Negative Buck Converter with Short-Circuit Protection and Shutdown Design Note 1022 Victor Khasiev Introduction Negative buck converters are increasingly used to “step down” (by absolute value) negative voltages. The main reason behind the increasing demand is the standardization of switching transformers, which are typically produced with one or two secondary windings. For example, if a system employs a transformer with two secondary windings to produce ±12V, and the design also requires –3.3V, engineers tend to lean toward solutions, such as a negative buck, that don’t require changing the main transformer. Circuit Description and Performance Figure 1 shows a negative buck converter that generates –3.3V at 3A from a –12V rail. The power train includes inductor L1, diode D1 and MOSFET Q1. The LTC3805-5 controller IC includes a complete set of essential functions including short-circuit protection (the current level can be precisely set), converter enable/disable, and programmable switching frequency. An internal shunt regulator allows biasing the IC directly from the input rail. Despite the simplicity of the topology, which makes it an attractive choice for many designers, there are two important design considerations in a negative buck converter: sensing the output voltage and remote shutdown. The controller is referenced to the negative voltage, yet the output voltage and ON/OFF signal are referenced to the system ground (see Figure 1). To close the regulation loop, a current mirror based on transistor Q3 is used. Resistor RPRG programs the current flowing into resistor RFB, which sets the output voltage. In this example, when the output voltage is equal to –3.3V, the 3.31k RPRG resistor sets the current into resistor RFB at 1mA. This current creates a 0.8V drop across resistor RFB, which is equal to the reference voltage of the internal error amplifier. L, LT, LTC, LTM, Linear Technology, the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. R8 4.99k ON OFF 5V 0V 4 5 3 R12 511k R9 10k 1 GND 2 6 GND R11 1k Q2 MBT3906DW1T1 C2 0.1μF R10 511k C1 0.1μF 1 2 C3 2.2nF R5 15k 3 4 5 R7 100k –12V INPUT GND CIN 10μF RFB 800 LTC3805-5 SSFLT GATE ITH VCC FB OC RUN FS ISENSE SYNC GND R4 316 8 OUT 330μF RPRG 3.31k VOUT –3.3V AT 3A MBT39069W171 4 5 Q1 HAT2165H 10 9 D1 PDS1040 L1 6μH +C R3 1k 3 2 1 6 7 6 R2 3.12k R1 0.015 31.1k –12V INPUT Figure 1. A Negative Buck Converter Based on the LTC3805 Produces –3.3V at 3A from a –10V to –14V Input 09/11/1022 The optional shut-down circuit is based on transistor Q2. If 5V is applied to resistor R8, the LTC3805-5 shuts down. Both circuits are referenced to the system ground. The voltage stress on the power train components, transfer function and other parameters are similar to the wellknown buck converter. The efficiency is about 90%, as shown Figure 2. The load characteristic is shown in Figure 3. At loads exceeding 4.5A, the output voltage begins to drop and at 5.0A the converter enters into a short-circuit protection state. In this state, the input current does not exceed 20mA. The output voltage recovers after the short circuit is removed. Line and load regulation are better than ±1% over a wide –40°C to 70°C temperature range. Waveforms of the start-up and transient response for the circuit in Figure 1 are shown in Figures 4 and 5, respectively. Conclusion Negative buck converters are a popular way to produce additional negative rails from a standard –12V rail. The solution shown here produces –3.3V at 3A from a –12V rail with a design that features high efficiency, overcurrent protection, fast transient response and a smooth start-up. References Erickson, Robert, W, Fundamentals of Power Electronics, 2nd edition, ISBN 0-7923-7270-0 Efficiency vs Load 92 10V 12V 14V 91 10ms/DIV EFFICIENCY (%) 90 VOUT (1V/DIV) 89 88 87 86 85 84 1.5 2.0 2.5 OUTPUT CURRENT (A) 1 3.0 Figure 4. Start-Up into Full Load Figure 2. Efficiency vs Input Voltage and Output Current Overcurrent Protection 3.5 VIN = –12V OUTPUT VOLTAGE (V) 1ms/DIV 3.0 VOUT 100mV/DIV IOUT 1A/DIV 2.5 2.0 1.5 3 3.5 4.0 4.5 5.0 OUTPUT CURRENT (A) 5.5 Figure 3. Output Voltage vs Output Current, with a –12V Input Voltage Data Sheet Download www.linear.com Figure 5. Transient Response for a Load Current Step from 1A to 2.5A For applications help, call (408) 432-1900, Ext. 2134 Linear Technology Corporation dn1022 LT 0911 • PRINTED IN THE USA FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2011 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ●