2 Post and 4 Post Rack Standoff Brackets S P E C I F I C AT I O N S H E E T specifications The 2 and 4 post standoff brackets shall be made of steel and will allow front offset mounting of 19" EIA horizontal managers, and equipment in a standard 2 or 4 post rack. The offset depths will be optimized to allow proper utilization of the PatchRunner ™ High Capacity Vertical Manager’s finger spacing in each of the available rack mounting positions for the vertical manager. Rack Standoff Brackets technical information Rack compatibility: All Panduit 2 or 4 post racks Rack standoff depth: RSB1A : 1.6" front offset for PatchRunner ™ High Capacity Vertical Cable Manager mounted in fully back extended position on rack RSB1B: 2.9" front offset for PatchRunner™ High Capacity Vertical Cable Manager mounted in standard mounting position on rack RSB1C: 5.3" front offset for PatchRunner™ High Capacity Vertical Cable Manager mounted in fully forward extended position on rack Installation: The standoff brackets are attached to both the left and right equipment rail at the same RU. Material: 16 gage steel, black powder coat finish key features and benefits Specifically designed for equipment and horizontal managers Positions equipment and horizontal managers at the proper depth with regard to the vertical manager fingers to allow maximum finger space utilization Designed to work with Panduit vertical cable managers Designed to work with the PatchRunner High Capacity Vertical Cable Managers at each of the available installation depths Improves aesthetics of the cable management system Positions doors of the vertical and horizontal managers at the same depth on the rack, increasing system aesthetics Through hole allow easy installation Through holes in brackets allow easy installation to rack without interfering with equipment above or below the bracket installation RU ™ applications Deep finger vertical managers require that horizontal managers and strain relief products are installed at the proper depth to be effective. Panduit rack standoff brackets for 2 and 4 post racks allows increased flexibility for rack and cable management systems by allowing proper front standoff positioning of equipment or horizontal managers and strain relief products. Three depths were designed to match the mounting locations of the 1.6" front offset: RSB1A 2.9" front offset: RSB1B 5.3" front offset: RSB1C PatchRunner ™ High Capacity Vertical Cable Managers Dual-sided 6" wide: PEV6* 8" wide: PEV8* 10" wide: PEV10* 12" wide: PEV12* Single-sided 6" wide: PEVF6* 8" wide: PEVF8* 10" wide: PEVF10 12" wide: PEVF12 Dual hinged doors 6" wide: PED6* 8" wide: PED8* 10" wide: PED10* 12" wide: PED12 NetManager ™ High Capacity Horizontal Cable Managers 19" front and rear 1 RU manager: 2 RU manager: 3 RU manager: 4 RU manager: 19" front only 1 RU manager: 2 RU manager: 3 RU manager: 4 RU manager: NM1 NM2 NM3 NM4 NMF1 NMF2 NMF3 NMF4 2 Post Racks 3" Channel racks #12-24 threaded rail, numbered up: 45 RU: 52 RU: 42 RU: 24 RU: 6" Channel rack #12-24 threaded rail, numbered up: 45 RU: 52 RU: R2P R2P96 R2P79 R2P48 R2P6S R2P6S96 4 Post Racks PatchRunner High Capacity Vertical Cable Manager and provide the proper rack standoff clearance for horizontal managers, equipment, and strain relief products. Other applications include using the standoff brackets in conjunction with 1, 2, 4, or 8 RU metal blanking panels as a way to protect power or communications cables that extend outside the rack. ™ 7' version 30" depth threaded rail #12-24: Cage nut rail: 7' version 23" depth threaded rail #12-24: Cage nut rail: 7' version 36" depth threaded rails #12-24: Cage nut rail: 7' version 42" depth threaded rails #12-24: Cage nut rail: R4P* R4PCN* R4P23* RP23CN R4P36* RP36CN* R4P42* R4P42CN* Rack Filler Panels 1 RU: 2 RU: 4 RU: 8 RU: w w w. p a n d u i t . c o m DPFP1 DPFP2 DPFP4 DPFP8 *Add suffix 96 to the end of the part number for 8' Part Numbers. 2 Post and 4 Post Rack Standoff Brackets applications Used in conjunction with a 1, 2, 4, or 8 RU rack filler panel, the standoff brackets can be used to create a barrier to protect protruding power cords or cables. Used to position horizontal cable managers at the proper depth, the standoff brackets provide the proper rack standoff clearance for the horizontal cable managers. RSB1A: 1 RU Rack Standoff Bracket 1.6"D from Rack 1.7 [44] 0.8 [20] 1.6 [41] RSB1B: 1 RU Rack Standoff Bracket 2.9"D from Rack 1.7 [44] 0.8 [20] 2.9 [74] RSB1C: 1 RU Rack Standoff Bracket 5.3"D from Rack 1.7 [44] 0.8 [20] 5.3 [135] Dimensions are in inches. [Dimensions in brackets are metric] WORLDWIDE SUBSIDIARIES AND SALES OFFICES PANDUIT CANADA Markham, Ontario [email protected] Phone: 800.777.3300 PANDUIT EUROPE LTD. London, UK [email protected] Phone: 44.20.8601.7200 PANDUIT SINGAPORE PTE. LTD. Republic of Singapore [email protected] Phone: 65.6305.7575 PANDUIT JAPAN Tokyo, Japan [email protected] Phone: 81.3.6863.6000 PANDUIT LATIN AMERICA Guadalajara, Mexico [email protected] Phone: 52.33.3777.6000 PANDUIT AUSTRALIA PTY. LTD. Victoria, Australia [email protected] Phone: 61.3.9794.9020 For a copy of Panduit product warranties, log on to www.panduit.com/warranty For more information Visit us at www.panduit.com Contact Customer Service by email: [email protected] or by phone: 800.777.3300 ©2012 Panduit Corp. ALL RIGHTS RESERVED. RKSP121--WW-ENG Replaces WW-RKSP85 1/2013