BOB12W Series 20130813A

Isolated DC-DC Converters
BOB12W Series -- 12 Watt
Bothhand USA
Features
Wide 4 : 1 Input Voltage Range(9~36V,18~75V)
Remote On/Off
High Efficiency up to 87%
Input / Output Isolation Voltage: 1.5K VDC
Extended Operating Temperature Range: -40°C to +85°C
Output Short Circuit Protection:
Description
Hiccup, continuous & Auto Recovery
Over Voltage Protection: Clamp Mode
Shielded Metal Case with Insulated Baseplate
Lead Free Design, RoHS Compliant
24pin DIP Package with Industry-Standard Footprint
The BOB12W Series are isolated 12W DC/DC converters.
Designed with highly efficiency, allow the operating
temperature range of these units to be -40°C to +85°C in
a 24 pin DIP package with industry-standard footprint.
Further features include wide 4 : 1 input voltage range,
remote on/off control, short-circuit protection and over
voltage protection.
Customer Design Available
Applications
Safety Standard / Approval : IEC / EN 60950-1
These converters are well suitable for battery operated
equipment, measurement equipment, telecom, wireless
network, Industry control system, everywhere where
isolated, tightly regulated voltages and compact size are
required.
Technical Specification
All specifications are typical at nominal input, full load and 25°C unless otherwise stated.
Output
(2) Capacitive
Output Current (mA)
Input Current (mA)
Model
Input Voltage
Eff .
Voltage
Load, max.
Number
Range
(%)
(3)
Min. Load (1)
Full. Load
No Load
Full Load
(V)
(uF)
3.3
0
83
BOB12-24S0W
3500
49
609
35700
5.1
0
58
638
84
2400
BOB12-24S1W
9400
BOB12-24S2W
9~36V
BOB12-24S3W Nominal:24V
BOB12-24D1W
12
0
1000
14
617
85
3530
15
0
800
17
617
85
2200
±5
0
±1200
18
642
82
6900
BOB12-24D2W
±12
5
±500
17
617
85
1760
BOB12-24D3W
±15
0
±400
17
617
85
1100
BOB12-48S0W
3.3
0
3500
19
300
84
21000
BOB12-48S1W
5.1
0
2400
24
315
85
12860
BOB12-48S2W
12
80
1000
6
302
87
2300
15
30
800
6
302
87
1660
18~75V
BOB12-48S3W Nominal:48V
BOB12-48D1W
±5
80
±1200
6
317
83
6030
BOB12-48D2W
±12
0
±500
13
309
85
1100
BOB12-48D3W
±15
0
±400
9
304
86
760
[email protected]
www.bothhandusa.com
Rev:20130813A
Page 1 of 7
Isolated DC-DC Converters
BOB12W Series -- 12 Watt
Bothhand USA
Input Specifications
Input Voltage
24V nominal input
9-36V
48V nominal input
18-75V
Input filter
Pi Type
Input surge voltage
24V input
50V
(100ms max.)
48V input
100V
Input reflected ripple current
Nominal Vin and full load
Start up time
Nominal Vin and constant resistive load
Remote ON/OFF
100mAp-p typ.
75ms typ.
Open or 3.5V<Vr<12V
Converter: ON
Short
Converter: OFF
(4)
or 0V<Vr<0.5V
Sourcing current of remote control pin
Nominal Vin
<0.2 mA
Idle input current (at Remote OFF state)
Nominal Vin
<7.5 mA
Environmental Specifications
-40°C to +85°C (with derating)
Operating ambient temperature
+100°C
Maximum case temperature
-55°C to +105°C
Storage temperature range
5% to 95% RH
Relative humidity
±0.02% / °C max.
Temperature coefficient
Output Specifications
12 Watts max.
Output power
Voltage accuracy
Full load and nominal Vin
±1.2%
See table
Minimum load
Line regulation
LL to HL at full load
25% load to full load
Load Regulation
Balanced load
±0.5%
Single
±1%
Dual
±1%
Unbalanced load 25% to 100% full load
Ripple and Noise
±5%
20MHz bandwidth
85mVp-p max.
3.3Vout models
3.9V
Over voltage protection
5Vout models
6.2V
(Zener Diode Clamp)
12Vout models
15V
15Vout models
18V
See table
Capacitive load
Over load protection
% of full load at nominal input
Short circuit protection
Hiccup, continuous (Auto Recovery)
Transient response settling time
50% load step change
Transient response over shoot
di/dt=0.8A/µs
[email protected]
150% typ.
www.bothhandusa.com
350µs typ.
≤ ±5% of Vo
Rev:20130813A
Page 2 of 7
Isolated DC-DC Converters
BOB12W Series -- 12 Watt
Bothhand USA
General Specifications
Efficiency
Nominal input
Isolation voltage
Input to output
Isolation resistance
See table
1500VDC
9
500VDC
10 Ohms min.
Isolation capacitance
260pF typ.
Switching frequency
400kHz typ.
6
Reliability, calculated MTBF
2.11 × 10 Hrs
Physical Specifications
Case material
Nickel-coated copper
Base material
Non-conductive black plastic
Silicon rubber (UL94V-0)
Potting material
1.25 × 0.80 × 0.40 Inch
Dimensions
(31.75 × 20.32 × 10.16 mm)
Weight
18g (0.62oz) typ.
BOB12W Series
Power Derating Curve
(5)
Output Power (%)
120
100
80
60
40
20
0
68
-40
-20
0
20
40
60
80
100
120
Ambient Temp.TA (℃)
[email protected]
Efficiency (%)
BOB12-48S1W
Output Current vs. Efficiency
Efficiency (%)
BOB12-48S1W
Input voltage vs. Efficiency
www.bothhandusa.com
Rev:20130813A
Page 3 of 7
Isolated DC-DC Converters
BOB12W Series -- 12 Watt
Bothhand USA
Input voltage (V)
Output Current (A)
BOB12-48S1W
Transient Response at 50%~100% Max Load
BOB12-48S1W
Loop Gain & Phase at Vi=48V,Full Load
Note
1. Io below this value will not damage these converters, however, they may not meet all listed specifications.
2. Typical value, tested at nominal input and full load.
3. For each output.
4. Short to -Vin (Pin 2,3).
5. Based on BOB12-48S1W.
Mechanical Dimensions
Pin
1
2
3
9
11
14
16
22
23
Pin Assignment
Single
Dual
Remote On/Off
-Vin
-Vin
-Vin
-Vin
No function
Common
No function
-Vout
+Vout
+Vout
-Vout
Common
+Vin
+Vin
+Vin
+Vin
Unit: mm [inch]
Tolerance:±0.5[0.02]
[email protected]
www.bothhandusa.com
Rev:20130813A
Page 4 of 7
Isolated DC-DC Converters
BOB12W Series -- 12 Watt
Bothhand USA
Specifications subject to change without notice.
Test Configurations
All specifications are typical at nominal input, full load and 25°C unless otherwise stated.
A
A
DC
Power Supply
DC/DC
converter
V
V
Load
◎DC Power Supply: It offers a wide voltage and current range precisely.
◎Current meter (A): Accuracy 200μA ~ 200mA 4 ranges+(0.2% rdg + 2 digits)
2000mA ~ 20A
2 ranges+(0.3% rdg + 2 digits).
◎Voltage meter (V): Accuracy +(0.03% rdg + 4 digits).
◎Load: At full load.
◎Wires: The resistance of the wires must be small.
1. Input voltage range: Narrow input voltage range(±10%)、wide input voltage range (2:1 and 4:1)。
EX: Narrow input voltage range(±10%)
5V nominal input 4.5~5.5V
12V nominal input 10.8~13.2V
24V nominal input 21.6~26.4V
Wide input voltage range 2:1
5V nominal input 12V nominal input 24V nominal input 48V nominal input 4.5~9V
9~18V
18~36V
36~75V
Wide input voltage range 4:1 (W)
24V nominal input 9~36V
48V nominal input 18~75V
2. Input power :
Pin = Vin x Iin
Vin:Input voltage
Iin:Input current
Pout = Vout x Iout
Vout:Output voltage
Iout:Output current
3. Output power :
4. Efficiency :
Efficiency =
Pout
Pin
x100%
Pout: Output power
Pin: Input power
5. Voltage accuracy:
│
│Vout-Vout(nominal)│
Vout
[email protected]
x100%
www.bothhandusa.com
Rev:20130813A
Page 5 of 7
Bothhand USA
Isolated DC-DC Converters
BOB12W Series -- 12 Watt
Vout:Output voltage
Vout(nominal):Nominal output voltage
││││
││││
6. Line regulation: (1) Wide input voltage range and regulated output voltage series.
│
│Vout(LL)-Vout(HL)│
Vout(LL)
LL: Low Line input voltage
HL: High Line input voltage
x100%
(2) Narrow input voltage range(±10%)and unregulated output voltage series.
Line regulation=
Δ Vout
Δ Vin
ΔVout = Vout(+10%)-Vout(-10%) x100%
Vout
Vout(+10%):Output voltage at Vin = 1.1xVin(nominal)&full load
Vout(-10%):Output voltage at Vin = 0.9xVin(nominal)&full load
Vout:Output voltage at Vin = Vin(nominal)&full load
ΔVin = Vin(+10%)-Vin(-10%) x100%
Vin(nominal)
Vin(+10%):Input voltage = 1.1xVin(nominal)
Vin(-10%):Input voltage = 0.9xVin(nominal)
Vin(nominal):Nominal Input voltage
7. Load regulation :
│ x100%
│Vout(FL)-Vout(NL)│
Vout(FL)
Vout(FL): Output voltage at full load
Vout(NL): Output voltage at 25% full load or 10% full load
8. Ripple and Noise: as shown below. The bandwidth is 0-20MHz.
Ripple&Noise
Noise
Ripple
[email protected]
www.bothhandusa.com
Rev:20130813A
Page 6 of 7
Isolated DC-DC Converters
BOB12W Series -- 12 Watt
Bothhand USA
Output Ripple&Noise measurement test circuit: as shown below.
Copper strip
DC/DC
converter
Co
Load
Oscilloscope
Copper strip
Co: usually 0.47uF.
9. Temperature derating curve: The DC-DC converter will operate over a wider temperature range if less power is
drawn from the output and the device is already running. The temperature derating curve shows the operating
power-temperature range. As shown below.
Output Power (%)
120
100
80
60
40
20
0
68
-40
-20
0
20
40
60
80
100
120
Ambient Temp.TA (℃)
10. Switching frequency: The nominal operating frequency of the DC-DC converters.
11. Input to output isolation: The dielectric breakdown strength test between input and output circuits. This is the
isolation voltage the device is capable of withstanding for a specified time, usually 1 second or 1 minute.
[email protected]
www.bothhandusa.com
Rev:20130813A
Page 7 of 7