EL5175, EL5375 ® Data Sheet May 10, 2007 550MHz Differential Line Receivers Features The EL5175 and EL5375 are single and triple high bandwidth amplifiers designed to extract the difference signal from noisy environments. They are primarily targeted for applications such as receiving signals from twisted-pair lines or any application where common mode noise injection is likely to occur. • Differential input range ±2.3V FN7306.6 • 550MHz 3dB bandwidth • 900V/µs slew rate • 60mA maximum output current • Single 5V or dual ±5V supplies The EL5175 and EL5375 are stable for a gain of one and requires two external resistors to set the voltage gain for each channel. • Low power, 9.6mA per channel • Pb-free plus anneal available (RoHS compliant) The output common mode level is set by the reference pin (VREF), which has a -3dB bandwidth of over 450MHz. Generally, this pin is grounded but it can be tied to any voltage reference. Applications The output can deliver a maximum of ±60mA and is short circuit protected to withstand a temporary overload condition. • VGA over twisted-pair The EL5175 is available in the 8 Ld SOIC and 8 Ld MSOP packages and the EL5375 in the 24 Ld QSOP package. All are specified for operation over the full -40°C to +85°C temperature range. • Twisted-pair receivers • Differential line receivers • ADSL/HDSL receivers • Differential to single-ended amplification • Reception of analog signals in a noisy environment Pinouts EL5175 (8 LD SOIC, MSOP) TOP VIEW FB 1 IN+ 2 EL5375 (24 LD QSOP) TOP VIEW 8 OUT REF1 1 7 VS- INP1 2 6 VS+ INN1 3 + IN- 3 REF 4 5 EN 24 NC + - 22 OUT1 21 NC NC 4 20 VSP REF2 5 INP2 6 + - 17 FB2 NC 8 16 OUT2 REF3 9 INN3 11 NC 12 1 19 VSN 18 NC INN2 7 INP3 10 23 FB1 + - 15 EN 14 FB3 13 OUT3 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-352-6832 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2004, 2005, 2007. All Rights Reserved All other trademarks mentioned are the property of their respective owners. EL5175, EL5375 Ordering Information PART NUMBER PART MARKING TAPE & REEL PACKAGE PKG. DWG. # EL5175IS 5175IS - 8 Ld SOIC (150 mil) MDP0027 EL5175IS-T7 5175IS 7” 8 Ld SOIC (150 mil) MDP0027 EL5175IS-T13 5175IS 13” 8 Ld SOIC (150 mil) MDP0027 EL5175ISZ (Note) 5175ISZ - 8 Ld SOIC (Pb-free) (150 mil) MDP0027 EL5175ISZ-T7 (Note) 5175ISZ 7” 8 Ld SOIC (Pb-free) (150 mil) MDP0027 EL5175ISZ-T13 (Note) 5175ISZ 13” 8 Ld SOIC (Pb-free) (150 mil) MDP0027 EL5175IY 5 - 8 Ld MSOP (3.0mm) MDP0043 EL5175IY-T7 5 7” 8 Ld MSOP (3.0mm) MDP0043 EL5175IY-T13 5 13” 8 Ld MSOP (3.0mm) MDP0043 EL5175IYZ (Note) BAAAB - 8 Ld MSOP (Pb-free) (3.0mm) MDP0043 EL5175IYZ-T7 (Note) BAAAB 7” 8 Ld MSOP (Pb-free) (3.0mm) MDP0043 EL5175IYZ-T13 (Note) BAAAB 13” 8 Ld MSOP (Pb-free) (3.0mm) MDP0043 EL5375IU EL5375IU - 24 Ld QSOP (150 mil) MDP0040 EL5375IU-T7 EL5375IU 7” 24 Ld QSOP (150 mil) MDP0040 EL5375IU-T13 EL5375IU 13” 24 Ld QSOP (150 mil) MDP0040 EL5375IUZ (Note) EL5375IUZ - 24 Ld QSOP (Pb-free) (150 mil) MDP0040 EL5375IUZ-T7 (Note) EL5375IUZ 7” 24 Ld QSOP (Pb-free) (150 mil) MDP0040 EL5375IUZ-T13 (Note) EL5375IUZ 13” 24 Ld QSOP (Pb-free) (150 mil) MDP0040 NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN7306.6 EL5175, EL5375 Absolute Maximum Ratings (TA = +25°C) Thermal Information Supply Voltage (VS+ to VS-) . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V Maximum Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . ±60mA Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +135°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER VS+ = +5V, VS- = -5V, TA = +25°C, VIN = 0V, RL = 500Ω, RF = 0, RG = OPEN, CL = 2.7pF, Unless Otherwise Specified. DESCRIPTION CONDITIONS MIN TYP MAX UNIT AC PERFORMANCE BW -3dB Bandwidth AV =1, CL = 2.7pF 550 MHz AV =2, RF = 806, CL = 2.7pF 190 MHz AV =10, RF = 806, CL = 2.7pF 20 MHz BW ± 0.1dB Bandwidth AV =1, CL = 2.7pF 60 MHz SR Slew Rate VOUT = 3VP-P, 20% to 80%, RL = 100Ω 600 V/µs VOUT = 3VP-P, 20% to 80%, RL = 500Ω 900 V/µs VOUT = 2VP-P 10 ns tSTL Settling Time to 0.1% tOVR Output Overdrive Recovery time 20 ns GBWP Gain Bandwidth Product 200 MHz VREFBW (-3dB) VREF -3dB Bandwidth AV =1, CL = 2.7pF 450 MHz VREFSR VREF Slew Rate VOUT = 2VP-P, 20% to 80% 1000 V/µs VN Input Voltage Noise at f = 10kHz 21 nV/√Hz IN Input Current Noise at f = 10kHz 2.7 pA/√Hz HD2 Second Harmonic Distortion VOUT = 1VP-P, 5MHz -70 dBc HD2 Second Harmonic Distortion VOUT = 1VP-P, 5MHz -66 dBc HD3 Third Harmonic Distortion VOUT = 1VP-P, 5MHz -94 dBc HD3 Third Harmonic Distortion VOUT = 1VP-P, 5MHz -84 dBc dG Differential Gain at 3.58MHz RL = 150Ω , AV =2 0.1 % dθ Differential Phase at 3.58MHz RL = 150Ω , AV =2 0.1 ° eS Channel Separation (EL5375) at f = 100kHz 90 dB EL5175 -3 ±40 mV EL5375 -3 ±30 mV -12.5 -6 µA INPUT CHARACTERISTICS VOS Input Referred Offset Voltage IIN Input Bias Current (VIN, VINB, VREF) RIN Differential Input Resistance CIN Differential Input Capacitance DMIR Differential Mode Input Range ±2.1 CMIR Common Mode Input Range at VIN+, VIN- VREFIN Reference Input Voltage Range 3 -25 VIN+ = VIN- = 0V 150 kΩ 1 pF ±2.3 ±2.5 V -4.3 +3.3 V -3.6 3.3 V FN7306.6 EL5175, EL5375 Electrical Specifications PARAMETER VS+ = +5V, VS- = -5V, TA = +25°C, VIN = 0V, RL = 500Ω, RF = 0, RG = OPEN, CL = 2.7pF, Unless Otherwise Specified. (Continued) DESCRIPTION CONDITIONS MIN TYP 75 95 MAX UNIT CMRR Input Common Mode Rejection Ratio VIN = ±2.5V dB Gain Gain Accuracy EL5175, VIN = 1V 0.979 0.994 1.009 V EL5375, VIN = 1V 0.977 0.992 1.007 V Positive Output Voltage Swing RL = 500Ω to GND 3.3 3.54 Negative Output Voltage Swing RL = 500Ω to GND IOUT(Max) Maximum Output Current RL = 10Ω ROUT Output Impedance OUTPUT CHARACTERISTICS VOUT -3.95 ±40 V -3.6 V ±67 mA 130 mΩ SUPPLY VSUPPLY Supply Operating Range IS (on) Power Supply Current Per Channel Enabled IS (off)+ 11 V 9.6 11 mA Positive Power Supply Current - Disabled EN pin tied to 4.8V, EL5175 80 100 µA EN pin tied to 4.8V, EL5375 1.7 5 µA -150 -120 -90 µA 45 56 dB IS (off)- Negative Power Supply Current Disabled PSRR Power Supply Rejection Ratio VS+ to VS- 4.75 8 VS from ±4.5V to ±5.5V ENABLE tEN Enable Time 80 ns tDS Disable Time 1.2 µs VIH EN Pin Voltage for Power-up VIL EN Pin Voltage for Shut-down IIH-EN EN Pin Input Current High Per Channel At VEN = 5V IIL-EN EN Pin Input Current Low Per Channel At VEN = 0V 4 VS+ - 1.5 VS+ - 0.5 V 40 -10 V -3 60 µA µA FN7306.6 EL5175, EL5375 Pin Descriptions EL5175 EL5375 PIN NAME PIN FUNCTION 1 FB Feedback input 2 IN+ Non-inverting input 3 IN- Inverting input 4 REF 5 EN Enabled when this pin is floating or the applied voltage ≤ VS+ - 1.5 6 VS+ Positive supply voltage 7 VS- Negative supply voltage 8 OUT Output voltage Sets the common mode output voltage level to VREF 1, 5, 9 REF1, 2, 3 Reference input, controls common-mode output voltage 2, 6, 10 INP1, 2, 3 Non-inverting inputs 3, 7, 11 INN1, 2, 3 Inverting inputs 4, 8, 12, 18, 21, 24 NC 13, 16, 22 OUT1, 2, 3 14, 17, 23 FB1, 2, 3 15 EN 19 VSN Negative supply 20 VSP Positive supply 5 No connect, grounded for best crosstalk performance Non-inverting outputs Feedback from outputs Enabled when this pin is floating or the applied voltage ≤ VS+ - 1.5 FN7306.6 Connection Diagrams RG RF=0Ω -5V 1 FB VOUT OUT 8 2 INP VSN 7 INN 3 INN VSP 6 REF 4 REF EN 5 RL 500Ω 6 INP CL 2.7pF RS2 50Ω RS2 50Ω RS3 50Ω EL5175 EN +5V REF1 1 REF1 NC 24 INP1 2 INP1 FB1 23 INN1 3 INN1 OUT1 22 +5V RF OUT1 CL1 2.7pF NC 21 4 NC REF2 5 REF2 VSP 20 INP2 6 INP2 VSN 19 INN2 7 INN2 NC 18 RL1 500Ω RG RF FB2 17 8 NC REF3 9 REF3 OUT2 OUT2 16 INP3 10 INP3 EN 15 INN3 11 INN3 FB3 14 RL2 500Ω RG RF RSP1 50Ω RSN1 50Ω RSR1 50Ω RSP2 50Ω RSN2 50Ω RSR2 50Ω RSP3 50Ω RSN3 50Ω RSR3 50Ω 12 NC OUT3 OUT3 13 EL5175 -5V ENABLE CL2 2.7pF CL3 2.7pF RL3 500Ω EL5175, EL5375 RG FN7306.6 EL5175, EL5375 4 4 AV=1 RL=500Ω 2 CL=2.7pF AV=1 RL=100Ω 2 CL=2.7pF MAGNITUDE (dB) MAGNITUDE (dB) Typical Performance Curves VS=±5V 0 VS=±2.5V -2 -4 -6 1M 0 VS=±5V -4 10M 100M -6 1M 1G FREQUENCY (Hz) VS=±5V RL=500Ω 3 AV=1 MAGNITUDE (dB) NORMALIZED GAIN (dB) 5 VS=±5V RL=500Ω 2 CL=2.7pF AV=1 0 AV=5 AV=10 AV=2 -4 100M 1 -1 -5 1M 1G CL=2.7pF CL=0pF 10M 100M 1G FREQUENCY (Hz) FIGURE 3. FREQUENCY RESPONSE vs VARIOUS GAIN FIGURE 4. FREQUENCY RESPONSE vs CL 5 4 VS=±2.5V RL=500Ω 3 AV=1 CL=15pF NORMALIZED GAIN (dB) MAGNITUDE (dB) CL=15pF -3 10M 1G CL=10pF FREQUENCY (Hz) CL=10pF 1 -1 CL=2.7pF -3 -5 1M 100M FIGURE 2. FREQUENCY RESPONSE vs SUPPLY VOLTAGE 4 -6 1M 10M FREQUENCY (Hz) FIGURE 1. FREQUENCY RESPONSE vs SUPPLY VOLTAGE -2 VS=±2.5V -2 CL=0pF 10M 100M FREQUENCY (Hz) FIGURE 5. FREQUENCY RESPONSE vs CL 7 1G VS=±5V RL=500Ω 2 AV=2 CL=2.7pF RF=1kΩ RF=806Ω 0 -2 RF=500Ω RF=200Ω -4 -6 1M 10M 100M 1G FREQUENCY (Hz) FIGURE 6. FREQUENCY RESPONSE FOR VARIOUS RF FN7306.6 EL5175, EL5375 4 60 90 RL=500Ω AV=1 2 CL=2.7pF 40 0 20 -90 0 -180 -20 -270 0 VS=±5V VS=±2.5V -2 -4 -6 1M 10M 100M 1G -40 10K 100K FREQUENCY (Hz) 1M 10M PHASE (°) (Continued) GAIN (dB) NORMALIZED GAIN (dB) Typical Performance Curves -360 1G 100M FREQUENCY (Hz) FIGURE 7. FREQUENCY RESPONSE FOR VREF FIGURE 8. OPEN LOOP GAIN 100 30 10 PSRR (dB) IMPEDANCE (Ω) 10 -10 -30 PSRR+ -50 1 -70 0.1 10K 100K 1M 10M PSRR- -90 10K 100M 100K FIGURE 9. OUTPUT IMPEDANCE vs FREQUENCY 100M VOLTAGE NOISE (nV/√Hz), CURRENT NOISE (pA/√Hz) 1K 100 CMRR (dB) 10M FIGURE 10. PSRR vs FREQUENCY 120 80 60 40 20 -90 1K 1M FREQUENCY (Hz) FREQUENCY (Hz) 10K 100K 1M 10M 100M FREQUENCY (Hz) FIGURE 11. CMRR vs FREQUENCY 8 1G 100 EN 10 IN 1 10 100 1K 10K 100K 1M 10M FREQUENCY (Hz) FIGURE 12. VOLTAGE AND CURRENT NOISE vs FREQUENCY FN7306.6 EL5175, EL5375 Typical Performance Curves (Continued) 0 -40 VS=±5V f=5MHz -50 R =500Ω L DISTORTION (dB) GAIN (dB) -20 -40 -60 CH1↔CH2, CH2↔CH3 CH1↔CH3 -80 -100 100K 2) (AV= HD2 -60 =1) HD2 (AV -70 =2) HD3 (AV -80 -90 H ( D3 =1 AV ) -100 1M 10M 100M 1 1G 3 2 7 6 VOP-P (V) FREQUENCY (Hz) FIGURE 13. CHANNEL ISOLATION vs FREQUENCY (EL5375 ONLY) FIGURE 14. HARMONIC DISTORTION vs OUTPUT VOLTAGE -50 -50 -60 HD2 (AV=1) -70 H D3 -80 (AV = 2) VS=±5V -90 f=5MHz HD3 (AV=1) VOP-P=1V (AV=1) VOP-P=2V (AV=2) -100 100 200 300 400 500 600 700 800 900 2 HD -60 HD2 (AV=2) DISTORTION (dB) DISTORTION (dB) 5 4 =2) (A V =1) HD2 (AV -70 3 HD =2) (A V -80 HD =1) 3 (A V VS=±5V RL=500Ω VOP-P=1V (AV=1) VOP-P=2V (AV=2) -90 -100 1K 0 RLOAD (Ω) FIGURE 15. HARMONIC DISTORTION vs LOAD RESISTANCE 50mV/DIV 5 10 15 20 25 30 35 40 RLOAD (Ω) FIGURE 16. HARMONIC DISTORTION vs FREQUENCY 0.5V/DIV 10ns/DIV FIGURE 17. SMALL SIGNAL TRANSIENT RESPONSE 9 10ns/DIV FIGURE 18. LARGE SIGNAL TRANSIENT RESPONSE FN7306.6 EL5175, EL5375 Typical Performance Curves (Continued) M=100ns CH1=200mV/DIV CH2=5V/DIV M=400ns CH1=200mV/DIV CH2=5V/DIV CH1 CH1 CH2 CH2 100ns/DIV 400ns/DIV FIGURE 19. ENABLED RESPONSE JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 1 870mW QSOP24 θJA=115°C/W 0.8 625mW 0.6 SO8 θJA=160°C/W 0.4 486mW MSOP8 θJA=206°C/W 0.2 JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 1.4 POWER DISSIPATION (W) POWER DISSIPATION (W) 1.2 FIGURE 20. DISABLED RESPONSE 0 1.2 1.136W QSOP24 θJA=88°C/W 1 909mW SO8 θJA=110°C/W 0.8 870mW 0.6 MSOP8 θJA=115°C/W 0.4 0.2 0 0 25 50 75 85 100 125 150 0 AMBIENT TEMPERATURE (°C) 25 50 75 85 100 125 150 AMBIENT TEMPERATURE (°C) FIGURE 21. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE FIGURE 22. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE Simplified Schematic VS+ I1 I2 RD1 I3 I4 RD2 R3 R4 Q8 VIN+ Q1 VINQ2 VREF Q3 FB Q4 Q7 VB1 Q9 x1 VOUT Q6 25 VB2 CC R1 R2 VS- 10 FN7306.6 EL5175, EL5375 Description of Operation and Application Information Product Description The EL5175 and EL5375 are wide bandwidth, low power and single/differential ended to single ended output amplifiers. The EL5175 is a single channel differential to single ended amplifier. The EL5375 is a triple channel differential to single ended amplifier. The EL5175 and EL5375 are internally compensated for closed loop gain of +1 of greater. Connected in gain of 1 and driving a 500Ω load, the EL5175 and EL5375 have a -3dB bandwidth of 550MHz. Driving a 150Ω load at gain of 2, the bandwidth is about 130MHz. The bandwidth at the REF input is about 450MHz. The EL5175 and EL5375 is available with a power down feature to reduce the power while the amplifier is disabled. Input, Output, and Supply Voltage Range The EL5175 and EL5375 have been designed to operate with a single supply voltage of 5V to 10V or a split supplies with its total voltage from 5V to 10V. The amplifiers have an input common mode voltage range from -4.3V to 3.3V for ±5V supply. The differential mode input range (DMIR) between the two inputs is about from -2.3V to +2.3V. The input voltage range at the REF pin is from -3.6V to 3.3V. If the input common mode or differential mode signal is outside the above-specified ranges, it will cause the output signal distorted. The output of the EL5175 and EL5375 can swing from -3.9V to 3.5V at 500Ω load at ±5V supply. As the load resistance becomes lower, the output swing is reduced respectively. Over All Gain Settings The gain setting for the EL5175 and EL5375 is similar to the conventional operational amplifier. The output voltage is equal to the difference of the inputs plus VREF and then times the gain. RF ⎞ ⎛ V O = ( V IN + – V IN - + V REF ) × ⎜ 1 + --------⎟ R ⎝ G⎠ EN VIN+ VIN- + Σ VREF FB G/B + RF VO Choice of Feedback Resistor and Gain Bandwidth Product For applications that require a gain of +1, no feedback resistor is required. Just short the OUT+ pin to FBP pin and OUT- pin to FBN pin. For gains greater than +1, the feedback resistor forms a pole with the parasitic capacitance at the inverting input. As this pole becomes smaller, the amplifier's phase margin is reduced. This causes ringing in the time domain and peaking in the frequency domain. Therefore, RF has some maximum value that should not be exceeded for optimum performance. If a large value of RF must be used, a small capacitor in the few Pico farad range in parallel with RF can help to reduce the ringing and peaking at the expense of reducing the bandwidth. The bandwidth of the EL5175 and EL5375 depends on the load and the feedback network. RF and RG appear in parallel with the load for gains other than +1. As this combination gets smaller, the bandwidth falls off. Consequently, RF also has a minimum value that should not be exceeded for optimum bandwidth performance. For gain of +1, RF = 0 is optimum. For the gains other than +1, optimum response is obtained with RF between 500Ω to 1kΩ. For AV = 2 and RF = RG = 806Ω, the BW is about 190MHz and the frequency response is very flat. The EL5175 and EL5375 have a gain bandwidth product of 200MHz. For gains ≥5, its bandwidth can be predicted by the following equation: Gain × BW = 200MHz Driving Capacitive Loads and Cables The EL5175 and EL5375 can drive 15pF capacitance in parallel with 500Ω load to ground with less than 4.5dB of peaking at gain of +1. If less peaking is desired in applications, a small series resistor (usually between 5Ω to 50Ω) can be placed in series with each output to eliminate most peaking. However, this will reduce the gain slightly. If the gain setting is greater than 1, the gain resistor RG can then be chosen to make up for any gain loss which may be created by the additional series resistor at the output. When used as a cable driver, double termination is always recommended for reflection-free performance. For those applications, a back-termination series resistor at the amplifier's output will isolate the amplifier from the cable and allow extensive capacitive drive. However, other applications may have high capacitive loads without a back-termination resistor. Again, a small series resistor at the output can help to reduce peaking. Disable/Power-Down RG FIGURE 23. 11 The EL5175 and EL5375 can be disabled and placed its outputs in a high impedance state. The turn off time is about 1.2µs and the turn on time is about 80ns. When disabled, the amplifier's supply current is reduced to 80µA for IS+ and FN7306.6 EL5175, EL5375 120µA for IS- typically, thereby effectively eliminating the power consumption. The amplifier's power down can be controlled by standard CMOS signal levels at the ENABLE pin. The applied logic signal is relative to VS+ pin. Letting the EN pin float or applying a signal that is less than 1.5V below VS+ will enable the amplifier. The amplifier will be disabled when the signal at EN pin is above VS+ - 0.5V. If a TTL signal is used to control the enabled/disabled function, Figure 22 could be used to convert the TTL signal to CMOS signal. V OUT PD MAX = V S × I SMAX + ( V S + – V OUT ) × -------------------- × i R LOAD For sinking: PD MAX = [ V S × I SMAX + ( V OUT – V S - ) × I LOAD ] × i Where: 5V • VS = Total supply voltage 10K EN 1K For sourcing: • ISMAX = Maximum quiescent supply current per channel • VOUT = Maximum output voltage of the application CMOS/TTL • RLOAD = Load resistance • ILOAD = Load current FIGURE 24. Output Drive Capability The EL5175 and EL5375 have internal short circuit protection. Its typical short circuit current is ±67mA. If the output is shorted indefinitely, the power dissipation could easily increase such that the part will be destroyed. Maximum reliability is maintained if the output current never exceeds ±60mA. This limit is set by the design of the internal metal interconnections. Power Dissipation With the high output drive capability of the EL5175 and EL5375. It is possible to exceed the 135°C absolute maximum junction temperature under certain load current conditions. Therefore, it is important to calculate the maximum junction temperature for the application to determine if the load conditions or package types need to be modified for the amplifier to remain in the safe operating area. The maximum power dissipation allowed in a package is determined according to: T JMAX – T AMAX PD MAX = --------------------------------------------Θ JA • TJMAX = Maximum junction temperature • TAMAX = Maximum ambient temperature • θJA = Thermal resistance of the package • i = Number of channels By setting the two PDMAX equations equal to each other, we can solve the output current and RLOAD to avoid the device overheat. Power Supply Bypassing and Printed Circuit Board Layout As with any high frequency device, a good printed circuit board layout is necessary for optimum performance. Lead lengths should be as sort as possible. The power supply pin must be well bypassed to reduce the risk of oscillation. For normal single supply operation, where the VS- pin is connected to the ground plane, a single 4.7µF tantalum capacitor in parallel with a 0.1µF ceramic capacitor from VS+ to GND will suffice. This same capacitor combination should be placed at each supply pin to ground if split supplies are to be used. In this case, the VS- pin becomes the negative supply rail. For good AC performance, parasitic capacitance should be kept to minimum. Use of wire wound resistors should be avoided because of their additional series inductance. Use of sockets should also be avoided if possible. Sockets add parasitic inductance and capacitance that can result in compromised performance. Minimizing parasitic capacitance at the amplifier's inverting input pin is very important. The feedback resistor should be placed very close to the inverting input pin. Strip line design techniques are recommended for the signal traces. Assume the REF pin is tired to GND for VS = ±5V application, the maximum power dissipation actually produced by an IC is the total quiescent supply current times the total power supply voltage, plus the power in the IC due to the load, or: 12 FN7306.6 EL5175, EL5375 Typical Applications 0Ω 50 VFB 50Ω VIN EL5173/ EL5373 50 VINB EL5175/ EL5375 VOUT 50Ω ZO = 100Ω VREF FIGURE 25. TWISTED PAIR CABLE RECEIVER As the signal is transmitted through a cable, the high frequency signal will be attenuated. One way to compensate this loss is to boost the high frequency gain at the receiver side. R3 R1 R2 Gain (dB) C1 1 + R2 / R 1 VFB 50Ω VIN VINB ZO = 100Ω EL5175/ EL5375 VOUT 1 + R2 / (R1 + R3) 50Ω VREF fA fC f FIGURE 26. COMPENSATED LINE RECEIVER Level Shifter and Signal Summer The EL5175 and EL5375 contains two pairs of differential pair input stages. It makes the inputs are all high impedance inputs. To take advantage of the two high impedance inputs, the EL5175 and EL5375 can be used as a signal summer to add two signals together. Like, one signal can be applied to VIN+, the second signal can be applied to REF and VIN- is ground. The output is equal to: V O = ( V IN + + V REF ) × Gain Also, the EL5175 and EL5375 can be used as a level shifter by applying a level control signal to the REF input. 13 FN7306.6 EL5175, EL5375 Small Outline Package Family (SO) A D h X 45° (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL “X” 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4° ±4° DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300”) (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 ±0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 ±0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 ±0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 ±0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 ±0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 ±0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 ±0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 ±0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150”) 8 14 16 Rev. M 2/07 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 14 FN7306.6 EL5175, EL5375 Mini SO Package Family (MSOP) 0.25 M C A B D MINI SO PACKAGE FAMILY (N/2)+1 N E MDP0043 A E1 MILLIMETERS PIN #1 I.D. 1 B (N/2) e H C SEATING PLANE 0.10 C N LEADS SYMBOL MSOP8 MSOP10 TOLERANCE NOTES A 1.10 1.10 Max. - A1 0.10 0.10 ±0.05 - A2 0.86 0.86 ±0.09 - b 0.33 0.23 +0.07/-0.08 - c 0.18 0.18 ±0.05 - D 3.00 3.00 ±0.10 1, 3 E 4.90 4.90 ±0.15 - E1 3.00 3.00 ±0.10 2, 3 e 0.65 0.50 Basic - L 0.55 0.55 ±0.15 - L1 0.95 0.95 Basic - N 8 10 Reference - 0.08 M C A B b Rev. D 2/07 NOTES: 1. Plastic or metal protrusions of 0.15mm maximum per side are not included. L1 2. Plastic interlead protrusions of 0.25mm maximum per side are not included. A 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. c SEE DETAIL "X" A2 GAUGE PLANE L A1 0.25 3° ±3° DETAIL X 15 FN7306.6 EL5175, EL5375 Quarter Size Outline Plastic Packages Family (QSOP) MDP0040 A QUARTER SIZE OUTLINE PLASTIC PACKAGES FAMILY D (N/2)+1 N INCHES SYMBOL QSOP16 QSOP24 QSOP28 TOLERANCE NOTES E PIN #1 I.D. MARK E1 1 (N/2) A 0.068 0.068 0.068 Max. - A1 0.006 0.006 0.006 ±0.002 - A2 0.056 0.056 0.056 ±0.004 - b 0.010 0.010 0.010 ±0.002 - c 0.008 0.008 0.008 ±0.001 - D 0.193 0.341 0.390 ±0.004 1, 3 E 0.236 0.236 0.236 ±0.008 - E1 0.154 0.154 0.154 ±0.004 2, 3 e 0.025 0.025 0.025 Basic - L 0.025 0.025 0.025 ±0.009 - L1 0.041 0.041 0.041 Basic - N 16 24 28 Reference - B 0.010 C A B e H C SEATING PLANE 0.007 0.004 C b C A B Rev. F 2/07 NOTES: L1 A 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. c SEE DETAIL "X" 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. 0.010 A2 GAUGE PLANE L A1 4°±4° DETAIL X All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16 FN7306.6