DATASHEET

1A Standard Buck PWM Regulator
ISL85001
Features
The ISL85001 is a high-performance, simple output controller
that provides a single, high frequency power solution for a
variety of point-of-load applications. The ISL85001 integrates a
1A standard buck PWM controller and switching MOSFET.
• Standard Buck Controller with Integrated Switching Power
MOSFET
The PWM controller in the ISL85001 drives an internal
switching N-Channel power MOSFET and requires an external
Schottky diode to generate an output voltage from 0.6V to
19V. The integrated power switch is optimized for excellent
thermal performance for up to 1A of output current. The
standard buck input voltage range supports a fixed 5V or
variable 5.5V to 25V range. The PWM regulator switches at a
fixed frequency of 500kHz and utilizes simple voltage mode
control with input voltage feed-forward to provide flexibility in
component selection and minimize solution size. Protection
features include overcurrent, undervoltage and thermal
overload protection integrated into the IC. The ISL85001
power-good signal output indicates loss of regulation on the
PWM output.
ISL85001 is available in a small 4mmx3mm Dual Flat No-Lead
(DFN) package.
Related Literature
• Integrated Boot Diode
• Input Voltage Range
- Fixed 5V ±10%
- Variable 5.5V to 25V
• PWM Output Voltage Adjustable from 0.6V to 19V with
Continuous Output Current up to 1A
• ±1% VFB Tolerance
• Voltage Mode Control with Voltage Feed-Forward
• Fixed 500kHz Switching Frequency
• Externally Adjustable Soft-Start Time
• Output Undervoltage Protection
• Enable Inputs
• PGOOD Output
• Overcurrent Protection
• Thermal Overload Protection
• Internal 5V LDO Regulator
• See AN1443, “ISL85001EVAL1Z 1A Regulator Standard
Buck PWM”
• See TB417, “Designing Stable Compensation Networks for
Single Phase Voltage Mode Buck Regulators”
• Pb-Free (RoHS compliant)
Applications
• General Purpose
• WLAN Cards-PCMCIA, Cardbus32, MiniPCI Cards-Compact
Flash Cards
• Hand-Held Instruments
• LCD Panel
• Set-top Box
May 29, 2012
FN6769.2
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2008, 2009, 2012. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
ISL85001
Typical Application Schematic
R3
301
C3
100pF
VOUT
C2
2.2nF
R4
3.16k
FB
SS
C1
10pF
COMP
R2
31k
C5
0.1µF
R1
10k
VIN
5.5V TO 25V
C9
10µF
EN
PG
ISL85001
L
22µH
PHASE
BOOT
VOUT = 2.5V
C10
0.1µF
C11
47µF
D
B340LB
GND
VDD
C13
1 µF
FIGURE 1. VIN RANGE FROM 5.5V TO 25V
2
FN6769.2
May 29, 2012
ISL85001
BOOT
FB
COMP
Functional Block Diagram
VDD
VDD
SOFT-START
CONTROL
VIN (x2)
30µA
OC
MONITOR
PWM
EA
+
-
VOLTAGE
MONITOR
+
-
SS
0.6V
REFERENCE
FAULT
MONITOR
EN
THERMAL
MONITOR
+150°C
RAMP
GENERATOR
VIN
GATE
DRIVE
PHASE (x2)
OSCILLATOR
OC
MONITOR
POR
VIN
LDO
POWER-ON
RESET
MONITOR
VDD
VDD
GND
PG
EPAD GND
3
FN6769.2
May 29, 2012
ISL85001
Pin Configuration
ISL85001
(12 LD 4X3 DFN)
TOP VIEW
FB
1
12
VIN
COMP
2
11
VIN
SS
3
10
PHASE
GND
EN
4
9
PHASE
PG
5
8
BOOT
GND
6
7
VDD
Pin Descriptions
SYMBOL
PIN
NUMBER
FB , COMP
1, 2
SS
3
Program pin for soft-start duration. A regulated 30µA pull-up current source charges a capacitor connected from the pin to
GND. The output voltage of the converter follows the ramping voltage on the SS pin.
EN
4
PWM controller enable input. The PWM converter output is held off when the pin is pulled to ground. When the voltage on this
pin rises above 1.7V, the chip is enabled.
PG
5
PWM converter power-good output. Open drain logic output that is pulled to ground when the output voltage is outside
regulation limits. Connect a 100kΩ resistor from this pin to VDD. Pin is low when the buck regulator output voltage is not within
10% of the respective nominal voltage, or during the soft-start interval. Pin is high impedance when the output is within
regulation.
GND
6
Ground connect for the IC and thermal relief for the package. The exposed pad must be connected to GND and soldered to the
PCB. All voltage levels are measured with respect to this pin.
VDD
7
Internal 5V linear regulator output provides bias to all the internal control logic. The ISL85001 may be powered directly from a 5V
(±10%) supply at this pin. When used as a 5V supply input, this pin must be externally connected to VIN. The VDD pin must always
be decoupled to GND with a ceramic bypass capacitor (minimum 1µF) located close to the pin.
DESCRIPTION
The standard buck regulator employs a single voltage control loop. FB is the negative input to the voltage loop error amplifier.
COMP is the output of the error amplifier. The output voltage is set by an external resistor divider connected to FB. With a
properly selected divider, the output voltage can be set to any voltage between the power rail (reduced by converter losses) and
the 0.6V reference. Connecting an AC network across COMP and FB provides loop compensation to the amplifier.
In addition, the PWM regulator power-good and undervoltage protection circuitry use FB to monitor the regulator output
voltage.
TABLE 1. INPUT SUPPLY CONFIGURATION
INPUT
PIN CONFIGURATION
5.5V to 25V
Connect the input supply to the VIN pin only. The VDD pin will
provide a 5V output from the internal linear regulator.
5V ±10%
BOOT
8
PHASE
9, 10
VIN
11, 12
Connect the input supply to the VIN and VDD pins.
Floating bootstrap supply pin for the power MOSFET gate driver. The bootstrap capacitor provides the necessary charge to turn
and hold on the internal N-Channel MOSFET. Connect an external capacitor from this pin to PHASE.
Switch node connections to internal power MOSFET source, external output inductor and external diode cathode.
The input supply for the PWM regulator power stage and the source for the internal linear regulator that provides bias for the
IC. Place a ceramic capacitor from VIN to GND, close to the IC for decoupling (typical 10µF).
4
FN6769.2
May 29, 2012
ISL85001
Ordering Information
PART NUMBER
(Notes 1, 2, 3)
PART
MARKING
ISL85001IRZ
501Z
TEMP. RANGE
(°C)
-40 to +85
PACKAGE
(Pb-Free)
12 Ld DFN
PKG.
DWG. #
L12.4x3
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL85001. For more information on MSL please see tech brief TB363.
5
FN6769.2
May 29, 2012
ISL85001
Absolute Maximum Ratings
Thermal Information
VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 26V
BOOT to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 33V
BOOT to PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.03V to 6V
VDD, FB, EN, COMP, PG, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V
Thermal Resistance
θJA (°C/W) θJC (°C/W)
QFN Package (Notes 4, 5) . . . . . . . . . . . . . .
39
3
Ambient Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions
VIN Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 25V
Load Current Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A to 1A
Ambient Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379 for details.
5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications
PARAMETER
Typical Specifications are Measured at the Following Conditions: TA = -40°C to +85°C.
SYMBOL
TEST CONDITIONS
MIN
MAX
(Note 8) TYP (Note 8) UNITS
SUPPLY VOLTAGE
VIN Voltage Range
VIN
VIN connected to VDD
5.5
-
25
V
4.5
5.0
5.5
V
VIN Operating Supply Current
IOP
(Note 6)
-
2
2.5
mA
VIN Shutdown Supply Current
ISD
VIN = 15V, EN = GND
-
80
100
µA
4.00
4.15
4.30
V
-
275
-
mV
4.5
5.00
5.5
V
VIN = 5.5V to 25V, IREF = 0
0.594
0.6
0.606
V
FB Line Regulation
IOUT = 0mA, VIN = 5.5V to 25V
-0.05
-
0.05
%
FB Leakage Current
VFB = 0.6V
-50
0
50
nA
450
500
550
kHz
0.65
0.75
0.95
V/V
-
1.3
-
V
0.75
0.8
0.85
V
80
-
-
%
-
88
-
dB
-
15
-
MHz
-
5
-
V/µs
POWER-ON RESET
VDD POR Threshold
Rising Edge
Hysteresis
INTERNAL VDD LDO
VDD Output Voltage Range
VIN = 5.5V to 25V, IVDD = 0mA to 30mA
REFERENCE
Reference Voltage
VFB
STANDARD BUCK PWM REGULATOR
OSCILLATOR AND PWM MODULATOR
Nominal Switching Frequency
fSW
Modulator Gain
AMOD
VIN = 12V (AMOD = 8/VIN)
Peak-to-Peak Sawtooth Amplitude
VRAMP
VIN = 12V (VP-P = VIN/8)
PWM Ramp Offset Voltage
VOFFSET
Maximum Duty Cycle
DCmax
COMP > 4V
ERROR AMPLIFIER
Open-Loop Gain
Gain Bandwidth Product
GBWP
Slew Rate
SR
6
COMP = 10pF
FN6769.2
May 29, 2012
ISL85001
Electrical Specifications
PARAMETER
Typical Specifications are Measured at the Following Conditions: TA = -40°C to +85°C. (Continued)
SYMBOL
TEST CONDITIONS
MIN
MAX
(Note 8) TYP (Note 8) UNITS
ENABLE SECTION
EN Threshold
Rising Edge
Hysteresis
EN Logic Input Current
1.2
1.7
2.2
V
-
400
-
mV
-1
-
1
µA
FAULT PROTECTION
Thermal Shutdown Temperature
PWM UV Trip Level
TSD
Rising Threshold
-
150
-
°C
THYS
Hysteresis
-
15
-
°C
VUV
Referred to Nominal VOUT
70
75
80
%
-
270
-
ns
1.37
1.7
2.17
A
-
100
-
ns
Lower Level, Falling Edge, with typically 15mV hysteresis
85
88
91
%
Upper Level, Rising Edge, with typically 15mV hysteresis
108
112
116
%
-
9
-
µs
PWM UVP Propagation Delay
VIN = VDD = 5V, (Note 7)
PWM OCP Threshold
OCP Blanking Time
POWER-GOOD
PG Trip Level Referred to Nominal VOUT
PG Propagation Delay
PG Low Voltage
ISINK = 4mA
-
0.05
0.3
V
PG Leakage Current
VPG = 5.5V, VFB = 0.6V, VDD = 5.5V
-1
-
1
µA
Soft-Start Threshold to Enable Buck
0.9
1
1.1
V
Soft-Start Threshold to Enable PG
2.5
3.0
3.5
V
-
3.45
-
V
20
30
40
µA
VSS = 3.0V
-
25
-
mA
IOUT = 100mA, Die Resistance
-
120
200
mΩ
SOFT-START SECTION
Soft-Start Voltage High
Soft-Start Charging Current
Soft-Start Pull-down
POWER MOSFET
rDS(ON)
NOTES:
6. Test Condition: VIN = 15V, FB forced above regulation point (0.6V), no switching, and power MOSFET gate charging current not included.
7. Excluding the blanking time.
8. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
7
FN6769.2
May 29, 2012
ISL85001
Typical Performance Curves
Unless otherwise noted, operating conditions are: TA = +25°C, VIN = 12V, EN = VDD, L = 22µH, C9 = 10µF,
C11 = 47µF, IOUT = 0A to 1A. See “VIN” on page 4.
1.0
1.0
0.9
0.9
0.8
0.7
0.6
3.3VOUT
1.8VOUT
EFFICIENCY (%)
EFFICIENCY (%)
0.8
1.5VOUT
2.5VOUT
0.5
0.4
0.3
0.7
0.4
0.3
0.2
0.1
0.4
0.6
OUTPUT LOAD (A)
0.8
0.0
0.0
1.0
0.2
0.4
0.6
OUTPUT LOAD (A)
0.8
1.0
FIGURE 3. EFFICIENCY vs LOAD, 500kHz, 12VIN
FIGURE 2. EFFICIENCY vs LOAD, 500kHz, 5VIN
1.0
0.8
POWER DISSIPATION (W)
0.9
0.8
EFFICIENCY (%)
1.2VOUT
1.5VOUT
1.8VOUT
2.5VOUT
0.5
0.1
0.2
5VOUT
0.6
0.2
0.0
0.0
0.7
0.6
5VOUT
0.5
1.2VOUT
1.5VOUT
1.8VOUT
2.5VOUT
0.4
0.3
0.2
0.1
0.0
0.0
0.2
0.4
0.6
OUTPUT LOAD (A)
0.8
12VIN
0.6
0.5
25VIN
0.4
0.3
0.2
5VIN
0.1
0.1
0.2
0.3
0.4
0.5
0.6
OUTPUT LOAD (A)
0.7
0.8
0.9
1.0
FIGURE 5. POWER DISSIPATION vs LOAD, 500kHz, 2.5VOUT
1.206
1.510
1.205
OUTPUT VOLTAGE (V)
1.203
1.202
1.201
5VIN
1.200
12VIN
1.509
12VIN
25VIN
1.204
1.199
1.198
0.0
0.7
0.0
0.0
1.0
FIGURE 4. EFFICIENCY vs LOAD, 500kHz, 25VIN
OUTPUT VOLTAGE (V)
3.3VOUT
25VIN
1.508
1.507
1.506
1.505
5VIN
1.504
1.503
0.2
0.4
0.6
OUTPUT LOAD (A)
0.8
FIGURE 6. VOUT REGULATION vs LOAD, 500kHz, 1.2VOUT
8
1.0
1.502
0.0
0.2
0.4
0.6
OUTPUT LOAD (A)
0.8
1.0
FIGURE 7. VOUT REGULATION vs LOAD, 500kHz, 1.5VOUT
FN6769.2
May 29, 2012
ISL85001
Typical Performance Curves
Unless otherwise noted, operating conditions are: TA = +25°C, VIN = 12V, EN = VDD, L = 22µH, C9 = 10µF,
C11 = 47µF, IOUT = 0A to 1A. See “VIN” on page 4. (Continued)
1.814
2.506
1.812
25VIN
2.505
12VIN
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1.813
1.811
1.810
1.809
1.808
5VIN
2.502
2.501
2.500
2.499
0.2
0.4
0.6
OUTPUT LOAD (A)
0.8
0.4
0.6
OUTPUT LOAD (A)
0.8
1.0
4.99
3.328
4.98
12VIN
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
0.2
FIGURE 9. VOUT REGULATION vs LOAD, 500kHz, 2.5VOUT
3.330
25VIN
3.324
3.322
3.320
7VIN
3.318
3.316
3.314
0.0
5VIN
2.498
0.0
1.0
FIGURE 8. VOUT REGULATION vs LOAD, 500kHz, 1.8VOUT
3.326
12VIN
2.503
1.807
1.806
0.0
25VIN
2.504
4.97
25VIN
4.96
4.95
7VIN
4.94
4.93
4.92
0.2
0.4
0.6
OUTPUT LOAD (A)
0.8
FIGURE 10. VOUT REGULATION vs LOAD, 500kHz, 3.3VOUT
1.0
4.91
12VIN
0.1
0.3
0.5
0.7
OUTPUT LOAD (A)
0.9
FIGURE 11. VOUT REGULATION vs LOAD, 500kHz, 5VOUT
PHASE 5V/DIV
PHASE 5V/DIV
VOUT RIPPLE
20mV/DIV
VOUT RIPPLE
20mV/DIV
IL 0.1A/DIV
IL 0.5A/DIV
FIGURE 12. STEADY STATE OPERATION AT NO LOAD (5µs/DIV)
9
FIGURE 13. STEADY STATE OPERATION AT FULL LOAD (1µs/DIV)
FN6769.2
May 29, 2012
ISL85001
Typical Performance Curves
Unless otherwise noted, operating conditions are: TA = +25°C, VIN = 12V, EN = VDD, L = 22µH, C9 = 10µF,
C11 = 47µF, IOUT = 0A to 1A. See “VIN” on page 4. (Continued)
PHASE 10V/DIV
EN 5V/DIV
VOUT
2V/DIV
VOUT RIPPLE
100mV/DIV
IL 0.5A/DIV
PG 5V/DIV
IL 0.5A/DIV
SS 5V/DIV
FIGURE 15. SOFT-START AT NO LOAD (2ms/DIV)
FIGURE 14. LOAD TRANSIENT (200µs/DIV)
EN 5V/DIV
EN 5V/DIV
VOUT
2V/DIV
VOUT
2V/DIV
IL 0.5A/DIV
IL 1A/DIV
PG 5V/DIV
SS 5V/DIV
PG 5V/DIV
FIGURE 17. SHUT DOWN CIRCUIT (100µs/DIV)
FIGURE 16. SOFT-START AT FULL LOAD (2ms/DIV)
PHASE 10V/DIV
PHASE 10V/DIV
VOUT
1V/DIV
IL 1A/DIV
VOUT
1V/DIV
IL 1A/DIV
PG 5V/DIV
PG 5V/DIV
FIGURE 18. OUTPUT SHORT CIRCUIT (5µs/DIV)
10
FIGURE 19. OUTPUT SHORT CIRCUIT RECOVERY (1ms/DIV)
FN6769.2
May 29, 2012
ISL85001
Detailed Description
The ISL85001 combines a standard buck PWM controller with
an integrated switching MOSFET. The buck controller drives an
internal N-Channel MOSFET and requires an external diode to
deliver load current up to 1A. A Schottky diode is
recommended for improved efficiency and performance over a
standard diode. The standard buck regulator can operate from
either an unregulated DC source, such as a battery, with a
voltage ranging from +5.5V to +25V, or from a regulated
system rail of +5V. When operating from +5.5V or greater, the
controller is biased from an internal +5V LDO voltage
regulator. The converter output is regulated down to 0.6V from
either input source. These features make the ISL85001 ideally
suited for FPGA and wireless chipset power applications.
The PWM control loop uses a single output voltage loop with input
voltage feed forward, which simplifies feedback loop
compensation and rejects input voltage variation. External
feedback loop compensation allows flexibility in output filter
component selection. The regulator switches at a fixed 500kHz.
The buck regulator is equipped with a lossless current limit
scheme. The current limit in the buck regulator is achieved by
monitoring the drain-to-source voltage drop of the internal
switching power MOSFET. The current limit threshold is
internally set at 1.7A. The part also features undervoltage
protection by latching the switching MOSFET driver to the
OFF-state during an overcurrent, when the output voltage is
lower than 70% of the regulated output. This helps minimize
power dissipation during a short-circuit condition. Due to only
the switching power MOSFET integration, there is no
overvoltage protection feature for this part.
+5V Internal Bias Supply (VDD)
Voltage applied to the VIN pin with respect to GND is regulated
to +5V DC by an internal LDO regulator. The output of the LDO,
VDD, is the bias voltage used by all the internal control and
protection circuitry. The VDD pin requires a ceramic capacitor
connected to GND. The capacitor serves to stabilize the LDO and
to decouple load transients.
The input voltage range for the ISL85001 is specified as +5.5V
to +25V or +5V ±10%. In the case of an unregulated supply
case, the power supply is connected to VIN only. Once enabled,
the linear regulator will turn-on and rise to +5V on VDD. In the
+5V supply case, the VDD and VIN pins must be tied together
to bypass the LDO. The external decoupling capacitor is still
required in this mode.
Operation Initialization
The power-on reset circuitry and enable inputs prevent false
start-up of the PWM regulator output. Once all the input
criteria are met, the controller soft-starts the output voltage to
the programmed level.
Power-On Reset and Undervoltage Lockout
The PWM portion of the ISL85001 automatically initializes
upon receipt of input power. The power-on reset (POR) function
continually monitors the VDD voltage. While below the POR
thresholds, the controller inhibits switching off the internal
11
power MOSFET. Once exceeded, the controller initializes the
internal soft-start circuitry. If either input supply drops below
their falling POR threshold during soft-start or operation, the
buck regulator latches off.
Enable and Disable
All internal power devices are held in a high-impedance state,
which ensures they remain off while in shutdown mode.
Typically, the enable input for a specific output is toggled high
after the input supply to that regulator is active and the
internal LDO has exceeded it’s POR threshold.
The EN pin enables the buck controller portion of the
ISL85001. When the voltage on the EN pin exceeds the POR
rising threshold, the controller initiates the soft-start function
for the PWM regulator. If the voltage on the EN pin drops below
the POR falling threshold, the buck regulator shuts down.
Pulling the EN pin low simultaneously put the output into
shutdown mode and supply current drops to 100µA typical.
Soft-Start
Once the input supply latch and enable threshold are met, the
soft-start function is initialized. The soft-start circuitry begins
sourcing 30µA, from an internal current source, which charges
the external soft-start capacitor. The voltage on SS begins
ramping linearly from ground until the voltage across the
soft-start capacitor reaches 3.0V. This linear ramp is applied to
the non-inverting input of the internal error amplifier and
overrides the nominal 0.6V reference. The output voltage
reaches its regulation value when the soft-start capacitor
voltage reaches 1.6V. Connect a capacitor from SS pin to
ground. This capacitor (along with an internal 30µA current
source) sets the soft-start interval of the converter, tSS.
C SS [ μF ] = 50 ⋅ t SS [ s ]
(EQ. 1)
Upon disable, the SS pin voltage will discharge to zero voltage.
Power-Good
PG is an open-drain output of a window comparator that
continuously monitors the buck regulator output voltage. PG is
actively held low when EN is low and during the buck regulator
soft-start period. After the soft-start period terminates, PG
becomes high impedance as long as the output voltage is within
±12% of the nominal regulation voltage set by FB. When VOUT
drops 12% below or rises 12% above the nominal regulation
voltage, the ISL85001 pulls PG low. Any fault condition forces PG
low until the fault condition is cleared by attempts to soft-start.
For logic level output voltages, connect an external pull-up resistor
between PG and VDD. A 100kΩ resistor works well in most
applications.
Output Voltage Selection
The regulator output voltages can be programmed using
external resistor dividers that scale the voltage feedback
relative to the internal reference voltage. The scaled voltage is
fed back to the inverting input of the error amplifier; refer to
Figure 20.
The output voltage programming resistor, R4, will depend on the
value chosen for the feedback resistor, R1, and the desired output
FN6769.2
May 29, 2012
ISL85001
voltage, VOUT, of the regulator; see Equation 2. The value for the
feedback resistor is typically between 1kΩ and 10kΩ.
R 1 × 0.6V
R 4 = ---------------------------------V OUT – 0.6V
(EQ. 2)
Undervoltage Protection
If the output voltage desired is 0.6V, then RP is left
unpopulated.
VOUT
R1
+
EA
There is 100ns blanking time for noise immunity. It is
recommended to operate the duty cycle higher than the
blanking time to insure proper overcurrent protection.
R4
0.6V
REFERENCE
FIGURE 20. EXTERNAL RESISTOR DIVIDER
The buck output can be programmed as high as 19V. Proper
heatsinking must be provided to insure that the junction
temperature does not exceed +125°C.
When the output is set greater than 2.7V, it is recommended to
pre-load at least 10mA and make sure that the input rise time is
much faster than the VOUT1 rise time. This allows the BOOT
capacitor adequate time to charge for proper operation.
Protection Features
If the voltage detected on the buck regulator FB pin falls 25%
below the internal reference voltage, the undervoltage fault
condition flag is set. The regulator is shutdown. The controller
enters a recovery mode similar to the overcurrent hiccup
mode. No action is taken for 4 soft-start cycles and the internal
undervoltage counter and fault condition flag are reset. A
normal soft-start cycle is attempted and normal operation
continues if the fault condition has cleared. If the undervoltage
counter overflows during soft-start, the converter is shut down
and this hiccup mode operation repeats.
Thermal Overload Protection
Thermal overload protection limits total power dissipation in
the ISL85001. There is a sensor on the chip to monitor the
junction temperature of the internal LDO and PWM switching
power N-Channel MOSFET. When the junction temperature (TJ)
of the sensor exceeds +150°C, the thermal sensor sends a
signal to the fault monitor.
The fault monitor commands the buck regulator to shut down.
The buck regulator soft-starts turn on again after the IC’s junction
temperature cools by +20°C. The buck regulator experiences
hiccup mode operation during continuous thermal overload
conditions. For continuous operation, do not exceed the +125°C
junction temperature rating.
The ISL85001 limits current in the power devices to limit on-chip
power dissipation. Overcurrent limits on the regulator protect the
internal power device from excessive thermal damage.
Undervoltage protection circuitry on the buck regulator provides a
second layer of protection for the internal power device under high
current condition.
Application Guidelines
Buck Regulator Overcurrent Protection
The ISL85001 operates at a fixed switching frequency of
500kHz.
During the PWM on-time, the current through the internal
switching MOSFET is sampled and scaled through an internal
pilot device. The sampled current is compared to a nominal
1.7A overcurrent limit. If the sampled current exceeds the
overcurrent limit reference level, an internal overcurrent fault
counter is set to 1 and an internal flag is set. The internal
power MOSFET is immediately turned off and will not be
turned on again until the next switching cycle.
The protection circuitry continues to monitor the current and
turns off the internal MOSFET as described. If the overcurrent
condition persists for eight sequential clock cycles, the
overcurrent fault counter overflows, indicating an overcurrent
fault condition exists. The regulator is shut down and
power-good goes low. If the overcurrent condition clears prior
to the counter reaching four consecutive cycles, the internal
flag and counter are reset.
The protection circuitry attempts to recover from the
overcurrent condition after waiting 4 soft-start cycles. The
internal overcurrent flag and counter are reset. A normal softstart cycle is attempted and normal operation continues if the
fault condition has cleared. If the overcurrent fault counter
overflows during soft-start, the converter shuts down and this
hiccup mode operation repeats.
12
Operating Frequency
Buck Regulator Output Capacitor Selection
An output capacitor is required to filter the inductor current
and supply the load transient current. The filtering
requirements are a function of the switching frequency and
the ripple current. The load transient requirements are a
function of the slew rate (di/dt) and the magnitude of the
transient load current. These requirements are generally met
with a mix of capacitors and careful layout.
Embedded processor systems are capable of producing
transient load rates above 1A/ns. High frequency capacitors
initially supply the transient and slow the current load rate seen
by the bulk capacitors. The bulk filter capacitor values are
generally determined by the ESR (Effective Series Resistance)
and voltage rating requirements rather than actual capacitance
requirements.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load on
specific decoupling requirements.
FN6769.2
May 29, 2012
ISL85001
Use only specialized low-ESR capacitors intended for switchingregulator applications for the bulk capacitors. The bulk capacitor’s
ESR will determine the output ripple voltage and the initial voltage
drop after a high slew-rate transient. An aluminum electrolytic
capacitor’s ESR value is related to the case size with lower ESR
available in larger case sizes. However, the Equivalent Series
Inductance (ESL) of these capacitors increases with case size and
can reduce the usefulness of the capacitor to high slew-rate
transient loading. Unfortunately, ESL is not a specified parameter.
Work with your capacitor supplier and measure the capacitor’s
impedance with frequency to select a suitable component. In most
cases, multiple electrolytic capacitors of small case size perform
better than a single large case capacitor.
Output Inductor Selection
The output inductor is selected to meet the output voltage ripple
requirements and minimize the converter’s response time to the
load transient. The inductor value determines the converter’s
ripple current and the ripple voltage is a function of the ripple
current. The ripple voltage and current are approximated by
Equation 3:
ΔI =
VIN - VOUT
Fs x L
x
VOUT
VIN
ΔVOUT = ΔI x ESR
(EQ. 3)
with a 20% derating factor. The power dissipation is shown in
Equation 5:
V OUT⎞
⎛
P D [ W ] = I OUT ⋅ V D ⋅ ⎜ 1 – ----------------⎟
V IN ⎠
⎝
(EQ. 5)
where VD is the voltage of the Schottky diode = 0.5V to 0.7V
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use small ceramic capacitors for
high frequency decoupling and bulk capacitors to supply the
current needed each time the switching MOSFET turns on. Place
the small ceramic capacitors physically close to the MOSFET VIN
pins (switching MOSFET drain) and the Schottky diode anode.
The important parameters for the bulk input capacitance are the
voltage rating and the RMS current rating. For reliable operation,
select bulk capacitors with voltage and current ratings above the
maximum input voltage and largest RMS current required by the
circuit. Their voltage rating should be at least 1.25x greater than
the maximum input voltage, while a voltage rating of 1.5x is a
conservative guideline. For most cases, the RMS current rating
requirement for the input capacitor of a buck regulator is
approximately 1/2 the DC load current.
Increasing the value of inductance reduces the ripple current and
voltage. However, the large inductance values reduce the
converter’s response time to a load transient.
The maximum RMS current required by the regulator may be
closely approximated through Equation 6:
One of the parameters limiting the converter’s response to a
load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL85001 will provide either 0% or 80% duty cycle in response
to a load transient. The response time is the time required to
slew the inductor current from an initial current value to the
transient current level. During this interval, the difference
between the inductor current and the transient current level
must be supplied by the output capacitor. Minimizing the
response time can minimize the output capacitance required.
I RMS
The response time to a transient is different for the application of
load and the removal of load. Equation 4 gives the approximate
response time interval for application and removal of a transient
load:
tRISE =
L x ITRAN
VIN - VOUT
tFALL =
L x ITRAN
VOUT
(EQ. 4)
where: ITRAN is the transient load current step, tRISE is the
response time to the application of load, and tFALL is the
response time to the removal of load. The worst case response
time can be either at the application or removal of load. Be sure
to check Equation 4 at the minimum and maximum output levels
for the worst case response time.
Rectifier Selection
MAX
=
V OUT ⎛
V IN – V OUT V OUT 2
2
1
-------------- × I OUT
+ ------ × ⎛ ----------------------------- × --------------⎞ ⎞
⎝
V IN
V IN ⎠ ⎠
12 ⎝ L × f s
MAX
(EQ. 6)
For a through-hole design, several electrolytic capacitors may be
needed. For surface mount designs, solid tantalum capacitors
can be used, but caution must be exercised with regard to the
capacitor surge current rating. These capacitors must be capable
of handling the surge-current at power-up. Some capacitor series
available from reputable manufacturers are surge current tested.
Feedback Compensation
Figure 21 highlights the voltage-mode control loop for a
synchronous-rectified buck converter. The output voltage (VOUT)
is regulated to the Reference voltage level. The error amplifier
output (VE/A) is compared with the oscillator (OSC) triangular
wave to provide a pulse-width modulated (PWM) wave with an
amplitude of VIN at the PHASE node. The PWM wave is smoothed
by the output filter (LO and CO).
The modulator transfer function is the small-signal transfer
function of VOUT/VE/A . This function is dominated by a DC Gain
and the output filter (LO and CO), with a double pole break
frequency at FLC and a zero at FESR . The DC Gain of the
modulator is simply the input voltage (VIN) divided by the
peak-to-peak oscillator voltage ΔVOSC .
Current circulates from ground to the junction of the MOSFET and
the inductor when the high-side switch is off. As a consequence,
the polarity of the switching node is negative with respect to
ground. This voltage is approximately -0.5V (a Schottky diode drop)
during the off-time. The rectifier's rated reverse breakdown voltage
must be at least equal to the maximum input voltage, preferably
13
FN6769.2
May 29, 2012
ISL85001
PWM
COMPARATOR
LO
+
DVOSC
Compensation Break Frequency Equations
VIN
DRIVER
OSC
VDDQ
PHASE
1
F P1 = --------------------------------------------------------⎛ C 1 x C 2⎞
2π x R 2 x ⎜ ----------------------⎟
⎝ C 1 + C 2 ⎠ (EQ. 8)
1
F Z2 = ------------------------------------------------------2π x ( R 1 + R 3 ) x C 3
1
F P2 = -----------------------------------2π x R 3 x C 3
CO
D
ESR
(PARASITIC)
ZFB
1
F Z1 = -----------------------------------2π x R 2 x C 2
VE/A
ZIN
+
ERROR
AMP
Figure 22 shows an asymptotic plot of the DC/DC converter’s
gain vs frequency. The actual Modulator Gain has a high gain
peak due to the high Q factor of the output filter and is not shown
in Figure 22. Using the previously mentioned guidelines should
give a Compensation Gain similar to the curve plotted. The open
loop error amplifier gain bounds the compensation gain. Check
the compensation gain at FP2 with the capabilities of the error
amplifier. The Closed Loop Gain is constructed on the graph of
Figure 4 by adding the Modulator Gain (in dB) to the
Compensation Gain (in dB). This is equivalent to multiplying the
modulator transfer function to the compensation transfer
function and plotting the gain.
REFERENCE
DETAILED COMPENSATION COMPONENTS
ZFB
C1
C2
VOUT
ZIN
C3
R2
R3
R1
COMP
FB
+
R4
ISL85001
REFERENCE
100
FIGURE 21. VOLTAGE-MODE BUCK CONVERTER COMPENSATION
DESIGN AND OUTPUT VOLTAGE SELECTION
1
F LC = ------------------------------------------2π x L O x C O
1
F ESR = -------------------------------------------2π x ESR x C O
(EQ. 7)
The compensation network consists of the error amplifier
(internal to the ISL85001) and the impedance networks ZIN and
ZFB. The goal of the compensation network is to provide a closed
loop transfer function with the highest 0dB crossing frequency
(f0dB) and adequate phase margin. Phase margin is the
difference between the closed loop phase at f0dB and 180°.
Equation 8 relates the compensation network’s poles, zeros and
gain to the components (R1 , R2 , R3 , C1 , C2 , and C3) in
Figure 22. Use the following guidelines for locating the poles and
zeros of the compensation network:
1. Pick Gain (R2/R1) for desired converter bandwidth.
FP1
FP2
OPEN LOOP
ERROR AMP GAIN
60
GAIN (dB)
Modulator Break Frequency Equations
FZ1 FZ2
80
40
20
20LOG
(R2/R1)
20LOG
(VIN/ΔVOSC)
0
COMPENSATION
GAIN
MODULATOR
GAIN
-20
CLOSED LOOP
GAIN
-40
FLC
-60
10
100
1k
FESR
10k
100k
1M
10M
FREQUENCY (Hz)
FIGURE 22. ASYMPTOTIC BODE PLOT OF CONVERTER GAIN
The compensation gain uses external impedance networks ZFB
and ZIN to provide a stable, high bandwidth (BW) overall loop. A
stable control loop has a gain crossing with -20dB/decade slope
and a phase margin greater than 45°. Include worst case
component variations when determining phase margin.
4. Place 1ST Pole at the ESR Zero.
A more detailed explanation of voltage mode control of a buck
regulator can be found in TB417, entitled “Designing Stable
Compensation Networks for Single Phase Voltage Mode Buck
Regulators.”
5. Place 2ND Pole at Half the Switching Frequency.
Layout Considerations
6. Check Gain against Error Amplifier’s Open-Loop Gain.
Layout is very important in high frequency switching converter
design. With power devices switching efficiently between 100kHz
and 600kHz, the resulting current transitions from one device to
another cause voltage spikes across the interconnecting
impedances and parasitic circuit elements. These voltage spikes
can degrade efficiency, radiate noise into the circuit, and lead to
device overvoltage stress. Careful component layout and printed
circuit board design minimizes these voltage spikes.
2. Place 1ST Zero Below Filter’s Double Pole (~75% FLC).
3. Place 2ND Zero at Filter’s Double Pole.
7. Estimate Phase Margin - Repeat if Necessary.
14
FN6769.2
May 29, 2012
ISL85001
As an example, consider the turn-off transition of the upper MOSFET.
Prior to turn-off, the MOSFET is carrying the full load current. During
turn-off, current stops flowing in the MOSFET and is picked up by the
Schottky diode. Any parasitic inductance in the switched current
path generates a large voltage spike during the switching interval.
Careful component selection, tight layout of the critical components,
and short, wide traces minimizes the magnitude of voltage spikes.
A multi-layer printed circuit board is recommended. Figure 23
shows the connections of the critical components in the converter.
Note that capacitors CIN and COUT could each represent numerous
physical capacitors. Dedicate one solid layer, usually a middle layer
of the PC board, for a ground plane and make all critical
component ground connections with vias to this layer. Dedicate
another solid layer as a power plane and break this plane into
smaller islands of common voltage levels. Keep the metal runs
from the PHASE terminals to the output inductor short. The power
plane should support the input power and output power nodes.
Use copper filled polygons on the top and bottom circuit layers for
the phase nodes. Use the remaining printed circuit layers for small
signal wiring.
In order to dissipate heat generated by the internal LDO and
MOSFET, the ground pad, pin 13, should be connected to the
internal ground plane through at least four vias. This allows the
heat to move away from the IC and also ties the pad to the
ground plane through a low impedance path.
CIN
ISL85001
L
VDD
5V
D
CBP1
VOUT1
PHASE
LOAD
There are two sets of critical components in the ISL85001
switching converter. The switching components are the most
critical because they switch large amounts of energy, and
therefore tend to generate large amounts of noise. Next are the
small signal components, which connect to sensitive nodes or
supply critical bypass current and signal coupling.
VIN
VIN
COUT1
GND
COMP
C2
C1
R2
R1
FB
R4
C3
R3
GND PAD
KEY
ISLAND ON POWER PLANE LAYER
ISLAND ON CIRCUIT AND/OR POWER PLANE LAYER
VIA CONNECTION TO GROUND PLANE
FIGURE 23. PRINTED CIRCUIT BOARD POWER PLANES AND
ISLANDS
The switching components should be placed close to the
ISL85001 first. Minimize the length of the connections between
the input capacitors, CIN, and the power switches by placing
them nearby. Position both the ceramic and bulk input capacitors
as close to the upper MOSFET drain as possible. Position the
output inductor and output capacitors between the upper and
Schottky diode and the load.
The critical small signal components include any bypass
capacitors, feedback components, and compensation
components. Place the PWM converter compensation
components close to the FB and COMP pins. The feedback
resistors should be located as close as possible to the FB pin with
vias tied straight to the ground plane as required.
15
FN6769.2
May 29, 2012
ISL85001
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you
have the latest revision.
DATE
REVISION
CHANGE
May 16, 2012
FN6769.2
Converted to new datasheet template.
Added “Related Literature” to page 1.
Added MSL note to “Ordering Information” on page 5.
Updated Tape & Reel note in “Ordering Information” on page 5 to new standard "Add “-T*” suffix for tape and
reel." The "*" covers all possible tape and reel options.
Removed incorrect note 4 reference from “Absolute Maximum Ratings” on page 6.
Added “Revision History” and “Products” on page 16.
Updated “Package Outline Drawing” on page 17. Added land pattern. Removed table and added dimensions to
drawing.
March 17, 2009
FN6769.1
Changed "Note 5" to "Note 6" in “VIN Operating Supply Current” on page 6
November 17, 2008
FN6769.0
Initial Release
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products
address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks.
Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a
complete list of Intersil product families.
For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on
intersil.com: ISL85001
To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff
FITs are available from our website at: http://rel.intersil.com/reports/search.php
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
16
FN6769.2
May 29, 2012
ISL85001
Package Outline Drawing
L12.4x3
12 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE
Rev 2, 7/10
3.30 +0.10/-0.15
4.00
2X 2.50
A
6
PIN 1
INDEX AREA
10X 0.50
PIN #1 INDEX AREA
B
6
1
12 X 0.40 ±0.10
6
1.70 +0.10/-0.15
3.00
(4X)
0.15
12
7
TOP VIEW
0.10M C A B
4 12 x 0.23 +0.07/-0.05
BOTTOM VIEW
SEE DETAIL "X"
( 3.30)
6
0.10 C
1
C
1.00 MAX
SEATING PLANE
0.08 C
SIDE VIEW
2.80
( 1.70 )
C
0.2 REF
5
12 X 0.60
7
0 . 00 MIN.
0 . 05 MAX.
12
( 12X 0.23 )
( 10X 0 . 5 )
DETAIL "X"
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Dimension applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Tiebar shown (if present) is a non-functional feature.
17
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
7.
Compliant to JEDEC MO-229 V4030D-4 issue E.
FN6769.2
May 29, 2012