF
CON
Control Pin Input
Capacitance
(Note5)
HSD+ HSD- Off
Capacitance (Note5)
HSD+ HSD- ON
Capacitance (Note5)
VCC = 0V
VCC =VIS=
3.3V, OE=3.3V
VCC =3.3V,
OE=0V
Note 4: Guaranteed by design.
Note 5: TA=+25℃, f=1MHz, Capacitance is characterized but not tested in production.
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
5/12
UM7222MA/7222/7222A
Typical Performance Characteristics
35
RON vs VD and Single Supply Voltage
30
O
RON-ON Resistance (ohm)
V+=3.0V
RON-ON Resistance(ohm)
T=25 C
ION=8mA
30
25
V+=3.3V
20
15
V+=3.6V
10
5
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
25
V+=3.3V
ION=8mA
0
T=25 C
15
10
5
0.5
1.0
Switching Threshold vs Supply Voltage
2.0
2.5
3.0
3.5
Supply Current vs Input Switching Frequency
25
20
VIH
V+=3.6V
15
I+-Supply Current(uA)
VT-Switching Threshold(V)
1.5
VD-Analog Voltage(V)
VD-Analog Voltage(V)
1.20
1.15
1.10
1.05
1.00
0.95
0.90
0.85
0.80
0.75
0.70
0.65
0.60
0.55
0.50
3.0
0
T=85 C
20
0
0.0
4.0
RON vs Analog Voltage and Temperature
VIL
10
5
0
-5
V+=3.3V
-10
V+=3.0V
-15
-20
3.1
3.2
3.3
3.4
V+-Supply Voltage(V)
3.5
3.6
-25
10
100
1K
10K
100K
1M
Input Switching Frequency(Hz)
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
6/12
10M
UM7222MA/7222/7222A
Typical Performance Characteristics (Continued)
Bandwidth
0.3
1
10
100
1000
Frequency (MHz)
Off Isolation
0.3
1
10
100
1000
Frequency (MHz)
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
7/12
UM7222MA/7222/7222A
Typical Performance Characteristics (Continued)
Crosstalk
0.3
1
10
100
1000
Frequency (MHz)
Applications Information
Power-Off Protection
For a VBUS short circuit, the switch is expected to withstand such a condition for at least 24
hours. The UM7222 has specially designed circuitry which prevents unintended signal bleed
through as well as guaranteed system reliability during a power-down, over-voltage condition.
The protection has been added to the common pins (D+, D-).
Power-On Protection
The USB 2.0 specification also notes that the USB device should be capable of withstanding a
VBUS short during transmission of data. This modification works by limiting current flow back
into the V+ rail during the over-voltage event so current remains within the safe operating range.
In this application, the switch passes the full 5.25V input signal through to the selected output
while maintaining specified off isolation on the un-selected pins.
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
8/12
UM7222MA/7222/7222A
Package Information
UM7222MA MSOP10
Outline Drawing
D
DIMENSIONS
E
E1
L
θ
Symbol
MILLIMETERS
INCHES
Min
Typ
Max
Min
Typ
Max
A
-
-
1.10
-
-
0.043
A1
0.00
-
0.15
0.000
-
0.006
A2
0.75
0.85
0.95
0.030
0.033
0.037
A3
0.25
0.35
0.39
0.010
0.014
0.015
b
0.18
-
0.27
0.007
-
0.011
INDEX
2
1
e
b
c
0.15
-
0.20
0.006
-
0.008
2.90
3.00
3.10
0.114
0.118
0.122
E
2.90
3.00
3.10
0.114
0.118
0.122
E1
4.70
4.90
5.10
0.185
0.193
0.201
e
0.40
0.50
0.60
0.016
0.020
0.024
L
0.40
0.60
0.80
0.016
0.024
0.031
θ
0º
-
8º
0º
-
8º
End View
A3
A1
A
A2
Top View
c
D
Side View
Land Pattern
0.5
5.7
2.5
1.6
4.1
0.3
NOTES:
1. Compound dimension: 3.00×3.00;
2. Unit: mm;
3.General tolerance ±0.05mm unless otherwise
specified;
4. The layout is just for reference.
Tape and Reel Orientation
UM7222
MA
XX
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
9/12
UM7222MA/7222/7222A
UM7222 QFN10 1.8×1.4
Outline Drawing
DIMENSIONS
b
D
L1
PIN 1
IDENTIFICATION
e
E
L
Symbol
MILLIMETERS
Typ
Max
Min
Typ
Max
A
0.50
0.55
0.60
0.020
0.022
0.024
A1
0.00
-
0.05
0.000
-
0.002
A3
BOTTOM VIEW
0.15REF
0.006REF
b
0.15
0.20
0.25
0.006
0.008
0.010
D
1.35
1.40
1.45
0.054
0.056
0.058
E
1.75
1.80
1.85
0.069
0.071
0.073
A
TOP VIEW
INCHES
Min
A3
A1
e
SIDE VIEW
0.40BSC
0.016BSC
L
0.30
0.40
0.50
0.012
0.016
0.020
L1
0.40
0.50
0.60
0.016
0.020
0.024
Land Pattern
1.70
9×0.563
0.663
0.40
2.10
1
10×0.225
NOTES:
1. Compound dimension: 1.80×1.40;
2. Unit: mm;
3.General tolerance ±0.05mm unless otherwise
specified;
4. The layout is just for reference.
Tape and Reel Orientation
AC
M
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
10/12
UM7222MA/7222/7222A
UM7222A QFN10 2.1×1.6
Outline Drawing
DIMENSIONS
b
e
D
1
L1
L
E
0.8
Symbol
0.3
Top View
A
Bottom View
MILLIMETERS
Min
Typ
Max
Min
Typ
Max
A
0.50
0.55
0.60
0.020
0.022
0.024
A1
0.00
-
0.05
0.000
-
0.002
A3
0.15REF
A3
A1
0.006REF
b
0.20
0.25
0.30
0.008
0.010
0.012
D
2.05
2.10
2.15
0.082
0.084
0.086
E
1.55
1.60
1.65
0.062
0.064
0.066
e
Side View
INCHES
0.50BSC
0.020BSC
L
0.35
0.40
0.45
0.014
0.016
0.018
L1
0.40
0.45
0.50
0.016
0.018
0.020
Land Pattern
1.62
0.11
1.12
0.35
0.56
0.50
0.25
NOTES:
1. Compound dimension: 2.10×1.60;
2. Unit: mm;
3.General tolerance ±0.05mm unless otherwise
specified;
4. The layout is just for reference.
Tape and Reel Orientation
AP
M
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
11/12
UM7222MA/7222/7222A
IMPORTANT NOTICE
The information in this document has been carefully reviewed and is believed to be
accurate. Nonetheless, this document is subject to change without notice. Union assumes
no responsibility for any inaccuracies that may be contained in this document, and makes
no commitment to update or to keep current the contained information, or to notify a
person or organization of any update. Union reserves the right to make changes, at any
time, in order to improve reliability, function or design and to attempt to supply the best
product possible.
Union Semiconductor, Inc
Add: Unit 606, No.570 Shengxia Road, Shanghai 201210
Tel: 021-51093966
Fax: 021-51026018
Website: www.union-ic.com
________________________________________________________________________
http://www.union-ic.com Rev.08 Jan.2015
12/12