NEC Express5800/R120d-2M Configuration Guide Introduction This document contains product and configuration information that will enable you to configure your system. The guide will ensure fast and proper configuration of your NEC Express5800 server. July 17, 2013 Revision 7.0 NEC Corporation CONFIGURATION GUIDE – NEC Express5800/R120d-2M Contents TECHNICAL SPECIFICATION ........................................................................................ 3 Key Features .......................................................................................................................................... 3 Specification .......................................................................................................................................... 3 EXTERNAL VIEWS ......................................................................................................... 8 Front and Rear Views ........................................................................................................................... 8 Dimensions (mm) ................................................................................................................................ 10 CONFIGURATION DIAGRAM ....................................................................................... 11 Expansion Slots .................................................................................................................................. 11 SERVER CONFIGURATION ......................................................................................... 12 1 2 3 4 5 6 7 8 9 Base Models ................................................................................................................................. 12 Processors and Heat Sink .......................................................................................................... 12 Memory ......................................................................................................................................... 13 3.1 Memory Configuration........................................................................................................ 13 Internal Hard Disk Drives ............................................................................................................ 17 4.1 RAID Configuration ............................................................................................................ 17 4.2 Internal Drive Configuration ............................................................................................... 18 Optical Drive ................................................................................................................................. 27 Internal Tape / RDX Drives .......................................................................................................... 27 6.1 Tape / RDX Drive Selection ............................................................................................... 28 6.2 Tape / RDX Configuration .................................................................................................. 28 PCI Riser Card / PCI Card ........................................................................................................... 29 7.1 PCI Riser Card ................................................................................................................... 29 7.2 Full Length PCI Card installation Kit .................................................................................. 29 7.3 Graphics Card Installation Kit ............................................................................................ 29 7.4 Network Interface Controller .............................................................................................. 30 7.5 External Storage Controller ............................................................................................... 32 7.6 Serial Port Adapter ............................................................................................................. 32 Other Add-in Components .......................................................................................................... 33 8.1 Power Supply Module ........................................................................................................ 33 8.2 Redundant Fan Kit ............................................................................................................. 33 8.3 Trusted Platform Module Kit .............................................................................................. 33 8.4 Internal Flash Memory ....................................................................................................... 33 8.5 Flash FDD .......................................................................................................................... 34 8.6 Front Bezel ......................................................................................................................... 34 Add-on Components ................................................................................................................... 34 9.1 17-inch LCD Console Drawer ............................................................................................ 34 9.2 KVM Switch ........................................................................................................................ 35 9.3 Cable Management Arm .................................................................................................... 35 9.4 Server Management License ............................................................................................. 35 9.5 Medium and Cartridge ....................................................................................................... 35 REFERENCES............................................................................................................... 36 Server Management ............................................................................................................................ 36 OS Support Matrix for PCI Cards and Embedded Controllers ....................................................... 37 Supporting PCI Cards and Installable Slots ..................................................................................... 37 Copyright Notice and Liability Disclaimer ........................................................................................ 41 REVISION HISTORY ..................................................................................................... 42 NEC Corporation Revision 7.0 – July 17, 2013 2 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Technical Specification Key Features High performance with the latest Intel® Xeon® processor E5-2600 product family Up to 768 GB of high speed DDR3-1333 memory High energy efficiency with power capping feature and 80 PLUS® Platinum power supply Full manageability by integrated EXPRESSSCOPE Engine 3 Specification (1 / 2) Model Part Number Processor R120d-2M Type Clock speed Number of Processors Cache Cores and Threads Chipset Memory Type Standard Capacity Maximum Capacity Memory protection Internal Storage Standard Capacity Maximum Capacity Disk Controller RAID Expansion Slots NEC Corporation Hot Plug Optical Disk Drive Optical Drive Bays 3.5-inch Media Bays Disk Drive Bays Standard N8100-1793F Intel® Intel® Intel® Intel® Intel® Xeon® Xeon® Xeon® Xeon® Xeon® processor processor processor processor processor E5-2609 E5-2620 E5-2630L E5-2640 E5-2643 2.40 GHz 2 GHz 2 GHz 2.50 GHz 3.30 GHz 1 to 2 10 MB 15 MB 10 MB 4C-4T 6C-12T 4C-8T Intel® C602-J Chipset DDR3-1333 ECC Unbuffered Low Power DIMM, DDR3-1600 ECC Registered Low Power DIMM, DDR3-1333 ECC Load Reduced DIMM 0 GB 768 GB (24 x 32 GB) ECC, x4 SDDC, Memory Mirroring, Memory Lockstep, Memory Sparing 0 GB SAS HDD : 19.2 TB (16 x 1.2 TB) SATA HDD : 16 TB (16 x 1 TB) SAS SSD : 6.4 TB ( 16 x 400 GB) SATA : 6 Gb/s (Integrated) SAS: 6 Gb/s (Optional) SATA : RAID 0/1/5/6/10/50/60 (Optional) SAS : RAID 0/1/5/6/10/50/60 (Optional) Supported Optional 1 1 1 16 Total: 7 slots available 2 PCIe 3.0 x8 (x16 connector) 2 PCIe 3.0 x4 (x8 connector) 2 1 PCIe 3.0 x8 (x16 connector) 1 PCIe 3.0 x8 (x8 connector) dedicated LAN slot 1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot Revision 7.0 – July 17, 2013 3 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Model Expansion Slots (Cont.) R120d-2M Optional Riser Card (N8116-25) Optional Riser Card (N8116-26) Optional Riser Card (N8116-27) Video Controller (VRAM) Resolution / Color Interfaces Server Management Redundant Fan Redundant Power Supply Power Supply Power Consumption (Max. Config, Idling) (Max. Config, Operating) Acoustical Noise Max. Config, Idling (Sound Pressure Max. Config, Operating 4 Level) Dimensions (W x D x H ) Weight (Minimum / Maximum) Temperature, Relative Humidity (non-condensing) Regulatory and Safety Operating Systems NEC Corporation Total: 6 slots available 1 PCIe 3.0 x16 (x16 connector) 2 PCIe 3.0 x4 (x8 connector) 2 1 PCIe 3.0 x8 (x16 connector) 1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot 1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot Total: 7 slots available 1 PCIe 3.0 x8 (x16 connector) 2 PCIe 3.0 x4 (x8 connector) 2 1 PCIe 3.0 x8 (x16 connector) 1 64-bit/ 133 MHz PCI-X 1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot 1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot Total: 7 slots available 2 1 PCIe 3.0 x8 (x16 connector) 2 PCIe 3.0 x4 (x8 connector) 2 64-bit / 33 MHz 5V PCI 1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot 1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot Integrated in Server Management Controller (32MB) 3 1280 x 1024 / 16.7M 2 x VGA (15-pin mini D-sub, 1 x front, 1 x rear) 1 to 2 Serial (9-pin mini D-sub, RS232-C, 1 to 2rear) 9 x USB2.0 (2 x front, 4 x rear, 3 x internal) 2 x 1000BASE-T LAN connector (RJ-45, 2 x rear) 1 x Management LAN connector (RJ-45, 1 x rear) EXPRESSSCOPE Engine 3 Optional, hot plug Optional, hot plug 1 to 2 x 450 Watt or 800 Watt or 1000 Watt 80 PLUS® Platinum certified hot plug PSU 100-240 VAC ± 10% 50 / 60 Hz ± 3 Hz 353 VA / 357 VA / 359 VA / 363 VA / 354 VA / 348 Watt 353Watt 354 Watt 357 Watt 349 Watt 653 VA / 740 VA / 708 VA / 810 VA / 792 VA / 646 Watt 733 Watt 701 Watt 803 Watt 783 Watt 49.3dB 49.4dB 49.3dB 49.3dB 56.4dB 53.6dB 56.4dB 57.6dB 5 5 448.0 x 735.8 x 87.2 mm / 17.6 x 28.9 x 3.4 in (2U) 20.5 kg / 33 kg, 45.19 lbs. / 72.75 lbs. 6 6 Operating: 10° to 40° C / 50° to 104° F, 20 to 80% Non-Operating: -10° to 55° C / 14° to 131° F, 20 to 80% FCC, C-TICK, CE, UL, CB, RoHS, WEEE, CCC, BSMI, KC Microsoft® Windows Server® 2003 R2, Standard Edition Microsoft® Windows Server® 2003 R2, Enterprise Edition Microsoft® Windows Server® 2003 R2, Standard x64 Edition Microsoft® Windows Server® 2003 R2, Enterprise x64 Edition Microsoft® Windows Server® 2008 Standard Microsoft® Windows Server® 2008 Enterprise Microsoft® Windows Server® 2008 Standard (x64) Microsoft® Windows Server® 2008 Enterprise (x64) Microsoft® Windows Server® 2008 R2 Standard Microsoft® Windows Server® 2008 R2 Enterprise 7 Microsoft® Windows Server® 2012 Standard 7 Microsoft® Windows Server® 2012 Datacenter 8 Red Hat Enterprise Linux 5.7 or later (x86) 8 Red Hat Enterprise Linux 5.7 or later (EM64T) Revision 7.0 – July 17, 2013 4 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Model R120d-2M Operating Systems Red Hat Enterprise Linux 6.1 or later (x86) 8 Red Hat Enterprise Linux 6.1 or later (x86_64) VMware ESX™ 4.1 Update 2 VMware ESX™i 5.0 Update 1 VMware ESX™i 5.1 1 2 3 4 5 6 7 8 8 An optional drive cage is required to install more than 8 hard drives. Available only when the second processor is configured. Maximum resolution available via EXPRESSSCOPE Engine 3 remote console is 1280 x 1024 / 65K colors. Noise emission was measured in accordance with ISO 7779. The actual value may vary by the operating environment. When mounting 1000 Watt power supply, the depth is 770 mm (30.31 in). Operable up to 35°C (95°F) when Xeon processor E5-2643 is configured with an added optional drive cage. For Windows Server 2012 installation, download the driver kit from the following website and install it after OS installation http://www.nec.com/en/global/prod/express/download/ For Linux support, contact our sales representative or go to the NEC website at: http://www.nec.com/global/prod/express/linux/index.html (2 / 2) Model Part Number Processor R120d-2M Type Clock speed Number of Processors Cache Cores and Threads Chipset Memory Type Standard Capacity Maximum Capacity Memory protection Internal Storage Standard Capacity Maximum Capacity Disk Controller RAID Expansion Slots NEC Corporation Hot Plug Optical Disk Drive Optical Drive Bays 3.5-inch Media Bays Disk Drive Bays Standard N8100-1793F Intel® Xeon® Intel® Xeon® Intel® Xeon® Intel® Xeon® processor processor processor processor E5-2650 E5-2650L E5-2670 E5-2690 2 GHz 1.80 GHz 2.60 GHz 2.90 GHz 1 to 2 20 MB 20 MB 20 MB 20 MB 8C-16T 8C-16T 8C-16T 8C-16T Intel® C602-J Chipset DDR3-1333 ECC Unbuffered Low Power DIMM, DDR3-1600 ECC Registered Low Power DIMM, DDR3-1333 ECC Load Reduced DIMM 0 GB 768 GB (24 x 32 GB) ECC, x4 SDDC, Memory Mirroring, Memory Lockstep, Memory Sparing 0 GB SAS HDD : 19.2 TB (16 x 1.2 TB) SATA HDD : 16 TB (16 x 1 TB) SAS SSD : 6.4 TB ( 16 x 400 GB) SATA : 6 Gb/s (Integrated) SAS: 6 Gb/s (Optional) SATA : RAID 0/1/5/6/10/50/60 (Optional) SAS : RAID 0/1/5/6/10/50/60 (Optional) Supported Optional 1 1 1 16 Total: 7 slots available 2 PCIe 3.0 x8 (x16 connector) 2 PCIe 3.0 x4 (x8 connector) 2 1 PCIe 3.0 x8 (x16 connector) 1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot 1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot Revision 7.0 – July 17, 2013 5 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Model Expansion Slots (Cont.) R120d-2M Optional Riser Card (N8116-25) Optional Riser Card (N8116-26) Optional Riser Card (N8116-27) Video Controller (VRAM) Resolution / Color Interfaces Server Management Redundant Fan Redundant Power Supply Power Supply Power Consumption (Max. Config, Idling) (Max. Config, Operating) Acoustical Noise Max. Config, Idling (Sound Pressure Max. Config, Operating 4 Level) Dimensions (W x D x H ) Weight (Minimum / Maximum) Temperature, Relative Humidity (non-condensing) Regulatory and Safety Operating Systems NEC Corporation Total: 6 slots available 1 PCIe 3.0 x16 (x16 connector) 2 PCIe 3.0 x4 (x8 connector) 2 1 PCIe 3.0 x8 (x16 connector) 1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot 1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot Total: 7 slots available 1 PCIe 3.0 x8 (x16 connector) 2 PCIe 3.0 x4 (x8 connector) 2 1 PCIe 3.0 x8 (x16 connector) 1 64-bit/ 133 MHz PCI-X 1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot 1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot Total: 7 slots available 2 1 PCIe 3.0 x8 (x16 connector) 2 PCIe 3.0 x4 (x8 connector) 2 64-bit / 33 MHz 5V PCI 1 PCIe 3.0 x8 (x8 connector) flexible integrated NIC slot 1 PCIe 3.0 x8 (x8 connector) dedicated RAID slot Integrated in Server Management Controller (32MB) 3 1280 x 1024 / 16.7M 2 x VGA (15-pin mini D-sub, 1 x front, 1 x rear) 1 to 2 Serial (9-pin mini D-sub, RS232-C, 1 to 2rear) 9 x USB2.0 (2 x front, 4 x rear, 3 x internal) 2 x 1000BASE-T LAN connector (RJ-45, 2 x rear) 1 x Management LAN connector (RJ-45, 1 x rear) EXPRESSSCOPE Engine 3 Optional, hot plug Optional, hot plug 1 to 2 x 450 Watt or 800 Watt or 1000 Watt 80 PLUS® Platinum certified hot plug PSU 100-240 VAC ± 10% 50 / 60 Hz ± 3 Hz 361 VA / 356 VA / 359 VA / 360 VA / 356 Watt 351 Watt 354 Watt 355 Watt 810 VA / 730 VA / 882 VA / 959 VA / 803 Watt 723 Watt 873 Watt 949 Watt 49.3dB 49.4dB 49.3dB 49.3dB 56.4dB 53.6dB 56.4dB 57.6dB 5 5 448.0 x 735.8 x 87.2 mm / 17.6 x 28.9 x 3.4 in (2U) 20.5 kg / 33 kg, 45.19 lbs. / 72.75 lbs. 6 6 Operating: 10° to 40° C / 50° to 104° F, 20 to 80% Non-Operating: -10° to 55° C / 14° to 131° F, 20 to 80% FCC, C-TICK, CE, UL, CB, RoHS, WEEE, CCC, BSMI, KC Microsoft® Windows Server® 2003 R2, Standard Edition Microsoft® Windows Server® 2003 R2, Enterprise Edition Microsoft® Windows Server® 2003 R2, Standard x64 Edition Microsoft® Windows Server® 2003 R2, Enterprise x64 Edition Microsoft® Windows Server® 2008 Standard Microsoft® Windows Server® 2008 Enterprise Microsoft® Windows Server® 2008 Standard (x64) Microsoft® Windows Server® 2008 Enterprise (x64) Microsoft® Windows Server® 2008 R2 Standard Microsoft® Windows Server® 2008 R2 Enterprise 7 Microsoft® Windows Server® 2012 Standard 7 Microsoft® Windows Server® 2012 Datacenter 8 Red Hat Enterprise Linux 5.7 or later (x86) 8 Red Hat Enterprise Linux 5.7 or later (EM64T) Revision 7.0 – July 17, 2013 6 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Model R120d-2M Operating Systems Red Hat Enterprise Linux 6.1 or later (x86) 8 Red Hat Enterprise Linux 6.1 or later (x86_64) VMware ESX™ 4.1 Update 2 VMware ESX™i 5.0 Update 1 VMware ESX™i 5.1 1 2 3 4 5 6 7 8 8 An optional drive cage is required to install more than 8 hard drives. Available only when the second processor is configured. Maximum resolution available via EXPRESSSCOPE Engine 3 remote console is 1280 x 1024 / 65K colors. Noise emission was measured at the bystander positions in accordance with ISO 7779. The actual value may vary by the operating environment. When mounting 1000 Watt power supply, the depth is 770 mm (30.31 in). Operable up to 35°C (95°F) when Xeon processor E5-2690 is configured with an added optional drive cage. For Windows Server 2012 installation, download the driver kit from the following website and install it after OS installation http://www.nec.com/en/global/prod/express/download/ For Linux support, contact our sales representative or go to the NEC website at: http://www.nec.com/global/prod/express/linux/index.html NEC Corporation Revision 7.0 – July 17, 2013 7 CONFIGURATION GUIDE – NEC Express5800/R120d-2M External Views Front and Rear Views Front View C A D F H JK L M N O B EG I P Q R Legend A. B. C. D. E. F. G. H. I. 2.5-inch Drive Bays 2.5-inch Drive Cage Bay USB Connectors Data LAN 1 Activity LED Data LAN 2 Activity LED Data LAN 3 Activity LED Data LAN 4 Activity LED Hard Drive Activity LED System Status LED NEC Corporation J. K. L. M. N. O. P. Q. R. BMC Reset Button Dump (NMI) Button System Reset Button UID LED Button Power Button / Power LED VGA Connector Media Bay Optical Drive Bay Pull-out Tab Revision 7.0 – July 17, 2013 8 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Rear View A C D E F G H I B J K LM N O Legend A. B. C. D. E. F. G. H. PCI Slots (Full-Height) PCI Slots (Low-Profile) Power Supply AC Inlet AC Power LED USB Connectors Data LAN Connectors Management LAN Connector NEC Corporation I. J. K. L. M. N. O. Serial Port Connector VGA Connector Dump (NMI) Switch UID Button/LED DC Power LED PCI Slot (LAN Riser) Additional Power Supply Slot Revision 7.0 – July 17, 2013 9 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Dimensions (mm) 450 Watt or 800 Watt Power Supply Configuration 869.9 735.8 87.2 482.0 448.0 35.0 88.0 482.0 87.4 831.9 * 1000 Watt Power Supply Configuration 869.9 735.8 87.2 482.0 88.0 482.0 87.4 831.9 * 770.0 448.0 35.0 * Wthout back side parts of slide rails (in that case, cable arm cannot be attached) NEC Corporation Revision 7.0 – July 17, 2013 10 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Configuration Diagram CHASSIS REAR 2.5-inch Drive Cage LAN Processor #1 6 DIMM Slots PCIe 3.0 PCI Riser PCIe 3.0 RAID Slot 6 DIMM Slots Hot plug Power Supply #1 Cooling Fan Processor #2 Minimum required components Hot plug Power Supply #1 2 DIMM Slots 6 DIMM Slots 4 RAID BBU Slots Cooling Fan Optical Drive Bay Media Bay Optical Drive Bay / Media Bay Legend: LAN Slot Redundant Cooling Fan 8 2.5-inch Drives 2.5-inch Drive Cage Hot plug Power Supply #2 #3C #2C #1C 8 2.5-inch Drives 6 DIMM Slots Hot plug Power Supply #2 CHASSIS TOP #2B #1B CHASSIS FRONT Standard components Expansion Slots #2B #3C #1B #2C #1C #1D #1A Legend Common #1A PCIe 3.0 x8, x8 connector, for a dedicated RAID controller #1C PCIe 3.0 x4, x8 connector, Low-profile, up to 220 mm length #2C PCIe 3.0 x4, x8 connector, Low-profile, up to 220 mm length #3C PCIe 3.0 x8, x16 connector, Full-height, up 220 mm length #1D PCIe 3.0 x8, x8 connector, for a flexible integrated NIC (LAN Riser) #1B PCIe 3.0 x8, x16 connector, Full-height, up to 220 mm length #2B PCIe 3.0 x8, x16 connector, Full-height, up to 312 mm length PCIe x16 Riser Card Kit #1B PCIe 3.0 x16, x16 connector, Full-height, up to 220 mm length #2B Not available PCI-X Riser Card Kit #1B PCIe 3.0 x8, x16 connector, Full-height, up to 220 mm length #2B 64bit / 133 MHz / 3.3V PCI-X, Full-height, up to 312 mm length PCI Riser Card Kit #1B 64bit / 33 MHz / 5V PCI, Full-height, up to 220 mm length #2B 64bit / 33 MHz / 5V PCI, Full-height, up to 312 mm length PCIe Riser Card Kit NOTE: Up to 312 mm length card can be installed into slot #1B when N8116-28 Full Length PCI Card installation Kit is installed. The slot #3C is available in dual processor configuration. NEC Corporation Revision 7.0 – July 17, 2013 11 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Server Configuration 1 Base Models Product Name / Description Part Number NEC Express5800/R120d-2M Server no processor, no RAM, no HDD, no ODD, no PSU, no front bezel Including: 2.5-inch Drive Cage, EXPRESSBUILDER DVD N8100-1793F NOTE: The base model must be ordered with a processor kit. 2 Processors and Heat Sink Available sockets: 2 Product Name / Description Part Number Processors 1 Processor Required Xeon E5-2609 Processor Kit Intel® Xeon ® Processor E5-2609 (2.40 GHz, 4C/4T, 10 MB) Xeon E5-2620 Processor Kit Intel® Xeon ® Processor E5-2620 (2 GHz, 6C/12T, 15 MB) Xeon E5-2630L Processor Kit Intel® Xeon ® Processor E5-2630L (2 GHz, 6C/12T, 15 MB) Xeon E5-2640 Processor Kit Intel® Xeon ® Processor E5-2640 (2.40 GHz, 6C/12T, 15 MB) Xeon E5-2643 Processor Kit Intel® Xeon ® Processor E5-2643 (3.30 GHz, 4C/8T, 10 MB) Xeon E5-2650 Processor Kit Intel® Xeon ® Processor E5-2650 (2 GHz, 8C/16T, 20 MB) Xeon E5-2650L Processor Kit Intel® Xeon ® Processor E5-2650L (1.80 GHz, 8C/16T, 20 MB) Xeon E5-2670 Processor Kit Intel® Xeon ® Processor E5-2670 (2.60 GHz, 8C/16T, 20 MB) Xeon E5-2690 Processor Kit Intel® Xeon ® Processor E5-2690 (2.90 GHz, 8C/16T, 20 MB) Processor Heat Sink st For 1 Processor N8101-545F Processor Heat Sink nd For 2 Processor, including cooling fan kit N8101-553F Heat Sink 1st 2nd N8101-616F N8101-546F N8101-547F N8101-548F N8101-549F N8101-550F N8101-551F N8101-552F (Standard) NOTE: Minimum one processor kit from above must be installed. The processors must be the same to configure dual processor system. NEC Corporation Revision 7.0 – July 17, 2013 12 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 3 Memory 3.1 Memory Configuration Refer to the section in accordance with your memory configuration: Independent Channel: Refer to 3.1.1 Memory Sparing Configuration: Refer to 3.1.2 Memory Mirroring / Memory Lockstep Configuration: Refer to 3.1.3 3.1.1 Independent Channel Configuration Available slots: 12 per processor Category Product Name / Description Part Number Unbuffered DIMM (UDIMM) 8GB DDR3-1333 UNB Memory Kit 2x 4GB Unbuffered ECC DIMM, DDR3L-1333(PC3L-10600) NOTE: - Up to four sets (eight slots) per processor can be installed - This DIMM doesn’t support x4 SDDC. N8102-435F Registered DIMM (RDIMM) 4GB DDR3-1600 REG Memory Kit 2x 2GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) NOTE: - This DIMM doesn’t support x4 SDDC. N8102-468F 8GB DDR3-1600 REG Memory Kit 2x 4GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) 16GB DDR3-1600 REG Memory Kit 2x 8GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) 32GB DDR3-1600 REG Memory Kit 2x 16GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) 64GB DDR3-1333 LR Memory Kit 2x 32GB Load Reduced ECC DIMM, DDR3L-1333(PC3L-10600) N8102-469F Load Reduced DIMM (LRDIMM) N8102-470F N8102-471F N8102-440F NOTE: Minimum one memory kit per processor must be installed. It is recommended to install memory kits in multiples of two (four identical DIMMs) for quad-channel symmetric memory configurations to increase memory transfer speed. When two processors are installed, balance the DIMMs across the two processors. Mix configurations of UDIMM/RDIMM/LRDIMM are not supported. NEC Corporation Revision 7.0 – July 17, 2013 13 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 3.1.2 Memory Sparing Configuration Available slots: 12 per processor Product Name / Description Part Number 6GB DDR3-1600 REG Memory Kit 3x 2GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) 12GB DDR3-1600 REG Memory Kit 3x 4GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) 24GB DDR3-1600 REG Memory Kit 3x 8GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) 48GB DDR3-1600 REG Memory Kit 3x 16GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) N8102-476 N8102-477 N8102-499 N8102-500 NOTE: Minimum one memory kit per processor must be installed. The configured memories must be identical. When two processors are installed, balance the DIMMs across the two processors. The logical memory capacity at the time of memory sparing becomes two-thirds of physical capacity with configurations less than 4GB DIMM and five-sixth physical capacity with configurations more than 8GB DIMM. The maximum memory transfer rate is 1066 MHz. 3.1.3 Memory Mirroring / Memory Lockstep Configuration Available slots: 12 per processor Product Name / Description Part Number 4GB DDR3-1600 REG Memory Kit 2x 2GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) 8GB DDR3-1600 REG Memory Kit 2x 4GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) 16GB DDR3-1600 REG Memory Kit 2x 8GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) 32GB DDR3-1600 REG Memory Kit 2x 16GB Registered ECC DIMM, DDR3L-1600(PC3L-12800) N8102-472 N8102-473 N8102-474 N8102-475 NOTE: Minimum one memory kit per processor must be installed. NEC Corporation Revision 7.0 – July 17, 2013 14 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Memory Configuration Feature Comparison See the table below for feature comparisons of memory configurations supported. Independent Channel Memory Sparing Memory Lockstep Memory Mirroring Performance Data Protection Best No Better Multiple single bit error protection Better No Redundancy Data Correction Available Memory No ECC, x4 SDDC Full physical memory No ECC, x8 SDDC Full physical memory Available Memory Channels Notes 4 Partly ECC, x4 SDDC 2/3 physical memory (2, 4GB DIMM) 5/6 physical memory (8, 16GB DIMM) 4 Good Multiple single bit and multi bit error protection Fully ECC, x4 SDDC Half physical memory 4 4 All DIMMs in the system must be identical. Paired DIMMs must be identical. Paired DIMMs must be identical. - Maximum Memory Speed See the table below for the actual maximum memory transfer speed in Independent Channel / Memory Sparing Configuration. DDR3 memory speed depends on the type of DIMMs, the native memory bus speed of the memory controller and memory configuration. All memory buses operate at the clock frequency of the DIMM with the lowest frequency. The maximum memory transfer rate is 1066 MHz with Memory Sparing Configuration. Processor Type # of DIMMs per processor Populated DIMMs Memory Power Setting DIMM Speed E5-2609 - - - 1066 MHz E5-2620 E5-2630L E5-2640 UDIMM: 4GB - RDIMM: 2, 4, 8, 16 GB LRDIMM: 32GB Up to 8 DIMMs 10 or more DIMMs Up to 8 DIMMs UDIMM: 4GB 10 or more DIMMs - RDIMM: 2, 4, 8, 16 GB Up to 8 DIMMs UDIMM: 4GB 10 or more DIMMs Up to 8 DIMMs Low (1.35V) Normal (1.5V) Low (1.35V) Normal (1.5V) Low (1.35V) Normal (1.5V) Low (1.35V) Normal (1.5V) Low (1.35V) Normal (1.5V) - 1066 MHz 1333 MHz 1333 MHz 1066 MHz 1066 MHz 1333 MHz 1066 MHz 1066 MHz 1333 MHz 1333 MHz 1600 MHz 1066 MHz 1066 MHz 1333 MHz 1066 MHz E5-2650 E5-2650L E5-2643 E5-2670 E5-2690 10 or more DIMMs NEC Corporation Revision 7.0 – July 17, 2013 15 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Maximum Available Memory See the table below for the maximum memory size that you can actually use on your system. The maximum available memory is less than the maximum physical memory supported by your system because some chipsets require PCI resource space of about 750MB. PCI resource requirements vary depending on the type and the number of PCI cards you are using. Maximum Memory Size Supported by Operating Systems Microsoft Windows Server 2003 R2, Standard Edition Microsoft Windows Server 2008 Standard Microsoft Windows Server 2003 R2, Standard x64 Edition Microsoft Windows Server 2008 Standard (x64) Microsoft Windows Server 2008 R2 Standard Microsoft Windows Server 2003 R2, Enterprise Edition Microsoft Windows Server 2008 Enterprise Microsoft Windows Server 2003 R2, Enterprise x64 Edition Microsoft Windows Server 2008 Enterprise (x64) Microsoft Windows Server 2008 R2 Enterprise Microsoft Windows Server 2012 Standard Microsoft Windows Server 2012 Datacenter Red Hat Enterprise Linux 5 Red Hat Enterprise Linux 6 Red Hat Enterprise Linux 5 (EM64T) Red Hat Enterprise Linux 6 (x86_64) 1 VMware ESX 4.1 VMware ESXi 5.0 / 5.1 1 2 2 4 GB Maximum Available Memory 32 GB 4 GB (HW-DEP enabled) App. 2 GB(HW-DEP disabled) 32 GB 64 GB 64 GB 1 TB 2 TB 768 GB 768 GB 4 TB 768 GB 16 GB 16 GB 1 TB 2 TB 256 GB or 1 TB 2TB 768 GB 768 GB 256 GB or 768 GB 768 GB Up to 255GB of main memory is available to each virtual machine. Up to 1TB of main memory is available to each virtual machine. NEC Corporation Revision 7.0 – July 17, 2013 16 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 4 Internal Hard Disk Drives 4.1 RAID Configuration Refer to the section in accordance with your disk form factor and RAID configuration. Up to eight 2.5-inch Drives Available Interface Non-RAID Refer to 4.2.1 SATA RAID 0/1/10 Refer to 4.2.2 SAS, SATA 512MB Cache Refer to 4.2.3 SAS, SATA 1GB Cache / Battery Refer to 4.2.4 SAS, SATA 1GB Cache / CacheVault Refer to 4.2.5 SAS, SATA RAID 5/6/50/60 Up to sixteen 2.5-inch Drives Available Interface Refer to 4.2.6 SAS, SATA 512MB Cache Refer to 4.2.7 SAS, SATA 1GB Cache / Battery Refer to 4.2.8 SAS, SATA 1GB Cache / CacheVault Refer to 4.2.9 SAS, SATA RAID 0/1/10 RAID 5/6 NOTE: Up to four hard drives can be installed in the Embedded SATA configuration. Hot plug insertion/removal are not supported in the Embedded SATA configuration. All drives within a RAID array should be of the same type, capacity and rotation speed. Use the same rotational speed of the SAS hard drives in one system. Up to two kinds of drives can be mixed in one system. To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process. It is recommended to set RAID array configuration drives less than eight in order to minimize the risk of becoming multiple hard drives failure. SAS and SATA hard drives must be installed in separate drive groups. Group #1 Group #2 NEC Corporation Group #3 Group #4 For optional RAID controller driver to install Windows Server 2003 R2, download from the NEC website at: http://www.nec.com/en/global/prod/express/download/index.html Revision 7.0 – July 17, 2013 17 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 4.2 Internal Drive Configuration 4.2.1 Up to four Drives with Embedded SATA Controller Category Product Name / Description Part Number Storage Controller Embedded SATA Controller 4 x SATA ports Internal SATA Cable 1 x mini-SAS to 1 x mini-SAS 2.5-inch Drive Cage 8 x 2.5-inch Hot-plug hard drive bays 250GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 500GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 1TB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm (Standard) Cable Drive Cage Drive 4 slots available SATA HDD (Standard) (Standard) N8150-356 N8150-357 N8150-358 NOTE: Hot plug insertion/removal are not supported in the configuration. The maximum transfer speed for Slot 2 and Slot 3 is 3 Gb/s. NEC Corporation Revision 7.0 – July 17, 2013 18 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 4.2.2 Up to eight Drives with RAID 0/1 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (512MB, RAID 0/1) LSI MegaRAID SAS 9267-8i RAID 0/1/10, 512 MB, Int. 8, PCIe 2.0 x8, 6Gb/s RAID Battery Backup Unit for LSI MegaRAID SAS 9267-8i Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS, 2 sets 2.5-inch Drive Cage 8 x 2.5-inch hot plug drive bays 300GB 10K Hot Plug 2.5-inch SAS HDD 1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 450GB 10K Hot Plug 2.5-inch SAS HDD 1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 600GB 10K Hot Plug 2.5-inch SAS HDD 1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 900GB 10K Hot Plug 2.5-inch SAS HDD 1x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 1.2TB HDD 10K Hot Plug 2.5-inch SASHDD 1x 1.2TB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 73.2GB 15K Hot Plug 2.5-inch SAS HDD 1x 73.2 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 146.5GB 15K Hot Plug 2.5-inch SAS HDD 1x 146.5 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 300GB 15K Hot Plug 2.5-inch SAS HDD 1x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 250GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 500GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 1TB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 200GB Hot Plug 2.5-inch SAS SSD 1x 200 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s 400GB Hot Plug 2.5-inch SAS SSD 1x 400 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s N8103-149 RAID BBU Recommended Cable Drive Cage Drive 8 slots available SAS HDD SATA HDD SAS SSD N8103-153 (Standard) (Standard) N8150-301 N8150-322 N8150-304 N8150-332 N8150-408 N8150-302 N8150-303 N8150-331 N8150-356 N8150-357 N8150-358 N8150-711 N8150-712 NOTE: All drives within a RAID array should be of the same type, capacity and rotation speed. SAS and SATA hard drives must be installed in separate drive groups. Up to two kinds of drives can be mixed in one system. NEC Corporation Revision 7.0 – July 17, 2013 19 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 4.2.3 Up to eight Drives with RAID 5/6 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (512MB, RAID 0/1) LSI MegaRAID SAS 9267-8i RAID0/1/5/6/10/50/60, 512 MB, Int. 8, PCIe 2.0 x8, 6Gb/s RAID Battery Backup Unit for LSI MegaRAID SAS 9267-8i Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS, 2 sets 2.5-inch Drive Cage 8 x 2.5-inch hot plug drive bays 300GB 10K Hot Plug 2.5-inch SAS HDD 1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 450GB 10K Hot Plug 2.5-inch SAS HDD 1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 600GB 10K Hot Plug 2.5-inch SAS HDD 1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 900GB 10K Hot Plug 2.5-inch SAS HDD 1x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 1.2TB HDD 10K Hot Plug 2.5-inch SASHDD 1x 1.2TB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 73.2GB 15K Hot Plug 2.5-inch SAS HDD 1x 73.2 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 146.5GB 15K Hot Plug 2.5-inch SAS HDD 1x 146.5 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 300GB 15K Hot Plug 2.5-inch SAS HDD 1x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 250GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 500GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 1TB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 200GB Hot Plug 2.5-inch SAS SSD 1x 200 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s 400GB Hot Plug 2.5-inch SAS SSD 1x 400 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s N8103-150 RAID BBU Recommended Cable Drive Cage Drive 8 slots available SAS HDD SATA HDD SAS SSD N8103-153 (Standard) (Standard) N8150-301 N8150-322 N8150-304 N8150-332 N8150-408 N8150-302 N8150-303 N8150-331 N8150-356 N8150-357 N8150-358 N8150-711 N8150-712 NOTE: All drives within a RAID array should be of the same type, capacity and rotation speed. Use the same rotational speed of the SAS hard drives in one system. SAS and SATA hard drives must be installed in separate drive groups. Up to two kinds of drives can be mixed in one system. To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process. NEC Corporation Revision 7.0 – July 17, 2013 20 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 4.2.4 Up to eight Drives with RAID 5/6 Controller with 1 GB Cache/Battery Category Product Name / Description Part Number Storage Controller Required RAID Controller (1GB, RAID 0/1/5/6) LSI MegaRAID SAS 9267-8i RAID 0/1/5/6/10/50/60, 1 GB, Int. 8, PCIe 2.0 x8, 6Gb/s RAID Battery Backup Unit for LSI MegaRAID SAS 9267-8i MegaRAID CacheCade for LSI MegaRAID SAS 9267-8i NOTE: - SSD used for cache is required - The SSD capacity which can be used as read cache is up to 512 GB. N8103-151 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS, 2 sets 2.5-inch Drive Cage 8 x 2.5-inch hot plug drive bays 300GB 10K Hot Plug 2.5-inch SAS HDD 1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 450GB 10K Hot Plug 2.5-inch SAS HDD 1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 600GB 10K Hot Plug 2.5-inch SAS HDD 1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 900GB 10K Hot Plug 2.5-inch SAS HDD 1x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 1.2TB HDD 10K Hot Plug 2.5-inch SASHDD 1x 1.2TB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 73.2GB 15K Hot Plug 2.5-inch SAS HDD 1x 73.2 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 146.5GB 15K Hot Plug 2.5-inch SAS HDD 1x 146.5 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 300GB 15K Hot Plug 2.5-inch SAS HDD 1x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 250GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 500GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 1TB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 200GB Hot Plug 2.5-inch SAS SSD 1x 200 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s 400GB Hot Plug 2.5-inch SAS SSD 1x 400 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s (Standard) RAID BBU Recommended SSD Caching Recommended Cable Drive Cage Drive 8 slots available SAS HDD SATA HDD SAS SSD N8103-153 N8103-156 (Standard) N8150-301 N8150-322 N8150-304 N8150-332 N8150-408 N8150-302 N8150-303 N8150-331 N8150-356 N8150-357 N8150-358 N8150-711 N8150-712 NOTE: All drives within a RAID array should be of the same type, capacity and rotation speed. Use the same rotational speed of the SAS hard drives in one system. SAS and SATA hard drives must be installed in separate drive groups. Up to two kinds of drives can be mixed in one system. To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process. NEC Corporation Revision 7.0 – July 17, 2013 21 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 4.2.5 Up to eight Drives with RAID 5/6 Controller with 1 GB Cache/CacheVault Category Product Name / Description Part Number Storage Controller Required RAID Controller (1GB, RAID 0/1/5/6) LSI MegaRAID SAS 9270CV-8i (with CV) RAID0/1/5/6/10/50/60, 1GB Cahce, Int. 8ports, PCIe 3.0(x8), 6Gb/s, flash cache protection modules included MegaRAID CacheCade for LSI MegaRAID SAS NOTE: - SSD used for cache is required - The SSD capacity which can be used as read cache is up to 512 GB. N8103-152 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS, 2 sets 2.5-inch Drive Cage 8 x 2.5-inch hot plug drive bays 300GB 10K Hot Plug 2.5-inch SAS HDD 1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 450GB 10K Hot Plug 2.5-inch SAS HDD 1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 600GB 10K Hot Plug 2.5-inch SAS HDD 1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 900GB 10K Hot Plug 2.5-inch SAS HDD 1x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 1.2TB HDD 10K Hot Plug 2.5-inch SASHDD 1x 1.2TB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 73.2GB 15K Hot Plug 2.5-inch SAS HDD 1x 73.2 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 146.5GB 15K Hot Plug 2.5-inch SAS HDD 1x 146.5 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 300GB 15K Hot Plug 2.5-inch SAS HDD 1x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 250GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 500GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 1TB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 200GB Hot Plug 2.5-inch SAS SSD 1x 200 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s 400GB Hot Plug 2.5-inch SAS SSD 1x 400 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s K410-270(00) SSD Caching Recommended Cable Required Drive Cage Drive 8 slots available SAS HDD SATA HDD SAS SSD N8103-156 (Standard) N8150-301 N8150-322 N8150-304 N8150-332 N8150-408 N8150-302 N8150-303 N8150-331 N8150-356 N8150-357 N8150-358 N8150-711 N8150-712 NOTE: All drives within a RAID array should be of the same type, capacity and rotation speed. Use the same rotational speed of the SAS hard drives in one system. SAS and SATA hard drives must be installed in separate drive groups. Up to two kinds of drives can be mixed in one system. To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process. For VMware ESXi 5.x installation, to download the CIM provider (LSI SMI-S provider 00.32.V0.03) is required. For VMware ESXi 5.x systems, monitoring the status of a RAID array with NEC ESMPRO is not supported. NEC Corporation Revision 7.0 – July 17, 2013 22 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 4.2.6 Up to sixteen Drives with RAID 0/1 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (512MB, RAID 0/1) LSI MegaRAID SAS 9267-8i RAID 0/1/10, 512MB, Int. 8, PCIe 2.0 x8, 6Gb/s RAID Battery Backup Unit for LSI MegaRAID SAS 9267-8i Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS, 6 sets 2.5-inch Drive Cage 8 x 2.5-inch hot plug drive bays 2.5-Inch Drive Cage 8 x 2.5-inch hot plug drive bays Including 6sets of 1 x mini-SAS to 1 x mini-SAS cable, SAS expander card 300GB 10K Hot Plug 2.5-inch SAS HDD 1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 450GB 10K Hot Plug 2.5-inch SAS HDD 1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 600GB 10K Hot Plug 2.5-inch SAS HDD 1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 900GB 10K Hot Plug 2.5-inch SAS HDD 1x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 1.2TB HDD 10K Hot Plug 2.5-inch SASHDD 1x 1.2TB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 73.2GB 15K Hot Plug 2.5-inch SAS HDD 1x 73.2 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 146.5GB 15K Hot Plug 2.5-inch SAS HDD 1x 146.5 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 300GB 15K Hot Plug 2.5-inch SAS HDD 1x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 250GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 500GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 1TB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 200GB Hot Plug 2.5-inch SAS SSD 1x 200 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s 400GB Hot Plug 2.5-inch SAS SSD 1x 400 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s N8103-149 RAID BBU Recommended Cable Drive Cage Optional Drive Cage Required Drive 16 slots available SAS HDD SATA HDD SAS SSD N8103-153 (Standard) (Standard) N8154-39 N8150-301 N8150-322 N8150-304 N8150-332 N8150-408 N8150-302 N8150-303 N8150-331 N8150-356 N8150-357 N8150-358 N8150-711 N8150-712 NOTE: All drives within a RAID array should be of the same type, capacity and rotation speed. Use the same rotational speed of the SAS hard drives in one system. SAS and SATA hard drives must be installed in separate drive groups. Up to two kinds of drives can be mixed in one system. To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process. NEC Corporation Revision 7.0 – July 17, 2013 23 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 4.2.7 Up to sixteen Drives with RAID 5/6 Controller with 512 MB Cache Category Product Name / Description Part Number Storage Controller Required RAID Controller (512MB, RAID 0/1/5/6) LSI MegaRAID SAS 9267-8i RAID0/1/5/6/10/50/60, 512MB, Int. 8, PCIe 2.0 x8, 6Gb/s RAID Battery Backup Unit for LSI MegaRAID SAS 9267-8i Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS, 6 sets 2.5-inch Drive Cage 8 x 2.5-inch hot plug drive bays 2.5-Inch Drive Cage 8 x 2.5-inch hot plug drive bays Including six sets of 1 x mini-SAS to 1 x mini-SAS cable, SAS expander card 300GB 10K Hot Plug 2.5-inch SAS HDD 1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 450GB 10K Hot Plug 2.5-inch SAS HDD 1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 600GB 10K Hot Plug 2.5-inch SAS HDD 1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 900GB 10K Hot Plug 2.5-inch SAS HDD 1x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 1.2TB HDD 10K Hot Plug 2.5-inch SASHDD 1x 1.2TB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 73.2GB 15K Hot Plug 2.5-inch SAS HDD 1x 73.2 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 146.5GB 15K Hot Plug 2.5-inch SAS HDD 1x 146.5 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 300GB 15K Hot Plug 2.5-inch SAS HDD 1x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 250GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 500GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 1TB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 200GB Hot Plug 2.5-inch SAS SSD 1x 200 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s 400GB Hot Plug 2.5-inch SAS SSD 1x 400 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s N8103-150 RAID BBU Recommended Cable Drive Cage Optional Drive Cage Required Drive 16 slots available SAS HDD SATA HDD SAS SSD N8103-153 (Standard) (Standard) N8154-39 N8150-301 N8150-322 N8150-304 N8150-332 N8150-408 N8150-302 N8150-303 N8150-331 N8150-356 N8150-357 N8150-358 N8150-711 N8150-712 NOTE: All drives within a RAID array should be of the same type, capacity and rotation speed. Use the same rotational speed of the SAS hard drives in one system. SAS and SATA hard drives must be installed in separate drive groups. Up to two kinds of drives can be mixed in one system. To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process. It is recommended to set RAID array configuration drives less than eight in order to minimize the risk of becoming multiple hard drives failure.. NEC Corporation Revision 7.0 – July 17, 2013 24 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 4.2.8 Up to sixteen Drives with RAID 5/6 Controller with 1 GB Cache/Battery Category Product Name / Description Part Number Storage Controller Required RAID Controller (1GB, RAID 0/1/5/6) LSI MegaRAID SAS 9267-8i RAID 0/1/5/6/10/50/60, 1 GB, Int. 8, PCIe 2.0 x8, 6Gb/s RAID Battery Backup Unit for LSI MegaRAID SAS 9267-8i MegaRAID CacheCade for LSI MegaRAID SAS NOTE: - SSD used for cache is required - The SSD capacity which can be used as read cache is up to 512 GB. N8103-151 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS,6 sets 2.5-inch Drive Cage 8 x 2.5-inch hot plug drive bays 2.5-Inch Drive Cage 8 x 2.5-inch hot plug drive bays Including six sets of 1 x mini-SAS to 1 x mini-SAS cable, SAS expander card 300GB 10K Hot Plug 2.5-inch SAS HDD 1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 450GB 10K Hot Plug 2.5-inch SAS HDD 1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 600GB 10K Hot Plug 2.5-inch SAS HDD 1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 900GB 10K Hot Plug 2.5-inch SAS HDD 1x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 1.2TB HDD 10K Hot Plug 2.5-inch SASHDD 1x 1.2TB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 73.2GB 15K Hot Plug 2.5-inch SAS HDD 1x 73.2 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 146.5GB 15K Hot Plug 2.5-inch SAS HDD 1x 146.5 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 300GB 15K Hot Plug 2.5-inch SAS HDD 1x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 250GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 500GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 1TB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 200GB Hot Plug 2.5-inch SAS SSD 1x 200 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s 400GB Hot Plug 2.5-inch SAS SSD 1x 400 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s (Standard) RAID BBU Recommended SSD Caching Recommended Cable Drive Cage Optional Drive Cage Required Drive 16 slots available SAS HDD SATA HDD SAS SSD N8103-153 N8103-156 (Standard) N8154-39 N8150-301 N8150-322 N8150-304 N8150-332 N8150-408 N8150-302 N8150-303 N8150-331 N8150-356 N8150-357 N8150-358 N8150-711 N8150-712 NOTE: All drives within a RAID array should be of the same type, capacity and rotation speed. Use the same rotational speed of the SAS hard drives in one system. SAS and SATA hard drives must be installed in separate drive groups. Up to two kinds of drives can be mixed in one system. To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process. It is recommended to set RAID array configuration drives less than eight in order to minimize the risk NEC Corporation Revision 7.0 – July 17, 2013 25 CONFIGURATION GUIDE – NEC Express5800/R120d-2M of becoming multiple hard drives failure. 4.2.9 Up to sixteen Drives with RAID 5/6 Controller with 1 GB Cache/CacheVault Category Product Name / Description Part Number Storage Controller Required RAID Controller (1GB, RAID 0/1/5/6) LSI MegaRAID SAS 9270CV-8i (with CV) RAID0/1/5/6/10/50/60, 1GB Cache, Int. 8ports, PCIe 3.0(x8), 6Gb/s, flash cache protection modules included MegaRAID CacheCade for LSI MegaRAID SAS NOTE: - SSD used for cache is required - The SSD capacity which can be used as read cache is up to 512 GB. N8103-152 Internal SAS/SATA Cable 1 x mini-SAS to 1 x mini-SAS,6 sets 2.5-inch Drive Cage 8 x 2.5-inch hot plug drive bays 2.5-Inch Drive Cage 8 x 2.5-inch hot plug drive bays Including six sets of 1 x mini-SAS to 1 x mini-SAS cable, SAS expander card 300GB 10K Hot Plug 2.5-inch SAS HDD 1 x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 450GB 10K Hot Plug 2.5-inch SAS HDD 1 x 450 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 600GB 10K Hot Plug 2.5-inch SAS HDD 1 x 600 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 900GB 10K Hot Plug 2.5-inch SAS HDD 1x 900 GB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 1.2TB HDD 10K Hot Plug 2.5-inch SAS HDD 1x 1.2TB SAS HDD, 2.5-inch, 6Gb/s, 10,000 rpm 73.2GB 15K Hot Plug 2.5-inch SAS HDD 1x 73.2 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 146.5GB 15K Hot Plug 2.5-inch SAS HDD 1x 146.5 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 300GB 15K Hot Plug 2.5-inch SAS HDD 1x 300 GB SAS HDD, 2.5-inch, 6Gb/s, 15,000 rpm 250GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 250 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 500GB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 500 GB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 1TB 7.2K Hot Plug 2.5-inch SATA HDD 1 x 1 TB SATA HDD, 2.5-inch, 6Gb/s, 7,200 rpm 200GB Hot Plug 2.5-inch SAS SSD 1x 200 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s 400GB Hot Plug 2.5-inch SAS SSD 1x 400 GB SAS SSD, eMLC, 2.5-inch, 6Gb/s (Standard) SSD Caching Recommended Cable Drive Cage Optional Drive Cage Required Drive 16 slots available SAS HDD SATA HDD SAS SSD N8103-156 (Standard) N8154-39 N8150-301 N8150-322 N8150-304 N8150-332 N8150-408 N8150-302 N8150-303 N8150-331 N8150-356 N8150-357 N8150-358 N8150-711 N8150-712 NOTE: All drives within a RAID array should be of the same type, capacity and rotation speed. Use the same rotational speed of the SAS Hard drives in one system. SAS and SATA hard drives must be installed in separate drive groups. Up to two kinds of drives can be mixed in one system. For VMware ESXi 5.x installation, to download the CIM provider (LSI SMI-S provider 00.32.V0.03) is required. For VMware ESXi 5.x systems, monitoring the status of a RAID array with NEC ESMPRO is not NEC Corporation Revision 7.0 – July 17, 2013 26 CONFIGURATION GUIDE – NEC Express5800/R120d-2M supported. To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process. It is recommended to set RAID array configuration drives less than eight in order to minimize the risk of becoming multiple hard drives failure. 5 Optical Drive Category Product Name / Description Part Number Internal 1 slot available Internal Slim DVD-ROM drive Slim DVD-ROM drive Internal DVD Super Multi Drive Slim DVD Super Multi drive, not including writing software External DVD-ROM drive DVD-ROM drive, Bus powered, 1.2 A required N8151-100 External N8151-107F N8160-91 NOTE: Up to 1 optical drive can be connected. NEC Corporation Revision 7.0 – July 17, 2013 27 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 6 Internal Tape / RDX Drives 6.1 Tape / RDX Drive Selection Refer to the section in accordance with your type of tape drives: DAT: Refer to 6.2.1 RDX: Refer to 6.2.2 NOTE: Tape devices cannot be directly connected to VMware systems. For VMware systems, it is recommended to connect and configure an additional backup server via network. 6.2 Tape / RDX Configuration 6.2.1 DAT Category Product Name / Description Part Number Controller Internal USB Controller 1 x USB port Internal USB cable 1 x Internal USB to 1 x USB device (Standard) Internal DAT (USB) DDS4 / DAT72 / DAT160, Native capacity 80 GB NOTE: DDS1 / DDS2 / DDS3 format are not supported N8151-78A Category Product Name / Description Part Number Controller Internal USB Controller 1 x USB port Internal USB cable 1 x Internal USB to 1 x USB device (Standard) Internal RDX (USB) N8151-105 Cable Drive 1 bay available 6.2.2 RDX Cable Drive 1 bay available NEC Corporation (Standard) Revision 7.0 – July 17, 2013 K410-264(00) 28 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 7 PCI Riser Card / PCI Card Please refer to Supported PCI Cards and Installable Slots with regard to the position of PCI slot which can mount PCI card supported. 7.1 PCI Riser Card Product Name / Description Part Number PCIe Riser Card Kit 2 x PCIe 3.0 x8 PCIe x16 Riser Card Kit 1 x PCIe 3.0 x16 PCI-X Riser Card Kit 1 x 64-bit/133 MHz PCI-X, 1x PCIe 3.0 x8 PCI Riser Card Kit 2x 64-bit/33 MHz PCI (5V) NOTE: The riser card is make-to-order product. Please consult our sales representative in regard to production lead time. The card is not supported on VMware ESXi systems. (Standard) 7.2 N8116-25 N8116-26 N8116-27 Full Length PCI Card installation Kit For a full-length PCI card (D=312mm/12.28 in) installation in PCI Slot #1B Product Name / Description Part Number Full Length PCI Card installation Kit For a full-length installation, contains special heat sinks N8116-28 NOTE: Obtain the graphics card installation kit in addition to this product when to install graphics board. Since this product is make-to-order manufacturing, the support is provided individually. Contact our sales representative for details. 7.3 Graphics Card Installation Kit For an installation of the video card which is used for Microsoft RemoteFX Product Name / Description Part Number Graphics Card Installation Kit Power cables for video card (six-pin), a retainer to secure the graphics card N8116-29 NOTE: Since this product is make-to-order manufacturing, the support is provided individually. Contact our sales representative for details. This product doesn't support/guarantee installation of the video card. NEC Corporation Revision 7.0 – July 17, 2013 29 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 7.4 Network Interface Controller Category Riser 1GbE 10GbE Adapter 1GbE 10GbE SPF+ Module NEC Corporation Product Name / Description Part Number Dual Port 1000BASE-T Riser Card Broadcom® BCM5718 Gigabit Ethernet Controller PCIe 2.0 x8 Dual Port 10GBASE SFP+ Riser Card Broadcom® BCM57810 Converged Controller PCIe 3.0 x8 NOTE: - N8104-129 SFP+ Module is required to connect with an optical cable. - Up to two SFP+ Modules can be installed. - Supports up to two adapters of 10Gb Converged Network Adapter and 10Gb Network Adapter on any supported operating systems, excluding Red Hat Enterprise Linux 6(x86), 6.1 and 6.2(x86_64). N8104-135 1000BASE-T Adapter Broadcom ® BCM5718 Gigabit Ethernet Controller PCIe 2.0 x1 Dual Port 1000BASE-T Adapter Broadcom ® BCM5718 Gigabit Ethernet Controller PCIe 2.0 x1 Dual Port 1000BASE-T Adapter Intel® 82580 Gigabit Ethernet Controller PCIe 2.0 x4, Max. 2 Quad Port 1000BASE-T Adapter Broadcom ® BCM5719 Gigabit Ethernet Controller PCIe 2.0 x4 NOTE: - Network cables with RJ-45 plug covers cannot be used. - Jumbo frame is supported on Windows Server 2008 R2 and Redhat Enterprise Linux operating systems. N8104-138 10GBASE Adapter (SFP+/2ch) Broadcom NetXtreme II BCM957711 10G SFP+ Dual Port Network Interface Card PCIe 2.0 x8 NOTE: - N8104-129 SFP+ Module is required to connect with an optical cable. - Up to 2 SFP+ Modules can be installed. - Supports up to two adapters of 10Gb Converged Network Adapter and 10Gb Network Adapter on any supported operating systems, excluding Red Hat Enterprise Linux 6(x86), 6.1 and 6.2(x86_64). Dual Port 10Gb Converged Network Adapter BROCADE 1020 Dual Port 10Gbps Converged Network Adapter PCIe 2.0 x8, 2 x SFP modules, Max. one adapter NOTE: - Supports up to two adapters of 10Gb Converged Network Adapter and 10Gb Network Adapter on any supported operating systems, excluding Red Hat Enterprise Linux 6(x86), 6.1 and 6.2(x86_64). N8104-128 SFP+ Module (10G-SR) 1 x SFP+ Module for N8104-128 and N8104-137 N8104-129 Revision 7.0 – July 17, 2013 N8104-137 N8104-132 N8104-145 N8104-133 N8104-131 30 CONFIGURATION GUIDE – NEC Express5800/R120d-2M NIC Teaming feature – NIC Teaming and bonding features See the table below for supported network interfaces and OS combinations. Windows Server 2003 R2 and Windows Server 2008 support BASP (Broadcom Advanced Server Program) teaming while Windows Server 2012 and Linux support teaming with bonding function supported by OS. Network Interface Team Operating Systems 1GbE NIC Embedded 1GbE NIC and N8104-135/-138/-132/-133 Up to four teams per one system Up to four ports per one team 10GbE NIC N8104-128/137 Up to two teams per one system Up to two ports per one team Windows Server 2003 R2 Windows Server 2008 Windows Server 2008 R2 Windows Server 2012 Red Hat Enterprise Linux Windows Server 2008 Windows Server 2008 R2 Windows Server 2012 Red Hat Enterprise Linux NOTE: NIC Teaming feature is not supported on iSCSI interfaces. The network interfaces for teaming must be the same. When 10GbE and 1GbE NIC teaming are mixed, the teams must be up to four per one system. Using iSCSI See the table below for supported network interfaces and operating system combinations. Category Network Interface Operating Systems 1GbE Embedded 1GbE NIC N8104-138 N8104-132 N8104-133 N8104-128 Windows Server 2008 R2, Windows Server 2012, Red Hat Linux, VMware Windows Server 2008 R2, Windows Server 2012, Red Hat Linux, VMware Windows Server 2008 R2, Windows Server 2012, Red Hat Linux, VMware Windows Server 2008 R2, Windows Server 2012, Red Hat Linux, VMware Windows Server 2008, Windows Server 2008 R2, Red Hat Linux, VMware 10GbE NOTE: NIC Teaming feature is not supported on iSCSI interfaces. NEC Corporation Revision 7.0 – July 17, 2013 31 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 7.5 External Storage Controller 7.5.1 RAID Controller Category Product Name / Description Part Number Controller RAID Controller (1GB, RAID0/1/5/6) LSI MegaRAID SAS 9285-8e RAID0/1/5/6/10/50/60, 1GB, Ext. 8, PCIe 2.0 x8, SAS 6Gb/s, SATA 6Gb/s RAID Battery Backup Unit for LSI MegaRAID SAS 9285-8e N8103-160 RAID BBU N8103-162 NOTE: To configure a large-capacity RAID array, it is recommended to configure in RAID 6 or RAID 60 in order to minimize the risk of becoming multiple hard drives failure during the RAID rebuilding process. It is recommended to set RAID array configuration drives less than eight in order to minimize the risk of becoming multiple hard drives failure. 7.5.2 Fibre Channel / SAS Controller Category Product Name / Description Part Number Fibre Channel Fibre Channel Controller (1ch) Emulex LightPulse LPe1250-F8 Host Bus Adapter 8Gb/s, Optical, PCIe 2.0 x8 Fibre Channel Controller (2ch) Emulex LightPulse LPe12002-M8 Host Bus Adapter 8Gb/s, Optical, PCIe 2.0 x8 Fibre Channel Controller (1ch) Emulex LightPulse LPe16000B-M6 Host Bus Adapter 16Gb/s, Optical, PCIe 3.0 x8 Fibre Channel Controller (2ch) Emulex LightPulse LPe16002B-M6 Host Bus Adapter 16Gb/s, Optical, PCIe 3.0 x8 SAS Controller LSI SAS9212-4i4e Host Bus Adapter 6Gb/s SAS, Int. 4 / Ext. 4, 7-pin SATA / SFF-8088, PCIe 2.0 x8 N8190-153 SAS N8190-154 N8190-157 N8190-158 N8103-142 NOTE: Up to two 16Gb/s Fiber Channel Controller can be installed. 7.6 Serial Port Adapter Product Name / Description Part Number Serial Port Adapter N8117-01A Serial port fixed to PCI bracket NOTE: Up to one Serial Port Adapter can be installed. NEC Corporation Revision 7.0 – July 17, 2013 32 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 8 Other Add-in Components 8.1 Power Supply Module Product Name / Description Part Number 450W Hot Plug Power Supply 1 x 450 Watt 80 PLUS® Platinum 800W Hot Plug Power Supply 1 x 800 Watt 80 PLUS® Platinum 1000W Hot Plug Power Supply 1 x 1000 Watt 80 PLUS® Platinum N8181-86F N8181-87F N8181-88F NOTE: The power units must be the same to configure redundancy. Use the NEC Power Supply Selector to select appropriate size for power units. For details, please visit the NEC website at: http://www.nec.com/en/global/prod/express/collateral/tools/PowerSelector_G01.xls 8.2 Redundant Fan Kit Product Name / Description Part Number Redundant Fan Kit 5 hot plug redundant cooling fans for R120d-2M N8181-89 8.3 Trusted Platform Module Kit Product Name / Description Part Number Trusted Platform Module Kit TPM 1.2 module N8115-08 NOTE: The kit is not available in China. The kit is not removable after attachment. "TPM Support" in BIOS setup menu must be activated prior to use of this kit. To use Windows BitLocker drive encryption, be sure to keep the "recovery password" of BitLocker function. The recovery password is required to restore data for hardware replacement during a system error. 8.4 Internal Flash Memory Available socket: 1 Product Name / Description Part Number Internal Flash Memory Internal flash memory to enable software and tools in the EXPRESSBUILDER DVD without DVD media NOTE: Before use, software and tools must be copied from the EXPRESSBUILDER DVD to the flash memory. The following operations can be performed with the flash memory: - Installation of Windows server with express setup - Installation of Starter Pack—the package of NEC qualified drivers and system setting tools - Installation of NEC ESMPRO Agent and Universal RAID Utility - Performance of the Test and Diagnosis Tool N8115-07 NEC Corporation Revision 7.0 – July 17, 2013 33 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 8.5 Flash FDD Choose the Flash FDD if you need to prepare an alternative device for a floppy drive. Product Name / Description Part Number Flash FDD USB flash emulating USB floppy disk, Native capacity 1.44 MB N8160-86 NOTE: Up to one drive can be connected. 8.6 Front Bezel Product Name / Description Part Number Front Bezel Front bezel for R120d-2M N8146-26F 9 Add-on Components 9.1 17-inch LCD Console Drawer Category Drawer w/ KVM Drawer Cable Drawer w/o KVM Drawer Keypad NEC Corporation Product Name / Description Part Number 17-inch LCD Console Drawer (8port) 17-inch LCD, US 83-keys Keyboard, Optical mouse, 8 port KVM switch, 1U height Switch Unit Connection Cable Set (USB, 1.8m) 1.8 m, 1 x 15-pin mini D-sub to 1 x 15-pin mini D-sub / 1 x 4-pin USB A Switch Unit Connection Cable Set (USB, 3m) 3 m, 1 x 15-pin mini D-sub to 1 x 15-pin mini D-sub / 1 x 4-pin USB A Switch Unit Connection Cable Set (USB, 5m) 5 m, 1 x 15-pin mini D-sub to 1 x 15-pin mini D-sub / 1 x 4-pin USB A 17inch LCD Console Unit 1U 17-inch LCD, US 83-keys Keyboard, Optical mouse, 1U height, 4-pin USB B to 4-pin USB A cable 2 m, PS/2 Y-splitter cable 2m, 15-pin mini D-sub VGA cable 2 m 17inch LCD Console Drawer (1port) 17-inch LCD, US 103-keys Keyboard with 10-key, Touch pad with 3-button, 1U height, 4-pin USB B to 4-pin USB A cable 1.8 m, Two PS/2 cable 1.8 m, 15-pin mini D-sub VGA cable 1.8 m Keyboard Unit (JP) JP 108-keys Keyboard with 10-key for N8143-84F 17inch LCD Console Drawer (1port) Keyboard Unit (UK) UK 104-keys Keyboard with 10-key, for N8143-84F 17inch LCD Console Drawer (1port) N8143-77F Revision 7.0 – July 17, 2013 K410-118(1A) K410-118(03) K410-118(05) N8143-76F N8143-84F N8143-85 N8143-87 34 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 9.2 KVM Switch Category Product Name / Description Part Number KVM Switch Server Switch Unit (8 server) 1U USB 8 port KVM switch N8191-12F Switch Unit Connection Cable Set (USB,1.8m) 1.8 m, 1 x 15-pin mini D-sub to 1 x 15-pin mini D-sub / 1 x 4-pin USB A Switch Unit Connection Cable Set (USB,3m) 3 m, 1 x 15-pin mini D-sub to 1 x 15-pin mini D-sub / 1 x 4-pin USB A Switch Unit Connection Cable Set (USB,3m) 5 m, 1 x 15-pin mini D-sub to 1 x 15-pin mini D-sub / 1 x 4-pin USB A Switch Unit Connection Cable 1.8 m 1.8 m, 1 x 15-pin mini D-sub - 1x 15-pin mini D-Sub / 2x PS/2 K410-118(1A) Cable KVM Cascading 9.3 K410-118(03) K410-118(05) K410-119(1A) Cable Management Arm Product Name / Description Part Number Cable Management Arm 2U Kit For R120d-2M N8143-78 9.4 Server Management License The server integrates the EXPRESSSCOPE Engine 3 as standard. Refer to Server Management for the standard management features. For more extensive remote KVM and remote media features, choose the following kit. Product Name / Description Part Number Remote KVM and Media License Kit N8115-04 License for one server. Remote KVM and remote media are enabled regardless of OS status. Remote KVM: Displays a graphics console on the web browser of the remote terminal (PC/server). Controls keyboard and mouse via the remote terminals' web browser Remote media: Enables the user to use the CD / DVD / FD / Flash memory of the remote terminals (PC/server) as if accessing the local drives. NOTE: Remote KVM and remote media features are not available for virtual machines. 9.5 Medium and Cartridge Category Product Name Drive supported Part Number DAT DAT160(80GB) Medium 5 pack DAT160 WORM (80GB) Medium RDX Cartridge (320GB) RDX Cartridge (500GB) RDX Cartridge (1TB) RDX Cartridge (1.5TB) N8151-78A N8151-78A N8151-105 N8151-105 N8151-105 N8151-105 N8152-14 N8152-21 N8153-01 N8153-02 N8153-03 N8153-04 RDX NEC Corporation Revision 7.0 – July 17, 2013 35 CONFIGURATION GUIDE – NEC Express5800/R120d-2M References Server Management The EXPRESSSCOPE Engine 3, integrated into the server, provides superior remote control and system management features listed in the table below. Standard Hardware monitoring Boot monitoring Alerting Remote KVM (via LAN) Remote control (via LAN) Others Remote wakeup Centralized management Industry standard 1 2 3 4 Temperature/voltage/power/ fan /degeneration (memory/hard drive) Hardware event log collection With Remote KVM and Media License kit 1 2, 3, 4 2, 4 GUI-based screen (OS console) - Remote reset/power on-off/ dump OS shutdown Remote media (CD/DVD/FD) 1 - 1 Server Management Command Line Protocol (DMTF compliant) Remote control via Web browser (without dedicated app) Remote batch 2 1 1 Booting, BIOS/POST stall, OS stall, shutdown HW error, Boot error and OS panic (by SNMP, E-Mail) POST/BIOS setup, DOS utility Panic screen, Boot screen Text-based screen (OS console) 1 Scheduling (without UPS) Set automatic IP address via DNS/DHCP Wake On LAN, Wake On Ring Monitoring and control of multiple servers IPMI 2.0 2.0 The feature is not supported on VMware ESXi systems. The optional serial port is not available for the feature. Monitoring boot screens is not supported on VMware systems. In VMware systems, only the direct console user interface is supported. NEC Corporation Revision 7.0 – July 17, 2013 36 CONFIGURATION GUIDE – NEC Express5800/R120d-2M OS Support Matrix for PCI Cards and Embedded Controllers Product Name N8103-149 N8103-150 N8103-151 N8103-152 N8103-160 N8103-142 N8190-153 N8190-154 N8190-157 N8190-158 N8104-135 N8104-138 N8104-132 N8104-133 N8104-145 N8104-137 N8104-128 N8104-131 Embedded SATA non-RAID Controller Embedded 1GbE NIC RAID Controller (512 MB, RAID 0/1) RAID Controller (512 MB, RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) SAS Controller Fibre Channel Controller Fibre Channel Controller (2ch) Fibre Channel Controller Fibre Channel Controller (2ch) Dual Port 1000BASE-T Riser Card 1000BASE-T adapter Dual Port 1000BASE-T Adapter Quad Port 1000BASE-T Adapter Dual Port 1000BASE-T Adapter Dual Port 10GBASE SFP+ Riser Card 10GBASE adapter (SFP+/2ch) Dual Port 10Gb Converged Network Adapter NEC Corporation Revision 7.0 – July 17, 2013 ESX 4.1 ESXi 5.0 ESXi 5.1 RHEL 5 x64 RHEL 5 RHEL 6 x64 RHEL 6 WS 2003R2 x64 WS 2003R2 WS 2008 x64 WS 2008 WS 2008R2 WS 2012 Part number - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 37 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Supported PCI Cards and Installable Slots Standard Riser Card Slots Part Number N8103-149 N8103-150 N8103-151 N8103-152 N8103-160 N8103-142 N8190-153 N8190-154 N8190-157 N8190-158 N8104-135 N8104-138 N8104-132 N8104-145 N8104-133 N8104-137 N8104-128 N8104-131 N8117-01A 1 2 3 4 Product Name RAID Controller (512 MB, RAID 0/1) RAID Controller (512 MB, RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) SAS Controller Fibre Channel Controller Fibre Channel Controller (2ch) Fibre Channel Controller Fibre Channel Controller (2ch) Dual Port 1000BASE-T Riser Card 1000BASE-T adapter Dual Port 1000BASE-T Adapter Dual Port 1000BASE-T Adapter Quad Port 1000BASE-T Adapter Dual Port 10GBASE SFP+ Riser Card 10GBASE adapter (SFP+/2ch) Dual Port 10Gb Converged Network Adapter Serial Port Adapter #1A #1B #2B #1C #2C #3C 1 #1D - - - 3 4 3 - Available in dual-processor configuration To install a PCI card for more than 220 mm (8.66 in), N8116-28 full-length PCI installation kit is required. Not available in up to sixteen drives configuration Not available with Windows Server 2003 R2. NEC Corporation Revision 7.0 – July 17, 2013 38 CONFIGURATION GUIDE – NEC Express5800/R120d-2M N8116-25 PCIe x16 Riser Card Kit Slots Part Number N8103-149 N8103-150 N8103-151 N8103-152 N8103-160 N8103-142 N8190-153 N8190-154 N8190-157 N8190-158 N8104-135 N8104-138 N8104-132 N8104-145 N8104-133 N8104-137 N8104-128 N8104-131 N8117-01A 1 2 3 4 Product Name RAID Controller (512 MB, RAID 0/1) RAID Controller (512 MB, RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) SAS Controller Fibre Channel Controller Fibre Channel Controller (2ch) Fibre Channel Controller Fibre Channel Controller (2ch) Dual Port 1000BASE-T Riser Card 1000BASE-T adapter Dual Port 1000BASE-T Adapter Dual Port 1000BASE-T Adapter Quad Port 1000BASE-T Adapter Dual Port 10GBASE SFP+ Riser Card 10GBASE adapter (SFP+/2ch) Dual Port 10Gb Converged Network Adapter Serial Port Adapter #1A - #1B #2C #3C 1 3 4 3 #1C - #1D - Available in dual-processor configuration To install a PCI card for more than 220 mm (8.66 in), N8116-28 full-length PCI installation kit is required. Not available in up to sixteen drives configuration Not available with Windows Server 2003 R2. N8116-26 PCI-X Riser Card Kit Slots Part Number N8103-149 N8103-150 N8103-151 N8103-152 N8103-160 N8103-142 N8190-153 N8190-154 N8190-157 N8190-158 N8104-135 N8104-138 N8104-132 N8104-145 N8104-133 N8104-137 N8104-128 N8104-131 N8117-01A NEC Corporation Product Name RAID Controller (512 MB, RAID 0/1) RAID Controller (512 MB, RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) SAS Controller Fibre Channel Controller Fibre Channel Controller (2ch) Fibre Channel Controller Fibre Channel Controller (2ch) Dual Port 1000BASE-T Riser Card 1000BASE-T adapter Dual Port 1000BASE-T Adapter Dual Port 1000BASE-T Adapter Quad Port 1000BASE-T Adapter Dual Port 10GBASE SFP+ Riser Card 10GBASE adapter (SFP+/2ch) Dual Port 10Gb Converged Network Adapter Serial Port Adapter #1A #1B #2B #1C #2C #3C 1 #1D - - 3 4 3 - Revision 7.0 – July 17, 2013 - 39 CONFIGURATION GUIDE – NEC Express5800/R120d-2M 1 2 3 4 Available in dual-processor configuration To install a PCI card for more than 220 mm (8.66 in), N8116-28 full-length PCI installation kit is required. Not available in up to sixteen drives configuration Not available with Windows Server 2003 R2. N8116-27 64-bit PCI Riser Card Kit Slots Part Number N8103-149 N8103-150 N8103-151 N8103-152 N8103-160 N8103-142 N8190-153 N8190-154 N8190-157 N8190-158 N8104-135 N8104-138 N8104-132 N8104-145 N8104-133 N8104-137 N8104-128 N8104-131 N8117-01A 1 2 3 4 Product Name RAID Controller (512 MB, RAID 0/1) RAID Controller (512 MB, RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) RAID Controller (1 GB,RAID 0/1/5/6) SAS Controller Fibre Channel Controller Fibre Channel Controller (2ch) Fibre Channel Controller Fibre Channel Controller (2ch) Dual Port 1000BASE-T Riser Card 1000BASE-T adapter Dual Port 1000BASE-T Adapter Dual Port 1000BASE-T Adapter Quad Port 1000BASE-T Adapter Dual Port 10GBASE SFP+ Riser Card 10GBASE adapter (SFP+/2ch) Dual Port 10Gb Converged Network Adapter Serial Port Adapter #1A #1B #2B #1C #2C #3C 1 #1D - - - 3 4 3 - Available in dual-processor configuration To install a PCI card for more than 220 mm (8.66 in), N8116-28 full-length PCI installation kit is required. Not available in up to sixteen drives configuration Not available with Windows Server 2003 R2. NEC Corporation Revision 7.0 – July 17, 2013 40 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Copyright Notice and Liability Disclaimer The information contained herein is subject to change without notice. Microsoft and Windows Server are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries Intel and Xeon are registered trademarks or trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Linux is a trademark of Linus Torvalds. Red Hat is a registered trademark of Red Hat, Inc. in the U.S. All other products, brands, or trade names used in this document are trademarks or registered trademarks of their respective holders. NEC shall not be liable for technical or editorial errors or omissions contained herein. For hard drive capacity measurements, 1 GB = 1 billion bytes. Actual formatted capacity is less. NEC Corporation Revision 7.0 – July 17, 2013 41 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Revision History Revision Date Description 7.0 July 17, 2013 6.0 April 16, 2013 5.0 December 21, 2012 4.0 October 31, 2012 3.0 July 3, 2012 New products added: 1.2TB 10K Hot Plug 2.5-inch SAS HDD / N8150-408 Dual Port 1000BASE-T Adapter / N8104-145 New products added: Fibre Channel Controller (1ch) / N8190-157 Fibre Channel Controller (2ch) / N8190-158 RDX Cartridge (1.5TB) / N8153-04 Part number changed: Internal DVD Super Multi Drive / N8151-107F External DVD-ROM Drive / N8160-91 RDX Cartridge (320GB) / N8153-01 RDX Cartridge (500GB) / N8153-02 RDX Cartridge (1TB) / N8153-03 Discontinued products removed: 100GB SSD / N8150-709 400GB SSD / N8150-710 Others: Remove N8151-69A Internal DAT (USB) Support NIC teaming on Windows Server 2012 systems. Support N8103-142 SAS Controller on Windows Server 2012 systems Part number changed: Internal DAT (USB) / N8151-69A Internal DAT (USB) / N8151-78A Others: Add Windows Server 2012 to the list of operating system supported Support N8103-152 RAID Controller on VMware ESXi 5.x systems Support 10GbE NIC teaming with two or more 10GbE NIC cards. Update OS support matrix New products added: RAID Controller (1GB, RAID 0/1/5/6) / N8103-152 Internal SAS/SATA Cable / K410-270(00) 200GB SSD / N8150-711 400GB SSD / N8150-712 Discontinued products removed: 100GB SSD / N8150-707 SAS Controller / N8103-104A Other: Add VMware ESXi 5.1 to the list of operating system supported Support bonding feature on Linux operating system using 10GbE NIC Update Regulatory list Update OS support matrix New products added: Xeon E5-2620 Processor Kit / N8101-616F Internal RDX / N8151-105 Internal USB Cable / K410-264(00) 17-inch LCD Console Drawer (1port) / N8143-84F Switch Unit Connection Cable 1.8 m / K410-119(1A) Discontinued products removed: Internal RDX / K8151-86 Other: Add KC in Regulatory list Add description for expansion slots Support jumbo frame on Quad Port 1000BASE-T Adapter Add description for using iSCSI Add OS support information for embedded controllers into support matrix table NEC Corporation Revision 7.0 – July 17, 2013 42 CONFIGURATION GUIDE – NEC Express5800/R120d-2M Revision Date Description 2.0 May 14, 2012 1.2 April 18, 2012 1.1 April 13, 2012 1.0 March 30, 2012 New products added: 17-inch LCD Console Drawer (8port) / N8143-77F Discontinued products removed: 17inch LCD Console Unit (1U/8port) / N8143-69F Others: Add VMWare ESX 4.1 to the list of operating system supported Correct the incorrect core/thread information for Xeon Processor E5-2643 Correct the incorrect note in Independent Channel Configuration Correct incorrect maximum available memory size for Red Hat Enterprise Linux 5 (EM64T) Correct the incorrect description for 1000W Hot Plug Power Supply Support N8103-142 SAS Controller on VMware ESXi 5.0 system Support N8104-133 Quad Port 1000BASE-T Adapter on VMware Others: Correct wrong parts number for the Internal Flash Memory Others: Add the notes for the External Storage Controller, and Serial Port Adapter Initial release NEC Corporation Revision 7.0 – July 17, 2013 43