MIC95410 Evaluation Board 6.6mΩ RDS(ON), 7A, 5.5VIN Load Switch in 1.2mm x 2.0mm QFN Package General Description The MIC95410 is a high-side load switch used for computing and for ultra-dense embedded computing boards where high-current, low-voltage rails from sub-1V to 5.5V have to be sectioned. The integrated 6.6mΩ RDS(ON) N-channel MOSFET ensures low voltage drop and low power dissipation while delivering up to 7A of load current. The MIC95410 provides user-adjustable slew-ratecontrolled turn-on to limit the inrush current to the input supply voltage. The MIC95410 is available in thermally efficient, spacesaving 10-pin 1.2mm × 2.0mm QFN package with 0.5mm pin pitch and an operating junction temperature range from –40°C to +125°C. The basic parameters of the MIC95410 evaluation board are the IN supply of 1V to 5.5V and the separated bias voltage from 2.7V to 9V. It also includes a TTL-logic level turn-on command (CTL) and an output discharge function when disabled. Due to the optimized pinout of the MIC95410, the evaluation board can achieve a two-layer-only routing (top and bottom), while internal planes are connected to GND and kept as solid GND planes for best thermal performance. See PCB Layout section. MIC95410 datasheet and support documentation are available on Micrel’s web site at: www.micrel.com. Ordering Information Part Number Description MIC95410YFL EV MIC95410 Evaluation Board Evaluation Board Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com October 1, 2014 Revision 1.0 Micrel, Inc. MIC95410 Evaluation Board Getting Started Recommended Setup The MIC95410 evaluation board setup comprises of the following points: • Recommended Steps 1. Ensure no jumper is installed at J1. R1 will pull down the CTL pin and keep the MIC95410 disabled until Step 8. A power supply with at least 7A of current capability for IN, not to exceed 5.5V. • A passive or active load which can handle up to 7A at 5.5V, connected at OUT (CON3) / GND (CON4). • A low-power bias supply for VS, 2.7V ≤ VVS ≤ 9V. • A function generator for driving CTL. • A digital multi-meter (DMM). 2. Connect the VS supply. Connect the VS bias supply to terminals J2-2 (VS)/J21 (GND). J2 is the connector at the bottom edge of the evaluation board. Alternatively, VS can be shorted to IN by installing a jumper across positions J2-3 (IN) and J2-2 (VS). This is possible only for 2.7V ≤ VIN ≤ 5.5V. If VIN is lower than 2.7V, an external independent bias supply for VS is mandatory. The bias supply pin VS can be shorted to IN by means of the VS header located at the bottom of the board near the label. In this case, evaluation can be performed for 2.7V ≤ VIN ≤ 5.5V, and the low-power bias supply for VS can be avoided. Similarly, the CTL pin can be shorted to VS by means of header J1, making the function generator redundant. 3. Connect the IN supply. Connect the power supply to the IN (CON1) and GND (CON2) terminals and regulate its current limit to approximately 7.5A. An ammeter may be placed between the input supply and the IN terminal to the evaluation board. Ensure that the supply voltage is monitored at the IN terminal (CON1 or J5), because the ammeter and/or power lead resistance can reduce the voltage supplied to the input. Keep the power supply disabled; do not apply power until Step 7. Power-Up Precautions The evaluation board does not have reverse polarity protection. Applying a negative voltage to the IN or VS terminals may damage the device. 4. Connect the load to the output terminals. Connect the load across the terminals OUT (CON3)/GND (CON4). Adjust the load. Do not exceed a 7A current. Output voltage may be monitored at J4. The turn-on of the MIC95410, especially in the presence of large output capacitive loads associated with long input leads, may cause some L-C ringing. The ringing may cause false current readings and generate voltage overshoot. Reducing the length of the input leads as much as possible (10cm or less) or using a large electrolytic decoupling capacitor (up to some mF) between IN (CON1) and GND (CON2) of the evaluation board is recommended. 5. Connect the DMM across the MIC95410. Set the DMM to a mV voltage reading and connect it between J6-1 (IN_S, positive terminal) and J6-2 (OUT_S, negative terminal). This is for reading the voltage drop across the MIC95410. 6. Connect the function generator to CTL. Connect the function generator between J1-2 (CTL) and J1-1 (GND). Set it to DC mode with the level between 2.4V and VVS (unterminated). Keep the output disabled. 7. Enable the IN and VS supplies. 8. Enable the MIC95410. Enable the MIC95410 by enabling the function generator output. Alternatively, install a jumper across J1-2 (CTL) and J1-3 (VS). Verify that the input voltage passes to the output and monitor the voltage drop across the MIC95410 with the DMM. October 1, 2014 2 Revision 1.0 Micrel, Inc. MIC95410 Evaluation Board Evaluation Board Description J1 - CTL (Control) Input The MIC95410 can be turned ON or OFF by setting a TTL high logic level to pin CTL (J1-2). Pin J1-2 is pulled to GND through R1, such that CTL is not left floating. J4 - OUT J4 can be used to monitor the output voltage. The MIC95410 output capacitance can be increased by installing a 0603 ceramic capacitor in position C3A. CTL can be driven either at DC (static) or by a square wave signal. For square wave drive, ensure the frequency of the signal is low enough to limit the turn-on/turn-off power dissipation within safe limits. Also depending on the load, frequencies of 1Hz or lower are recommended. Note, this is a two-pin header with one pin connected to a power supply voltage and the other pin connected to GND. Never install a jumper on this header because it will short the power supply to GND. For static drive, installing/removing a jumper across positions J2-2 (CTL) and J2-3 (VS) is adequate. J5 - IN J5 can be used to monitor the input voltage. The MIC95410 input capacitance can be increased by installing a 0603 ceramic capacitor in position C2A. J2 - VS Supply The MIC95410 has a separate bias pin (VS) for powering the charge pump (2.7V ≤ VVS ≤ 9V). The bias power supply should be connected at J2-2 (VS)/J2-1 (GND). Alternatively, VS can be shorted to IN by installing a jumper across positions J2-3 (IN) and J2-2 (VS). This is possible only for 2.7V ≤ VIN ≤ 5.5V. Note that this is a two-pin header with one pin connected to a power supply voltage and the other pin connected to GND. Never install a jumper on this header because it will short the power supply to GND. J6 – Voltage Drop Sensing J6 can be used to monitor the voltage drop across the MIC95410. J3 - GC GC (gate connection of power MOSFET switch) can be monitored at J3. Because the current sourcing capability of GC is limited, ensure that the impedance of the monitoring input does not cause excessive loading. Please note that the solder joints and some unavoidable copper trace distance also add up to the RDS(ON) of the MIC95410 and, therefore, the measured resistive drop is slightly larger than the pure intrinsic RDS(ON) contribution. Install a capacitor in position C4 to adjust the turn-on speed/inrush current. J7 – Capacitive LOAD To emulate the effect of large load capacitors at the output side of the MIC95410, it is possible to install a capacitor in position C3B. J7 can be used to connect/disconnect C3B. October 1, 2014 3 Revision 1.0 Micrel, Inc. MIC95410 Evaluation Board Evaluation Board Schematic October 1, 2014 4 Revision 1.0 Micrel, Inc. MIC95410 Evaluation Board Bill of Materials Item Part Number C1 GRM188R61C475KE11 C2 GRM155R61C105MA12 C3 GRM155R61H104ME14 Manufacturer Description (1) Murata Qty. Capacitor, ceramic, X5R, 4.7uF 16V 10%, Size 0603. 1 Murata Capacitor, ceramic, X5R, 1uF 16V 20%, Size 0402. 1 Murata Capacitor, ceramic, X5R, 100nF 50V 20%, Size 0402. 1 C1A ANY Not Installed, Size 0402. C4 C2A C3A ANY Not Installed, Size 0603. C3B ANY Not installed, Size EIA-3528. Resistor, 100kΩ 5%, Size 0603. 1 6.6mΩ RDS(ON), 7A, 5.5VIN Load Switch in 1.2mm × 2.0mm QFN Package. 1 R1 RC0603-104J ANY U1 MIC95410YFL Micrel, Inc.(2) Notes: 1. Murata: www.murata.com. 2. Micrel, Inc.: www.micrel.com. October 1, 2014 5 Revision 1.0 Micrel, Inc. MIC95410 Evaluation Board PCB Layout Top Layer (Routing) Mid Layer 1 (GND plane) October 1, 2014 6 Revision 1.0 Micrel, Inc. MIC95410 Evaluation Board PCB Layout (Continued) Mid Layer 2 (GND plane) Bottom Layer (Routing) – Top View October 1, 2014 7 Revision 1.0 Micrel, Inc. MIC95410 Evaluation Board MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company’s products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2014 Micrel, Incorporated. October 1, 2014 8 Revision 1.0