Toggles Series SK Rockers General Specifications Pushbuttons Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V AC for low & medium security; 1A @ 250V AC for low security Other Ratings Slides Rotaries Keylocks Programmable Illuminated PB Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Torque: Contact Timing: Angle of Throw: F Materials & Finishes Key: Tumbler Barrel: Housing/Bushing: Base: Movable Contactor: Stationary Contacts: Terminals: Indicators Touch Tilt Tactiles Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: 10 milliohms maximum 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 30,000 cycles minimum 10,000 cycles minimum .026Nm (.234 lb•in) for low & medium security Break-before-make 90° for 2-position & 45° for 3-position Zinc alloy with chrome plating (matte) for low security models; brass with nickel plating (shiny) for medium security models Zinc alloy with chrome plating (matte) for low security models; zinc alloy with chrome plating (shiny) for medium security models Zinc alloy with chrome plating (matte) for low security models; zinc alloy with chrome plating (shiny) for medium security models Phenolic resin (thermoset) Silver Silver capped copper with silver plating Copper or brass with silver plating –25°C through +70°C (–13°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Mounting Torque: 1.5Nm (13.28 lb • in) maximum Soldering Time & Temperature: Manual Soldering: See Profile A in Supplement section. Standards & Certifications UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” to end of part number to order UL recognized switch. All low security models recognized at 3A @ 125V AC or 1A @ 250V AC & all medium security models recognized at 3A @ 125V AC CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” to end of part number to order CSA certified switch. All low security models certified at 3A @ 125V AC or 1A @ 250V AC Supplement Accessories Low & Medium Security Keylocks F10 www.nkk.com Toggles Series SK Rockers Distinctive Characteristics Pushbuttons 12mm diameter bushing for easy panel cutout preparation and high density mounting. Programmable Illuminated PB Epoxy sealed terminals prevent entry of flux and other contaminants. Short behind panel dimension - only 1.063” (27.0mm). High dielectric strength of 1,500 volts between contacts and case. F Rotaries Detent mechanism gives crisp, positive action for accurate switch setting. Keylocks Low & Medium Security Keylocks Tilt Tactiles Slides Dust resistant interior construction protects contacts. Supplement Accessories Indicators Touch Actual Size www.nkk.com F11 Series SK Toggles Low & Medium Security Keylocks TYPICAL SWITCH ORDERING EXAMPLE 1 Pushbuttons Rockers SK A Programmable Illuminated PB Poles 1 W 01 Lock Mechanisms SPDT Terminals A Low Security D Medium Security (not combinable with code 3D circuit) 01 Pos. 1 Pos. 2 Pos. 3 Key Removes 2A ON NONE ON Positions 1 and 3 2B ON NONE ON Position 1 3D ON OFF ON Positions 1, 2, 3 3E ON OFF ON Position 2 W Silver Rated 3A @ 125V AC Slides Code Tactiles DESCRIPTION FOR TYPICAL ORDERING EXAMPLE SK12BAW01 Tilt Silver Contacts Rated 3A @ 125V AC Solder Lug Terminals Low Security Lock Mechanism 2 keys supplied with each switch Indicators Touch SPDT ON-NONE-ON Circuit Key Removable in Position 1 Accessories IMPORTANT: Supplement Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on General Specifications page. F12 www.nkk.com Solder Lug * *Wire harness & cable assemblies offered only in Americas Contact Material Circuits & Key-Removable Positions F Rotaries Keylocks 2B Toggles Series SK Low & Medium Security Keylocks POLES, CIRCUITS & KEY-REMOVABLE POSITIONS Connected Terminals Model Pos 1 Pos 2 Pos 3 Pos 1 SPDT SK12A ON NONE ON COM-1 = Key Removable (Terminal numbers are on switch) Pos 2 Pos 3 Schematic • = Not Removable = Maximum Arc Rockers Key Positions Pole & Throw POS 1 ____ COM-2 COM SK12B ON NONE ON COM-1 ____ COM-2 1 2 3 ON OFF ON COM-1 OPEN COM-2 SPDT SK13E ON OFF ON COM-1 OPEN COM-2 POS 1 COM 1 3 Programmable Illuminated PB *SK13D OP E N SPDT 2 2 POS 1 2 3 * Available with low security only KEY REMOVABLE Positions 1 & 3 90° Angular Throw B Position 1 90° Angular Throw D Positions 1, 2 & 3 45° Angular Throw E Position 2 45° Angular Throw LOCK MECHANISMS & KEYS Slides Medium Security Mechanism Zinc Alloy with Chrome Plating (matte finish) Brass with Nickel Plating (shiny finish) Two keys provided with each switch (no master key available) One key provided with each switch (no master key available) For ordering additional keys: AT4081 for SK12A and SK12B, marked “1201” AT4082 for SK13D and SK13E, marked “1301” For ordering additional keys, indicate the same key number that is engraved on the face of your switch. Tilt Key numbers (001 through 010) randomly assigned. Typical Key Ordering Example: AT4124-001 (17.0) .669 Touch AT4081 Tactiles D Low Security Mechanism (9.4) .370 AT4082 (17.0) .669 (20.0) .787 (16.2) .638 (14.2) .559 (1.8) .071 Accessories (1.8) .071 Indicators (14.2) .559 (1.8) .071 (9.4) .370 www.nkk.com (13.7) .539 Supplement A F Rotaries A Keylocks SPDT Pushbuttons 3 POS 1 F13 Series SK Toggles Low & Medium Security Keylocks CONTACT MATERIALS, RATINGS, & TERMINALS Rockers W Silver over Silver Power Level 3A @ 125V AC (4.5) .177 Epoxy Seal (2.0) .079 (1.1) .043 Thk = (0.8) .031 Solder Lug Terminals TYPICAL SWITCH DIMENSIONS Low Security • 90° Angular Throw (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 M12 P1 90° POS 3 F (17.0) .669 M (0.5) .020 (2.0) Typ .079 (3.0) .118 (13.2) .520 (14.0) Dia .551 Rotaries 1 2 POS 1 CO Keylocks Programmable Illuminated PB Pushbuttons 01 (2.0) .079 (4.5) .177 (13.0) .512 (10.8) .425 (30.0) 1.181 Slides SK12BAW01 POS 2 45° 45° (17.0) .669 (0.5) .020 Touch SK13EAW01 Supplement Accessories Indicators www.nkk.com 2 M F14 (0.8) Typ .031 (3.0) .118 (13.2) .520 (14.0) Dia .551 O Tilt POS 3 C POS 1 (1.1) x (2.0) Typ .043 x .079 (2.0) Typ .079 M12 P1 1 Tactiles Low Security • 45° Angular Throw (13.0) .512 (30.0) 1.181 (4.5) .177 (10.8) .425 Series SK Toggles Low & Medium Security Keylocks TYPICAL SWITCH DIMENSIONS 90° 005 005 (13.0) .512 (4.5) .177 (32.7) 1.287 Programmable Illuminated PB (10.0) (3.5) .394 .138 (15.3) .602 (15.0) Dia .591 Rockers M (2.0) Typ .079 (10.8) .425 SK12ADW01 Medium Security • 45° Angular Throw (0.75) .0295 (15.0) Dia .591 F CO POS 3 (20.0) .787 M (2.0) Typ .079 (10.0) (3.5) .394 .138 (15.3) .602 (13.0) .512 (32.7) 1.287 (4.5) .177 Rotaries 45° 006 006 (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 M12 P1 45° POS 2 1 2 POS 1 (10.8) .425 SK13EDW01 . Tactiles PANEL CUTOUT & THICKNESS Slides (20.0) .787 (0.75) .0295 CO POS 3 Pushbuttons (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 M12 P1 1 2 POS 1 Medium Security • 90° Angular Throw Keylocks (12.0) Dia .472 Tilt The 12mm bushing is .512” (13.0mm) long. It allows mounting these devices in a maximum effective panel thickness of .315” (8.0mm). Touch (11.2) .441 AT508 Internal Tooth Lockwasher (12.1) .476 (14.0) .551 (15.8) Dia .622 1 included with each switch 1 included with each switch Steel with nickel plating Steel with zinc/chromate plating (16.0) .630 (13.8) Dia .543 (1.0) .039 (2.0) .079 www.nkk.com Accessories M12 P1 (0.5) .020 Supplement AT527M Hex Mounting Nut Indicators STANDARD HARDWARE F15