TDK5100F

D at a S h ee t , V 1. 2 , A pr i l 20 0 8
TDK5100F
434 M Hz ASK/ FS K Transm i tte r in 10 -p in
Package
W i re l e s s C o n t r o l
Co mpo ne nts
N e v e r
s t o p
t h i n k i n g .
Edition 2008-04-04
Published by Infineon Technologies AG,
Am Campeon 1-12,
85579 Neubiberg, Germany
© Infineon Technologies AG 2008-04-04.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office in Germany or the Infineon Technologies Companies and our Infineon Technologies
Representatives worldwide (www.infineon.com).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
D at a S h ee t , V 1. 2 , A pr i l 20 0 8
TDK5100F
434 M Hz ASK/ FS K Transm i tte r in 10 -p in
Package
W i re l e s s C o n t r o l
Co mpo ne nts
N e v e r
s t o p
t h i n k i n g .
TDK5100F
Revision History:
2008-04-04
Previous Version:
V1.1 as of November 2005
V 1.2
Page
Subjects (major changes since last revision)
31-33, 35
Added Min.-/Max.-values of output power and supply current
31, 33, 35
Added values of frequency range and for possible extension of frequency
range
We Listen to Your Comments
Any information within this document that you feel is wrong, unclear or missing at all?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
[email protected]
TDK5100F
Table of Contents
Page
1
1.1
1.2
1.3
1.4
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Order Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2.1
2.2
2.3
2.4
2.4.1
2.4.2
2.4.3
2.4.4
2.4.4.1
2.4.4.2
2.4.4.3
2.4.4.4
2.4.5
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin Definition and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Functional Block Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PLL Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Power Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PLL Enable Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Transmit Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power mode control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Recommended Timing Diagrams for ASK- and FSK-Modulation . . . . . 17
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 Ohm-Output Testboard Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 Ohm-Output Testboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bill of Material (50 Ohm-Output Evalboard) . . . . . . . . . . . . . . . . . . . . . . . .
Stripline-Antenna Testboard Schematic . . . . . . . . . . . . . . . . . . . . . . . . . .
Stripline-Antenna Testboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bill of Material (Antenna board) FSK modulation . . . . . . . . . . . . . . . . . . . .
Application Hints on the Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . .
Design Hints on the Clock Output (CLKOUT) . . . . . . . . . . . . . . . . . . . . . .
Application Hints on the Power-Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . .
19
19
20
21
22
23
24
25
27
28
4
4.1
4.1.1
4.2
4.3
4.3.1
4.3.2
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC/DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC/DC Characteristic at 3V, 25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC/DC Characteristic at 2.1V ...4.0 V, -40°C ...+125°C . . . . . . . . . . . .
30
30
30
31
31
31
33
5
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Data Sheet
5
6
6
6
6
6
V 1.2, 2008-04-04
TDK5100F
Product Description
1
Product Description
1.1
Overview
The TDK 5100 F is a single chip ASK/FSK transmitter for operation in the frequency band
433-435 MHz. The IC offers a high level of integration and needs only a few external
components. The device contains a fully integrated PLL synthesizer and a high efficiency
power amplifier to drive a loop antenna. A special circuit design and an unique power
amplifier design are used to save current consumption and therefore to save battery life.
Additional features are a power down mode and a divided clock output.
1.2
•
•
•
•
•
•
•
•
•
•
•
•
•
fully integrated frequency synthesizer
VCO without external components
ASK and FSK modulation
frequency range 433-435 MHz
high efficiency power amplifier (typically 5 dBm)
low supply current
voltage supply range 2.1 ... 4 V
temperature range −40 ... +125°C
power down mode
crystal oscillator 13.56 MHz
FSK-switch
divided clock output for µC
low external component count
1.3
•
•
•
•
•
Features
Application
Tire pressure monitoring systems
Keyless entry systems
Remote control systems
Alarm systems
Communication systems
1.4
Order Information
Table 1
Type
TDK5100F
Order Information
Ordering Code
Package
SP000014745
PG-TSSOP-10
available on tape and reel
Data Sheet
6
V 1.2, 2008-04-04
TDK5100F
Functional Description
2
Functional Description
2.1
Pin Configuration
Figure 1
2.2
CLKOUT
1
10
PDWN
VS
2
9
PAOUT
GND
3
8
PAGND
FSKOUT
4
7
FSKDTA
COSC
5
6
ASKDTA
TDK 5100F
IC Pin Configuration
Pin Definition and Functions
Table 2
Pin Definition and Functions - Overview
Pin
No.
Symbol
Function
1
CLKOUT
Clock Driver Output (847.5 kHz)
2
VS
Voltage Supply
3
GND
Ground
4
FSKOUT
Frequency Shift Keying Switch Output
5
COSC
Crystal Oscillator Input (13.56 MHz)
6
ASKDTA
Amplitude Shift Keying Data Input
7
FSKDTA
Frequency Shift Keying Data Input
8
PAGND
Power Amplifier Ground
9
PAOUT
Power Amplifier Output (434 MHz)
10
PDWN
Power Down Mode Control
Data Sheet
7
V 1.2, 2008-04-04
TDK5100F
Functional Description
Table 3
Pin Definition and Function1)
Pin
No.
Symbol
1
CLKOUT
Interface Schematic
Function
Clock output to supply an external
device.
An external pull-up resistor has to
be added in accordance to the
driving requirements of the
external device.
VS
1
300 Ω
The clock frequency is 847.5 kHz.
2
VS
This pin is the positive supply of
the transmitter electronics.
An RF bypass capacitor should be
connected directly to this pin and
returned to GND (pin 3) as short
as possible.
3
GND
General ground connection.
4
FSKOUT
This pin is connected to a switch to
GND (pin 3).
VS
VS
The switch is closed when the
signal at FSKDTA (pin 7) is in a
logic low state.
200 µA
120 kΩ
4
The switch is open when the signal
at FSKDTA (pin 7) is in a logic high
state.
200 kΩ
FSKOUT can switch an additional
capacitor to the reference crystal
network to pull the crystal
frequency by an amount resulting
in the desired FSK frequency shift
of the transmitter output
frequency.
Data Sheet
8
V 1.2, 2008-04-04
TDK5100F
Functional Description
Pin
No.
Symbol
5
COSC
Interface Schematic
Function
VS
VS
6 kΩ
5
This pin is connected to the
reference oscillator circuit.
The reference oscillator is working
as a negative impedance
converter. It presents a negative
resistance in series to an
inductance at the COSC pin.
100 µA
6
ASKDTA
VS
Digital amplitude modulation can
be imparted to the Power Amplifier
through this pin.
+1.2 V
60 kΩ
6
+1.1 V
90 kΩ
50 pF
Data Sheet
30 µA
9
A logic high (ASKDTA > 1.5 V or
open) enables the Power
Amplifier.
A logic low (ASKDTA < 0.5 V)
disables the Power Amplifier.
V 1.2, 2008-04-04
TDK5100F
Functional Description
Pin
No.
Symbol
7
FSKDTA
Interface Schematic
VS
Function
Digital frequency modulation can
be imparted to the Xtal Oscillator
by this pin. The VCO-frequency
varies in accordance to the
frequency of the reference
+1.1 V oscillator.
+1.2 V
60 kΩ
7
90 kΩ
30 µA
A logic high (FSKDTA > 1.5V or
open) sets the FSK switch to a
high impedance state.
A logic low (FSKDTA < 0.5 V)
closes the FSK switch from
FSKOUT (pin 4) to GND (pin 3).
A capacitor can be switched to the
reference crystal network this way.
The Xtal Oscillator frequency will
be shifted giving the designed FSK
frequency deviation.
Data Sheet
10
V 1.2, 2008-04-04
TDK5100F
Functional Description
Pin
No.
Symbol
8
PAGND
Interface Schematic
Function
9
9
PAOUT
10
PDWN
8
Ground connection of the power
amplifier.
The RF ground return path of the
power amplifier output PAOUT
(pin 9) has to be concentrated to
this pin.
RF output pin of the transmitter.
A DC path to the positive supply
VS has to be supplied by the
antenna matching network.
Disable pin for the complete
transmitter circuit.
VS
40 µA ∗ (ASKDTA+FSKDTA)
A logic low (PDWN < 0.7 V) turns
off all transmitter functions.
5 kΩ
10
"ON"
A logic high (PDWN > 1.5 V) gives
access to all transmitter functions.
150 kΩ
PDWN input will be pulled up by
40 µA internally by either setting
FSKDTA or ASKDTA to a logic
high-state.
250 kΩ
1) Indicated voltages and currents apply for PLL Enable Mode and Transmit Mode.
In Power Down Mode, the values are zero or high-ohmic.
Data Sheet
11
V 1.2, 2008-04-04
Figure 2
Data Sheet
Crystal
13.56 MHz
FSK
Switch
5
4
XTAL
Osc
12
Ground
Clock
Output
LF
VCO
Power
Supply
2
Power
Supply
VS
3
:64
OR
10
Power
Down
Control
1
:16
PFD
6
ASK
Data
Input
:2
Power
AMP
On
Power
Amplifier
Output
Power
Amplifier
Ground
9
8
2.3
7
FSK
Data
Input
TDK5100F
Functional Description
Functional Block Diagram
Functional Block Diagram
V 1.2, 2008-04-04
TDK5100F
Functional Description
2.4
Functional Block Description
2.4.1
PLL Synthesizer
The Phase Locked Loop synthesizer consists of a Voltage Controlled Oscillator (VCO),
an asynchronous divider chain, a phase detector, a charge pump and a loop filter. It is
fully implemented on chip. The tuning circuit of the VCO consisting of spiral inductors
and varactor diodes is on chip, too. Therefore no additional external components are
necessary. The nominal center frequency of the VCO is 868 MHz. The oscillator signal
is fed both, to the synthesizer divider chain and to the power amplifier. The overall
division ratio of the asynchronous divider chain is 64. The phase detector is a Type IV
PD with charge pump. The passive loop filter is implemented on chip.
2.4.2
Crystal Oscillator
The crystal oscillator operates at 13.56 MHz.
The crystal frequency is divided by 16. The resulting 847.5 kHz are available at the clock
output CLKOUT (pin1) to drive the clock input of a micro controller.
To achieve FSK transmission, the oscillator frequency can be detuned by a fixed amount
by switching an external capacitor via FSKOUT (pin 4).
The state of the switch is controlled by the signal at FSKDTA (pin 7).
Table 4
FSKDTA - FSK Switch
FSKDTA (pin7)
FSK Switch
Low1)
CLOSED
2)
3)
Open , High
OPEN
1) Low:
Voltage at pin < 0.5V
2) Open:
Pin open
3) High:
Voltage at pin > 1.5V
2.4.3
Power Amplifier
The VCO frequency is divided by 2 and fed to the Power Amplifier.
The Power Amplifier can be switched on and off
by the signal at ASKDTA (pin 6).
Data Sheet
13
V 1.2, 2008-04-04
TDK5100F
Functional Description
Table 5
ASKDTA - Power Amplifier
ASKDTA (pin6)
Power Amplifier
1)
Low
OFF
Open2), High3)
ON
1) Low:
Voltage at pin < 0.5V
2) Open:
Pin open
3) High:
Voltage at pin > 1.5V
The Power Amplifier has an Open Collector output at PAOUT (pin 9) and requires an
external pull-up coil to provide bias. The coil is part of the tuning and matching LC
circuitry to get best performance with the external loop antenna. To achieve the best
power amplifier efficiency, the high frequency voltage swing at PAOUT (pin 9) should be
twice the supply voltage.
The power amplifier has its own ground pin PAGND (pin 8) in order to reduce the amount
of coupling to the other circuits.
2.4.4
Power Modes
The IC provides three power modes, the POWER DOWN MODE, the PLL ENABLE
MODE and the TRANSMIT MODE.
2.4.4.1
Power Down Mode
In the POWER DOWN MODE the complete chip is switched off.
The current consumption is typically 0.3 nA at 3 V 25°C.
This current doubles every 8°C. The values for higher temperatures are
typically 14 nA at 85°C and typically 600 nA at 125°C.
2.4.4.2
PLL Enable Mode
In the PLL ENABLE MODE the PLL is switched on but the power amplifier is turned off
to avoid undesired power radiation during the time the PLL needs to settle. The turn on
time of the PLL is determined mainly by the turn on time of the crystal oscillator and is
less than 1 ms when the specified crystal is used.
The current consumption is typically 3.5 mA (in PLL Enable Mode).
Data Sheet
14
V 1.2, 2008-04-04
TDK5100F
Functional Description
2.4.4.3
Transmit Mode
In the TRANSMIT MODE the PLL is switched on and the power amplifier is turned on too.
The current consumption of the IC is typically 7 mA when using a proper transforming
network at PAOUT, see Figure 8.
2.4.4.4
Power mode control
The bias circuitry is powered up via a voltage V > 1.5 V at the pin PDWN (pin10).
When the bias circuitry is powered up, the pins ASKDTA and FSKDTA are pulled up
internally.
Forcing the voltage at the pins low overrides the internally set state.
Alternatively, if the voltage at ASKDTA or FSKDTA is forced high externally, the PDWN
pin is pulled up internally via a current source. In this case, it is not necessary to connect
the PDWN pin, it is recommended to leave it open.
The principle schematic of the power mode control circuitry is shown in Figure 3
PDWN
ASKDTA
OR
FSKDTA
On
Bias
Source
Bias Voltage
120 kΩ
120 kΩ
On
PLL
434
MHz
FSK
PA
FSKOUT
PAOUT
IC
Figure 3
Data Sheet
Power mode control circuitry
15
V 1.2, 2008-04-04
TDK5100F
Functional Description
Table 6 provides a listing of how to get into the different power modes
Table 6
PDWN
1)
Power Modes
FSKDTA
ASKDTA
Low
Low, Open
Low, Open
Open2)
Low
Low
High3)
Low, Open, High
Low
Open
High
Low
High
Low, Open, High
Open, High
Open
High
Open, High
Open
Low, Open, High
High
1) Low:
MODE
POWER DOWN
PLL ENABLE
TRANSMIT
Voltage at pin < 0.7V (PDWN)
Voltage at pin < 0.5V (FSKDTA, ASKDTA)
2) Open:
Pin open
3) High:
Voltage at pin > 1.5V
Other combinations of the control pins PDWN, FSKDTA and ASKDTA are not
recommended.
Data Sheet
16
V 1.2, 2008-04-04
TDK5100F
Functional Description
2.4.5
Recommended Timing Diagrams for ASK- and FSK-Modulation
ASK Modulation using FSKDTA and ASKDTA, PDWN not connected
Modes:
Power Down
PLL Enable
Transmit
High
FSKDTA
Low
to
t
DATA
Open, High
ASKDTA
Low
to
t
min. 1 msec.
Figure 4
ASK Modulation
FSK Modulation using FSKDTA and ASKDTA, PDWN not connected.
Modes:
Power Down
PLL Enable
Transmit
DATA
High
FSKDTA
Low
to
t
to
t
High
ASKDTA
Low
min. 1 msec.
Figure 5
Data Sheet
FSK Modulation
17
V 1.2, 2008-04-04
TDK5100F
Functional Description
Alternative ASK Modulation, FSKDTA not connected.
Modes:
Power Down
PLL Enable
Transmit
High
PDWN
Low
to
t
DATA
Open, High
ASKDTA
Low
to
t
min. 1 msec.
Figure 6
Alternative ASK Modulation
Alternative FSK Modulation
Modes:
Power Down
PLL Enable
Transmit
High
PDWN
Low
to
t
Open, High
ASKDTA
Low
to
t
DATA
Open, High
FSKDTA
Low
to
t
min. 1 msec.
Figure 7
Data Sheet
Alternative FSK Modulation
18
V 1.2, 2008-04-04
TDK5100F
Applications
3
Applications
3.1
50 Ohm-Output Testboard Schematic
Figure 8
Data Sheet
50 Ohm-output testboard schematic
19
V 1.2, 2008-04-04
TDK5100F
Applications
3.2
50 Ohm-Output Testboard Layout
Figure 9
Top Side of TDK5100 F-Testboard with 50 Ohm-Output
Figure 10
Bottom Side of TDK5100 F-Testboard with 50 Ohm-Output
Data Sheet
20
V 1.2, 2008-04-04
TDK5100F
Applications
3.3
Bill of Material (50 Ohm-Output Evalboard)
Re fe re nce
R1
R2
R3
R4
R5
R6
R7
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
L1
L2
X1
X2
X3
X4
X5
X6
X7
JP1
JP2
Q1
IC1
Va lue
open
open
4k7
12k
open
15k
open
10p
6p8
open
open
100p
12p
39p
330p
3p3
47n
47n
120n
n.e.
n.e.
Pin
Pin
SMA-connector
SMA-connector
n.e.
solder bridge
solder bridge
13,56875 MHz,
TDK5100F
Spe cifica tion
0603, +/-5%
0603, +/-5%
0603, +/-5%
0603, C0G, +/-1%
0603, C0G, +/-0,1p
0603, X7R, +/-10%
0603, C0G, +/-1%
0603, C0G, +/-1%
0603, C0G, +/-5%
0603, C0G, +/-0,1p
0603, X7R, +/-10%
EPCOS SIMID 0603-C, +/-2%
EPCOS SIMID 0603-C, +/-2%
single-pole connector, 2,54mm
single-pole connector, 2,54mm
in position "XTAL"
in position "FSK"
Tokyo Denpa TSS-3B 13,56875 MHz Spec.No. 10-50205
Please note:
If R2 is placed (Clk Out is activated) a 47nF capacitor has to be used for C4.
Data Sheet
21
V 1.2, 2008-04-04
TDK5100F
Applications
3.4
Figure 11
Data Sheet
Stripline-Antenna Testboard Schematic
Stripline-antenna testboard schematic
22
V 1.2, 2008-04-04
TDK5100F
Applications
3.5
Stripline-Antenna Testboard Layout
Figure 12
Top Side of TDK5100 F-Testboard with Stripline-Antenna
Figure 13
Bottom Side of TDK5100 F-Testboard with Stripline-Antenna
Please note that this board layout may be used for both high- and low-power
applications, see also the bill of materials on the subsequent pages.
In case of ASK operation the solder bridge JP2 has to be shortened in the “ASK”position, in case of FSK modulation in the“FSK” position.
Solder bridge JP1between C1, C2 and C3) gives a choice of operating the board with
the on-board crystal as reference (“XTAL” shortened, i.e. close to C1 and C2) or with an
external clock generator (solder bridge shorts pads between C3 and C2).
Data Sheet
23
V 1.2, 2008-04-04
TDK5100F
Applications
3.6
Bill of Material (Antenna board) FSK modulation
Reference
R1
R2
R3
R4
R5
R6
R7
R8
R9
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
L1
L2
X1
X3
X4
S1
JP1
JP2
Q1
IC1
IC2
BAT1
Data Sheet
Value
open
0R
0R
82k
open
open
100n
39R
15k
10p
6p8
open
open
open
10n
5p6
open
4p7
47n
100n
0R
n.e.
n.e.
n.e.
push-button
solder bridge
solder bridge
13,56875 MHz,
TDK5100F
HCS360
battery holder
battery
Specification
0603, SMD-Jumper
0603, SMD-Jumper
0603, +/-5%
0603, X7R, +/-10%
0603, +/-1%
0603, +/-5%
0603, C0G, +/-1%
0603, C0G, +/-0,1p
0603, X7R, +/-10%
0603, C0G, +/-0,1p
0603, C0G, +/-0,1p
0603, X7R, +/-10%
0603, EPCOS SIMID, +/-2%
0603, SMD-Jumper
STTSKHMPW, ALPS
in position "XTAL"
in position "FSK"
Tokyo Denpa TSS-3B 13,56875 MHz Spec.No. 10P-TSSOP-10
SO8
HU2031-1, Renata
CR2032, Renata
24
V 1.2, 2008-04-04
TDK5100F
Applications
3.7
Application Hints on the Crystal Oscillator
Application Hints on the crystal oscillator
The crystal oscillator achieves a turn on time less than 1 msec when the specified crystal
is used. To achieve this, a NIC oscillator type is implemented in the TDK 5100 F. The
input impedance of this oscillator is a negative resistance in series to an inductance.
Therefore the load capacitance of the crystal CL (specified by the crystal supplier) is
transformed to the capacitance Cv.
-R
L
f, CL Cv
IC
Figure 14
Application Hints
Formula 1:
Cv =
1
1
+ ω 2L
CL
CL:
crystal load capacitance for nominal frequency
ω:
angular frequency
L:
inductance of the crystal oscillator
Example for the ASK-Mode:
Referring to the application circuit, in ASK-Mode the capacitance C2 is replaced by a
short to ground. Assume a crystal frequency of 13.56MHz and a crystal load capacitance
of CL = 12 pF. The inductance L at 13.56MHz is about 4.6 µH. Therefore C1 is calculated
to 10 pF.
Cv =
Data Sheet
1
1
+ω 2L
CL
25
= C1
V 1.2, 2008-04-04
TDK5100F
Applications
Example for the FSK-Mode:
FSK modulation is achieved by switching the load capacitance of the crystal as shown
below.
FSKDTA
FSKOUT
Csw
-R
L
f, CL Cv1
Cv2
COSC
IC
Figure 15
FSK Mode
The frequency deviation of the crystal oscillator is multiplied with the divider factor N of
the Phase Locked Loop to the output of the power amplifier. In case of small frequency
deviations (up to +/- 1000 ppm), the two desired load capacitances can be calculated
with the formula below.
CL ± =
2(C 0 + CL )
∆f
(1 +
)
N * f1
C1
∆f
2(C 0 + CL )
1±
(1 +
)
N * f1
C1
CL m C 0
CL:
crystal load capacitance for nominal frequency
C0:
shunt capacitance of the crystal
f:
frequency
ω:
ω = 2πf: angular frequency
N:
division ratio of the PLL
df:
peak frequency deviation
Because of the inductive part of the TDK 5100 F, these values must be corrected by
Formula 1 on the preceding page.
Data Sheet
26
V 1.2, 2008-04-04
TDK5100F
Applications
The value of Cv± can be calculated as
Cv ± =
1
1
+ω 2L
CL ±
If the FSK switch is closed, Cv- is equal to Cv1 (C1 in the application diagram). If the
FSK switch is open, Cv2 (C2 in the application diagram) can be calculated.
Cv 2 = C 2 =
Csw:
Csw ∗ Cv1 − (Cv + ) ∗ (Cv1 + Csw )
(Cv + ) − Cv1
parallel capacitance of the FSK switch (3 pF incl. layout parasitics)
Remark: These calculations are only approximations. The necessary values depend
on the layout also and must be adapted for the specific application board.
3.8
Design Hints on the Clock Output (CLKOUT)
The CLKOUT pin is an open collector output. An external pull up resistor (RL) should be
connected between this pin and the positive supply voltage. The value of RL is
depending on the clock frequency and the load capacitance CLD (PCB board plus input
capacitance of the microcontroller). RL can be calculated to:
RL =
Table 7
1
fCLKOUT * 8 * CLD
Clock Output
fCLKOUT=847.5 kHz
Remark:
Data Sheet
CL[pF]
RL[kOhm]
5
27
10
12
20
6.8
To achieve a low current consumption and a low
spurious radiation, the largest possible RL should be chosen.
27
V 1.2, 2008-04-04
TDK5100F
Applications
Even harmonics of the signal at CLKOUT can interact with the crystal oscillator input
COSC preventing the start-up of oscillation. Care must be taken in layout by sufficient
separation of the signal lines to ensure sufficiently small coupling.
3.9
Application Hints on the Power-Amplifier
The power amplifier operates in a high efficient class C mode. This mode is
characterized by a pulsed operation of the power amplifier transistor at a current flow
angle of θ<<π. A frequency selective network at the amplifier output passes the
fundamental frequency component of the pulse spectrum of the collector current to the
load. The load and its resonance transformation to the collector of the power amplifier
can be generalized by the equivalent circuit of Figure 16. The tank circuit L//C//RL in
parallel to the output impedance of the transistor should be in resonance at the
operating frequency of the transmitter.
VS
L
Figure 16
C
RL
Equivalent power amplifier tank circuit
The optimum load at the collector of the power amplifier for “critical” operation under
idealized conditions at resonance is:
R LC =
V S2
2 * PO
The theoretical value of RLC for an RF output power of Po= 5 dBm (3.16 mW) is:
R LC =
32
= 1423 Ω
2 * 0 .00316
“Critical” operation is characterized by the RF peak voltage swing at the collector of the
PA transistor to just reach the supply voltage VS.
The high degree of efficiency under “critical” operating conditions can be explained by
the low power losses at the transistor. During the conducting phase of the transistor, its
collector voltage is very small. This way the power loss of the transistor, equal to iC*uCE
is minimized. This is particularly true for small current flow angles of θ<<π.
Data Sheet
28
V 1.2, 2008-04-04
TDK5100F
Applications
In practice the RF-saturation voltage of the PA transistor and other parasitics reduce the
“critical” RLC.
The output power Po is reduced by operating in an “overcritical” mode characterised by
RL > RLC.
The power efficiency (and the bandwidth) increase when operating at a slightly higher
RL, as shown in Figure 17.
The collector efficiency E is defined as
E=
PO
VS I C
The diagram of Figure 17 was measured directly at the PA-output at VS = 3 V. Losses in
the matching circuitry decrease the output power by about 1.5 dB. As can be seen from
the diagram, 550 Ω is the optimum impedance for operation at 3 V. For an approximation
of ROPT and POUT at other supply voltages those two formulas can be used:
ROPT ~ VS
and
POUT ~ ROPT
10*E
Po [mW]
7
6
5
4
3
10*E
2
Po
1
0
0
1000
2000
3000
RL [Ohm]
Figure 17
Output power Po (mW) and collector efficiency E vs. load resistor RL.
The DC collector current Ic of the power amplifier and the RF output power Po vary with
the load resistor RL. This is typical for overcritical operation of class C amplifiers. The
collector current will show a characteristic dip at the resonance frequency for this type of
“overcritical” operation. The depth of this dip will increase with higher values of RL.
Data Sheet
29
V 1.2, 2008-04-04
TDK5100F
Reference
4
Reference
4.1
Electrical Data
4.1.1
Absolute Maximum Ratings
Attention: The maximum ratings must not be exceeded under any circumstances,
not even momentarily and individually, as permanent damage to the IC
will result.
Table 8
Absolute Maximum Ratings, Tamb = -40 °C … +125 °C
Parameter
Symbol
Limit Values
Unit
Remarks
min.
max.
Junction Temperature
TJ
−40
+150
°C
Storage Temperature
Ts
−40
+125
°C
Thermal Resistance
RthJA
220
K/W
Supply voltage
VS
−0.3
+4.0
V
Voltage at any pin
excluding pin 9
Vpins
-0.3
VS + 0.3
V
Voltage at pin 9
Vpin9
-0.3
2 * VS
V
No ESD-Diode to VS
ESD integrity, all pins
VESD
-1
+1
kV
JEDEC Standard
JESD22-A114-B
ESD integrity, all pins
excluding pin 9
VESD
-2
+2
kV
JEDEC Standard
JESD22-A114-B
Ambient Temperature under bias: TA = −40°C to +125°C
Note: All voltages referred to ground (pins) unless stated otherwise.
Pins 3 and 8 are grounded.
Data Sheet
30
V 1.2, 2008-04-04
TDK5100F
Reference
4.2
Operating Ratings
Within the operational range the IC operates as described in the circuit description.
Table 9
Operating Ratings
Parameter
Symbol
Limit Values
min.
max.
Unit
Supply voltage
VS
2.1
4.0
V
Ambient temperature
TA
-40
125
°C
4.3
Test Conditions
AC/DC Characteristics
AC/DC characteristics involve the spread of values guaranteed within the specified
supply voltage and ambient temperature. Typical charcateristics are the median of the
production.
4.3.1
AC/DC Characteristic at 3V, 25°C
Table 10
Supply Voltage VS=3V, Ambient temperature Tamb=25°C
Parameter
Symbol
Limit Values
min.
typ.
max.
Unit Test
Conditions
Current consumption
Power Down mode
IS PDWN
0.3
100
nA
V (Pins 10, 6
and 7)
< 0.2 V
PLL Enable mode
IS PLL_EN
3.5
4.2
mA
Transmit mode
434 MHz
IS TRANSM
7.7
10.4
mA
434.5
442
MHz fOUT = 32 * fCOSC
Output frequency
Output frequency
fOUT
427
Clock Driver Output (Pin 1)
Output current (High)
ICLKOUT
5
µA
VCLKOUT = VS
Saturation Voltage
(Low)1)
VSATL
0.56
V
ICLKOUT = 1 mA
Data Sheet
31
V 1.2, 2008-04-04
TDK5100F
Reference
Table 10
Supply Voltage VS=3V, Ambient temperature Tamb=25°C (cont’d)
Parameter
Symbol
Limit Values
min.
typ.
max.
Unit Test
Conditions
FSK Switch Output (Pin 4)
On resistance
RFSKOUT
250
Ω
VFSKDTA = 0 V
On capacitance
CFSKOUT
6
pF
VFSKDTA = 0 V
Off resistance
RFSKOUT 10
kΩ
VFSKDTA = VS
Off capacitance
CFSKOUT
1.5
pF
VFSKDTA = VS
5
pF
100
Ω
f = 13.56 MHz
µH
f = 13.56 MHz
Crystal Oscillator Input (Pin 5)
Load capacitance
CCOSCmax
Serial Resistance of
the crystal
Input inductance of the
COSC pin
4.6
ASK Modulation Data Input (Pin 6)
ASK Transmit disabled VASKDTA 0
0.5
ASK Transmit enabled VASKDTA 1.5
VS
V
Input bias current
ASKDTA
IASKDTA
30
µA
VASKDTA = VS
Input bias current
ASKDTA
IASKDTA
µA
VASKDTA = 0 V
ASK data rate
fASKDTA
-20
V
20
kHz
VFSKDTA 0
0.5
V
FSK Switch off
VFSKDTA 1.5
VS
V
Input bias current
FSKDTA
IFSKDTA
30
µA
VFSKDTA = VS
Input bias current
FSKDTA
IFSKDTA
µA
VFSKDTA = 0 V
FSK data rate
fFSKDTA
FSK Modulation Data Input (Pin 7)
FSK Switch on
-20
20
kHz
7.4
dBm
Power Amplifier Output (Pin 9)
Output Power2) at 434
MHz transformed to
50 Ohm
Data Sheet
POUT434
3.0
5.2
32
V 1.2, 2008-04-04
TDK5100F
Reference
Table 10
Supply Voltage VS=3V, Ambient temperature Tamb=25°C (cont’d)
Parameter
Symbol
Limit Values
min.
typ.
max.
Unit Test
Conditions
Power Down Mode Control (Pin 10)
Power Down mode
V PDWN
0
0.7
V
VASKDTA < 0.2 V
VFSKDTA < 0.2 V
PLL Enable mode
V PDWN
1.5
VS
V
VASKDTA < 0.5 V
Transmit mode
V PDWN
1.5
VS
V
VASKDTA > 1.5 V
Input bias current
PDWN
IPDWN
30
µA
VPDWN = VS
1) Derating linearly to a saturation voltage of max. 140 mV at ICLKOUT = 0 mA
2) Power amplifier in overcritical C-operation
Matching circuitry as used in the 50 Ohm-Output Testboard at the specified frequency.
Tolerances of the passive elements not taken into account.
4.3.2
AC/DC Characteristic at 2.1V ...4.0 V, -40°C ...+125°C
Table 11
Supply Voltage VS=2.1V ... 4.0V, Tamb=-40°C ... +125°C
Parameter
Symbol
Limit Values
min.
max.
Unit Test
Conditions
4
µA
3.5
4.6
mA
typ.
Current consumption
Power Down mode
IS PDWN
V (Pins 10, 6
and 7) < 0.2 V
PLL Enable mode
IS PLL_EN
Transmit mode
IS
7
10.2
mA
VS = 2.1 V
TRANSMIT
7.7
10.9
mA
VS = 3 V
8.1
11.4
mA
VS = 4 V
Output frequency
Output frequency1)
fOUT
434
MHz fOUT = 32 * fCOSC
Clock Driver Output (Pin 1)
Output current (High)
ICLKOUT
5
µA
VCLKOUT = VS
Saturation Voltage
(Low)2)
VSATL
0.5
V
ICLKOUT = 0.6
mA
Data Sheet
33
V 1.2, 2008-04-04
TDK5100F
Reference
Table 11
Supply Voltage VS=2.1V ... 4.0V, Tamb=-40°C ... +125°C (cont’d)
Parameter
Symbol
Limit Values
min.
typ.
max.
Unit Test
Conditions
FSK Switch Output (Pin 4)
On resistance
RFSKOUT
280
Ω
VFSKDTA = 0 V
On capacitance
CFSKOUT
6
pF
VFSKDTA = 0 V
Off resistance
RFSKOUT 10
kΩ
VFSKDTA = VS
Off capacitance
CFSKOUT
1.5
pF
VFSKDTA = VS
5
pF
100
Ω
f = 13.56 MHz
µH
f = 13.56 MHz
Crystal Oscillator Input (Pin 5)
Load capacitance
CCOSCmax
Serial Resistance of
the crystal
Input inductance of the
COSC pin
4.6
ASK Modulation Data Input (Pin 6)
ASK Transmit disabled VASKDTA 0
0.5
V
ASK Transmit enabled VASKDTA 1.5
VS
V
Input bias current
ASKDTA
IASKDTA
33
µA
VASKDTA = VS
Input bias current
ASKDTA
IASKDTA
µA
VASKDTA = 0 V
ASK data rate
fASKDTA
-20
20
kHz
VFSKDTA 0
0.5
V
FSK Switch off
VFSKDTA 1.5
VS
V
Input bias current
FSKDTA
IFSKDTA
33
µA
VFSKDTA = VS
Input bias current
FSKDTA
IFSKDTA
µA
VFSKDTA = 0 V
FSK data rate
fFSKDTA
FSK Modulation Data Input (Pin 7)
FSK Switch on
Data Sheet
-20
20
34
kHz
V 1.2, 2008-04-04
TDK5100F
Reference
Table 11
Supply Voltage VS=2.1V ... 4.0V, Tamb=-40°C ... +125°C (cont’d)
Parameter
Symbol
Limit Values
min.
typ.
max.
Unit Test
Conditions
Power Amplifier Output (Pin 9)
Output Power 3) at 434 POUT, 434 -0.8
MHz
POUT, 434 0.0
transformed to 50
POUT, 434 0.5
Ohm.
2.4
4.8
dBm VS = 2.1 V
5.2
7.7
dBm VS = 3.0 V
6.9
10.6
dBm VS = 4.0 V
Power Down Mode Control (Pin 10)
Power Down mode
V PDWN
0
0.5
V
VASKDTA < 0.2 V
VFSKDTA < 0.2 V
PLL Enable mode
V PDWN
1.5
VS
V
VASKDTA < 0.5 V
Transmit mode
V PDWN
1.5
VS
V
VASKDTA > 1.5 V
Input bias current
PDWN
IPDWN
38
µA
VPDWN = VS
1) a) When the minimum TA is increased by 5°C, the minimum fVCO decreases by 1 MHz.
b) When the maximum TA is decreased by 5°C, the maximum fVCO increases by 1 MHz.
c) When the minimum VS is increased by 25 mV, the maximum fVCO increases by 1 MHz.
Restriction of c): The maximum fVCO must not be increased by more than 40 MHz
by increasing VS.
All three measures can be taken independently and additive.
2) Derating linearly to a saturation voltage of max. 140 mV at ICLKOUT = 0 mA
3) Matching circuitry as used in the 50 Ohm-Output Testboard.
Tolerances of the passive elements not taken into account.
Range @ 2.1 V, +25°C: dBm +/- 2.0 dBm
Typ. temperature dependency at 2.1 V: + 0.4 dBm@-40°C and - 1.3 dBm@+125°C, reference +25°C
Range @ 3.0 V, +25°C: 5.0 dBm +/- 2.2 dBm
Typ. temperature dependency at 3.0 V: + 0.4 dBm@-40°C and - 2.4 dBm@+125°C, reference +25°C
Range @ 4.0 V, +25°C: dBm +/- 3.0 dBm
Typ. temperature dependency at 4.0 V: + 0.8 dBm@-40°C and - 3.3 dBm@+125°C, reference +25°C
Data Sheet
35
V 1.2, 2008-04-04
TDK5100F
Package Outlines
0.5
0.1 A
A
0.22 ±0.05
0.08
M
C
0.42 +0.15
-0.1
ABC
4.9
3 ±0.1
6 max.
+0.08
0.125 -0.05
3 ±0.1
H
0.09
0.85 ±0.1
1.1 max.
Package Outlines
0.15 max.
5
0.25
M
ABC
B
Index Marking
Figure 18
PG-TSSOP-10
You can find all of our packages, sorts of packing and others in our
Infineon Internet Page “Products”: http://www.infineon.com/products.
Dimensions in mm
SMD = Surface Mounted Device
Data Sheet
36
V 1.2, 2008-04-04
TDK5100F
List of Figures
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Data Sheet
Page
IC Pin Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Power mode control circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ASK Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
FSK Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Alternative ASK Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Alternative FSK Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
50 Ohm-output testboard schematic . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Top Side of TDK5100 F-Testboard with 50 Ohm-Output. . . . . . . . . . . 20
Bottom Side of TDK5100 F-Testboard with 50 Ohm-Output . . . . . . . . 20
Stripline-antenna testboard schematic. . . . . . . . . . . . . . . . . . . . . . . . . 22
Top Side of TDK5100 F-Testboard with Stripline-Antenna . . . . . . . . . 23
Bottom Side of TDK5100 F-Testboard with Stripline-Antenna. . . . . . . 23
Application Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
FSK Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Equivalent power amplifier tank circuit. . . . . . . . . . . . . . . . . . . . . . . . . 28
Output power Po (mW) and collector efficiency E vs. load resistor RL. 29
PG-TSSOP-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
37
V 1.2, 2008-04-04
TDK5100F
List of Tables
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Data Sheet
Page
Order Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Definition and Functions - Overview . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin Definition and Function1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
FSKDTA - FSK Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ASKDTA - Power Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Clock Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Absolute Maximum Ratings, Tamb = -40 °C … +125 °C . . . . . . . . . . . . 30
Operating Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Supply Voltage VS=3V, Ambient temperature Tamb=25°C . . . . . . . . . . 31
Supply Voltage VS=2.1V ... 4.0V, Tamb=-40°C ... +125°C. . . . . . . . . . . 33
38
V 1.2, 2008-04-04
w w w . i n f i n e o n . c o m
Published by Infineon Technologies AG