Package Outline Drawing L23.15x15 23 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (PUNCH QFN) Rev 3, 10/10 A 3.22 1 2.2 0.2 H AB 1.02 23 22 21 20 20 21 22 0.05 M H AB 19 6 7 8 9 10 11 9.9 13.8 4.7 4.26 2.36 1.34 18 3.4 4.38 X4 17 0.8 2.28 16 0.2 H AB 17 15.0±0.2 3.4 18 15.0±0.2 15.8±0.2 16 1 2 4.7 19 35x 0.5 0.82 4.8 (35x 0.40) 15.8±0.2 7x 1.9 ±0.05 23 18x 0.75 3 4 B 5 6 7 8 10x 1.1 ±0.1 9 10 11 15 11x 0.7 0.90 14 13 12 2.0 5.82 11x 1.85 ±0.05 7x 0.8 TOP VIEW BOTTOM VIEW 8° ALL AROUND 2.2 ±0.2 NOTES: S 0.2 S SIDE VIEW 0.25 S 0.05 1. Dimensions are in millimeters. 2. Unless otherwise specified, tolerance : Decimal ± 0.2; Body Tolerance ±0.2mm 3. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. Plastic Packages for Integrated Circuits 1 2 3 4 5 12 13 14 15 18x 1.3 ±0.1 X4 3x 2.6 5.18 4.73 4.68 4.03 4.08 3.63 8.15 3.58 2.93 6.88 2.98 5.58 2.48 23 1 0.00 0.00 4.13 2.13 2.83 3.43 0.83 1.53 1.07 0.00 1.77 2.37 3.07 3.67 0.32 0.77 3.02 1.47 3.52 1.92 4.64 4.13 6.03 6.73 6.78 8.09 3.43 2.83 6.11 5.67 4.97 4.37 3.67 3.07 2.37 1.77 1.07 0.60 6.48 4.88 5.68 0.93 2.75 3.05 4.03 4.83 6.88 8.14 5.53 5.03 2.08 1.58 0.78 0.18 1.82 0.65 0.00 4.12 4.72 5.22 5.82 6.07 2.32 4.07 4.77 5.17 5.87 6.02 3.12 3.02 3.62 3.62 8.15 3.67 2.13 5.62 2.97 2.92 3.62 4.22 4.92 5.52 6.82 8.10 2.52 0.00 2.57 1.48 1.87 0.88 1.47 STENCIL PATTERN WITH SQUARE PADS-1 TYPICAL RECOMMENDED LAND PATTERN 6.73 6.23 4.18 4.68 4.38 3.88 1.83 2.33 1.53 1.53 0.00 0.52 0.82 2.87 3.17 4.69 4.99 6.52 0.00 0.52 0.82 2.82 3.67 6.48 4.58 4.28 2.23 1.48 0.88 0.13 0.00 0.60 5.50 5.80 6.52 STENCIL PATTERN WITH SQUARE PADS-2 Plastic Packages for Integrated Circuits 0.37 0.77 0.78 0.28 0.13 0.00 1.68 0.00 0.33 4.42 4.37 1.38 2.18 4.92 2 8.10 6.48 5.48 4.88 4.18 3.58 2.88 2.28 1.58 0.98 0.28 0.00 0.32 1.02 1.62 2.32 1.88 1.43 0.73 6.06 5.72 4.97 5.78 5.13 2.53 1.83 5.72 6.03 8.14 6.88 4.68 4.18 0.78 1.02 0.00 1.82 2.32 3.12 3.62 4.42 4.92 5.83 5.72 5.98