SL2 ICS50/SL2 ICS51
I•CODE SLI-L/I•CODE SLI-L HC
Rev. 3.0 — 14 March 2007
136430
Product data sheet
PUBLIC
1. General description
The I•CODE SLI-L/I•CODE SLI-L HC IC is a dedicated chip for smart label applications
with the need for a leaner custom-specific command set, smaller memory and/or a
product which takes care of the increasing demand for perfect customer privacy. This IC is
another member of our product family of smart label ICs that fully comply to the ISO
standard ISO/IEC 15693. The IC is also available in high capacitance version for small
label designs.
The I•CODE system offers the possibility of operating more than one label simultaneously
in the field of the reader antenna (Anticollision). It is designed for long range applications
with a special command for the use under the European regulations.
1.1 Anticollision
An intelligent anticollision function allows to operate more than one tag in the field
simultaneously. The anticollision algorithm selects each tag individually and ensures that
the execution of a transaction with a selected tag is performed correctly without data
corruption resulting from other tags in the field.
1.2 Contactless energy and data transfer
Whenever connected to a very simple and cheap type of antenna (as a result of the
13.56 MHz carrier frequency) made out of a few windings printed, winded, etched or
punched coil the I•CODE SLI-L/I•CODE SLI-L HC IC can be operated without line of sight
up to a distance of 1.5 m (gate width). No battery is needed. When the smart label is
positioned in the field of an interrogator antenna, the high speed RF communication
interface allows to transmit data with up to 53 kbit/s.
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
1.3 Security and privacy aspects
1. Unique Identifier (UID)
The UID can not be altered and guarantees the uniqueness of each label.
2. Password protected Label Destroy
With the 32-bit destroy password an addressed label can be destroyed with the
Destroy command. That status is irreversible and the label will never respond to any
command again.
3. Password protected Privacy Mode
With the 32-bit Privacy password a label can be set to the Privacy mode with the Set
to Privacy Mode command. In that mode the label will not respond to any command
except of the command Get Random Number till it receives again the right Privacy
password. That mode is especially designed to meet the increasing demand to take
care of the customers privacy.
4. Password protected EAS Functionality
With the 32-bit EAS password the addressed label can be set in a mode that the
commands Set EAS and Reset EAS are only executed by the label if the right EAS
password is transmitted to the label within the mentioned commands.
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
2 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
2. Features
2.1 I•CODE SLI-L RF interface
Contactless transmission of data and supply energy (no battery needed)
Operating distance: up to 1.5 m (depending on antenna geometry)
Operating frequency: 13.56 MHz (ISM, world-wide licence free available)
I•CODE SLI- L Functionality (ISO/IEC 15693)
Fast data transfer: up to 53 kbit/s
High data integrity: 16-bit CRC, framing
True anti-collision
Additional fast anti-collision read
Password protected Electronic Article Surveillance (EAS) incl. application selection
Application Family Identifier (AFI) supported
Data Storage Format Identifier (DSFID)
Privacy command with 32-bit Privacy password
Destroy command with 32-bit Destroy password
Long Range Command
Write distance equal to read distance
2.2 EEPROM
Data retention of 10 years
Write endurance 100.000 cycles
2.3 Security features
Unique identifier for each device
Lock mechanism for each user memory block (write protection)
Lock mechanism for DSFID, AFI, EAS
Password (32-bit) protected Label Destroy
Password (32-bit) protected Privacy Mode
Password (32-bit) protected EAS Functionality
3. Applications
Factory Automation
Industrial and Laundry
Asset Management
Libraries and Rental
4. Quick reference data
The data sheet describes the functionality of the smart label ICS I•CODE SLI- L and
I•CODE SLI- L HC. These ICs distinguish between the built in resonance capacitance.
The I•CODE SLI- L HC shows a higher capacitance value than the I•CODE SLI- L.
Therefore within the I•CODE SLI- L HC smaller label designs can be realized.
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
3 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
Table 1:
Quick reference data
Description
SL2 ICS50
I•CODE SLI- L
23.5
pF
SL2 ICS51
I•CODE SLI- L HC
97.0
pf
[1]
Min
Typ[1]
Symbol
Max
Unit
Typical values are not guaranteed. These values listed are at room temperature.
5. Ordering information
Table 2:
Ordering information
Type number
Package
Name
Description
Version
SL2 ICS5001EW/V1
FFC
sawn wafer 150 µm on film frame carrier
-
SL2 FCS5001 EV/DH
FCP
Flip Chip Package
-
SL2 MOS5001EV
MOA2
Module for contactless chip card ICs PLMCC-05
SOT500AA1
SL2 ICS5101EW/V1
FFC
sawn wafer 150 µm on film frame carrier
-
SL2 FCS5101 EV/DH
FCP
Flip Chip Package
-
SL2 MOS5101EV
MOA2
Module for contactless chip card ICs PLMCC-05
SOT500AA1
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
4 of 28
NXP Semiconductors
SL2 ICS50/SL2 ICS51
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
6. Block diagram
The SL2 ICS50/SL2 ICS51 IC consists of three major blocks:
Analog RF Interface
Digital Controller
EEPROM
The analog part provides stable supply voltage and demodulates data received from the
reader for being processed by the digital part. Further, the modulation transistor of the
analog part transmits data back to the reader.
The digital section includes the state machines, processes the protocol and handles
communication with the EEPROM.
Fig 1. Block diagram of TAG IC
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
5 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
7. Functional description
7.1 Block description
The label requires no internal power supply. Its contactless interface generates the power
supply and the system clock via the resonant circuitry by inductive coupling to the
interrogator. The interface also demodulates data that are transmitted from the
interrogator to the I•CODE Label, and modulates the electromagnetic field for data
transmission from the I•CODE Label to the interrogator.
Data are stored in a non-volatile memory (EEPROM). The EEPROM has a memory
capacity of 512 bit and is organized in 16 blocks consisting of 4 bytes each (1 block =
32 bits). The higher 8 blocks contain user data and the lowest 8 blocks contain the unique
identifier, the write access conditions and special data like AFI and DSFID.
7.2 Memory organization
The 512 bit EEPROM memory is divided into 16 blocks. A block is the smallest access
unit. Each block consists of 4 bytes (1 block = 32 bits). 4 blocks are summed up to 1 page.
Bit 0 in each byte represents the least significant bit (LSB) and bit 7 the most significant bit
(MSB), respectively.
The Memory is divided into 2 parts:
• Configuration Area
– Within this part of the memory all required information are stored like UID, Write
protection, Passwords and so on. Direct access to this memory area is not
possible.
• User Memory
– Within this area the user data are stored. Direct Read/write access to this part of
the memory is possible depending on the related write protection conditions.
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
6 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
Table 3.
Memory Organization
Page
Block
-2
-8
Byte 0
Byte 1
Byte 2
Byte 3
Description
Configuration Area for
internal use
-7
-6
-5
-1
-4
-3
-2
-1
0
0
User Memory
•
•
•
•
1
2
3
1
4
2 pages
4 bocks each
4 bytes reach
(total 32bytes)
5
6
7
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
7 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
7.2.1 Unique identifier
The 64-bit unique identifier (UID) is programmed during the production process according
to ISO/IEC 15693-3 and cannot be changed afterwards.
The numbering of the 64 bits is done according to ISO/IEC 15693-3 starting with the
LSB 1 and ending with the MSB 64. This is in contrast to the general used bit numbering
within a byte (starting with LSB 0).
The TAG type is a part of the UID (bit 41 to 48, after the manufacturer code which is “04h”
for NXP Semiconductors).
The TAG type of the SL2 ICS50/SL2 ICS51 is “03h”
Table 4.
Unique Identifier description
Byte
7
6
5
4
Name
UID 7
UID 6
UID 5
UID 4
Value
E0
04
03
IC manufacturer serial number
64 to 57
56 to 49
48 to 41
40 to 1
Bit
3
2
1
0
UID 3
UID 2
UID 1
UID 0
MSB
LSB
7.2.2 Configuration of delivered ICs
I•CODE SLI-L/I•CODE SLI-L HC ICs are delivered with the following configuration by NXP
Semiconductors:
• Unique Identifier is unique and read only
• Write Access Conditions allow to change user blocks, AFI, DSFID, EAS and
Passwords
•
•
•
•
•
•
•
All password bytes are 00h ( Privacy Password, Destroy Password, EAS Password)
Password protected Privacy Mode is disabled
EAS password protection is disabled
Status of EAS mode is not defined
AFI is supported and not defined
DSFID is supported and not defined
User Data memory is not defined
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
8 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
7.3 Communication principle
ISO 15693 command set
For detailed description of the protocol and timing please refer to ISO/IEC 15693-2
(modulation, bit-coding, framing) and 15693-3 (anticollision, timing, protocol).
Long Range command
For detailed description of the protocol and timing please refer to EPC Specification
“13.56 MHz ISM Band Class 1 Radio Frequency (RF) Identification Tag Interface
Specification”.
8. Command set
8.1 ISO 15693 command set
8.1.1 Mandatory commands
8.1.1.1
Inventory
As defined in ISO/IEC 15693-3.
Exception: If the Privacy or Destroy mode is enabled the label will not respond.
8.1.1.2
Stay quiet
As defined in ISO/IEC 15693-3.
8.1.2 Optional commands
8.1.2.1
Read single block
As defined in ISO/IEC 15693-3.
Option 0 (Option flag not set) is supported.
Option 1 (Option flag set) is supported.
If the Privacy or Destroy mode is enabled the label will not respond.
8.1.2.2
Write single block
Only Option 0 (Option flag is not set) is supported.
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
9 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.1.2.3
Lock block
Only Option 0 (Option flag is not set) is supported.
8.1.2.4
Select
As defined in ISO/IEC 15693-3.
8.1.2.5
Reset to ready
As defined in ISO/IEC 15693-3.
8.1.2.6
Write AFI
As defined in ISO/IEC 15693-3.
Only Option 0 (Option flag is not set) is supported.
8.1.2.7
Lock AFI
As defined in ISO/IEC 15693-3.
Only Option 0 (Option flag is not set) is supported.
8.1.2.8
Write DSFID
As defined in ISO/IEC 15693-3.
Only Option 0 (Option flag is not set) is supported.
8.1.2.9
Lock DSFID
As defined in ISO/IEC 15693-3.
Only Option 0 (Option flag is not set) is supported.
8.1.2.10
Get system information
As defined in ISO/IEC 15693-3.
The IC returns number of blocks= 48 blocks, because it comprises the same digital part as
I•CODE SLI-S.
The TAG type of the SL2 ICS50/SL2 ICS51 is “03h”.
8.1.3 Custom commands
The Manufacturer code of NXP Semiconductors is defined in ISO/IEC 7816-6A1. It has
the value “04h”.
For the structure of custom commands please refer to ISO/IEC 15693-3.
8.1.3.1
Get random number
Command Code = B2h
The Get Random Number command is required to receive a random number from the
label IC. The passwords that will be transmitted with the Set Password command have to
be calculated with the Password and the Random Number (see Section 8.1.3.2 “Set
password”).
The different passwords are addressed with the Password Identifier.
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
10 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8 bits
Table 5.
SOF
Table 6.
Request format
Flags
Get Random
Number
IC Mfg
code
UID
CRC16
8 bits
8 bits
8 bits
64 bits
16 bits
Response format when Error_flag is set
SOF
Table 7.
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
SOF
8.1.3.2
EOF
Flags
Random Number CRC16
8 bits
16 bits
EOF
16 bits
Set password
Command Code = B3h
With the Set Password command the different Passwords can be transmitted to the Label
to get access to the different protected functionalities on the following commands. The Set
Password command has to be executed just once for the related passwords if the label is
powered.
Remark: The Set Password command can only be executed in addressed or selected
mode except of the Privacy Password.
The XOR Password has to be calculated with the password and two times the received
random number from the last Get Random Number command:
XOR_Password[31:0] = Password[31:0] XOR {Random_Number[15:0],
Random_Number[15:0]}
The different passwords are addressed with the Password Identifier.
8 bits
Table 8.
SOF
Table 9.
Request format
Flags
Set
IC Mfg
Password code
UID
Identifier
Password
Identifier
XOR
CRC16
Passwo
rd
8 bits
8 bits
64 bits
8 bits
32 bits
8 bits
16 bits
Password Identifier
Password Identifier
Password
04h
Privacy
08h
Destroy SLI- L
10h
EAS
136430
Product data sheet
EOF
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
11 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
Table 10.
Response format when Error_flag is set
SOF
Table 11.
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
SOF
Flags
CRC16
8 bits
16 bits
EOF
Remark: If the IC receives an invalid password, it will not execute any following command
until a Power-On Reset (RF Reset) is executed.
8.1.3.3
Write password
Command Code = B4h
With the Write Password command a new password will be written into the related
memory, if the related old password has already been transmitted with a Set Password
command before and the addressed password is not locked (see Section 8.1.3.4 “Lock
password”).
Remark: The Write Password command can only be executed in addressed or selected
mode. The new password takes effect immediately which means that the new password
has to be transmitted with the Set Password command to get access to protected
blocks/pages.
The different passwords are addressed with the Password Identifier.
8 bits
Table 12.
SOF
Table 13.
Request format
Flags
Write
Passwor
d
IC Mfg
code
UID
Password
Identifier
Password CRC16
8 bits
8 bits
8 bits
64 bits
8 bits
32 bits
Password
04h
Privacy
08h
Destroy SLI- L
10h
EAS
SOF
Table 15.
SOF
Response format when Error_flag is set
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
Flags
CRC16
8 bits
16 bits
136430
Product data sheet
16 bits
Password Identifier
Password Identifier
Table 14.
EOF
EOF
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
12 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.1.3.4
Lock password
Command Code = B5h
With the Lock Password command the addressed password will be locked, if the related
password has already been transmitted with a Set Password command before. A locked
password can not be changed any longer.
The different passwords are addressed with the Password Identifier.
8 bits
Table 16.
SOF
Table 17.
Request format
Flags
Lock
IC Mfg
Password code
UID
Password CRC16
Identifier
8 bits
8 bits
64 bits
8 bits
8 bits
Password
04h
Privacy
08h
Destroy SLI- L
10h
EAS
SOF
Table 19.
SOF
Response format when Error_flag is set
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
Flags
CRC16
8 bits
16 bits
136430
Product data sheet
16 bits
Password Identifier
Password Identifier
Table 18.
EOF
EOF
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
13 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.1.3.5
Destroy SLI- L
Command Code = B9h
With the Destroy SLI- L command the I•CODE SLI-L/I•CODE SLI-L HC Label IC can be
destroyed if the Destroy SLI- L password has been transmitted before. This command is
irreversible and the I•CODE SLI-L/I•CODE SLI-L HC will never respond to any command
again (ISO commands).
Remark: The Destroy SLI- L can only be executed in addressed or selected mode.
8 bits
Table 20.
SOF
Table 21.
Request format
Flags
Destroy
SLI- L
IC Mfg
code
UID
CRC16
8 bits
8 bits
8 bits
64 bits
16 bits
Response format when Error_flag is set
SOF
Table 22.
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
SOF
8.1.3.6
EOF
Flags
CRC16
8 bits
16 bits
EOF
Enable privacy
Command Code = BAh
With the Enable Privacy command the I•CODE SLI-L/I•CODE SLI-L HC Label IC can be
set into the Privacy mode. The I•CODE SLI-L/I•CODE SLI-L HC will not respond to any
command except Get Random Number and Set Password.
To get out of the Privacy Status the valid Privacy password has to be transmitted to the IC
with the Set Password command.
8 bits
Table 23.
SOF
Table 24.
SOF
Table 25.
SOF
Request format
Flags
Enable
Privacy
IC Mfg
code
UID
8 bits
8 bits
8 bits
64 bits optional 16 bits
EOF
Response format when Error_flag is set
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
Flags
CRC16
8 bits
16 bits
136430
Product data sheet
CRC16
EOF
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
14 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.1.3.7
Inventory page read
Command Code = B0h
When receiving the Inventory Page Read request, the I•CODE SLI-L/I•CODE SLI-L HC IC
performs the same as in the anti-collision sequence, with the difference that instead of the
UID and the DSFID the requested memory content is re-transmitted from the
I•CODE SLI-L/I•CODE SLI-L HC IC.
If an error is detected the I•CODE SLI-L/I•CODE SLI-L HC IC remains silent.
If the Option flag is set to 0 n pages of data including page protection status (password
protection condition) are re-transmitted. If the option flag is set to 1 n pages (4 blocks =
16 byte) of data including page protection status (password protection condition) and the
part of the UID which is not part of the mask are re-transmitted.
The request contains:
•
•
•
•
•
•
•
•
•
Table 26.
SOF
Flags
Inventory Page Read command code
IC Manufacturer code
AFI (if the AFI flag is set)
Mask length
Mask value (if mask length > 0)
First page number to be read
Number of pages to be read
CRC 16
8 bits
Request format
Flags
Inventory
Read
IC Mfg
code
Optional Mask
AFI
Length
Mask
Value
8 bits
8 bits
8 bits
8 bits
0 to 64 bits 8 bits
8 bits
First Page
Number
Number of CRC16
Pages
8 bits
EOF
16 bits
The Inventory_flag must be set to 1.
The meaning of flags 5 to 8 is according to table 5 in ISO/IEC 15693-3.
The number of pages in the request is one less than the number of pages that the
I•CODE SLI-L/I•CODE SLI-L HC IC returns in its response.
If the Option flag in the request is set to 0 the response contains:
Table 27.
SOF
Response format
Flags
Data
CRC16
8 bits
Page status & data
16 bits
EOF
Repeated as needed
The I•CODE SLI-L/I•CODE SLI-L HC IC reads the requested block(s) including page
protection status and sends back their value in the response. The mechanism and timing
of the Inventory Page Read command performs the same as at the Inventory command
which is described in Clause 8 of ISO/IEC 15693-3.
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
15 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
The requested page(s) are transmitted in the following format and repeated as necessary
(depending on number of pages):
Table 28.
Page Protection Status byte
Page Protection Status byte
Block data
00h:
OK
16 byte page data content
0Fh:
ERROR
no data
If the Option flag in the request is set to 1 the response contains:
Table 29.
SOF
Response format
Flags
Rest of UID which is not part of
the mask and slot number
Data
CRC16
8 bits
0 to 64 bit
Page status & data
16 bits
Multiple of 8 bits
Repeated as needed
EOF
The I•CODE SLI-L/I•CODE SLI-L HC IC reads the requested page(s) including page
protection status and sends back their value in the response. Additionally the bytes of the
UID, which are not parts of the mask and the slot number in case of 16 slots, are returned.
Instead of a padding with zeros up to the next byte boundary the corresponding bits of the
UID are returned. The mechanism and timing of the Inventory Page Read command
perform the same as at the Inventory command which is described in Clause 8 of
ISO/IEC 15693-3.
The requested page(s) are transmitted in the following format and repeated as necessary
(depending on number of pages):
Table 30.
Page Protection Status byte
Page Protection Status Byte
Block Data
00h:
OK
16 byte page data content
0Fh:
ERROR
no data
Remark: The number of bits of the re-transmitted UID can be calculated as follows:
• 16 slots:
– 64 to 4 - mask length rounded up to the next byte boundary
• 1 slot:
–
64 - mask length rounded up to the next byte boundary
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
16 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
Remark: If the sum of first page number and number of pages exceeds the total available
number of user pages the number of transmitted pages is less than the requested number
of pages, which means that the last returned page is the highest available user page,
followed by the 16-bit CRC and the EOF.
• Example:
– mask length = 30
• Returned:
– 64 to 4 – 30 = 30 gives 4 bytes
Table 31.
Byte 0
Example
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
Byte 6
mask value incl. padding with zeros
UID
zeros transmitted by
Interrogator
returned value
8.1.3.8
Byte 7
transmitted by
I•CODE SLI-L/I•CODE
SLI-L HC IC
Fast inventory page read
Command Code = B1h
When receiving the Fast Inventory Page Read command the
I•CODE SLI-L/I•CODE SLI-L HC IC behaves the same as in the Inventory Page Read
command with the following exceptions:
The data rate in the direction I•CODE SLI-L/I•CODE SLI-L HC IC to the interrogator is
twice as defined in ISO/IEC 15693-3 depending on the datarate_flag 53 kbit (high data
rate) or 13 kbit (low data rate).
The datarate from the interrogator to the I•CODE SLI-L/I•CODE SLI-L HC IC and the time
between the rising edge of the EOF from the interrogator to the
I•CODE SLI-L/I•CODE SLI-L HC IC remain unchanged (stay the same as defined in
ISO/IEC 15693-3).
In the direction I•CODE SLI-L/I•CODE SLI-L HC IC to the interrogator only the single
subcarrier mode is supported.
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
17 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.1.3.9
Set EAS
Command Code = A2h
This command enables the EAS mode if the EAS mode is not locked. If the EAS mode is
password protected the EAS password has to be transmitted before with the Set
Password command.
8 bits
Table 32.
Request format
SOF
Table 33.
Flags
Set EAS
IC Mfg code
UID
CRC16
8 bits
8 bits
8 bits
64 bits
optional
16 bits
Response format when Error_flag is set
SOF
Table 34.
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
SOF
8.1.3.10
EOF
Flags
CRC16
8 bits
16 bits
EOF
Reset EAS
Command Code = A3h
This command disables the EAS mode if the EAS mode is not locked. If the EAS mode is
password protected the EAS password has to be transmitted before with the Set
Password command.
8 bits
Table 35.
SOF
Table 36.
SOF
Table 37.
SOF
Request format
Flags
Reset EAS IC Mfg code
UID
CRC16
8 bits
8 bits
64 bits
optional
16 bits
8 bits
Response format when Error_flag is set
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
Flags
CRC16
8 bits
16 bits
136430
Product data sheet
EOF
EOF
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
18 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.1.3.11 Lock EAS
Command Code = A4h
This command locks the current state of the EAS mode and the EAS ID. If the EAS mode
is password protected the EAS password has to be transmitted before with the Set
Password command.
8 bits
Table 38.
Request format
SOF
Table 39.
Lock EAS
IC Mfg code
UID
CRC16
8 bits
8 bits
8 bits
64 bits
optional
16 bits
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
SOF
8.1.3.12
EOF
Response format when Error_flag is set
SOF
Table 40.
Flags
Flags
CRC16
8 bits
16 bits
EOF
EAS Alarm
Command Code = A5h
The EAS Alarm command can be used in the following three configurations:
• Option flag is set to 0:
EAS ID Mask length and EAS ID value shall not be transmitted
If the EAS mode is set the EAS response is returned from the
I•CODE SLI-L/I•CODE SLI-L HC IC. This configuration is compliant to the EAS
command of the I•CODE SLI-L/I•CODE SLI-L HC IC.
• Option flag is set to 1:
Within the command the EAS ID Mask Length has to be transmitted to identify how
many bits of the following EAS ID value are valid (multiple of 8-bit). Only that
I•CODE SLI-L/I•CODE SLI-L HC ICs will respond with the EAS response which have
stored the corresponding data in the EAS ID configuration (selective EAS) and if the
EAS Mode is set.
If the EAS ID Mask length is set to 0, the I•CODE SLI-L/I•CODE SLI-L HC IC will
answer with its EAS ID.
8 bits
Table 41.
SOF
Request format
Flags
EAS
Alarm
IC Mfg
code
UID
EAS ID Mask EAS ID Value
Length
CRC16 EOF
8 bits
8 bits
8 bits
64 bits 8 bits optional 0 to 16 bits
16 bits
optional
multiple of 8 bits
optional
If an error is detected the I•CODE SLI-L/I•CODE SLI-L HC IC remains silent.
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
19 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
Option flag is set to 0 or option flag is set to 1 and the EAS ID Mask Length is not equal 0:
Table 42.
Response format
SOF
Flags
EAS Sequence
CRC16
8 bits
256 bits
16 bits
EOF
EAS sequence (starting with the LSB, which is transmitted first; read from left to right):
11110100 11001101 01000110 00001110 10101011 11100101 00001001 11111110
00010111 10001101 00000001 00011100 01001011 10000001 10010010 01101110
01000001 01011011 01011001 01100001 11110110 11110101 11010001 00001101
10001111 00111001 10001011 01001000 10100101 01001110 11101100 11110111
Option flag is set to 1 and the EAS ID Mask Length is equal 0:
Table 43.
Response format
SOF
Flags
EAS ID Value
CRC16
8 bits
16 bits
16 bits
EOF
If the EAS mode is disabled (see Reset EAS command in Section 8.1.3.10 “Reset EAS”)
the I•CODE SLI-L/I•CODE SLI-L HC IC remains silent.
8.1.3.13
Password protect EAS
Command Code = A6h
This command enables the password protection for EAS if the EAS password has to be
transmitted before with the Set Password command.
8 bits
Table 44.
SOF
Table 45.
SOF
Table 46.
SOF
Request format
Flags
Password
Protect EAS
IC Mfg code
UID
CRC16
8 bits
8 bits
8 bits
64 bits
optional
16 bits
Response format when Error_flag is set
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
Flags
CRC16
8 bits
16 bits
136430
Product data sheet
EOF
EOF
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
20 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.1.3.14
Write EAS ID
Command Code = A7h
With the command Write EAS ID a new EAS Identifier is stored in the corresponding
configuration memory. If EAS is password protected (for Set and Reset EAS) the EAS
password has to be transmitted before with the Set Password command.
8 bits
Table 47.
Request format
SOF
Flags
Write
EAS
IC Mfg code
UID
EAS ID
value
CRC16
8 bits
8 bits
8 bits
64 bits
optional
16 bits
16 bits
Table 48.
SOF
Table 49.
EOF
Response format when Error_flag is set
Flags
Error code
CRC16
8 bits
8 bits
16 bits
EOF
Response format when Error_flag is NOT set
SOF
Flags
CRC16
8 bits
16 bits
EOF
8.2 Long range command
8.2.1 Long Range CMD
Command Code = 40h
The Long Range CMD command is designed to allow the use of the higher limits defined
in the ISO/TR 7003:1990. The bit and byte coding is the same as it is defined in EPC
Specification “13.56 MHz ISM Band Class 1 Radio Frequency (RF) Identification Tag
Interface Specification”.
To reduce the number of pulses the redundancy check is changed from an CRC8
calculation to a XOR of the transmitted parameters (Long Range CMD, Data Selector,
Number of Slots)
• Number of Slots:
– If the Data Selector is transmitted for EAS the label will ignore the received
Number of Slots parameter and will use always one Slot (like EAS Alarm
command, see Section 8.1.3.12 “EAS Alarm”). with EAS. For EAS typically 00h is
used as the value for Number of Slots to reduce the number of transmitted pulses.
– If the Data Selector is transmitted for UID or EPC the label will respond within one
of the transmitted Number of Slots on a pseudo random basis and will calculate a
new slot for a following command.
Labels, which have executed a Destroy EPC command before will not respond to this
command, if the Data Selector for EPC is transmitted.
8 bits
Table 50.
SSOF
Request format
Long Range
CMD
Data
Selector
Number of Slots
XOR
8 bits
8 bits
8 bits
8 bits
136430
Product data sheet
CEOF
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
21 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
Table 51.
Number of Slots
Number of Slots
Value
1
10h
4
20h
8
40h
16
80h
32
00h
64
01h
128
02h
256
04h
512
08h
Table 52.
Data Selector
Data
Selector
Value
Response
EAS
00h
LSB first
UID
01h
LSB of LS Byte first
Depending on Data Selector the Label ICs will respond with the requested data.
8 bits
Table 53.
RSOF
Table 54.
VCD
Response format
Requested Data
CRC16
Depending on Data Selector
16 bits
REOF
Long Range CMD
Long Range CMD
VICCs
Response 1
Response 2
Response 3
Timing
t1
t1
t1
Slot
Slot 0
Slot1
Comment
8 bits
Table 55.
No VICC response
Collision
Timing
Timing
Min.
Max.
Unit
t1
302.06 - 2.36
30206 + 2.36
µs
136430
Product data sheet
Slot2
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
22 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.3 Error handling
8.3.1 Transmission errors
According to ISO/IEC 15693 the Label IC will not respond if a transmission error (CRC,
bitcoding, bitcount, wrong framing) is detected and will silently wait for the next correct
received command.
8.3.2 Not supported commands or options
If the received command or option is not supported, the behaviour of the Label IC is
depending on the addressing mechanism.
8.3.2.1
Non addressed mode
The label IC remains silent.
8.3.2.2
Addressed or selected mode
The addressed or selected label IC responds with the error code “0Fh” (error with no
information given or error code is not supported).
If the Inventory flag or the protocol extension flag is set the label IC will not respond if the
command or option is not supported.
8.3.3 Parameter out of range
8.3.3.1
Read commands
If the sum of the first block number and the number of blocks exceeds the total available
number of user blocks, the number of transmitted blocks is less than the requested
number of blocks, which means that the last returned block is the highest available user
block, followed by the 16-bit CRC and the EOF.
8.3.3.2
Write and lock commands
If the address of a block to be written does not exist or a block to be written is locked the
behaviour of the Label IC is depending on the addressing mechanism.
8.3.3.3
Non addressed mode
The Label IC remains silent and aborts the command without writing anything.
8.3.3.4
Addressed or selected mode
The addressed or selected Label IC responds with the error code “0Fh” (error with no
information given or error code is not supported).
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
23 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.4 Data integrity
Following mechanisms are implemented in the contactless communication link between
interrogator and label to ensure very reliable data transmission:
•
•
•
•
16-bit CRC per block
Bit count checking
Bit coding to distinguish between “1”, “0” and no information
Channel monitoring (protocol sequence and bit stream analysis)
8.5 RF interface
The definition of the RF interface is according to the standard ISO/IEC 15693-2 and
ISO/IEC 15693-3.
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
24 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
9. Revision history
Table 56.
Revision history
Document ID
Release date
Data sheet status
136430
14 March 2007
Product data sheet
Modifications:
•
Supersedes
new
Inital version
136430
Product data sheet
Change notice
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
25 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
10. Legal information
10.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
10.2 Definitions
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
10.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of a NXP Semiconductors product can reasonably be expected to
result in personal injury, death or severe property or environmental damage.
NXP Semiconductors accepts no liability for inclusion and/or use of NXP
Semiconductors products in such equipment or applications and therefore
such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted or
construed as an offer to sell products that is open for acceptance or the grant,
conveyance or implication of any license under any copyrights, patents or
other industrial or intellectual property rights.
10.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
<Name> — is a trademark of NXP B.V. (replace by text inset t001tma<1nn>)
11. Contact information
For additional information, please visit: http://www.nxp.com
For sales office addresses, send an email to: [email protected]
136430
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 3.0 — 14 March 2007
26 of 28
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
12. Tables
Table 1:
Table 2:
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Table 28.
Quick reference data . . . . . . . . . . . . . . . . . . . . .4
Ordering information . . . . . . . . . . . . . . . . . . . . . .4
Memory Organization . . . . . . . . . . . . . . . . . . . . .7
Unique Identifier description . . . . . . . . . . . . . . . .8
Request format . . . . . . . . . . . . . . . . . . . . . . . . . 11
Response format when Error_flag is set. . . . . . 11
Response format when Error_flag is NOT set . 11
Request format . . . . . . . . . . . . . . . . . . . . . . . . . 11
Password Identifier . . . . . . . . . . . . . . . . . . . . . . 11
Response format when Error_flag is set. . . . . .12
Response format when Error_flag is NOT set .12
Request format . . . . . . . . . . . . . . . . . . . . . . . . .12
Password Identifier . . . . . . . . . . . . . . . . . . . . . .12
Response format when Error_flag is set. . . . . .12
Response format when Error_flag is NOT set .12
Request format . . . . . . . . . . . . . . . . . . . . . . . . .13
Password Identifier . . . . . . . . . . . . . . . . . . . . . .13
Response format when Error_flag is set. . . . . .13
Response format when Error_flag is NOT set .13
Request format . . . . . . . . . . . . . . . . . . . . . . . . .14
Response format when Error_flag is set. . . . . .14
Response format when Error_flag is NOT set .14
Request format . . . . . . . . . . . . . . . . . . . . . . . . .14
Response format when Error_flag is set. . . . . .14
Response format when Error_flag is NOT set .14
Request format . . . . . . . . . . . . . . . . . . . . . . . . .15
Response format . . . . . . . . . . . . . . . . . . . . . . .15
Page Protection Status byte . . . . . . . . . . . . . . .16
Table 29.
Table 30.
Table 31.
Table 32.
Table 33.
Table 34.
Table 35.
Table 36.
Table 37.
Table 38.
Table 39.
Table 40.
Table 41.
Table 42.
Table 43.
Table 44.
Table 45.
Table 46.
Table 47.
Table 48.
Table 49.
Table 50.
Table 51.
Table 52.
Table 53.
Table 54.
Table 55.
Table 56.
Response format . . . . . . . . . . . . . . . . . . . . . . . 16
Page Protection Status byte. . . . . . . . . . . . . . . 16
Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Request format . . . . . . . . . . . . . . . . . . . . . . . . 18
Response format when Error_flag is set . . . . . 18
Response format when Error_flag is NOT set . 18
Request format . . . . . . . . . . . . . . . . . . . . . . . . 18
Response format when Error_flag is set . . . . . 18
Response format when Error_flag is NOT set . 18
Request format . . . . . . . . . . . . . . . . . . . . . . . . 19
Response format when Error_flag is set . . . . . 19
Response format when Error_flag is NOT set . 19
Request format . . . . . . . . . . . . . . . . . . . . . . . . 19
Response format . . . . . . . . . . . . . . . . . . . . . . . 20
Response format . . . . . . . . . . . . . . . . . . . . . . . 20
Request format . . . . . . . . . . . . . . . . . . . . . . . . 20
Response format when Error_flag is set . . . . . 20
Response format when Error_flag is NOT set . 20
Request format . . . . . . . . . . . . . . . . . . . . . . . . 21
Response format when Error_flag is set . . . . . 21
Response format when Error_flag is NOT set . 21
Request format . . . . . . . . . . . . . . . . . . . . . . . . 21
Number of Slots . . . . . . . . . . . . . . . . . . . . . . . . 22
Data Selector . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Response format . . . . . . . . . . . . . . . . . . . . . . . 22
Long Range CMD . . . . . . . . . . . . . . . . . . . . . . 22
Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 25
13. Figures
Fig 1.
Block diagram of TAG IC . . . . . . . . . . . . . . . . . . . .5
14. Contents
1
1.1
1.2
1.3
2
2.1
2.2
2.3
3
4
General description . . . . . . . . . . . . . . . . . . . . . .
Anticollision. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contactless energy and data transfer. . . . . . . .
Security and privacy aspects . . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I•CODE SLI-L RF interface. . . . . . . . . . . . . . . .
EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security features. . . . . . . . . . . . . . . . . . . . . . . .
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick reference data . . . . . . . . . . . . . . . . . . . . .
1
1
1
2
3
3
3
3
3
3
5
6
7
7.1
7.2
7.2.1
7.2.2
7.3
8
8.1
Ordering information . . . . . . . . . . . . . . . . . . . .
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional description . . . . . . . . . . . . . . . . . . .
Block description . . . . . . . . . . . . . . . . . . . . . . .
Memory organization . . . . . . . . . . . . . . . . . . . .
Unique identifier . . . . . . . . . . . . . . . . . . . . . . . .
Configuration of delivered ICs . . . . . . . . . . . . .
Communication principle . . . . . . . . . . . . . . . . .
Command set . . . . . . . . . . . . . . . . . . . . . . . . . .
ISO 15693 command set . . . . . . . . . . . . . . . . .
4
5
6
6
6
8
8
9
9
9
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2007.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 14 March 2007
Document identifier: 136430
SL2 ICS50/SL2 ICS51
NXP Semiconductors
I•CODE SLI-L/I•CODE SLI-L HC
PUBLIC
8.1.1
Mandatory commands . . . . . . . . . . . . . . . . . . . 9
8.1.1.1
Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8.1.1.2
Stay quiet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8.1.2
Optional commands . . . . . . . . . . . . . . . . . . . . . 9
8.1.2.1
Read single block . . . . . . . . . . . . . . . . . . . . . . . 9
8.1.2.2
Write single block . . . . . . . . . . . . . . . . . . . . . . . 9
8.1.2.3
Lock block. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8.1.2.4
Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8.1.2.5
Reset to ready . . . . . . . . . . . . . . . . . . . . . . . . 10
8.1.2.6
Write AFI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8.1.2.7
Lock AFI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8.1.2.8
Write DSFID . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8.1.2.9
Lock DSFID . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8.1.2.10 Get system information. . . . . . . . . . . . . . . . . . 10
8.1.3
Custom commands. . . . . . . . . . . . . . . . . . . . . 10
8.1.3.1
Get random number . . . . . . . . . . . . . . . . . . . . 10
8.1.3.2
Set password . . . . . . . . . . . . . . . . . . . . . . . . . 11
8.1.3.3
Write password . . . . . . . . . . . . . . . . . . . . . . . . 12
8.1.3.4
Lock password . . . . . . . . . . . . . . . . . . . . . . . . 13
8.1.3.5
Destroy SLI- L. . . . . . . . . . . . . . . . . . . . . . . . . 14
8.1.3.6
Enable privacy . . . . . . . . . . . . . . . . . . . . . . . . 14
8.1.3.7
Inventory page read . . . . . . . . . . . . . . . . . . . . 15
8.1.3.8
. . . . . . . . . . . . . . . . Fast inventory page read 17
8.1.3.9
Set EAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.1.3.10 Reset EAS . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.1.3.11 Lock EAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8.1.3.12 EAS Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8.1.3.13 Password protect EAS . . . . . . . . . . . . . . . . . . 20
8.1.3.14 Write EAS ID. . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.2
Long range command. . . . . . . . . . . . . . . . . . . 21
8.2.1
Long Range CMD . . . . . . . . . . . . . . . . . . . . . . 21
8.3
Error handling . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.3.1
Transmission errors . . . . . . . . . . . . . . . . . . . . 23
8.3.2
Not supported commands or options . . . . . . . 23
8.3.2.1
Non addressed mode . . . . . . . . . . . . . . . . . . . 23
8.3.2.2
Addressed or selected mode . . . . . . . . . . . . . 23
8.3.3
Parameter out of range. . . . . . . . . . . . . . . . . . 23
8.3.3.1
. . . . . . . . . . . . . . . . . . . . . . .Read commands 23
8.3.3.2
Write and lock commands . . . . . . . . . . . . . . . 23
8.3.3.3
Non addressed mode . . . . . . . . . . . . . . . . . . . 23
8.3.3.4
Addressed or selected mode . . . . . . . . . . . . . 23
8.4
. . . . . . . . . . . . . . . . . . . . . . . . . .Data integrity 24
8.5
. . . . . . . . . . . . . . . . . . . . . . . . . . RF interface 24
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 25
10
Legal information. . . . . . . . . . . . . . . . . . . . . . . 26
10.1
Data sheet status . . . . . . . . . . . . . . . . . . . . . . 26
10.2
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.3
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.4
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 26
11
Contact information. . . . . . . . . . . . . . . . . . . . . 26
12
13
14
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2007.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 14 March 2007
Document identifier: 136430