an1932

Application Note 1932
ISL28023 Precision Digital Power Monitor
Evaluation Kit User Guide
Introduction
ISL28023 Generic Board (ISL28023EVAL1Z)
The Precision Digital Power Monitor (DPM) Evaluation Kit is a
three evaluation board design that demonstrates the
functionality of the ISL28023. The ISL28023 is an IC with a
16-bit Analog-to-Digital Converter (ADC), an 8-bit
Digital-to-Analog Converter (DAC), and analog comparators
that monitors for undervoltage, overvoltage and overcurrent
conditions. The IC is serially controlled through an I2C bus. The
device abides by the PMBus standards.
The DPM Evaluation Kit is accompanied by a graphical user
interface (GUI) that allows the user to configure ISL28023 for
monitoring bus voltage and current in a specific application.
The GUI has a data save feature allowing the transfer of
measurement data to other software application for analysis.
The ISL28023 DPM Evaluation Kit consists of three boards; a
USB dongle, a generic ISL28023EVAL1Z board and an
ISL28023EVAL2Z demonstration board.
The generic ISL28023 board is a nonconfigured ISL28023 that
connects the analog inputs to the outside world. The board
allows a user to build a system that requires voltage, current or
power monitoring around the ISL28023. The analog inputs
(VINP, VINM and VBUS) of the ISL28023 accept input voltages
ranging from 0V to 60V. The ISL28023 allows the user to
uniquely configure the slave address via jumper selections.
The ISL28023 can be powered from a user defined source or
the 3.3V supply generated from the USB voltage. The
acceptable power supply voltage range for the ISL28023 is
from 3V to 5.5V. The external clock/interrupt pin is routed to
the outside world via a jumper selection. The maximum
measurable input differential (VINP - VINM) is ±80mV. The
differential voltage between the VINP and VINM pins can
withstand a magnitude of 60V. The differential supply
tolerance allows for the debugging of catastrophic circuit
events.
ISL28023 Demo Board (ISL28023EVAL2Z)
Dongle Evaluation Board
(ISLUSBPWRDONGLE1Z)
The dongle board mates from a PC to the ISL28023 via a
microcontroller. The microcontroller converts USB commands
sourced from the PC to an I2C header. The I2C pins (SCL and
SDA) are connected to the right angle header at the edge of
the board. The dongle board has a circuit that converts the USB
supply voltage to 3.3V. The 3.3V supply circuit has an
ISL28022 connected to monitor the current sourced by the
supply. Each circuit has been optimized to measure 100mA at
full scale. The 3.3V supply output and the SDA and SCL lines of
the I2C bus are routed to the right angle connector.
A peripheral circuit is required to demonstrate the functionality
of the ISL28023. The ISL28023 is paired up with a buck
regulator (ISL85415) and some sample loads to measure the
current and efficiency calculations of the regulator to the load.
The buck circuit allows the user to define a unique load that
connects to the regulator. The user can define the switching
frequency of the regulator by programming a resistor value
into the ISL23345 digital potentiometer. All features of the
ISL28023 are available.
Ordering Information
PART NUMBER
USB DONGLE
ISL28023EVAL1Z
GENERIC EVAL BOARD
DESCRIPTION
ISL28023EVAL1Z
Evaluation Board
ISL28023EVKIT1Z
Evaluation Kit
ISL28023EVAL2Z
GENERIC EVAL BOARD
FIGURE 1. ISL28023 EVALUATION KIT EVALUATION BOARDS
February 1, 2016
AN1932.3
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2014, 2016. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
Application Note 1932
Evaluation Package (Online
Order)
The Digital Power Monitor Generic Evaluation Kit contains the
following items:
• ISL28023 Demo Board (ISL28023EVAL2Z)
• ISL28023 Generic Board (ISL28023EVAL1Z)
• USB to I2C Dongle Board (ISLUSBPWRDONGLE1Z)
• Evaluation Software (Online)
Hardware Setup
- Connect the USB 2.0 cable to the PC first, and then to the
evaluation board
- The computer may ask about installing software for new
found hardware; select "Yes, this time only"
- On the following screen, it will ask about how to install
hardware. Select the recommended option (Installing from
CD) and follow the directions
- The USB is the only connector needed
Running the Software with the ISL28023
Generic Board
• User Guide
• ISL28023 Data sheet
Documentation for individual device can be found in the
following link:
http://www.intersil.com/products/ISL28023
System Requirements
• Windows 98/NT/2000/XP/VISTA/WIN7/Win8
• Available USB Port
Software Installation
Download the latest Evaluation Board GUI (Graphical User
Interface) from the following link:
ISL28023EVKIT1Z, ISL28025EVKIT1Z Evaluation Kit Software
Installing the Software
From the link supplied in the previous section, download and run
the executable file to start installing the GUI. The user will be
greeted by the screen shown in Figure 2. Continue through the
installer and read the instructions. The PC and PCB should not be
connected via the USB port until after the installation has
completed.
To run the program, go to the "Start" menu and choose the
ISL28023setup folder, and then choose the
ISL28023GenEvalSoftwareSetup icon. Once clicked, the demo
software window should appear as illustrated in Figure 3.
Enable communication between the evaluation board and the
computer by pressing the "Connect to Device" button at the
bottom right of the software window. If connection is successful,
the text on the button will be red and read "Disconnect Device" as
shown in Figure 3. Otherwise, the button text will not change.
The evaluation program controls and measures an ISL28023
device on a single I2C/SMBus. The main software window
displays one site.
DATA COLLECTING
To start collecting data, press the “Start Data Collecting” button
located to the left of the “Connect to Device” button at the
bottom of the screen. Once pressed, the color of the text and
verbiage of the button will change to “Stop Data Collecting “. The
defaults state of the software reads each DPM for shunt and bus
voltages. To change the read settings of the DPM, toggle the
check box/label next to each numerical read out. The back light
of the display will toggle between yellow and gray. A back light of
yellow means a channel is enabled. A change in the functionality
of the DPM will change the mode value for the respective
channel. The mode of each DPM is displayed in the lower left
hand corner of each channel's display.
FIGURE 2. INSTALLATION WELCOME SCREEN
Submit Document Feedback
2
AN1932.3
February 1, 2016
Application Note 1932
FIGURE 3. MAIN WINDOW OF THE ISL28023 GENERIC USER INTERFACE (GUI) CONNECTED TO THE ISL28023 GENERIC BOARD
DPM MEASUREMENT FUNCTIONALITY
LOOP DELAY
Enabling the current functional block on the DPM interface
requires the user to enter a shunt resistor value. The entered
value is stored in the DPM calibration register and is used to
calculate the current or power depending on the enabled check
box. Figure 4 illustrates the dialog box that requests the shunt
resistor value when current functionality is enabled.
The loop delay field in the lower right corner of the GUI allows the
user to program a delay between measurements. When the
ISL28023 is programmed to fast acquisition times, the screen is
updating quickly such that the user cannot read the
measurements that is taken by the ISL28023. The loop delay
field inserts a time delay after each measurement. Allowing for a
time delay makes the measurements readable.
SINGLE MEASUREMENT CONTROL
Pressing the Meas Once button on the main panel will measure
each enabled individual channel once.
THRESHOLD AND AUXILIARY CONTROLS
FIGURE 4. DIALOG BOX THAT ALLOWS THE USER TO ENTER THE
SENSE RESISTOR VALUE INTO THE ISL28023 DEVICE
Choose the Threshold selection under the ISL28023 drop down
menu that invokes the Auxiliary Control dialog box. The dialog
box allows the user to configure the threshold detectors of the
ISL28023 chip. Figure 5 shows the Auxiliary Controls Dialog Box.
ADC TIMING AND INTERNAL AVERAGE CONTROLS
The ADC Timing is the acquisition time of the ADC for the
channel. The acquisition timing selection of a channel is located
to the right of the channel’s measurement display in Figure 3.
The user can select ADC acquisition times ranging from 64µs to
2.05ms for each of the four channels shown in Figure 3.
The user adjusts the number of internal averages the ISL28023
makes before reporting out a value. The ISL28023 internal
averages can be programmed from a single measurement to
4096 measurements.
Submit Document Feedback
3
AN1932.3
February 1, 2016
Application Note 1932
FIGURE 6. The SMB ALERT CONFIGURATION WINDOW
FIGURE 5. THE WINDOW THAT CONTROLS THE ISL28023
COMPARATORS
The threshold levels of the analog comparators for the
overvoltage (OV), undervoltage (UV) and overcurrent conditions
(OC) are created from three 6-bit DACs. The DACs have voltage
ranges. There are two voltage ranges for the OC comparator and
six for the OV/UV comparators. The analog comparators can be
enabled and disabled by checking the enable check boxes.
Depending on the voltage range selected, the voltage range for
each threshold is stated above and below each input box.
The OC analog detector detection polarity can be set via checking
the "Reverse Current Direction?" check box.
The OV detector can be converted to a temperature threshold
detector by checking the "Temperature Detect?" check box.
SMBALERT
Choose the SMB Alert selection under the ISL28023 drop down
menu. A window similar to the Figure 6 will appear.
The outputs of the threshold comparators feed into the SMB Alert
control window. The comparator output can be routed to the
SMBALERT pins of the device via checking the respective
feed-through check box.
The default state of each comparator connects to a digital timing
filter and mask circuitry. All three comparators feed into an OR
gate to determine the status of the SMBALERT pin.
The active state polarity can be selected by checking the invert
check box of the respective SMBALERT pin.
There is one digital filter per threshold comparator. Setting the
digital filter changes the behavior for both SMBALERT pins. The
digital filter filters out aberrant responses from the analog
comparators by way of fault longevity. The device allows the user
to choose between four fault timing windows before allowing a
fault to pass to the latch bit (D flip-flop).
The mask block allows the user to determine if the fault is
passed to the OR gate.
Each SMBALERT pin can be controlled independent of
comparator circuitry by checking the force interrupt pin.
The default state of the SMBALERT2 pin is disabled. This puts the
pin state to tri-state. The SMBALERT2 pin has push-pull output
stage while the SMBALERT1 is an open drain.
Submit Document Feedback
4
AN1932.3
February 1, 2016
Application Note 1932
MARGIN DAC
Choose the SMB Alert selection under the ISL28023 drop down
menu. A window similar to Figure 7 appears.
FIGURE 9. THE CURRENT PEAK DETECT WINDOW
FIGURE 7. MARGIN DAC CONTROL WINDOW
The default state of the margin DAC is off, causing the DAC
output pin to be in tri-state. Enabling the margin DAC feature
requires the DAC output and DAC check boxes to be checked.
The Margin DAC is an 8-bit DAC with eight voltage ranges that
half scale voltage ranges from 0.4V to 1.2V. The user can choose
the DAC range next to the DAC Half Scale label. The min and max
input for each range is stated above and below the input box.
The Apply button sets the DAC voltage to the input voltage value
without closing the window. The OK button does the same as the
Apply button but closes the window. The cancel button does not
apply the input voltage.
EXTERNAL CLOCK ENABLE
The ISL28023 can be synchronized to an external clock to reduce
measurement noise in a system. To configure and enable the
external clock feature choose the EXTCLK selection in the
ISL28023 drop down menu. A dialog box, illustrated in Figure 8,
will appear allowing the user to enable the external clock feature.
The current peak detect feature reports the min and max reading
of a single sample. For example, suppose the settings for the
Vshunt input has an acquisition time of 64µs and an internal
average of 4096. The sense resistor has been digitized, such that
it enables current measurements. If the measure once button
has been pressed, the device will perform 4096 averages and
place the average value in the current register. With the current
peak detect enabled, the maximum and the minimum current
readings from the 4096 measurements are placed in the current
peak register and displayed in the window. If the meas once
button is pressed again, the Max/Min readings will reflect the
Max/Min readings for 8192 measurements. The Max/Min will
reflect the Max/Min current for all readings since the registers
have been cleared last.
EXTERNAL TEMPERATURE SENSOR
The external temperature sensor is a feature that measures the
temperature remotely from the DPM by connecting a diode to the
Aux shunt inputs. The DPM will squirt two currents to determine
the temperature of the diode.
The External Temperature sensor feature can be enabled by
checking the Ext Temp En check box in Figure 3 on page 3.
Checking the Ext Temp En check box will disable the internal
temperature sensor. The value from the external temperature
sensor is stored in the internal temperature register.
Upon enabling the external temperature sensor, an input box will
appear asking to null the temperature. The dialog box looks
similar to Figure 10.
FIGURE 8. THE EXTERNAL CLOCK WINDOW FOR THE ISL28023
The input bandwidth of the external clock pin is roughly 30MHz.
The external clock frequency can be divided to match the internal
system clock frequency of 500kHz. Choosing a clock division that
results in an internal clock frequency close to 500kHz will
guarantee ADC acquisition times similar to the default times.
PEAK CURRENT
Choose the Current Min/Max selection under the ISL28023 drop
down menu. A window similar to Figure 9 appears.
Submit Document Feedback
5
FIGURE 10. INPUT BOX THAT APPEARS WHEN ENABLING THE
EXTERNAL TEMPERATURE SENSOR
Diodes are not very good at measuring absolute temperature but
a very good at measuring temperature change.
If Yes is selected, the reading that is reported back is the
subtraction of the null temperature and the current temperature
that was measured.
AN1932.3
February 1, 2016
Application Note 1932
CONNECTING MULTIPLE ISL28023 EVALUATION
BOARDS TO A DONGLE
An ISL28023 design can have 55 devices connected on a single
I2C bus. The ISL28023 Evaluation Kit allows the user to cascade
up to 54 ISL28023 Evaluation Boards. The dongle uses a slave
address (0x9E) for measuring the current and voltage of the 3.3V.
Figure 11 is a picture of the dongle board connected to multiple
ISL28023 evaluation boards.
Connect the Dongle board to the computer via a USB cable. Start
the ISL28023 evaluation kit demo hardware.
Connect the software to the Dongle by pressing the "Connect to
Device" button at the bottom right of the software window. If the
connection is successful, the text on the button will be red and
read "Disconnect Device". All buttons on the front panel of the
GUI will be enabled. The GUI should look similar to Figure 3 on
page 3. When the software connects to the microcontroller, the
software scans for all the acceptable ISL28023 slave addresses
to determine if the device is connected to the dongle.
Once connected, each device can be configured uniquely by
pressing the next button that envelops the main features of the
GUI. Figure 12 illustrates the button to push.
USB DONGLE
ISL28023EVAL1Z
GENERIC EVAL BOARD
SYSTEM VIEW
When multiple ISL28023 devices are connected to the dongle
board, a system view screen is available. The system view allows
the user to view all the ISL28023 devices as configured.
To enter the system view, select System under the View drop
down menu. The window in Figure 13 will appear while the main
GUI window will disappear.
The window will size to the number of ISL2803 devices
connected to the dongle.
Pressing the “Start Data Collecting” button will loop through all
sites and measure the configure parameters for each ISL28023
device.
Pressing the “Save Data” button will save data for all sites. See
“SAVING DATA” on page 8 for more detail.
Pressing the “Single Site View” button will restore the main GUI
view.
RESET THE DEVICE
Choosing the Reset selection under the ISL28023 drop down
menu will soft reset the ISL28023 and restore the device to the
default value. A soft reset will perform an auto calibration of the
offset for each of the four channels of the device.
ISL28023EVAL1Z
GENERIC EVAL BOARD
ISL28023EVAL1Z
GENERIC EVAL BOARD
FIGURE 11. PICTURES OF SEVERAL ISL28023 GENERIC BOARDS CONNECTED TO A DONGLE ENABLING SYSTEM VIEW
Submit Document Feedback
6
AN1932.3
February 1, 2016
Application Note 1932
BUTTON TO PRESS TO
GO TO NEXT SITE
FIGURE 12. ISL28023 SINGLE SITE VIEW ILLUSTRATES THE BUTTON TO GO TO THE NEXT DEVICE/SITE
FIGURE 13. SYSTEM VIEW FOR THE ISL28023 SOFTWARE
Submit Document Feedback
7
AN1932.3
February 1, 2016
Application Note 1932
USB SUPPLIES
The ISL28023 Demo Software allows a user to build their own
board to mate with the Dongle board. The final design of the third
party board may use the dongle generated 3.3V power supply.
The user can monitor the current draw from 3.3V supply by
selecting USB Supplies under the dongle drop down menu. The
dialog box in Figure 14 will appear once the USB Supplies are
selected.
FIGURE 16. THE DIALOG BOX THAT REQUESTS WHERE TO SAVE THE
DATA FILES
FIGURE 14. USB SUPPLY WINDOW OF THE 3.3V GENERATED SUPPLY
I2C TRANSACTION
The ISL28023 Demo Software allows a user to build their own
board to mate with the dongle board. The final design may have
an I2C device incorporated into the design. The I2C transaction
selection in the dongle drop down menu allows the user to send
read and write commands to I2C devices. Figure 15 is the dialog
box that appears when the I2C transaction is chosen under the
dongle drop down menu.
The file name entered in the dialog box is the base name for all
files saved. A unique named file is generated for each measured
parameter (VBUS, VSHUNT, Current, Power, etc...) across all
active devices. The software only saves data to a file for each
measured parameter selected. If a measured parameter is not
selected, then a file with the non-selected measured parameter
is not generated. For example, VAUX and VAUXSHUNT are files
that would not be generated for the configuration of the DPM
window shown in Figure 3 on page 3.
All saved files are comma delimited. The naming convention of
the file is< base name>_<measured parameter>_dataset. The
base name is the file name entered in the save dialog box. The
measured parameter names are VBUS, VSHUNT, current and
power, etc.
Upon completion of the save dialog box, an input box (Figure 17)
asks for the number of points to be saved per site if the GUI is in
the Single Site Mode. Otherwise, the software will save the same
number of points for all sites in the System mode.
FIGURE 15. THE I2C TRANSACTION WINDOW
SAVING DATA
The DPM software allows the user to store a set number of points
of data. Go to the menu bar of the ISL28023 DPM Demo
Software window and choose File --> Save Data. Choosing the
Save Data option will open a dialog box asking for the filename
and directory of the save path. Figure 16 is an illustration of the
dialog box.
FIGURE 17. THE DIALOG BOX THAT ASKS THE USER TO ENTER THE
NUMBER OF DATA POINTS TO SAVE
SAVING AND LOADING THE CONFIGURATION FILES
The software allows the user to save and load the configuration
of each of the devices. To load or save a configuration, select
Load Config or Save Config under the File drop down menu. A
window will appear similar to Figure 16 that will ask for directory
information of the file to save or load.
Pressing the OK button with a valid numerical entry will begin
data collection. The numerical values change on the main
window while the data is being recorded. The completion of data
collection will commence when all of the active measurement
numbers cease to change.
The settings of all channels should be finalized prior to invoking
the Save Data feature. The user has the option of uniquely
naming each channel and having the channel name passed to
the column name of each respective data file. Changing the field
named "Channel Name" in Figure 3 on page 3 will change the
name of the column data.
Submit Document Feedback
8
AN1932.3
February 1, 2016
Application Note 1932
Running the Software with the ISL28023
Demo Board
All the controls and features discussed in the ISL28023 generic
board software are available to the user in the Demo software.
Connect and power the Demo board to the dongle board as
shown in Figure 18. Either use a power supply or a battery pack
to supply power to the Demo board. The Demo board can accept
voltages from 4.5V to 36V.
The ISL28023 Demo board connects the ISL28023 to a buck
regulator (ISL85415) and some resistive loads.
The board is properly powered by the battery pack with the most
negative voltage connected to the left of the VIN connector at the
top of the ISL28023 Demo board. This is illustrated in Figure 18.
Once properly powered, launch the ISL28023 software. The
same software used to control the ISL28023 generic board.
Press the "Connect To Device" button. The software will scan all
allowable slave addresses and determine the type of board
connected to the dongle. If the demo board is successfully
connected to the dongle, the window in Figure 19 appears.
The current going into the regulator is monitored by the Vshunt
inputs (Vinp, Vinm) and a shunt resistor of 0.02Ω(R20). The
VauxShunt inputs (Aux_P, Aux_N) are connected across a 0.02Ω
shunt resistor (R12). The VauxShunt channel measures the
current going to the load. The Vaux input measures the regulated
voltage at the load. The Vbus input measures the voltage applied
at VIN terminator. The current and power displays represent the
current and power being sourced to the regulator and load.
Press the "ON" button in the lower right hand corner to turn on
the ISL85415. The Vbus, Vshunt, Current, Power, Vaux channels
will turn on if they are not currently active.
The screen is the same as the ISL28023 generic evaluation
software plus the controls for the demo board. The Demo
Controls are illustrated as the ISL85415 group box in Figure 19.
ISL28023 DEMO BOARD
ISL28023EVAL2Z
DONGLE BOARD
FIGURE 18. THE ISL28023 DEMO CONNECTED TO THE DONGLE BOARD AND A BATTERY PACK
FIGURE 19. THE CONFIGURATION SCREEN FOR THE ISL28023 DEMO SOFTWARE
Submit Document Feedback
9
AN1932.3
February 1, 2016
Application Note 1932
Setting the Regulated Output Voltage
Enabling Efficiency Readings
Press the "Set Reg V" will launch the margin DAC window. The
margin DAC is connected to R15 or the Rg resistor of the
ISL85415 feedback. Equation 1 determines the regulated output
voltage.
By measuring the power going into the ISL85415 regulator and
calculating the power going to the load, the efficiency can be
calculated as shown in Equation 2, the efficiency equation used
in the ISL28023 Demo Software.
R 16
V OUT = 0.6 +  0.6 – DAC_OUT   ---------R 15
P LOAD
 = ----------------------  100
P TOTAL
(EQ. 1)
Where the reference voltage for the ISL85415 is 0.6V. The value
of R16 is the 120kΩ. The value of R15 is 20.5kΩ. The ISL85415 is
in a gain of 5.8537. The DAC_OUT is the voltage sourced from the
margin DAC. The output voltage will only work properly if the
output buffer and the DAC are enabled.
Setting the Switching Frequency
Press the "Set Freq" button to adjust the ISL23345, digitally
controlled potentiometer, which connects to the frequency select,
FS, pin of the ISL85415. The switching frequency of the regulator
will be altered causing the efficiency rating of the system to
change.
Changing the Shunt Resistor Values
Press the "Set Res Val" button changes the values used to
calculate system current and load current as well the efficiency
readings of the system.
(EQ. 2)
Note: At light loads, the current measurements will have errors due
to the temperature coefficient of the resistors. The resistors are
calibrated at moderate current levels. The magnitude of current
causes the resistors to heat up resulting in a shunt resistor value
change. The resistors installed on the demo board are 50ppm/°C
TC resistors with a power rating of 0.5W. Improving the temperature
coefficient of shunt resistors or increasing the power rating of the
resistors will limit the resistor change due to current.
Note: The power supply that is connected to the demo board
should be able to source 1A of current. If the sourcing capabilities
of the power supply are less than 1A, the regulate buck voltage
may oscillate or become unstable under certain load conditions.
Remember: The current of the primary channel of the ISL28023
only measures the current delivered to the ISL85415 buck
regulator. The VIN connector sources current to both the
ISL85415 and the 3.3V regulator that is part of the ISL28023.
The regulator draws approximately 1mA.
Change the Load Values Connected to the
Regulator
If the jumper setting for the OUTPUT LOAD header is connected
between pins 1 and 2, the output of the regulator is connected to
a series of loads that are controlled by a port extender and a
series of ISL83699 switches. To connect a load to the regulator,
check the check box of the desired load.
Submit Document Feedback
10
AN1932.3
February 1, 2016
SALERT
SGND
MSTR_EN
PRIMARY
2
VINP
2
REG_DAC
VREG_IN
3
REG_DAC
C12
0.1UF
10
R12
10
R11
22
21
20
19
VINP
VINM
NC3
REG_OUT
I2CVCC
17
AUXP
A2
16
A1
15
A0
14
GND2
13
EPAD
25
UNNAMED_3_ISL28023_I1_AUXP
4
UNNAMED_3_ISL28023_I1_AUXM
5
UNNAMED_3_ISL28023_I1_AUXV
6
UNNAMED_3_ISL28023_I1_DACOUT
U1
isl28023
AUXM
SMBCLK
DAC_OUT
EXT_CLK
AUXV
10
1
VCC_SEL-1
2
VCC_SEL-2
3
VCC_SEL-3
I2CVCC
A2
A1
A0
0.1UF
GND1
3
C8
18
SMBALERT2
2
0.1UF VCC
VCC
NC1
SMBALERT1
R6
3P3V
SGND
UNNAMED_3_ISL28023_I1_VBUS
UNNAMED_3_ISL28023_I1_REGIN
UNNAMED_3_ISL28023_I1_VINP
UNNAMED_3_ISL28023_I1_VINM
NC2
1
OPEN
OPEN
23
VBUS
24
0.1UF
R5
0.1UF
C7
C5
VCC_EXT
2
SGND
DAC_OUT
R8
SMBALERT2
SALERT
SCL
3P3V
SGND
1
3
A0
2
4
5
6
1
3
A1
2
4
5
6
12
J3
DNP
10
3P3V
SGND
11
9
10
8
7
49.9
OPEN
C4
OPEN
SDA*
SCL*
SDA*
SCL*
I2CVCC_EXT
SGND
0
R4
R3
SCL*
SALERT
R1
D1
AUX
AUXV
3
SGND
R7
1
I2-1
2
I2-2
3
I2-3
UNNAMED_3_SMLED_I121_B
THIS IS THE OUTPUT FEMALE HEADER
1K
SDA
SCL
3P3V
10
SDA
SGND
R2
10
PWR_GND
1
UNNAMED_3_ISL28023_I1_EXTCLK
C1
PWR_GND
PWR_GND
3
SGND
SDA*
J2
1
3
5
DATE:
ENGINEER:
RELEASED BY:
DATE:
TITLE:
UPDATED BY:
DATE:
DRAWN BY:
Ryan Roderick
1 2
3 4
5 6
2
4
6
SALERT
SGND
MSTR_EN
DATE:
Ryan Roderick
ISL28023 Generic Design
3P3V
SGND
1
3
5
A2
2
4
6
SDA*
SCL*
TESTER
MASK#
PLEASE PUT SILK LABEL NEXT TO CONNECTOR
Th F b 06 14 43 40 2014
FIGURE 20. SCHEMATIC OF THE ISL28023EVAL1Z BOARD
FILENAME:
REV.
HRDWR ID
SHEET
2
A
2
Application Note 1932
AUX
VREG_OUT
C6
SGND
C2
10
AUXM
0.1UF
C9
11
AUXP
1
R10
10
SGND
2
REG_DAC
0.1UF
0
VBUS
3
C10
R9
VREG_IN
AUX
1
SGND
THIS IS THE INPUT MALE HEADER
PRIMARY
DAC_OUT
SGND
REG_IN
2
4
6
VINM
SMBDAT
1 2
3 4
5 6
1
C11
1
3
5
PRIMARY
0.1UF
J1
C3
Submit Document Feedback
SDA
SCL
3P3V
AN1932.3
February 1, 2016
Application Note 1932
ISL28023EVAL1Z Bill of Materials
MANUFACTURER PART
QTY
UNITS
ISL28023EVAL1ZREVAPCB
1
ea.
C2012X7R2A104K
6
ea.
C5, C6, C9, C10, C11, C12
CAP, SMD, 0805, 0.1µF, 100V, 10%, X7R, ROHS TDK
ECJ-2VB1E104K
2
ea.
C7, C8
CAP, SMD, 0805, 0.1µF, 25V,10%,X7R,ROHS
0
ea.
C1, C2, C3, C4
CAP, SMD, 0805, DNP-PLACE HOLDER, ROHS
1725669
4
ea.
AUX, PRIMARY, PWR_GND,
REG_DAC
CONN-TERMINAL BLK, TH, 3POS, 2.54mm,
20-30AWG, ROHS
PHOENIX CONTACT
65474-010LF
5
ea.
a) A0-PINS 5-3, A1-PINS 5-3,
A2-PINS 5-3;
CONN-MINI JUMPER, SHORTING, 2PIN, BLUE,
ROHS
FCI/BERG
65474-010LF
0
ea.
b) VCC_SEL-PINS 1-2,
I2CVCC_SEL-PINS 1-2.
CONN-MINI JUMPER, SHORTING, 2PIN, BLUE,
ROHS
FCI/BERG
67996-272HLF
3
ea.
A0, A1, A2
CONN-HEADER, 2x3, BRKAWY 2X36, 2.54mm,
VERTICAL, ROHS
BERG/FCI
68000-236HLF
2
ea.
VCC_SEL, I2CVCC_SEL
CONN-HEADER, 1x3, BREAKAWY 1x36,
2.54mm, ROHS
BERG/FCI
MTSW-150-22-G-D-215-RA
1
ea.
J1
CONN-HEADER, 2x25, 2.54mmPITCH, R/A,
1.13x1.43in, ROHS
SAMTEC
PPPC032LJBN-RC
1
ea.
J2
CONN-SOCKET, TH, 6P, 2x3, INSULATED, R/A,
2.54mm, ROHS
SULLINS
CMD17-21VYD/TR8
1
ea.
D1
LED,SMD, 0805, YELLOW/DIFF., 2V, 20mA,
4mcd, 585nm, ROHS
CHICAGO
MINIATURE
ISL28023FR60Z
1
ea.
U1
IC-PRECISION DIGITAL MONITOR, 24P, QFN,
ROHS
INTERSIL
ERA-6AEB102V
1
ea.
R1
RES, SMD, 0805,1k, 1/8W, 0.1%, MF, ROHS
PANASONIC
CR0805-8W-10R0FT
8
ea.
R2, R3, R5, R6, R8, R10, R11, R12 RES, SMD, 0805, 10Ω, 1/8W, 1%, TF, ROHS
VENKEL
RC0805JR-070RL
2
ea.
R7, R9
RES, SMD, 0805, 0Ω, 1/8W, TF, ROHS
YAGEO
MCR10EZHF49R9
1
ea.
R4
RES, SMD, 0805, 49.9Ω, 1/8W, 1%, TF, ROHS
ROHM
S-2261
1
ea.
Place assy in bag
BAG, STATIC, 4X6, ZIPLOC, ROHS
ULINE
LABEL-DATE CODE
1
ea.
AFFIX TO BACK OF PCB
LABEL-DATE CODE_LINE 1: YRWK/REV#, LINE 2: INTERSIL
BOM NAME
Submit Document Feedback
12
REFERENCE DESIGNATOR
DESCRIPTION
PWB-PCB, ISL28023EVAL1Z, REVA, ROHS
MANUFACTURER
IMAGINEERING INC
PANASONIC
AN1932.3
February 1, 2016
C15
RW0
SDA
SCL
12
SCL
10
9
0.1UF
1
2
3
21
20
19
NC3
REG_OUT
A2
16
A2
A1
15
A0
14
A1
A0
GND2
13
EPAD
25
4
UNNAMED_3_ISL28023_I1_AUXM
6
AUXM
DAC_OUT
U9
C17
isl28023
AUXV
EXT_CLK
5
12
R18
UNNAMED_3_ISL28023_I1_AUXP
33
SMBALERT2
22
17
AUXP
3
SMBALERT2
2AUXM
AGND
VINP
18
I2CVCC
11
2DAC_OUT
VINM
VCC
GND1
33
REG GAIN
ISL85415
VOUT
SCL
0.1UF
3P3V
SGND
SMBALERT2
SGND
OUT
3P3V
1
SGND
5
3P3V
1
SGND
5
3
A0
2
4
6
SALERT
SDA
SGND
3P3V
A1_D
NC1
2
EP
ADDR SEL FOR DCP+ PORT EXT
1
2
3
1
R17
SMBALERT2
PGND
7
EN
2AUXP
0.1UF
0.1UF
SMBALERT1
PHASE
8
PG
R16 120K
UNNAMED_3_ISL85400_I2_9
NC2
9
23
VOUT
10
9
VCC
UNNAMED_3_ISL28023_I1_REGIN
UNNAMED_3_ISL28023_I1_VINMUNNAMED_3_ISL28023_I1_REGOUT
10
VIN
C16
REG_IN
SGND
UNNAMED_3_ISL85400_I2_10
FB
BOOT
SGND
470PF
24
UNNAMED_3_ISL85400_I2_3
C22
AGND
SMBDAT
13
COMP
R15
6
100K
11
UNNAMED_3_ISL85400_I2_11
SYNC
20.5K
5
FS
1UF
3
TKSS
SGND
SGND
3P3V
A0_D
C20
SGND
A1_D
VBUS
C14
2AUXP
2AUXM
A2
8
AGND
SGND
0.020
12
UNNAMED_3_ISL85400_I2_1
C13
22UF
C9
0.020
R12
22UH
L1
R20
SGND
SMBCLK
0.033UF
C12
10UF
C10
10UF
C8
C7
22UF
OUT
2
R14
UNNAMED_3_SMCAP_I14_B
4
UNNAMED_3_CHOKE_I10_B
AGND
Application Note 1932
U1
2
1
VIN*
A0_D
1
C11 0.1UF
8
A0 A1
VIN*
AGND
0.1UF
11
VIN
2
C23
13
SDA
1
INPUT
RL2
U8
AGND
15
RL1
DNP
INPUT
0.1UF
UNNAMED_3_ISL23345_I37_RL1
14
33
3
13
UNNAMED_3_ISL23345_I37_RH2
C21
R13
RH2
RW2
R21
RW1
RL3
33
AGND
UNNAMED_3_ISL23345_I37_RH1
4
SGND
MSTR_EN
17
R19
RH1
5
AGND
2
4
6
18
ISL2345
RL0
1 2
3 4
5 6
3P3V
16
RW3
19
IN
21
RH3
UNNAMED_3_ISL23345_I37_RH0
20
OUT
EP
RH0
2
7
MSTR_EN
OUT
0.1UF
SGND
3P3V
OUT
6
VLOGIC VCC GND
2
4
6
C19
1 2
3 4
5 6
SALERT
J2
1
3
5
SCL
C18
1
3
5
SDA
SALERT
J1
SCL
IN
THIS IS THE OUTPUT FEMALE HEADER
SGND
0.1UF
SDA
BI
0.1UF
1
THIS IS THE INPUT MALE HEADER
7
Submit Document Feedback
FREQUENCY_SEL
3P3V
SALERT
SDA
SCL
OUT
SGND
DCP/PORT EXT HAVE THE SAME
BASE SLAVE ADDRESS =0XA0
DATE:
ENGINEER:
RELEASED BY:
DATE:
TITLE:
UPDATED BY:
DATE:
DRAWN BY:
3
3P3V
1
SGND
5
A1
2
4
6
3
A2
2
4
6
SDA
SCL
Ryan Roderick
Ryan Roderick
DATE:
ISL28023/ISL854015 Design
SDA
TESTER
SCL
MASK#
FIGURE 21. SCHEMATIC OF THE ISL28023EVAL2Z BOARD (1 OF 2)
HRDWR ID
REV.
AN1932.3
February 1, 2016
SDA
SCL
12
SCL
11
NOT_WC
NO1
17
6
GND
SGND
3
1MA
IO2
4
5MA
IO3
5
10MA
IO4
7
IO5
8
17
GND
IO1
NO1
15
R6
IO6
9
IO7
10
500MA
6.98K
3
16
68
3
5
16
AGND
COM2
4
IN12
NO2
2
0.5MA
COM2
NC2
COM1
NO2
NC2
5
AGND
50MA
100MA
300MA
NC1
1
COM1
NC1
1
15
R10
EPAD
0.5MA
V+
2
6
14
UNNAMED_2_ISL83699_I27_NO1
IO0
SGND
EPAD
6
17
EPAD
0.1UF
UNNAMED_2_ISL83699_I31_NO1
4
NO3
A0
A1
A2
16
1
UNNAMED_2_ISL83699_I27_NO3
15
14
MSTR_EN
IN
C3
3P3V
VSS
14
VDD
13
PCA9500
BI
IN
SDA
SGND
0.1UF
14
0.1UF
3P3V
IN
3P3V
V+
Submit Document Feedback
C6
C1
7
R11
IN12
50MA2
U2
NC3
9
NO3
NO4
UNNAMED_2_HEADERSINGLEROW_I52_IN1
10
AGND
SGND
0
NC1
15
3
5
16
14
6
GND
NC1
1
R4
NO2
NC2
NO1
UNNAMED_2_ISL83699_I33_NO1
15
COM1
3
COM2
22
4
5
U7 ISL83699
COM1
16
AGND
NO2
NC2
10
SGND
COM2
4
SGND
IN12
2
5MA
NO3
UNNAMED_2_ISL83699_I29_NO3
7
COM1
16
NO2
NC2
NC1
3
5
0.1UF
V+
3P3V
17
6
GND
UNNAMED_2_ISL83699_I35_NO1
1
SGND
EPAD
14
NO1
698
C4
0.1UF
V+
3P3V
R1
NO1
1
R8
U4 ISL83699
C2
15
0.1UF
UNNAMED_2_ISL83699_I29_NO1
15
17
3
2
IN34
100MA
EPAD
VOUT
12
12
IN34
17
OUTPUT
3P3V
COM4
NC4
13
6
2
11
GND
OUTPUT
R3
IN
13
COM4
1MA
C5
NO4
EPAD
1
NC4
Application Note 1932
AGND
1
8
AGND
33
UNNAMED_2_HEADERSINGLEROW_I50_IN1
9
IN
14
3P3V
11
COM3
NC3
V+
A1_D
IN
7
R7
8
AGND
3.48K
UNNAMED_2_ISL83699_I31_NO3
A0_D
IN
COM3
R9
9
348
11
COM2
13
NC3
COM3
8
AGND
NO4
NC4
COM4
12
4
IN34
IN12
IN12
2
10MA
2
AGND
AGND
NO3
UNNAMED_2_ISL83699_I35_NO3
7
R2
9
COM3
8
9
13
NO4
NC4
22
COM4
12
11
13
IN34
500MA
NO3
U6 ISL83699
UNNAMED_2_ISL83699_I33_NO3
7
NC3
COM3
8
DATE:
ENGINEER:
RELEASED BY:
DATE:
TITLE:
UPDATED BY:
DATE:
DRAWN BY:
R5
11
15
NC3
10
10
NO4
NC4
Ryan Roderick
ISL28023/ISL854015 Des
COM4
12
IN34
300MA
TESTER
10
MASK#
U3 ISL83699
DA
Ryan Roderick
U5 ISL83699
Fri Dec 06 13:34:52 2013
FIGURE 22. SCHEMATIC OF THE ISL28023EVAL2Z BOARD (2 OF 2)
FILENAME:
HRDWR ID
SHEET
3
AN1932.3
February 1, 2016
Application Note 1932
ISL28023EVAL2Z Bill of Materials
MANUFACTURER PART
QTY
UNITS
ISL28023EVAL2ZREVAPCB
1
ea.
GRM36X7R333K016AQ
1
ea.
ECJ-0EB1H471K
1
06035C104KAT2A
REFERENCE
DESIGNATOR
DESCRIPTION
MANUFACTURER
PWB-PCB, ISL28023EVAL2Z, REVA, ROHS
IMAGINEERING INC
C12
CAP, SMD, 0402, 33000pF, 16V, 10%, X7R,
ROHS
MURATA
ea.
C14
CAP, SMD, 0402, 470pF, 50V, 10%, X7R,
ROHS
PANASONIC
16
ea.
C1-C6, C11, C15-C23
CAP, SMD, 0603, 0.1µF, 50V, 10%, X7R,
ROHS
AVX
GRM188R61C105KA12D
1
ea.
C13
CAP, SMD, 0603, 1µF, 16V, 10%, X5R, ROHS MURATA
C1206C107M9PACTU
2
ea.
C7, C9
CAP, SMD, 1206, 100µF, 6.3V, 20%, X5R,
ROHS
TMK316B7106KL-TD
2
ea.
C8, C10
CAP, SMD, 1206, 10µF, 25V, 10%, X7R, ROHS TAIYO YUDEN
74408943220
1
ea.
L1
COIL-PWR INDUCTOR, SMD, 4.8mm, 22µH,
20%, 1.1A, ROHS
Wurth Electronics
1725656
2
ea.
INPUT, OUTPUT
CONN-TERMINAL BLK, TH, 2P, 6A, 125V,
20-30AWG, 2.54mm, ROHS
PHOENIX CONTACT
67996-272HLF
3
ea.
A0-A2
CONN-HEADER, 2x3, BRKAWY 2x36,
2.54mm, VERTICAL, ROHS
BERG/FCI
68000-236HLF
3
ea.
VOUT, ADDR0, ADDR1 CONN-HEADER, 1x3, BREAKAWY 1x36,
2.54mm, ROHS
BERG/FCI
MTSW-150-22-G-D-215-RA
1
ea.
J1
CONN-HEADER, 2x25, 2.54mm PITCH, R/A,
1.13x1.43in, ROHS
SAMTEC
PPPC032LJBN-RC
1
ea.
J2
CONN-SOCKET, TH, 6P, 2x3, INSULATED, R/A, SULLINS
2.54mm, ROHS
ISL23345TFRZ
1
ea.
U8
IC-100k LO VOLT. DIGITAL POTENTIOMETER,
20P, QFN, ROHS
INTERSIL
ISL28023FR60Z
1
ea.
U9
IC-PRECISION DIGITAL MONITOR, 24P, QFN,
ROHS
INTERSIL
ISL83699IRZ
5
ea.
U3-U7
IC-QUAD SPDT ANALOG SWITCH, 16P, QFN,
ROHS
INTERSIL
ISL85415FRZ
1
ea.
U1
IC-500mA BUCK REGULATOR, 12P, DFN, 3x4, INTERSIL
ROHS
PCA9500BS,118
1
ea.
U2
IC-8-BIT I2C I/O EXPANDER, 16P, HVQFN,
4X4, ROHS
0
ea.
R13
RESISTOR, SMD, 0603,0.1%, MF, DNP-PLACE
HOLDER
1
ea.
R14
RES, SMD, 0402, 100k, 1/16W, 1%, TF,
ROHS
2
ea.
R19, R21
RES, SMD, 0603, 0Ω, 1/10W, 1%, TF, ROHS
2
ea.
R17, R18
RES, SMD, 0603, 33Ω, 1/10W, 1%, TF, ROHS
1
ea.
R16
RES, SMD, 0603, 120k, 1/10W, 1%, TF,
ROHS
1
ea.
R15
RES, SMD, 0603, 20.5k, 1/10W, 1%, TF,
ROHS
1
ea.
R11
RES, SMD, 0805, 200Ω, 1/8W, 1%, TF, ROHS PANASONIC
1
ea.
R8
RES, SMD, 0805, 150Ω, 1/8W, 1%, TF, ROHS PANASONIC
1
ea.
R10
RES, SMD, 0805, 301Ω, 1/8W, 1%, TF, ROHS PANASONIC
ERJ2RKF1003
CRCW0603120KFKEA
Submit Document Feedback
15
KEMET
NXP SEMICONDUCTOR
PANASONIC
VISHAY/DALE
AN1932.3
February 1, 2016
Application Note 1932
ISL28023EVAL2Z Bill of Materials (Continued)
MANUFACTURER PART
REFERENCE
DESIGNATOR
QTY
UNITS
1
ea.
R3
RES, SMD, 1206, 0Ω, 1/4W, TF, ROHS
1
ea.
R9
RES, SMD,1206, 49.9Ω, 1/4W, 1%, TF, ROHS
CRCW251215R0FKEG
2
ea.
R1, R2
RES, SMD, 2512, 15Ω, 1W, 1%, TF, ROHS
VISHAY/DALE
CR2512-1W-220JT
2
ea.
R4, R5
RES, SMD, 2512, 22Ω, 1W, 5%, TF, ROHS
VENKEL
MCR50JZHJ330
1
ea.
R6
RES, SMD, 2010, 33Ω, 1/2W, 5%, TF, ROHS
ROHM
MCR50JZHJ220
1
ea.
R7
RES, SMD, 2010, 22Ω, 1/2W, 5%, TF, ROHS
ROHM
KRL1220E-M-R022-F-T5
2
ea.
R12, R20
RES-CURR.SENSE, SMD, 0805, 0.022Ω,
0.5W, 1%, 55ppm, ROHS
SUSUMU
65474-010LF
6
ea.
a) A0-PINS 1-3,
A1-PINS 5-3, A2-PINS
5-3, ADDR0 2-3,
ADDR1 2-3
CONN-MINI JUMPER, SHORTING, 2PIN, BLUE, FCI/BERG
ROHS
65474-010LF
0
ea.
b) OUTPUT 2-3
CONN-MINI JUMPER, SHORTING, 2PIN, BLUE, FCI/BERG
ROHS
212403-013
1
ea.
Place assy in bag
BAG, STATIC, 5x8, ZIPLOC, ROHS
LABEL-DATE CODE
1
ea.
AFFIX TO BACK OF PCB LABEL-DATE CODE_LINE 1: YRWK/REV#,
LINE 2: BOM NAME
Submit Document Feedback
16
CRCW1206-000Z
DESCRIPTION
MANUFACTURER
VISHAY
INTERSIL
INTERSIL
AN1932.3
February 1, 2016
Submit Document Feedback
R28
R27
R26 1K
1K
1K
3P3V
U9
UNNAMED_3_SMLED_I234_A
POL_PG
17
IN
OUT
OUT
3P3V_PG
IN
POL_SEL0
SDA
3P3V
7
REGIN
P2.0 18
8
VBUS
P2.1 17
2
4
6
2 1
4 3
6 5
1
3
5
PG/SALRT1
26
25
P1.1
P1.0
28
P0.6
P0.7
29
27
30
P1.7 19
MSTR_EN
UNIVERSAL6
PLACE AT RIGHT EDGE OF BOARD.
P2.2
RIGHT ANGLE FEMALE CONNECTOR
P2.3
C22
16
15
14
13
1K
12
9
UNNAMED_3_C8051F320_I232_RSTC2CK
UNNAMED_3_C8051F320_I232_P30
1UF
R24
1UF
P0.5
P1.6 20
VDD
UNNAMED_3_C8051F320_I232_DN
0.1UF
C20
31
D-
6
RST/C2CK
6
C21
SCL
OUT
P1.5 21
P2.4
USB_PWR
MOUNT
OUT
EN_3P3V
C8051F320
P2.5
0
D+
POL_SEL2
P1.4 22
U8
UNNAMED_3_C8051F320_I232_DP
P2.6
5
UNNAMED_3_SMRES_I231_A
GND
P2.7
0
MCU_PWR
P1.3 23
11
OUT
P0.0
10
1
4
1
2
P3.0/C2D
5
USB
4
P1.2 24
4
UNNAMED_3_SMRES_I230_A
R23
P0.1
3
R22
2
1
Application Note 1932
J1
2
3
3
P0.4
POL_SEL[0..2]
MSTR_EN
MOUNT
P0.3
P0.2
32
POL_SEL1
UNNAMED_3_C8051F320_I232_P06
R25
1K
OPEN
C24
OPEN
C23
3P3V
1
3
5
7
9
PGR
PGR
PGR
PGR
PGR
UNNAMED_3_HEADERDUALROW_I252_IN1
PGR
PGR
PGR
PGR
PGR
PROGRAM HEADER
2
4
6
8
10
UNNAMED_3_HEADERDUALROW_I250_IN1
R29
10K
DRAWN BY:
DATE:
ENGINEE
RELEASED BY:
DATE:
TITLE:
UPDATED BY:
DATE:
Ryan Roderick
Rya
Si L
TESTER
AN1932.3
February 1, 2016
FIGURE 23. ISLUSBPWRDONGLE1Z SCHEMATIC (1 OF 2)
U
3P3V
USB_PWR
18
C10
11
VBUS
7
0.1UF
C2
6
VOUT
2
12
10
VINP
VINN
3
SENSE/ADJ
NC
ENABLE
SS
PG
GND
EP
ISL80101IRAJZ
EXT_CLK/INT
4
5
R10
100K
R14
VOUT
UNNAMED_2_ISL28022QFN_I220_VINP
2
A0
1
A1
5
SMBCLK/SCL
4
SMBDAT/SDA
3
U4
11
IN
17
6
7
8
14
15
16
IN
SCL
SDA
EPAD
NC1
NC2
NC3
NC4
NC5
NC6
8
VIN
VIN
13
3.3
9
1
R8
C1
1UF
isl28022_QFN
10
Application Note 1932
U2
10K
ISL80101-3.3
VCC
9
0.1UF
1UF
C8
1UF
C6
EN_3P3V
IN
OUT
GND
Submit Document Feedback
3.3V CURRENT LIMIT
LIMIT IS 100mA
3.3V CURRENT
IS 100MA
5V TO 3.3V REG
5V TO
3.3V REG
SLAVE ADDR = OX9E/F
3P3V_PG
FIGURE 24. ISLUSBPWRDONGLE1Z SCHEMATIC (2 OF 2)
OUT
AN1932.3
February 1, 2016
Application Note 1932
ISLUSBPWRDONGLE1Z Bill of Materials
MANUFACTURER PART NUMBER
QTY
UNITS
REFERENCE DESIGNATOR
DESCRIPTION
MANUFACTURER
C2012X7R1E105K
5
ea
C1, C8, C10, C20, C22
CAP, SMD, 0805, 1.0µF, 25V, 10%,
X7R, ROHS
TDK
ECJ-2VB1E104K
3
ea
C2, C6, C21
CAP, SMD, 0805, 0.1µF, 25V, 10%,
X7R, ROHS
PANASONIC
67996-272HLF
1
ea
PGR
CONN-HEADER, 2X5, BRKAWY-2X36, BERG/FCI
2.54mm, ROHS
897-43-004-90-000
1
ea
J1
CONN-USB TYPE B, RECEPTACLE, PCB MILL-MAX
MOUNT, ROHS
SSQ-103-02-T-D-RA
1
ea
UNIVERSAL6
CONN-SOCKET STRIP, TH, 2X3,
2.54mm, TIN, R/A, ROHS
SAMTEC
CMD17-21VGC/TR8
1
ea
U9
LED, SMD, 0805, GREEN, CLEAR,
10mcd, 2.1V, 20mA, 570nm, ROHS
CHICAGO MINIATURE
C8051F320-GQ
1
ea
U8
IC-USB MICROCONTROLLER, 32P,
LQFP, 8-BIT, 25MIPS, ROHS
SILICON
LABORATORIES
ISL28022FRZ
1
ea
U4
IC-DIGITAL POWER MONITOR, 16P,
QFN, ROHS
INTERSIL
ISL80101IR33Z
1
ea
U2
IC-3.3V, 1A LDO REGULATOR, 10P,
DFN, 3X3, ROHS
INTERSIL
CR0603-10W-000T
2
ea
R22, R23
RES, SMD, 0603, 0Ω, 1/10W, TF,
ROHS
VENKEL
ERJ-3EKF1001V
2
ea
R24, R25
RES, SMD, 0603, 1k, 1/10W, 1%, TF, PANASONIC
ROHS
RK73H1JT1002F
2
ea
R14, R29
RES, SMD, 0603, 10k, 1/10W, 1%, TF, KOA
ROHS
CR0603-10W-1003FT
1
ea
R10
RES, SMD, 0603, 100k, 1/10W, 1%,
TF, ROHS
ERJ-6RQF3R3V
1
ea
R8
RES, SMD, 0805, 3.3Ω, 1/8W, 1%, TF, PANASONIC
ROHS
CR0805-8W-1001FT
3
ea
R26, R27, R28
RES, SMD, 0805, 1k, 1/8W, 1%, TF,
ROHS
0
ea
C23, C24
DO NOT POPULATE OR PURCHASE
VENKEL
VENKEL
Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is
cautioned to verify that the Application Note or Technical Brief is current before proceeding.
For information regarding Intersil Corporation and its products, see www.intersil.com
Submit Document Feedback
19
AN1932.3
February 1, 2016