THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. T Unimatic ® CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFSR TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 Alcoa Fastening Systems & Rings GRIP ADVANCED BLIND BOLT ENGINEERING STANDARD C B M L S K N A 5 W 8 SLEEVE D J 6 11 E PIN 9 INSTALLED FASTENER 4 3 RAD R 7 HEAD ID WITHOUT DRIVE WASHER PART NUMBER NOM Ø A DIA. HEAD B +.010 -.000 C MIN. TABLE I ØD E ØJ K SLEEVE MAX ±.005 ±.030 ±.001 10 N R (S) Ø W SINGLE TENSILE SPINDLE HOLE ±.060 RAD. DESIGN MIN. SHEAR RET. LIMITS MAX. REF +.003 1 1 -.000 2 UABP-EU05-( ) 05 UABP-EU06-( ) 06 UABP-EU08-( ) 08 .328 .296 .394 .356 .525 .475 .067 .844 .163 .300 .800 .140 .010 .232 .223 1980 1150 575 .164 .080 .875 .198 .320 .375 .830 .160 .015 .292 .270 2925 1690 845 .199 .107 1.000 .259 .370 .975 .190 .018 .361 .355 5000 2900 1440 .260 1. MINIMUM ULTIMATE SINGLE SHEAR AND TENSILE STRENGTHS IN POUNDS OF INSTALLED FASTENER. 2. APPLIES TO GRIPS 05-03 MAX, 06-04 MAX, 08-05 MAX AND UP. IN SHORTER GRIPS, A TRUE COMPOSITE SHEAR TEST CANNOT BE OBTAINED. 3. TRIM FLASH NOT TO EXCEED .005 MAXIMUM LENGTH ABOVE HEAD OF PIN. 4. SOLID OR SPLIT LOCK COLLAR - MANUFACTURER'S OPTION. SPLIT NOT TO EXCEED .020 WIDTH. 5. KNURLED TO FACILITATE FASTENER ASSEMBLY. NOT PART OF THE INSTALLED FASTENER. 6. BLIND SIDE HEAD MAY BE INSTALLED ON 7 MAXIMUM SLOPE. 7. IDENTIFICATION: HUCK SYMBOL, "C" (MATERIAL) AND GRIP DASH NUMBER. 8. THE AVERAGE READING OF THE SMALLEST & LARGEST OBSERVED VALUE ON THE SAME SPECIMEN MUST BE EQUAL TO OR GREATER THAN THE STATED MINIMUM DIAMETER. THIS IS APPLICABLE TO DESIGN GRIP RANGE. 9. DRIVE WASHER TO FACILITATE INSTALLATION ONLY. NOT PART OF THE INSTALLED FASTENER. 10. -05 DIA SIZE ALSO AVAILABLE WITH REDUCED O.D. DRIVE ANVIL OF .312 .005. SEE PART NUMBER EXAMPLES. 11. "E" LENGTH OF "Ø D" MAY BE .002 UNDERSIZE. T ISSUED PER DCN 12950, CHANGED FROM Alcoa Fastening Systems TO Alcoa Fastening Systems & Rings AND AFS TO AFSR 9/20/2001 REVISED 3/31/2015 PAGE 1 OF 3 ® Unimatic ADVANCED SERIES BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, PROTRUDING HEAD, LARGE FOOT PRINT, A-286 CRES (95 KSI SHEAR) SINGLE ACTION INSTALLATION DIMENSIONS IN INCHES PROCUREMENT SPEC T0106 DRAWN BY CHECKED BY J. SCHLOBOHM SIGNATURE ON FILE UABP-EU SK12756 This dra win g/docu mentatio n is control led b y either the De pa rtme nt of Sta te, Intern ationa l Tra ffic In Arms R egu la tio ns or the De partmen t of C ommerce , Expo rt Admi nistratio n Reg ula ti ons an d may Req uire a n expo rt li cense /l icen se excep ti on pri or to b ein g tra nsferred to a forei gn na ti ona l, i nsid e or ou tsid e of th e United Sta te s. EAR/ECCN EAR 99. Th ese co mm oditie s, techn olo gy or software we re expo rte d fro m the U nited States in a ccorda nce wi th the Exp ort Ad mini stra ti on Re gul ation s. Dive rsion co ntrary to U.S. la w proh ibited . CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFSR TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 Alcoa Fastening Systems & Rings THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. T Unimatic ® ADVANCED BLIND BOLT ENGINEERING STANDARD TABLE I I GRIP NUMBER TABULATION GRIP OVERLAP DASH GRIP NUMBER MIN 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 NONE .084 .146 .209 .271 .334 .396 .459 .521 .584 .646 .709 .771 .834 .896 .959 DESIGN GRIP RANGE MIN. MAX. OVERLAP GRIP MAX .031 .094 .156 .219 .281 .344 .406 .469 .531 .594 .656 .719 .781 .844 .906 .969 .095 .157 .220 .282 .345 .407 .470 .532 .595 .657 .720 .782 .845 .907 .970 1.032 .111 .173 .236 .298 .361 .423 .486 .548 .611 .673 .735 .798 .860 .923 .985 1.048 05 (L) M MAX .283 .346 .408 .471 .533 .596 .658 .720 .782 .845 .908 .970 1.033 1.095 1.158 1.220 .447 .510 .572 .635 .697 .760 .822 .884 .946 1.009 1.072 1.134 1.197 1.259 1.322 1.384 GRIP OVERLAP DASH GRIP NUMBER MIN 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 .078 .140 .203 .265 .328 .390 .453 .515 .578 .640 .703 .765 .828 .890 .953 1.015 1.078 1.141 1.203 1.265 1.328 1.390 1.453 1.515 DESIGN GRIP RANGE MIN. MAX. OVERLAP GRIP MAX .094 .156 .219 .281 .344 .406 .469 .531 .594 .656 .719 .781 .844 .906 .969 1.031 1.094 1.156 1.219 1.281 1.344 1.406 1.469 1.531 .157 .220 .282 .345 .407 .470 .532 .595 .657 .720 .782 .845 .907 .970 1.032 1.095 1.157 1.220 1.282 1.345 1.407 1.470 1.532 1.595 .173 .236 .298 .361 .423 .486 .548 .611 .673 .736 .798 .861 .923 .986 1.049 1.111 1.173 1.236 1.298 1.360 1.423 1.485 1.548 1.610 06 08 (L) M MAX (L) M MAX .373 .435 .498 .560 .623 .685 .748 .810 .873 .936 .998 1.061 1.123 1.186 1.248 1.311 1.373 1.435 1.498 1.560 1.623 1.685 1.748 1.810 .570 .632 .695 .757 .820 .882 .945 1.007 1.070 1.133 1.195 1.258 1.320 1.383 1.445 1.508 1.570 1.633 1.695 1.758 1.820 1.883 1.945 2.008 .413 .475 .538 .600 .663 .725 .788 .850 .913 .976 1.038 1.101 1.163 1.226 1.288 1.351 1.413 1.476 1.538 1.601 1.663 1.726 1.788 1.851 .660 .722 .785 .847 .910 .972 1.035 1.097 1.160 1.223 1.285 1.348 1.410 1.473 1.535 1.598 1.660 1.723 1.785 1.848 1.910 1.973 2.035 2.098 TABLE I I I UABP-EU INSTALLED WEIGHT IN LBS (1000 pcs.) GRIP 5 DIA 6 DIA -01 -02 -03 -04 -05 -06 -07 -08 -09 -10 -11 -12 -13 T ISSUED 2.72 3.06 3.43 3.80 4.17 4.55 4.92 5.29 5.67 6.04 6.41 6.79 7.16 5.02 5.57 6.12 6.67 7.22 7.77 8.32 8.87 9.42 9.97 10.52 11.07 10.78 11.73 12.68 13.63 14.58 15.53 16.48 17.43 18.38 19.33 20.28 21.23 8 DIA -14 7.54 11.62 22.18 -15 7.91 12.17 23.13 -16 12.72 24.08 -17 13.27 25.03 -18 13.82 25.98 -19 14.37 26.93 -20 14.92 27.88 -21 15.47 28.83 -22 16.02 29.78 -23 16.57 30.73 -24 17.12 31.68 -25 17.67 32.63 DIMENSIONS IN INCHES PER DCN 12950, CHANGED FROM Alcoa Fastening Systems TO Alcoa Fastening Systems & Rings AND AFS TO AFSR 9/20/2001 REVISED 3/31/2015 PAGE 8 DIA GRIP 5 DIA 6 DIA 2 OF 3 ® Unimatic ADVANCED SERIES BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, PROTRUDING HEAD, LARGE FOOT PRINT, A-286 CRES (95 KSI SHEAR) SINGLE ACTION INSTALLATION PROCUREMENT SPEC T0106 DRAWN BY CHECKED BY J. SCHLOBOHM SIGNATURE ON FILE UABP-EU SK12756 This dra win g/docu mentatio n is control led b y either the De pa rtme nt of Sta te, Intern ationa l Tra ffic In Arms R egu la tio ns or the De partmen t of C ommerce , Expo rt Admi nistratio n Reg ula ti ons an d may Req uire a n expo rt li cense /l icen se excep ti on pri or to b ein g tra nsferred to a forei gn na ti ona l, i nsid e or ou tsid e of th e United Sta te s. EAR/ECCN EAR 99. Th ese co mm oditie s, techn olo gy or software we re expo rte d fro m the U nited States in a ccorda nce wi th the Exp ort Ad mini stra ti on Re gul ation s. Dive rsion co ntrary to U.S. la w proh ibited . Alcoa Fastening Systems & Rings THIS DRAWING, THE STRUCTURAL DESIGN DISCLOSED THEREIN AND THE TECHNICAL DATA AND ENGINEERING SERVICE REPRESENTED THEREBY ARE THE EXCLUSIVE PROPERTY OF HUCK INTERNATIONAL, INC. T CURRENT DESIGN ACTIVITY CAGE CODE 0HDW7 AFSR TUCSON OPERATIONS 3724 EAST COLUMBIA STREET TUCSON, ARIZONA 85714 PHONE (520) 519-7400 FAX (520) 519-7454 Unimatic ® ADVANCED BLIND BOLT ENGINEERING STANDARD TABLE I V MATERIAL FINISH CODE SLEEVE PIN LUBE FINISH LOCK COLLAR SLEEVE PIN LOCK COLLAR A-286 CRES PASSIVATE PASSIVATE PASSIVATE A-286 CRES A-286 CRES AMS 5737 NONE AMS2700 & AMS2700 & AMS2700 & OPTIONAL AMS 5737 AMS 5737 OR 316 CRES AMS-QQ-P-35 AMS-QQ-P-35 AMS-QQ-P-35 AMS5690 A-286 CRES ALUMINUM PASSIVATE PASSIVATE A-286 CRES A-286 CRES AMS 5737 D COAT AMS2700 & AMS2700 & OPTIONAL AMS 5737 AMS 5737 OR 316 CRES MIL-DTL-83488 AMS-QQ-P-35 AMS-QQ-P-35 AMS5690 CD CAD. PLATE A-286 CRES PASSIVATE AMS-QQ-P-416 PASSIVATE A-286 CRES A-286 CRES AMS 5737 TYPE I I CLEAR AMS2700 & AMS2700 & OPTIONAL AMS 5737 AMS 5737 OR 316 CRES DICHROMATE AMS-QQ-P-35 AMS-QQ-P-35 AMS5690 CLASS 2 AC A-286 CRES HIKOTE 1 PER PASSIVATE PASSIVATE A-286 CRES A-286 CRES AMS 5737 NAS4006 AND AMS2700 & AMS2700 & OPTIONAL AMS 5737 AMS 5737 OR 316 CRES BMS 10-85 AMS-QQ-P-35 AMS-QQ-P-35 AMS5690 LUBRICATION- WHEN LUBRICATED, PARTS SHALL BE LUBRICATED PER AS5272, AS87132 OR LOX COMPATIBLE DRY FILM LUBRICANT. (MANUFACTURER'S OPTIONS) HUCK PART NUMBER EXAMPLE: UABP - EU06 - 04( )R CODE "R" FOR REDUCED DRIVE ANVIL DIAMETER ON -05 DIA SIZE ONLY FINISH CODE - SEE TABLE GRIP NUMBER IN 16th INCHES. NOMINAL SHANK DIAMETER IN 32nd INCHES. MATERIAL DESIGNATOR - A286. Unimatic® ADVANCED SERIES BLIND BOLT FASTENER, HIGH STRENGTH PULL-TYPE, POSITIVE MECHANICAL LOCK, PROTRUDING HEAD, EXPANDED BULB. LARGE FOOT PRINT. DRIVE WASHER INCLUDED. DIMENSIONS IN INCHES T ISSUED PER DCN 12950, CHANGED FROM Alcoa Fastening Systems TO Alcoa Fastening Systems & Rings AND AFS TO AFSR 9/20/2001 REVISED 3/31/2015 PAGE 3 OF 3 Unimatic® ADVANCED SERIES BLIND BOLT FASTENER, HIGH STRENGTH, PULL-TYPE, POSITIVE MECHANICAL LOCK, PROTRUDING HEAD, LARGE FOOT PRINT, A-286 CRES (95 KSI SHEAR) SINGLE ACTION INSTALLATION PROCUREMENT SPEC T0106 DRAWN BY CHECKED BY J. SCHLOBOHM SIGNATURE ON FILE UABP-EU SK12756 This dra win g/docu mentatio n is control led b y either the De pa rtme nt of Sta te, Intern ationa l Tra ffic In Arms R egu la tio ns or the De partmen t of C ommerce , Expo rt Admi nistratio n Reg ula ti ons an d may Req uire a n expo rt li cense /l icen se excep ti on pri or to b ein g tra nsferred to a forei gn na ti ona l, i nsid e or ou tsid e of th e United Sta te s. EAR/ECCN EAR 99. Th ese co mm oditie s, techn olo gy or software we re expo rte d fro m the U nited States in a ccorda nce wi th the Exp ort Ad mini stra ti on Re gul ation s. Dive rsion co ntrary to U.S. la w proh ibited .