Alcoa Fastening Systems & Rings THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. R Ti-Matic ® CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFSR TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 C ENGINEERING STANDARD M L F 4 A PIN SLEEVE 15 R D 5 9 E 10 G 101°30' 98°30' GRIP 3 11 H S B Z MANUFACTURER'S IDENTIFICATION 8 MATERIAL IDENTIFICATION 6 9 GRIP IDENTIFICATION INSTALLED FASTENER PART NUMBER NOM DIA 7 TABLE I C Ø A (B) ØD E F ØG H R (S) ØZ SINGLE TENSILE HOLE HEAD HEAD MIN ±.001 MAX MAX GAGE GAGE RAD DESIGN MIN SHEAR STRENGTH DIA THEO. HEIGHT ±.0001 HEIGHT MAX REF STRENGTH LBS +.003 INTER. ONLY LBS -.000 MAX 15 8 UB100-EV05-( ) 05 .333 .072 .844 .163 .220 .011 .2831 UB100-EV06-( ) 06 .386 .080 .875 .198 .250 .013 .3271 UB100-EV08-( ) 08 .507 .105 1.000 .259 .305 .017 .4319 UB100-EV10-( ) 10 .634 .137 1.250 .311 .320 .020 .5450 .0206 .0171 .0243 .0205 .0310 .0270 .0367 .0325 1 2 1 .010 .232 .205 1980 1150 .164 .015 .292 .248 2925 1690 .199 .020 .361 .325 5005 2900 .260 .026 .430 .383 7220 4170 .312 1 MINIMUM ULTIMATE SINGLE SHEAR AND TENSILE STRENGTH, IN POUNDS, OF INSTALLED FASTENER. 2 APPLIES TO GRIPS 05-04 MAX, 06-05 MAX, 08-06 MAX, 10-07 MAX AND GREATER. IN SHORTER GRIPS A TRUE COMPOSITE SHEAR TEST CANNOT BE OBTAINED. 3 TRIM FLASH NOT TO EXCEED .005 MAXIMUM LENGTH ABOVE HEAD OF PIN. 4 SOLID OR SPLIT LOCK COLLAR AT MANUFACTURER'S OPTION. SPLIT NOT TO EXCEED .020. 5 KNURLED TO RETAIN FASTENER COMPONENTS. NOT PART OF INSTALLED FASTENER 6 BLIND SIDE HEAD MAY BE INSTALLED ON 5 MAX SLOPE. R PER DCN 12950, CHANGED FROM Alcoa Fastening Systems TO Alcoa Fastening SYstems & Rings AND AFS TO AFSR DIMENSIONS IN INCHES ISSUED 5/23/1994 REVISED 3/31/2015 PAGE 1 OF 3 ® Ti-Matic BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, 100 FLUSH HEAD, TITANIUM/A-286 CRES (95 KSI SHEAR) SINGLE ACTION INSTALLATION PROCUREMENT SPEC T0102 DRAWN BY CHECKED BY J. SCHLOBOHM SIGNATURE ON FILE UB100-EV SK12637 This dra win g/docu mentatio n is control led b y either the De pa rtme nt of Sta te, Intern ationa l Tra ffic In Arms R egu la tio ns or the De partmen t of C ommerce , Expo rt Admi nistratio n Reg ula ti ons an d may Req uire a n expo rt li cense /l icen se excep ti on pri or to b ein g tra nsferred to a forei gn na ti ona l, i nsid e or ou tsid e of th e United Sta te s. EAR/ECCN EAR 99. Th ese co mm oditie s, techn olo gy or software we re expo rte d fro m the U nited States in a ccorda nce wi th the Exp ort Ad mini stra ti on Re gul ation s. Dive rsion co ntrary to U.S. la w proh ibited . Alcoa Fastening Systems & Rings THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. R Ti-Matic ® CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFSR TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 ENGINEERING STANDARD 7 IDENTIFICATION: HUCK SYMBOL , "EV", AND GRIP DASH NUMBER. 8 THE AVERAGE READING OF THE SMALLEST & LARGEST OBSERVED VALUE ON THE SAME SPECIMEN MUST BE EQUAL TO OR GREATER THAN THE STATED MINIMUM DIAMETER. THIS IS APPLICABLE TO DESIGN GRIP RANGE. 9 CONCENTRICITY: CONICAL SURFACE OF FLUSH HEAD TO "D" DIAMETER TO BE WITHIN .010 F.I.M. 10 OPTIONAL DRIVE WASHER FOR INSTALLATION WITH BLUNT NOSED TOOL. NOT PART OF INSTALLED FASTENER. 11 "E" LENGTH OF DIAMETER "D" MAY BE .002 UNDERSIZED. 12 DIAMETER OF PIN HEAD SHALL NOT EXCEED "D" MAX AND MAY BE .002 BELOW "D" MIN. 13 OVERLAP IN DESIGN GRIP RANGE MAKES FASTENER WELL-SUITED FOR COMPOSITE STRUCTURES WITH LARGE GRIP TOLERANCES. FASTENER IS INTENDED TO BE INSTALLED IN "DESIGN GRIP RANGE". FASTENERS INSTALLED IN GRIPS ABOVE "DESIGN GRIP RANGE" PERFORM RELIABLY PROVIDED THAT THE INSTALLED PIN AND COLLAR FLUSHNESS REQUIREMENTS ARE MET. 14 THE GRIP RANGE OF UB100-EV06-02 IS .120 TO .157. 15 DIAMETER "D" MAY BE .0005" OVERSIZE FOR COATED PARTS. TABLE I I 13 GRIP DESIGN GRIP OVERLAP DASH RANGE GRIP NO. MAX MIN. MAX. 14 GRIP NUMBER TABULATION 05 06 08 (L) M MAX (L) M MAX 10 (L) M MAX (L) M MAX 02 .094 .157 .171 .300 .466 .329 .511 03 .156 .220 .235 .363 .529 .392 .574 .433 .648 04 .219 .282 .298 .425 .591 .454 .636 .495 .710 .501 .779 05 .281 .345 .360 .488 .654 .517 .699 .558 .773 .564 .842 06 .344 .407 .423 .550 .716 .579 .761 .620 .835 .626 .904 07 .406 .470 .485 .613 .779 .642 .824 .683 .898 .689 .967 08 .469 .532 .548 .675 .841 .704 .886 .745 .960 .751 1.029 09 .531 .595 .610 .738 .904 .767 .949 .808 1.023 .814 1.092 10 .594 .657 .673 .800 .966 .829 1.011 .870 1.085 .876 1.154 11 .656 .720 .735 .863 1.029 .892 1.074 .933 1.148 .939 1.217 12 .719 .782 .798 .954 1.136 .995 1.210 1.001 1.279 13 .781 .845 .860 1.017 1.199 1.058 1.273 1.064 1.342 14 .844 .907 .923 1.120 1.335 1.126 1.404 15 .906 .970 .985 1.183 1.398 1.189 1.467 16 .969 1.032 1.048 1.245 1.460 1.251 1.529 DIMENSIONS IN INCHES R ISSUED PER DCN 12950, CHANGED FROM Alcoa Fastening Systems TO Alcoa Fastening SYstems & Rings AND AFS TO AFSR 5/23/1994 REVISED 3/31/2015 PAGE 2 OF 3 ® Ti-Matic BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, 100 FLUSH HEAD, TITANIUM/A-286 CRES (95 KSI SHEAR) SINGLE ACTION INSTALLATION PROCUREMENT SPEC T0102 DRAWN BY CHECKED BY J. SCHLOBOHM SIGNATURE ON FILE UB100-EV SK12637 This dra win g/docu mentatio n is control led b y either the De pa rtme nt of Sta te, Intern ationa l Tra ffic In Arms R egu la tio ns or the De partmen t of C ommerce , Expo rt Admi nistratio n Reg ula ti ons an d may Req uire a n expo rt li cense /l icen se excep ti on pri or to b ein g tra nsferred to a forei gn na ti ona l, i nsid e or ou tsid e of th e United Sta te s. EAR/ECCN EAR 99. Th ese co mm oditie s, techn olo gy or software we re expo rte d fro m the U nited States in a ccorda nce wi th the Exp ort Ad mini stra ti on Re gul ation s. Dive rsion co ntrary to U.S. la w proh ibited . Alcoa Fastening Systems & Rings THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. R Ti-Matic ® CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFSR TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 ENGINEERING STANDARD TABLE I I I FINISH CODE COMPONENT DESCRIPTION SLEEVE PIN NONE LOCK COLLAR 16 SLEEVE PIN AC LOCK COLLAR 16 MATERIAL FINISH LUBE 16 A-286 PER CHEMISTRY OF SAE-AMS5737 NONE 38-6-44 TITANIUM PER CHEMISTRY OF SAE-AMS4957 OR SAE-AMS-T-9047 NONE A-286 PER CHEMISTRY OF SAE-AMS5737 OR TYPE 316 CRES PER CHEMISTRY OF SAE-AMS5690 A-286 PER CHEMISTRY OF SAE-AMS5737 38-6-44 TITANIUM PER CHEMISTRY OF SAE-AMS4957 OR SAE-AMS-T-9047 A-286 PER CHEMISTRY OF SAE-AMS5737 OR TYPE 316 CRES PER CHEMISTRY OF SAE-AMS5690 NONE OR CETYL ALCOHOL PER SAE-AS87132 OR DRY FILM LUBE PER SAE-AS5272 TYPE 1 PASSIVATE PER DICRONITE DL-5 SAE-AMS2700 LUBE PER DOD-L-85645 TYPE 2 OR TYPE 8 ALUMINUM COAT PER NAS4006 NONE NONE OR CETYL ALCOHOL PER SAE-AS87132 OR DRY FILM LUBE PER SAE-AS5272 TYPE 1 PASSIVATE PER DICRONITE DL-5 LUBE SAE-AMS2700 PER DOD-L-85645 TYPE 2 OR TYPE 8 16 LUBE AND LOCK COLLAR MATERIAL AT MANUFACTURER'S OPTION. PART NUMBER UB100-EV06 -06 (*) NO SUFFIX DENOTES NO PROTECTIVE FINISH. AC - SLEEVE IS ALUMINUM COATED PER NAS4006 W - DENOTES OPTIONAL DRIVE WASHER. IF BLANK NO DRIVE WASHER PROVIDED. GRIP NUMBER IN 1/16" INCREMENTS NOMINAL SHANK DIAMETER IN 32nd INCHES. MATERIAL DESIGNATOR - A-286 CRES SLEEVE/TITANIUM PIN. Ti-Matic BLIND BOLT FASTENER, HIGH STRENGTH PULL-TYPE, POSITIVE MECHANICAL LOCK, 100 FLUSH HEAD. SINGLE ACTION INSTALLATION WITHOUT LOCKING COLLAR CAP. R DIMENSIONS IN INCHES R ISSUED PER DCN 12950, CHANGED FROM Alcoa Fastening Systems TO Alcoa Fastening SYstems & Rings AND AFS TO AFSR 5/23/1994 REVISED 3/31/2015 PAGE 3 OF 3 PROCUREMENT SPEC T0102 DRAWN BY CHECKED BY J. SCHLOBOHM SIGNATURE ON FILE ® Ti-Matic BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, 100 FLUSH HEAD, TITANIUM/A-286 CRES (95 KSI SHEAR) SINGLE ACTION INSTALLATION UB100-EV SK12637 This dra win g/docu mentatio n is control led b y either the De pa rtme nt of Sta te, Intern ationa l Tra ffic In Arms R egu la tio ns or the De partmen t of C ommerce , Expo rt Admi nistratio n Reg ula ti ons an d may Req uire a n expo rt li cense /l icen se excep ti on pri or to b ein g tra nsferred to a forei gn na ti ona l, i nsid e or ou tsid e of th e United Sta te s. EAR/ECCN EAR 99. Th ese co mm oditie s, techn olo gy or software we re expo rte d fro m the U nited States in a ccorda nce wi th the Exp ort Ad mini stra ti on Re gul ation s. Dive rsion co ntrary to U.S. la w proh ibited .