A Fully Illuminated Toggles General Specifications Electrical Capacity (Resistive Load) Power Level (silver): Logic Level (gold): Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Static Capability: Nominal Operating Force: Angle of Throw: Materials & Finishes Toggle: Housing: Sealing Ring: Base: Movable Contactor: Movable Contacts: Stationary Contact: Lamp Contacts: Power Terminals: Lamp Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: 6A @ 125V AC or 3A @ 250V AC or 6A @ 12V DC for silver 0.4VA maximum @ 28V AC/DC maximum for gold (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: See Supplement Index for explanation of operating range. 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum for silver; 50,000 operations minimum for gold Withstands 20 kilovolts ESD minimum 1.9N for .689” (17.5mm) toggle; 2.5N for .433” (11.0mm) toggle 25° Polycarbonate Glass fiber reinforced polyamide Nitrile butadiene rubber Diallyl phthalate (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy or copper with gold plating Silver plus copper with silver plating or copper with gold plating Beryllium copper with silver plating Copper with silver or gold plating Brass with silver plating –10°C through +55°C (+14°F through +131°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 1.75 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Mounting Torque: .98Nm (8.67 lb • in) maximum Soldering Time & Temperature: Manual Soldering: See Profile B in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 base Supplement Accessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series TL A118 www.nkk.com A Rockers Distinctive Characteristics Toggles Series TL Fully Illuminated Toggles Programmable Illuminated PB Pushbuttons Choice of long or short toggles in translucent colors combine with bright LEDs available in red, amber, and green, plus super bright LEDs available in white, green, and blue. Black face nut enhances front panel appearance. Antistatic material used for toggle withstands 20 kilovolts electrostatic discharge. Rotaries Keylocks Panel seal, achieved with use of optional exterior o-ring, conforms to IP65 of IEC60529 Standards. Slides Interior o-ring protects contacts from oil, dust, water, and other contaminants. Tactiles UL94V-0 flammability rated for base. High insulating barriers protect against crossover. Tilt Terminals are molded in and epoxy sealed to lock out flux, dust, and other contaminants. Supplement Accessories Indicators Touch Actual Size www.nkk.com A119 TYPICAL SWITCH ORDERING EXAMPLE Pushbuttons 2 TL D 2 Pole 2 N A Toggle Colors For Bright DPDT Circuit 2 ON NONE Keylocks Programmable Illuminated PB Fully Illuminated Toggles A Rockers Toggles Series TL W01 Housing A 5C Red D Amber 5D Amber F Green 5F Green N Super Bright No Color Rotaries S .433” (11.0mm) (combines with gold contacts only) Tilt Touch Indicators 6G Blue Solder Lug Terminals Gold 0.4VA @ 28V AC/DC for .433” (11.0mm) Toggle only Black Housing Silver Contacts with 6-amp Rating Supplement Green G01 Blue, Super Bright LED www.nkk.com 6F Solder Lug Terminals Silver 6A @ 125V AC for .689” (17.5mm) Toggle only .689” (17.5mm) Toggle Length; No Color (matte finish of clear material) Solder Lug Terminals White W01 TL22DNAW016G DPDT ON-NONE-ON Circuit 6B Terminals, Contacts & Ratings Tactiles Slides D .689” (17.5mm) (combines with silver contacts only) DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Accessories Bright Black Red Toggle Lengths A120 LED Colors C For Super Bright ON 6G A POLE & CIRCUIT Center Up OPEN 1-1a 2-2a ON NONE ON 1-1b 2-2b DPDT 1 1a (COM) 2 2a 1b Rockers Notes: Terminal numbers are not actually on switch. Lamp circuit is isolated and requires an external power source. 2b (+) (-) TOGGLE LENGTHS & COLORS .689” (17.5mm) Combines with Silver Contacts only S (17.5) .689 .433” (11.0mm) Colors Available for Bright LED Combines with Gold Contacts only Material: Polycarbonate C (11.0) .433 D Red Amber F Green Color Available for Super Bright LED Material: Polycarbonate No Color (Appearance is matte finish of clear material) N Keylocks D HOUSING A Black The diallyl phthalate material used for the base is UL flammability rated 94V-0; housing material is not. The housing consists of the one-piece bushing/case of glass fiber reinforced polyamide in black color only. CONTACT MATERIALS, RATINGS, & TERMINALS G Solder Lug (5.4) .213 Gold Contacts Logic Level 0.4VA maximum @ 28V AC/DC Exopy Seal See Supplement Index for complete explanation of operating range. (1.17) .046 Turret LED Thk = (0.6) .024 (5.0) .197 Slides 01 Terminals Silver Contacts Power Level 6A @ 125V AC & 3A @ 250V AC & 6A @ 12V DC (2.0) .079 (3.0) (3.5) .118 .138 (2.0) Typ .079 (1.1) Typ .043 Tactiles W Solder Lug Thk = (0.8) Typ .031 Tilt LED CODES & SPECIFICATIONS Colored Toggles ATTENTION ELECTROSTATIC SENSITIVE DEVICES Touch Electrical specifications are determined at a basic temperature of 25°C. Lamp circuit is independent of switch operation. If the source voltage is greater than rated voltage, a ballast resistor is required. The ballast resistor calculation and more lamp detail are shown in Supplement section. Super Bright LEDs are Electrostatic Sensitive Clear Toggles 5 Bright 6 Super Bright LED Factory Assembled Not Available Separately Color Maximum Forward Current I FM 30mA 30mA 50mA 30mA 30mA 30mA Typical Forward Current IF 20mA 20mA 20mA 20mA 20mA 20mA Forward Voltage VF 2.0V 2.1V 2.27V 3.3V 3.3V 3.3V Maximum Reverse Voltage VRM 4V 4V 4V 7V 7V 7V Current Reduction Rate Above 25°C ∆I F Ambient Temperature Range C Red D Pushbuttons Down Keyway Programmable Illuminated PB TL22 Up Rotaries DP Center Keyway Amber F Green B White F Green G Blue 0.32mA/°C 0.32mA/°C 0.50mA/°C 0.40mA/°C 0.40mA/°C 0.40mA/°C –10°C ~ +55°C www.nkk.com –10°C ~ +55°C A121 Indicators Model Throw & Power/Lamp Schematics Accessories Down Pole Connected Terminals Supplement Toggle Position Toggles Series TL Fully Illuminated Toggles Toggles Series TL Fully Illuminated Toggles A TYPICAL SWITCH DIMENSIONS Keyway Pushbuttons (1.1) x (2.0) Typ .043 x .079 (0.6) Typ .024 (3.5) .138 M12 P1 2b (4.7) Typ (13.5) .185 .531 (0.8) Typ .031 25° 1b v L( )I L ( ) vI Programmable Illuminated PB 2a (2.5) .098 (4.5) .177 (18.0) Sq .709 (6.0) Dia .236 (21.0) .827 (10.0) .394 (17.5) .689 (5.4) .213 1a (0.5) Typ .020 (2.0) Typ .079 (5.0) Typ .197 TL22DNAW016G 11.0mm Toggle Rotaries (1.17) Typ .046 2b v L( )I (4.7) Typ (13.5) .185 .531 (0.8) Typ .031 L ( ) vI 2a (2.5) .098 Slides (6.0) .236 (18.0) Sq .709 (21.0) .827 (10.0) .394 (11.0) .433 (5.4) .213 1b I Keylocks (1.1) x (2.0) Typ .043 x .079 (0.6) Typ .024 (3.5) .138 M12 P1 Keyway 25° 1a (0.5) Typ .020 (2.0) Typ .079 (5.0) Typ .197 TL22SCAG015C Tactiles STANDARD HARDWARE Tilt AT527MA Black Hex Nut Use as Face Nut Chrome/Steel OPTIONAL HARDWARE AT527M Hex Nut Use as Backup Nut Nickel/Steel AT508 Lockwasher Not to use with Panel Seal Steel with Chromate/Zinc AT401P O-ring Use for Panel Seal Nitrile butadiene rubber (12.1) .476 M12 P1 M12 P1 (14.0) .551 (15.8) Dia .622 Touch (14.0) .551 (12.1) Dia .476 (17.5) Dia .689 (13.8) Dia .543 Indicators (16.0) .630 (2.0) .079 (16.0) .630 (2.0) .079 (0.5) .020 (1.0) .039 (1.5) .059 Hardware details in Accessories & Hardware section. Panel Cutouts (12.5) Dia .492 Maximum Panel Thickness with Standard Hardware .157” (4.0mm) Supplement Accessories (1.17) Typ .046 I Rockers 17.5mm Toggle A122 (11.5) .453 (12.5) Dia .492 www.nkk.com (1.5) .060 Maximum Panel Thickness with Standard Hardware & AT401P O-ring .236” (6.0mm) Notes www.nkk.com A123