LTC2386-16 - 16-Bit, 10Msps SAR ADC

LTC2386-16
16-Bit, 10Msps SAR ADC
Features
Description
10Msps Throughput Rate
nn No Pipeline Delay, No Cycle Latency
nn 93.8dB SNR (Typ) at f = 1MHz
IN
nn 102dB SFDR (Typ) at f = 1MHz
IN
nn Nyquist Sampling Up to 5MHz Input
nn Guaranteed 16-Bit, No Missing Codes
nn ±0.5LSB INL (Max)
nn 8.192V
P-P Differential Inputs
nn 5V and 2.5V Supplies
nn Internal 20ppm/°C (Max) Reference
nn Serial LVDS Interface
nn 97mW Power Dissipation
nn 32-Pin (5mm × 5mm) QFN Package
The LTC®2386-16 is a low noise, high speed, 16-bit 10Msps
successive approximation register (SAR) ADC ideally
suited for a wide range of applications. The combination
of excellent linearity and wide dynamic range makes the
LTC2386-16 ideal for high speed imaging and instrumentation applications. No-latency operation provides a
unique solution for high speed control loop applications.
The very low distortion at high input frequencies enables
communications applications requiring wide dynamic
range and significant signal bandwidth.
nn
To support high speed operation while minimizing the
number of data lines, the LTC2386-16 features a serial
LVDS digital interface. The LVDS interface has one-lane
and two-lane output modes, allowing the user to optimize
the interface data rate for each application.
Applications
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
Protected by U.S. Patents, including 7705765, 8232905, 8810443. Other patents are pending.
High Speed Data Acquisition
nn Imaging
nn Communications
nn Control Loops
nn Instrumentation
nn ATE
nn
Typical Application
FFT, fSMPL = 10Msps, fIN = 2kHz
0.1µF
0V
4.096V
0V
0
0.1µF
VDDL
OVDD
CLK
DCO
DA
DB
IN+
+
–
2.5V
0.1µF
VDD
24.9Ω
4.096V
2.5V
180pF
LTC2386-16
180pF
24.9Ω
VCM
0.1µF
REFBUF REFGND
–40
LVDS
INTERFACE
TWOLANES
TESTPAT
PD
IN–
REFIN
GND
CNV
–60
–80
–100
–120
SAMPLE
CLOCK
0.1µF
10µF
SNR = 94.0dB
THD = –117dB
SINAD = 93.9dB
SFDR = 119dB
–20
AMPLITUDE (dBFS)
5V
238616 TA01a
–140
–160
0
1
2
3
FREQUENCY (MHz)
4
5
238616 TA01b
238616
For more information www.linear.com/LTC2386-16
1
LTC2386-16
Absolute Maximum Ratings
Pin Configuration
(Notes 1, 2)
TWOLANES
GND
CNV–
CNV+
GND
VDDL
VCM
VDDL
TOP VIEW
Supply Voltage (VDD)...................................................6V
Supply Voltage (VDDL, OVDD)....................................2.8V
Analog Input Voltage (Note 3)
IN+, IN–..........................(GND – 0.3V) to (VDD + 0.3V)
REFBUF..........................(GND – 0.3V) to (VDD + 0.3V)
REFIN (Note 4)............................(GND – 0.3V) to 2.8V
Digital Input Voltage (Note 3)
PD, TESTPAT.............. (GND – 0.3V) to (OVDD + 0.3V)
CLK+, CLK–................. (GND – 0.3V) to (OVDD + 0.3V)
TWOLANES, CNV+,
CNV–............................(GND – 0.3V) to (VDDL + 0.3V)
Power Dissipation............................................... 500mW
Operating Temperature Range
LTC2386C................................................. 0°C to 70°C
LTC2386I..............................................–40°C to 85°C
Storage Temperature Range................... –65°C to 150°C
32 31 30 29 28 27 26 25
GND 1
24 CLK+
+
2
23 CLK–
IN–
3
IN
22 OVDD
GND 4
21 GND
33
GND
REFGND 5
20 DCO+
REFGND 6
19 DCO–
REFBUF 7
18 DA+
REFBUF 8
17 DA–
DB+
DB
–
TESTPAT
PD
VDD
VDD
GND
REFIN
9 10 11 12 13 14 15 16
UH PACKAGE
32-LEAD (5mm × 5mm) PLASTIC QFN
TJMAX = 125°C, θJA = 34°C/W
EXPOSED PAD (PIN 33) IS GND, MUST BE SOLDERED TO PCB
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2386CUH-16#PBF
LTC2386CUH-16#TRPBF
238616
32-Lead (5mm × 5mm) Plastic QFN
0°C to 70°C
LTC2386IUH-16#PBF
LTC2386IUH-16#TRPBF
238616
32-Lead (5mm × 5mm) Plastic QFN
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through
designated sales channels with #TRMPBF suffix.
Electrical Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
VIN+
Absolute Input Range (IN+)
(Note 6)
l
–0.1
VREFBUF + 0.1
V
–
Absolute Input Range (IN–)
(Note 6)
l
–0.1
VREFBUF + 0.1
V
VIN+ – VIN–
Input Differential Voltage Range
VINCM
Common Mode Input Range
VIN+ – VIN–
(VIN+ + VIN–)/2
IIN
Analog Input DC Leakage Current
CIN
Analog Input Capacitance
Sample Mode
Hold Mode
20
2
pF
pF
CMRR
Input Common Mode Rejection Ratio
fIN = 1MHz
75
dB
VIN
MIN
l
–VREFBUF
l
VREFBUF/2 – 0.1
l
–1
TYP
VREFBUF/2
MAX
UNITS
VREFBUF
V
VREFBUF/2 + 0.1
V
1
μA
238616f
2
For more information www.linear.com/LTC2386-16
LTC2386-16
Converter Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
MAX
UNITS
l
16
Bits
No Missing Codes
l
16
Bits
l
–0.5
±0.15
0.5
LSB
l
–0.6
±0.06
0.6
LSB
l
–2.5
±0.4
2.5
LSB
Transition Noise
INL
Integral Linearity Error
DNL
Differential Linearity Error
ZSE
Zero-Scale Error
0.35
REFBUF = 4.096V (REFBUF Overdriven) (Notes 7, 9)
(Note 8)
Zero-Scale Error Drift
FSE
TYP
Resolution
LSBRMS
0.005
Full-Scale Error
REFBUF = 4.096V (REFBUF Overdriven) (Notes 8, 9)
REFIN = 2.048V (REFIN Overdriven) (Note 8)
Full-Scale Error Drift
REFBUF = 4.096V (REFBUF Overdriven) (Note 9)
REFIN = 2.048V (REFIN Overdriven)
l
l
–5
–40
±1.3
±7
LSB/°C
5
40
±0.1
±1.5
LSB
LSB
ppm/°C
ppm/°C
Dynamic Accuracy
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C and AIN = –1dBFS. (Notes 5, 10)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
SINAD
Signal-to-(Noise + Distortion) Ratio
fIN = 2kHz
fIN = 1MHz
fIN = 5MHz
SNR
Signal-to-Noise Ratio
THD
l
l
91.5
91.2
93.9
93.2
82.6
dB
dB
dB
fIN = 2kHz
fIN = 1MHz
fIN = 5MHz
l
l
91.6
91.4
94
93.8
93.1
dB
dB
dB
Total Harmonic Distortion
(First Five Harmonics)
fIN = 2kHz
fIN = 1MHz
fIN = 5MHz
l
l
SFDR
Spurious Free Dynamic Range
fIN = 2kHz
fIN = 1MHz
fIN = 5MHz
l
l
–117
–101
–83
107
97
–3dB Input Bandwidth
MAX
–108
–97
UNITS
dB
dB
dB
119
102
84
dB
dB
dB
200
MHz
Internal Reference Characteristics
The l denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VREFIN
Internal Reference Output Voltage
IOUT = 0μA
2.043
2.048
2.053
V
VREFIN Temperature Coefficient
(Note 11)
±5
±20
l
REFIN Output Impedance
VREFIN Line Regulation
VDD = 4.75V to 5.25V
REFIN Input Voltage Range
(REFIN Overdriven) (Note 6)
l
2.008
ppm/°C
15
kΩ
0.3
mV/V
2.048
2.088
V
238616
For more information www.linear.com/LTC2386-16
3
LTC2386-16
Reference Buffer Characteristics
The l denotes the specifications which apply over the full
operating temperature range, otherwise specifications are at TA = 25°C. (Note 5)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Reference Buffer Output Voltage VREFIN = 2.048V
l
4.090
4.096
4.102
V
REFBUF Input Voltage Range
(REFBUF Overdriven) (Notes 6, 9)
l
4.016
4.096
4.176
V
IREFBUF
REFBUF Load Current
VREFBUF = 4.096V (REFBUF Overdriven) (Notes 9, 12)
VREFBUF = 4.096V, Sleep Mode (REFBUF Overdriven) (Note 9)
l
1.2
0.5
1.5
VCM
Common Mode Output
VREFBUF = 4.096V, IOUT = 0μA
l
2.048
2.068
VCM Output Impedance
–1mA < IOUT < 1mA
VREFBUF
2.028
mA
mA
V
15
Ω
Digital Inputs and Digital Outputs
The l denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
PD, TESTPAT, TWOLANES
VIH
High Level Input Voltage
VDDL = OVDD = 2.5V
l
VIL
Low Level Input Voltage
VDDL = OVDD = 2.5V
l
IIN
Digital Input Current
VIN = 0V to 2.5V
l
CIN
Digital Input Capacitance
1.7
V
–10
0.6
V
10
μA
3
pF
CNV+, Single-Ended Convert Start Mode (CNV– Tied to GND)
VIH
High Level Input Voltage
VDDL = 2.5V
l
VIL
Low Level Input Voltage
VDDL = 2.5V
l
CIN
Digital Input Capacitance
1.7
V
0.6
V
2
pF
CNV+/CNV–, Differential Convert Start Mode
VID
Differential Input Voltage
VICM
Common Mode Input Voltage
(Note 13)
l
175
350
650
mV
l
0.8
1.25
1.7
V
l
175
350
650
mV
l
0.8
1.25
1.7
V
mV
CLK+/CLK– (LVDS Clock Input)
VID
Differential Input Voltage
VICM
Common Mode Input Voltage
(Note 13)
DCO+/DCO–, DA+/DA–, DB+/DB– (LVDS Outputs)
VOD
Differential Output Voltage
100Ω Differential Load
l
247
350
454
VOS
Common Mode Output Voltage
100Ω Differential Load
l
1.125
1.25
1.375
V
Power Requirements
The l denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VDD
Supply Voltage
(Note 6)
l
4.75
5
5.25
V
VDDL
Supply Voltage
(Note 6)
l
2.375
2.5
2.625
V
OVDD
Supply Voltage
(Note 6)
l
2.375
2.5
2.625
V
IVDD
IVDDL
IOVDD
IPOWERDOWN
IPOWERDOWN
Supply Current
Supply Current
Supply Current
Power-Down Mode Current
Power-Down Mode Current
10Msps Sample Rate
10Msps Sample Rate
10Msps Sample Rate
Power-Down Mode (IVDD)
Power-Down Mode (IVDDL + IOVDD)
l
l
l
l
l
4
22.5
8.3
1
2
4.8
25.6
10
20
250
mA
mA
mA
μA
μA
PD
Power Dissipation
Power-Down Mode
10Msps Sample Rate
Power-Down Mode (IVDD + IVDDL + IOVDD)
l
l
97
10
113
725
mW
μW
IDIFFCNV
Increase in IVDDL with Differential CNV Mode Enabled (No Increase During Power-Down)
2.1
ITWOLANE
Increase in IOVDD with Two-Lane Mode Enabled (No Increase During Power-Down)
3.6
mA
mA
238616f
4
For more information www.linear.com/LTC2386-16
LTC2386-16
ADC Timing Characteristics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
fSMPL
Sampling Frequency
l
0.02
tCONV
CNV ↑ to Output Data Ready
l
67
tACQ
Acquisition Time
tCYC
Time Between Conversions
TYP
72
MAX
UNITS
10
Msps
78
tCYC – 50
l
100
ns
ns
50,000
ns
tCNVH
CNV High Time
(Note 13)
l
5
ns
tCNVL
CNV Low Time
(Note 13)
l
8
ns
80
tFIRSTCLK
CNV ↑ to First CLK ↑ from the Same Conversion
(Note 13)
l
tLASTCLK
CNV ↑ to Last CLK ↓ from the Previous
Conversion
(Note 13)
l
tCLKH
CLK High Time
l
1.25
ns
tCLKL
CLK Low Time
l
1.25
ns
tCLKDCO
CLK to DCO Delay
(Note 13)
l
0.7
1.3
2.3
ns
tCLKD
CLK to DA/DB Delay
(Note 13)
l
0.7
1.3
2.3
ns
tSKEW
DCO to DA/DB skew
tCLKD – tCLKDCO (Note 13)
l
–200
0
200
ps
tAP
Sampling Delay Time
(Note 13)
0
tJITTER
Sampling Delay Jitter
(Note 13)
0.25
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to ground.
Note 3: When these pin voltages are taken below ground or above VDD,
VDDL or OVDD, they will be clamped by internal diodes. This product can
handle input currents up to 100mA below ground or above VDD, VDDL or
OVDD without latchup.
Note 4: When this pin voltage is taken below ground, it will be clamped by
an internal diode. When this pin voltage is taken above VDDL, it is clamped
by a diode in series with a 2k resistor. This product can handle input
currents up to 100mA below ground without latchup.
Note 5: VDD = 5V, VDDL = 2.5V, OVDD = 2.5V, fSMPL = 10MHz,
REFIN = 2.048V, single-ended CNV, one-lane output mode unless
otherwise noted.
Note 6: Recommended operating conditions.
ns
62
ns
ns
psRMS
Note 7: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
Note 8: Zero-scale error is the offset voltage measured from –0.5LSB
when the output code flickers between 0000 0000 0000 0000 and
1111 1111 1111 1111. Full-scale error is the worst-case deviation of
the first and last code transitions from ideal and includes the effect of
offset error.
Note 9: When REFBUF is overdriven, the internal reference buffer must be
turned off by setting REFIN = 0V.
Note 10: All specifications in dB are referred to a full-scale ±VREFBUF
differential input.
Note 11: Temperature coefficient is calculated by dividing the maximum
change in output voltage by the specified temperature range.
Note 12: fSMPL = 10MHz, IREFBUF varies linearly with sample rate.
Note 13: Guaranteed by design, not subject to test.
238616
For more information www.linear.com/LTC2386-16
5
LTC2386-16
Typical
Performance Characteristics
TA = 25°C, VDD = 5V, VDDL = 2.5V, OVDD = 2.5V,
REFIN = 2.048V, fSMPL = 10Msps, unless otherwise noted.
0.5
6.0
0.4
4.5
0.3
0.5
0.4
0.3
3.0
0.1
0
–0.1
–0.2
1.5
0
–1.5
0.1
0
–0.1
–0.2
–3.0
–0.3
–0.4
–4.5
–0.5
–6.0
0
16384
32768
49152
OUTPUT CODE
65536
–0.3
–0.4
0
16384
32768
49152
OUTPUT CODE
DC Histogram
DC Histogram
225000
0
σ = 0.35
200000
175000
75000
0
–40
–60
–80
–100
–80
–100
–120
–120
25000
–140
–140
N–2
N–1
N
N+1
OUTPUT CODE
N+2
–160
N+3
0
1
238616 G03
2
3
FREQUENCY (MHz)
65536
–60
50000
0
N–3
32768
49152
OUTPUT CODE
4
SNR = 94.0dB
THD = –109dB
SINAD = 93.8dB
SFDR = 109dB
–20
AMPLITUDE (dBFS)
AMPLITUDE (dBFS)
100000
16384
32k Point FFT fSMPL = 10Msps,
fIN = 200kHz
SNR = 94.0dB
THD = –117dB
SINAD = 93.9dB
SFDR = 119dB
–40
125000
0
238616 G02
32k Point FFT fSMPL = 10Msps,
fIN = 2kHz
–20
150000
–0.5
65536
238616 G01b
238616 G01a
COUNT
0.2
DNL ERROR (LSB)
0.2
INL ERROR (ppm)
INL ERROR (LSB)
Differential Nonlinearity vs
Output
OutputCode
Code
Integral Nonlinearity
vs Output Code (ppm)
Integral Nonlinearity vs
Output Code (LSB)
5
–160
0
1
2
3
FREQUENCY (MHz)
4
238616 G04
SNR = 93.8dB
THD = –101dB
SINAD = 93.2dB
SFDR = 102dB
–20
–80
–100
–100
–140
–140
–160
–160
2
3
FREQUENCY (MHz)
4
5
238616 G06
92
–80
–120
SNR
94
–60
–120
1
SNR,
Input Frequency
Frequency
SNR, SINAD vs Input
96
SNR = 93.1dB
THD = –83dB
SINAD = 82.6dB
SFDR = 84dB
–40
–60
0
32k Point FFT fSMPL = 10Msps,
fIN
IN = 5MHz
–20
AMPLITUDE (dBFS)
–40
AMPLITUDE (dBFS)
0
238616 G05
SNR, SINAD (dBFS)
0
32k Point FFT fSMPL = 10Msps,
fIN = 1MHz
5
SINAD
90
88
86
84
82
80
0
1
2
3
FREQUENCY (MHz)
4
5
238616 G07
78
0.01
0.1
1
FREQUENCY (MHz)
10
238616 G08
238616f
6
For more information www.linear.com/LTC2386-16
LTC2386-16
Typical
Performance Characteristics
REFIN = 2.048V, fSMPL = 10Msps, unless otherwise noted.
THD vs Input Frequency
and Amplitude
150
–70
–1dBFS
–3dBFS
–6dBFS
–10dBFS
150
dBFS
130
–100
–110
–120
120
110
dBc
100
120
90
80
110
100
0.1
1
FREQUENCY (MHz)
80
70
60
50
–70
10
dBc
90
60
–140
0.01
dBFS
130
70
–130
fSFDR
vs Input Level, fIN = 1MHz
IN = 1MHz
140
140
SFDR (dBFS, dBc)
THD (dBFS)
–90
SFDR
vs Input Level, fIN = 2kHz
IN
SFDR (dBFS, dBc)
–80
TA = 25°C, VDD = 5V, VDDL = 2.5V, OVDD = 2.5V,
–60
–50 –40 –30 –20
INPUT LEVEL (dBFS)
238616 G09
–10
50
–70
0
–60
–50 –40 –30 –20
INPUT LEVEL (dBFS)
–10
238616 G10
SNR, SINAD vs Temperature,
–105
SNR
SINAD
93
92
0.4
THD
2ND
3RD
MAX INL
MAX DNL
MIN DNL
MIN INL
0.3
–110
THD, HARMONICS (dBFS)
SNR, SINAD (dBFS)
94
INL/DNL vs Temperature
Temperature
2kHz, –1dBFS
–1dBFS
ffIN
IN == 2kHz,
INL/DNL ERROR (LSB)
95
THD, Harmonics vs Temperature,
fIN = 2kHz, -1dBFS
–1dBFS
–115
–120
0
238616 G11
0.2
0.1
0
–0.1
–0.2
–0.3
91
–40
–20
0
20
40
TEMPERATURE (°C)
60
–125
–40
80
–20
238616 G12
60
80
–0.4
–40
Full-Scale Error vs Temperature,
Zero-ScaleError
Errorvs
vsTemperature
Temperature
Zero-Scale
1.0
25
0
–0.5
– FS
–1.0
–1.5
–40
SUPPLY CURRENT (mA)
1.0
ZERO-SCALE ERROR (LSB)
30
0.5
0
–0.5
–1.0
–20
0
20
40
TEMPERATURE (°C)
60
80
238616 G15
–1.5
–40
60
80
Supply Current vs Temperature
1.5
+ FS
0
20
40
TEMPERATURE (°C)
238616 G14
1.5
0.5
–20
238616 G13
REFBUF == 4.096V
4.096V
REFBUF
FULL–SCALE ERROR (LSB)
0
20
40
TEMPERATURE (°C)
20
IVDDL
IVDD
IOVDD
15
10
5
–20
0
20
40
TEMPERATURE (°C)
60
80
238616 G16
0
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
238616 G17
238616
For more information www.linear.com/LTC2386-16
7
LTC2386-16
Typical
Performance Characteristics
REFIN = 2.048V, fSMPL = 10Msps, unless otherwise noted.
Analog Input Current
vs
Differential
Input
Voltage
Differential
Input
Voltage
Supply Current vs Sample Rate
30
0.75
IVDDL
IVDD
IOVDD
15
10
5
0
0
2.5
5
7.5
SAMPLE RATE (MHz)
10
0.50
Internal Reference Output
vs Temperature
0.25
0
–0.25
–0.50
IN
–0.75
–4.096
2.050
fSMPL = 10Msps
IN–
REFERENCE OUTPUT (V)
ANALOG INPUT CURRENT (mA)
SUPPLY CURRENT (mA)
25
20
TA = 25°C, VDD = 5V, VDDL = 2.5V, OVDD = 2.5V,
+
–2.048
0
2.048
DIFFERENTIAL INPUT (V)
238616 G18
4.096
238616 G19
THREE TYPICAL UNITS
2.049
2.048
2.047
–40
–20
0
20
40
TEMPERATURE (°C)
60
80
238616 G20
Pin Functions
GND (Pins 1, 4, 10, 21, 26, 29 ): Ground. Connect to a
solid ground plane in the PCB underneath the ADC.
IN+, IN– (Pins 2, 3): Positive and Negative Differential
Analog Inputs. The inputs must be driven differentially
and 180° out of phase, with a common mode voltage of
2.048V. The differential input range is ±4.096V (each input
pin swings from 0V to 4.096V.)
REFGND (Pins 5, 6): Reference Ground. The two pins
should be shorted together and connected to the reference bypass capacitor with a short, wide trace. In addition, connect the pins to the exposed pad (Pin 33). A
suggested layout is shown in the ADC Reference section
of the data sheet.
REFBUF (Pins 7, 8): Internal Reference Buffer Output.
The output voltage of the internal 2× gain reference buffer,
nominally 4.096V, is provided on this pin. The two pins
should be shorted together and bypassed to REFGND with
a 10µF (X7R, 0805 size) ceramic capacitor. If the internal
buffer is not required, tie REFIN to GND to power down
the buffer and connect an external 4.096V reference to
REFBUF.
REFIN (Pin 9): Internal Reference Output/Reference Buffer
Input. The output voltage of the internal reference, nominally 2.048V, is output on this pin. An external reference
can be applied to REFIN if a more accurate reference is
required. For increased filtering of reference noise, bypass
this pin to GND using a 0.1µF or larger ceramic capacitor.
If the internal reference buffer is not used, tie REFIN to
GND to power down the buffer and connect an external
buffered reference to REFBUF.
VDD (Pins 11, 12): 5V Analog Power Supply. The range
of VDD is 4.75V to 5.25V. The two pins should be shorted
together and bypassed to GND with 0.1μF and 10μF ceramic capacitors.
PD (Pin 13): Digital input that enables power-down mode.
When PD is low, the LTC2386 enters power-down mode,
and all circuitry (including the LVDS interface) is shut
down. When PD is high, the part operates normally. Logic
levels are determined by OVDD.
TESTPAT (Pin 14): Digital input that forces the LVDS data
outputs to be a test pattern. When TESTPAT is high, the
digital outputs are a test pattern. When TESTPAT is low,
the digital outputs are the ADC conversion result. Logic
levels are determined by OVDD.
DB–/DB+, DA–/DA+ (Pins 15/16, 17/18): Serial LVDS
Data Outputs. In one-lane output mode, DB–/DB+ are not
used and their LVDS driver is disabled to reduce power
consumption.
238616f
8
For more information www.linear.com/LTC2386-16
LTC2386-16
Pin Functions
DCO–/DCO+ (Pins 19/20): LVDS Data Clock Output. This
is an echoed version of CLK–/CLK+ that can be used to
latch the data outputs.
into the hold mode and starts a conversion cycle. CNV+
can also be driven with a 2.5V CMOS signal if CNV– is
tied to GND.
OVDD (Pin 22): 2.5V Output Power Supply. The range of
OVDD is 2.375V to 2.625V. Bypass to GND with a 0.1μF
ceramic capacitor.
VDDL (Pins 30, 31): 2.5V Analog Power Supply. The
range of VDDL is 2.375V to 2.625V. The two pins should
be shorted together and bypassed to GND with 0.1μF and
10μF ceramic capacitors.
CLK–/CLK+ (Pins 23/24): LVDS Clock Input. This is an
externally applied clock that serially shifts out the conversion result.
TWOLANES (Pin 25): Digital input that enables two-lane
output mode. When TWOLANES is high (two-lane output
mode), the ADC outputs two bits at a time on DA–/DA+
and DB–/DB+. When TWOLANES is low (one-lane output
mode), the ADC outputs one bit at a time on DA–/DA+, and
DB–/DB+ are disabled. Logic levels are determined by VDDL.
CNV–/CNV+ (Pins 27/28): Conversion Start LVDS Input.
A rising edge on CNV+ puts the internal sample-and-hold
VCM (Pin 32): Common Mode Output. VCM, nominally
2.048V, can be used to set the common mode of the analog inputs. Bypass to GND with a 0.1μF ceramic capacitor
close to the pin. If VCM is not used, the bypass capacitor
is not necessary as long as the parasitic capacitance on
the VCM pin is under 10pF.
Exposed Pad (Pin 33): The exposed pad on the bottom
of the package. Connect to the ground plane of the PCB
using multiple vias.
Functional Block Diagram
VDD
VDDL
OVDD
CNV
CONTROL
LOGIC
TWOLANES
TESTPAT
PD
CLK
IN+
+
VCM
SERIAL
LVDS
INTERFACE
16-BIT, 10Msps ADC
IN–
–
0.5
2
GND
REFGND
REFBUF
15k
DCO
DA
DB
2.048V
REFERENCE
REFIN
238616 BD
238616
For more information www.linear.com/LTC2386-16
9
10
For more information www.linear.com/LTC2386-16
DA–
DA+
DCO–
DCO+
CLK–
CLK+
CNV+
CNV–
LOGIC 0
tFIRSTCLK
tCONV
D6 D5 D4 D3 D2 D1 D0
tCNVH
tAP
OUTPUT DATA FROM SAMPLE N–1
ANALOG
INPUT
SAMPLE N
D15
tCYC
1
3
4
5
6
tLASTCLK
7
8
OUTPUT DATA FROM SAMPLE N
14 13 12 11 10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
2
INPUT ACQUISITION
tACQ
SAMPLE N+1
One-Lane Output Mode
LOGIC 0
D15
OUTPUT DATA FROM SAMPLE N+1
238616 TD01
14 13 12 11 10 D9 D8 D7 D6 D5
INPUT ACQUISITION
LTC2386-16
Timing Diagram
238616f
For more information www.linear.com/LTC2386-16
12 10 D8 D6 D4 D2 D0
LOGIC 0
LOGIC 0
tFIRSTCLK
tCONV
13 11 D9 D7 D5 D3 D1
tCNVH
tAP
OUTPUT DATA FROM SAMPLE N–1
DB–
DB+
DA–
DA+
DCO–
DCO+
CLK–
CLK+
CNV+
CNV–
ANALOG
INPUT
SAMPLE N
tCYC
1
3
tLASTCLK
4
12 10 D8 D6 D4 D2 D0
13 11 D9 D7 D5 D3 D1
2
OUTPUT DATA FROM SAMPLE N
D14
D15
INPUT ACQUISITION
tACQ
SAMPLE N+1
Two-Lane Output Mode
LOGIC 0
LOGIC 0
238616 TD02
12 10 D8 D6
13 11 D9 D7
OUTPUT DATA FROM SAMPLE N+1
D14
D15
INPUT ACQUISITION
LTC2386-16
Timing Diagram
238616
11
LTC2386-16
Timing Diagram
Data Output Timing
tCLKH
CLK–
tCLKL
CLK+
DCO–
tCLKDCO
tCLKDCO
tCLKD
tCLKD
DCO+
DA–
DA+
DB–
DB+
238616 TD03
Applications Information
Overview
Converter Operation
The LTC2386-16 is a low noise, high speed, 16-bit successive approximation register (SAR) ADC. Operating from 5V
and 2.5V supplies, the LTC2386-16 has a fully differential
±4.096V input range, making it ideal for applications that
require a wide dynamic range. The LTC2386-16 achieves
±0.5LSB INL (maximum), no missing codes at 16-bits
and 94dB SNR (typical).
The LTC2386-16 operates in two phases. During the acquisition phase, the sample capacitors are connected to
the analog input pins IN+ and IN– to sample the differential
analog input voltage. A rising edge on the CNV pin initiates
a conversion. During the conversion phase, the ADC is
sequenced through a successive approximation algorithm,
comparing the sampled input with binary-weighted fractions of the reference voltage (e.g. VREFBUF/2, VREFBUF/4
… VREFBUF/65536) using a differential comparator. At the
end of conversion, control logic prepares the 16-bit digital
output code for serial transfer.
The LTC2386-16 includes a precision internal 2.048V
reference, with a guaranteed 0.25% initial accuracy and
a ±20ppm/°C (maximum) temperature coefficient, as well
as an internal reference buffer. The LTC2386-16 also has
a high speed serial LVDS interface that can output one or
two bits at a time. The fast 10Msps throughput with no
pipeline latency makes the LTC2386-16 ideally suited for
a wide variety of high speed applications. The LTC2386-16
dissipates only 97mW at 10Msps and has a power-down
mode to reduce the power consumption to 10μW during
inactive periods.
Transfer Function
The LTC2386-16 digitizes the full-scale voltage of 2×
REFBUF into 216 levels, resulting in an LSB size of 125μV
with REFBUF = 4.096V. The output data is in two’s complement format. The ideal transfer function is shown in Figure
1. The ideal offset binary transfer function can be obtained
from the two’s complement transfer function by inverting
the most significant bit (MSB) of each output code.
238616f
12
For more information www.linear.com/LTC2386-16
LTC2386-16
OUTPUT CODE (TWO’S COMPLEMENT)
Applications Information
The inputs draw a small current spike while charging the
CSAMPLE capacitors during acquisition. This current spike is
consistent and does not depend on the previously sampled
input voltage. During conversion and power-down, the
analog inputs draw only a small leakage current.
011...111
BIPOLAR
ZERO
011...110
000...001
000...000
111...111
Input Drive Circuits
111...110
100...001
A low impedance source can directly drive the high impedance inputs of the LTC2386-16 without gain error. A
high impedance source should be buffered to minimize
settling time during acquisition and to optimize the distortion performance of the ADC. Minimizing settling time
is important even for DC signals because the ADC inputs
draw a current spike when entering acquisition.
FSR = +FS – –FS
1LSB = FSR/65536
100...000
–FSR/2
–1 0V 1
FSR/2 – 1LSB
LSB
LSB
INPUT VOLTAGE (V)
238616 F01
Figure 1. LTC2386-16 Transfer Function
Analog Inputs
The LTC2386-16 has a fully differential ±4.096V input
range. The IN+ and IN– pins should be driven 180 degrees
out-of-phase with respect to each other, centered around
a common mode voltage (IN+ + IN–)/2 that is restricted
to (VREFBUF/2 ± 0.1V). The ADC samples and digitizes the
voltage difference between the two analog input pins (IN+
− IN–), and any unwanted signal that is common to both
inputs is reduced by the common mode rejection ratio
(CMRR) of the ADC. The analog inputs can be modeled
by the equivalent circuit shown in Figure 2. The diodes
and 10Ω resistors at the input provide ESD and overdrive
protection. In the acquisition phase, each input sees approximately 18pF (CSAMPLE) from the sampling capacitor
in series with 28Ω (RON) from the on-resistance of the
sampling switch. CPAR is a lumped capacitance on the
order of 2pF formed primarily of diode junctions.
VDD
IN+
10Ω
28Ω
CSAMPLE
18pF
CPAR
2pF
BIAS
VOLTAGE
VDD
IN–
10Ω
28Ω
CSAMPLE
18pF
CPAR
2pF
238616 F02
Figure 2. Equivalent Circuit for the Differential Analog
Inputs of the LTC2386-16
For best performance, a buffer amplifier should be used
to drive the analog inputs of the LTC2386-16. The amplifier provides low output impedance enabling fast settling
of the analog signal during the acquisition phase. It also
provides isolation between the signal source and the current
spike drawn by the ADC inputs when entering acquisition.
The LTC2386-16 is optimized for pulsed inputs that are
fully settled when sampled, or dynamic signals up to
7.5MHz. Input signals that change faster than 300mV/
ns when they are sampled are not recommended. This is
equivalent to an 8VP-P sine wave at 12MHz.
Input Filtering
The noise and distortion of the buffer amplifier and other
supporting circuitry must be considered since they add
to the ADC noise and distortion. A buffer amplifier with
low noise density must be selected to minimize SNR
degradation. A filter network should be placed between
the buffer output and ADC input to both minimize the
noise contribution of the buffer and reduce disturbances
reflected into the buffer from ADC sampling transients. A
simple one-pole lowpass RC filter is sufficient for many
applications. It is important that the RC time constant of
this filter be small enough to allow the analog inputs to
settle within the ADC acquisition time (tACQ), as insufficient
settling can limit INL and THD performance.
High quality capacitors and resistors should be used in
the RC filters since these components can add distortion.
NPO type dielectric capacitors have excellent linearity.
238616
For more information www.linear.com/LTC2386-16
13
LTC2386-16
Applications Information
Carbon surface mount resistors can generate distortion
from self-heating and from damage that may occur during
soldering. Metal film surface mount resistors are much
less susceptible to both problems.
Input Currents
Figure 3 shows a typical input drive circuit with an RC
filter. The optimal values for R and C are application specific and may require experimentation. Setting R = 24.9Ω
gives good performance over a wide range of conditions.
The analog inputs may be modeled as a switched capacitor
load on the drive circuit. A drive circuit may rely partially on
attenuating switched-capacitor current spikes with small
filter capacitors placed directly at the ADC inputs and partially on the driver amplifier having sufficient bandwidth to
recover from the residual disturbance. Amplifiers optimized
for DC performance may not have sufficient bandwidth
to fully recover at the ADC’s maximum conversion rate,
which can produce nonlinearity and other errors. Coupling
filter circuits may be classified in two broad categories:
4.096V
+
0V
24.9Ω
–
CFILT
IN+
LTC2386-16
4.096V
+
0V
24.9Ω
CFILT
IN–
–
238616 F03
Figure 3. Typical Input Drive Circuit
The value for CFILT involves a trade-off: larger values give
better noise, and smaller values give better full-scale error.
Figure 4 shows a range of capacitor values to consider as
a starting point based on the sample rate.
1000
900
800
MAX VALUE (LOWER NOISE)
CFILT (pF)
700
600
500
400
300
MIN VALUE
(LOWER FULL-SCALE ERROR)
200
100
0
5
6
7
8
9
SAMPLE RATE (Msps)
10
238616 F04
One of the biggest challenges in coupling an amplifier to
the LTC2386-16 is in dealing with current spikes drawn
by analog inputs at the start of each acquisition phase.
Fully Settled – This case is characterized by filter time
constants and an overall settling time that are considerably shorter than the sample period. When acquisition
begins, the coupling filter is disturbed. For a typical first
order RC filter, the disturbance will look like an initial step
with an exponential decay. The amplifier will have its own
response to the disturbance, which may include ringing. If
the input settles completely (to within the accuracy of the
LTC2386-16), the disturbance will not contribute any error.
Partially Settled – In this case, the beginning of acquisition
causes a disturbance of the coupling filter, which then
begins to settle out towards the nominal input voltage.
However, acquisition ends (and the conversion begins)
before the input settles to its final value. This generally
produces a gain error, but as long as the settling is linear,
no distortion is produced. The coupling filter’s response
is affected by the amplifier’s output impedance and other
parameters. A linear settling response to fast switchedcapacitor current spikes can NOT always be assumed for
precision, low bandwidth amplifiers. The coupling filter
serves to attenuate the current spikes’ high-frequency
energy before it reaches the amplifier.
Figure 4. Suggested Range of CFILT Values vs Sample Rate
238616f
14
For more information www.linear.com/LTC2386-16
LTC2386-16
Applications Information
ADC Reference
REFIN
The internal reference circuitry of the LTC2386-16 is shown
in Figure 5. There is a low noise, low drift (20ppm/°C),
bandgap reference connected to REFIN (Pin 9). An internal
reference buffer gains the REFIN voltage by 2× to 4.096V
at REFBUF (Pins 7, 8). The voltage difference between
REFBUF and REFGND determines the full-scale input range
of the ADC. The reference and reference buffer can also
be externally driven if desired.
LTC2386-16
9
8
15k
REFIN
REFBUF
2.048V
REFERENCE
2×
0.1µF
LTC2386-16
REFBUF
REFBUF
10µF
REFGND
REFGND
238616 F06
Figure 6. Configuration for Using the Internal Reference
Figure 7 shows a suggested layout for the REFBUF capacitor. The capacitor should be connected to REFBUF and
REFGND through short, wide traces. REFGND should also
be connected with a wide trace to the grounded exposed
pad (Pin 33).
7
8k
ADC
CORE
1
6
5
2
3
4
REFGND
5
238616 F05
6
Figure 5. LTC2386-16 Internal Reference Circuitry
7
8
Internal Reference with Internal Reference Buffer
To use the internal reference and internal reference buffer, bypass REFIN to GND with a 0.1μF ceramic capacitor
(Figure 6). Bypass REFBUF to REFGND with a single 10μF
(X7R, 0805 size) ceramic capacitor. The REFBUF capacitor
should be as close as possible to the LTC2386-16 package
to minimize wiring inductance. Do not place this capacitor on the opposite side of the board. Adding a second,
smaller capacitor in parallel with the 10μF may degrade
performance and is not recommended.
9 10 11 12
238616 F07
Figure 7. Suggested REFBUF Bypass Capacitor Layout
238616
For more information www.linear.com/LTC2386-16
15
LTC2386-16
Applications Information
External Reference with Internal Reference Buffer
If more accuracy and/or lower drift is desired, REFIN can
be directly overdriven by an external 2.048V reference as
shown in Figure 8. Linear Technology offers a portfolio of
high performance references designed to meet the needs
of many applications. With its small size, low power, and
high accuracy, the LTC6655-2.048 is well suited for use
with the LTC2386-16 when overdriving the internal reference. The LTC6655-2.048 offers 0.025% (max) initial
accuracy and 2ppm/°C (max) temperature coefficient for
high precision applications. Bypassing the LTC6655-2.048
with a 2.7μF to 10μF ceramic capacitor close to the REFIN
pin is recommended.
LTC6655-2.048
5V
0.1µF
VIN
VOUT_F
SHDN
VOUT_S
GND
REFIN
2.7µF
LTC2386-16
REFBUF
REFBUF
10µF
REFGND
REFGND
238616 F08
Figure 8. Using the LTC6655-2.048 as an External Reference
REFIN
LTC2386-16
LTC6655-4.096
5V
VIN
VOUT_F
SHDN
VOUT_S
0.1µF
GND
REFBUF
REFBUF
10µF
REFGND
REFGND
238616 F09
Figure 9. Overdriving REFBUF Using the LTC6655-4.096
Common Mode Output
The VCM pin is an output that provides one-half the voltage
present on the REFBUF pin. This voltage can be used to
set the common mode of a differential amplifier driving the
analog inputs. Bypass VCM to GND with a 0.1μF ceramic
capacitor. If VCM is not used it can be left floating, but the
parasitic capacitance on the pin needs to be under 10pF.
The VCM output has 1/f noise which for most driver circuits
will be removed by the ADC common mode rejection ratio.
VCM is not recommended for single-ended to differential
circuits that pass the VCM noise to only one ADC input.
Dynamic Performance
External Reference Buffer
The internal reference buffer can also be overdriven with
an external 4.096V reference at REFBUF as shown in
Figure 9. To do so, REFIN must be grounded to disable
the reference buffer. The external reference must have a
fast transient response and be able to drive the 0.5mA
to 1.2mA load at the REFBUF pin. The LTC6655-4.096 is
recommended when overdriving REFBUF.
Fast Fourier Transform (FFT) techniques are used to test
the ADC’s frequency response, distortion and noise at the
rated throughput. By applying a low distortion sine wave
and analyzing the digital output using an FFT algorithm,
the ADC’s spectral content can be examined for frequencies outside the fundamental. The LTC2386-16 provides
guaranteed tested limits for both AC distortion and noise
measurements.
238616f
16
For more information www.linear.com/LTC2386-16
LTC2386-16
Applications Information
Signal-to-Noise and Distortion Ratio (SINAD)
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC. Figure 10 shows
that the LTC2386-16 achieves a typical SNR of 94dB at a
10MHz sampling rate with a 2kHz input.
Total Harmonic Distortion (THD)
Total Harmonic Distortion (THD) is the ratio of the RMS sum
of all harmonics of the input signal to the fundamental itself.
The out-of-band harmonics alias into the frequency band
between DC and half the sampling frequency (fSMPL/2).
THD is expressed as:
THD=20log
–40
–60
–80
–100
–120
–140
–160
Signal-to-Noise Ratio (SNR)
V22 + V32 + V42 +…+ Vn 2
V1
where V1 is the RMS amplitude of the fundamental
frequency and V2 through Vn are the amplitudes of the
second through nth harmonics. Figure 10 shows that the
LTC2386-16 achieves a typical THD of –117dB at a 10MHz
sampling rate with a 2kHz input.
SNR = 94.0dB
THD = –117dB
SINAD = 93.9dB
SFDR = 119dB
–20
AMPLITUDE (dBFS)
The signal-to-noise and distortion ratio (SINAD) is the
ratio between the RMS amplitude of the fundamental input
frequency and the RMS amplitude of all other frequency
components at the A/D output. The output is band-limited
to frequencies from above DC and below half the sampling
frequency. Figure 10 shows that the LTC2386-16 achieves
a typical SINAD of 93.9dB at a 10MHz sampling rate with
a 2kHz input.
0
0
1
2
3
FREQUENCY (MHz)
4
5
238616 F10
Figure 10. 32k Point FFT of the LTC2386-16,
fSMPL = 10Msps, fIN = 2kHz
Power Considerations
The LTC2386-16 requires three power supplies: VDD (5V),
VDDL (2.5V), and OVDD (2.5V). Bypass VDD to GND with
a 0.1µF ceramic capacitor close to the pair of pins and a
10µF ceramic capacitor in parallel. Bypass VDDL to GND
with a 0.1µF ceramic capacitor close to the pair of pins
and a 10µF ceramic capacitor in parallel. OVDD can come
from the same source as VDDL but it should be isolated
by a ferrite bead and have its own 0.1μF bypass capacitor.
Power Supply Sequencing
The LTC2386-16 does not have any specific power supply
sequencing requirements. Care should be taken to adhere
to the maximum voltage relationships described in the
Absolute Maximum Ratings section. The LTC2386-16
has a power-on-reset (POR) circuit that will reset the
LTC2386-16 at initial power-up or whenever VDD or VDDL
drops well below their minimum values. Once the supply
voltage re-enters the nominal supply voltage range, the
POR will reinitialize the ADC.
238616
For more information www.linear.com/LTC2386-16
17
LTC2386-16
Applications Information
When PD is pulled low, LTC2386-16 enters power-down
mode. In this state, all internal functions, including the
reference and LVDS outputs, are turned off and subsequent
conversion requests are ignored. The power consumption
drops to a typical value of 10µW. This mode can be used
if the LTC2386-16 is inactive for a long period of time and
the user wants to minimize power dissipation.
The amount of time required to recover from power-down
mode depends on how REFBUF is configured. When using
the internal reference buffer with a 10µF bypass capacitor,
the ADC will stabilize after 20ms. If REFBUF is externally
driven, the recovery time can be significantly less.
Timing and Control
CNV Timing
The LTC2386-16 conversion is controlled by the CNV+ and
CNV– inputs. CNV+/CNV– can be driven directly with an
LVDS signal. Alternatively, CNV+ can be driven with a 0V
to 2.5V CMOS signal when CNV– is tied to GND. A rising
edge on CNV+ will sample the analog inputs and start a
conversion. The pulse width of CNV+ should meet the
tCNVH and tCNVL specifications in the timing table.
edge of CNV+ should be driven by a clean low jitter signal.
Note that the ADC is less sensitive to jitter on the falling
edge of CNV+.
In applications that are insensitive to jitter, CNV can be
driven directly from an FPGA.
Internal Conversion Clock
The LTC2386-16 has an internal clock that is trimmed
to achieve a maximum conversion time of 78ns. With a
typical acquisition time of 50ns, throughput performance
of 10Msps is guaranteed.
Digital Interface
The LTC2386-16 has a serial LVDS digital interface that
is easy to connect to an FPGA. Three LVDS pairs are required: CLK±, DCO±, and DA±. A fourth LVDS pair, DB±,
is optional (Figure 11).
LTC2386-16
CLK+
100Ω
CLK–
DCO+
100Ω
+
–
100Ω
+
–
100Ω
+
–
DCO–
After the LTC2386-16 is powered on, or exits power-down
mode, conversion data is invalid for the first two conversion cycles. Subsequent results are accurate as long as
the time between conversions meets the tCYC specification.
If the analog input signal has not completely settled when
it is sampled, the ADC noise performance will be affected
by jitter on the rising edge of CNV+. In this case the rising
FPGA
–
+
Power-Down Mode
DA+
DA–
DB+
OPTIONAL
DB–
238616 F11
Figure 11. Digital Output Interface to an FPGA
238616f
18
For more information www.linear.com/LTC2386-16
LTC2386-16
Applications Information
The LVDS signals should be routed on the PC board as
100Ω differential transmission lines and terminated at the
receiver with 100Ω resistors.
Data must be clocked out after the current conversion is
complete, and before the next conversion finishes. The valid
time window for clocking out data is shown in Figure 13.
Note that it is allowed to be still clocking out data when
the next conversion begins.
A conversion is started by the rising edge of CNV+. When
the conversion is complete, the most-significant data bit
is output on DA±. Data is then ready to be shifted out by
applying a burst of eight clock pulses to the CLK± input.
The data on DA± is updated by every edge of CLK±. An
echoed version of CLK± is output on DCO±. The edges of
DA± and DCO± are aligned, so DCO± can be used to latch
DA± in the FPGA. The timing of a single conversion is
shown in Figure 12.
Two-Lane Output Mode
At high sample rates the required LVDS interface data rate
can reach >300Mbps. Most FPGAs can support this, but
if a lower data rate is desired, the two-lane output mode
can be used. When the TWOLANES input pin is tied high,
CNV
1
2
3
4
5
6
7
8
CLK
DCO
tCONV
DA
D15
14 13 12 11 10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
MSB
LSB
238616 F12
Figure 12. Timing Diagram for a Single Conversion in One-Lane Mode
CONVERSION N
CONVERSION N+1
CNV
tFIRSTCLK
tLASTCLK
1
2
3
4
5
6
7
8
CLK
TIME WINDOW FOR CLOCKING OUT CONVERSION N
238616 F13
Figure 13. Valid Time Window for Clocking Out Data
238616
For more information www.linear.com/LTC2386-16
19
LTC2386-16
Applications Information
the optional LVDS output DB± is enabled, and data is output two bits at a time on DA± and DB±. Enabling the DB±
output increases the supply current from OVDD by about
3.6mA. In two-lane mode, four clock pulses are required
for CLK± (see Timing Diagrams).
Output Test Patterns
To allow in-circuit testing of the digital interface to the
ADC, there is a test mode that forces the ADC data outputs
to known values:
One-Lane Mode: 1010 0000 0111 1111
Two-Lane Mode: 1100 1100 0011 1111
The test pattern is enabled when the TESTPAT pin is
brought high.
Board Layout
The LTC2386-16 requires a printed circuit board with a
clean unbroken ground plane. A multilayer board with an
internal ground plane in the first layer beneath the ADC is
recommended. Layout for the printed circuit board should
ensure that digital and analog signal lines are separated as
much as possible. In particular, care should be taken not
to run any digital track alongside an analog signal track
or underneath the ADC.
High quality ceramic bypass capacitors should be used
at the VDD, VDDL, OVDD, VCM, REFIN, and REFBUF pins.
Bypass capacitors must be located as close to the pins as
possible. Size 0402 ceramic capacitors are recommended
(except for REFBUF). The traces connecting the pins and
bypass capacitors must be kept short and should be made
as wide as possible.
Of particular importance is the capacitor between REFBUF
and REFGND, which should be a 10μF (X7R, 0805 size)
ceramic capacitor. This capacitor should be on the same
side of the circuit board as the ADC, and as close to the
device as possible. Adding a second, smaller capacitor in
parallel with the 10μF may degrade performance and is
not recommended.
The analog inputs, convert start, and digital outputs should
not be routed next to each other. Ground fill and grounded
vias should be used as barriers to isolate these signals
from each other.
Exposed Package Pad
For good electrical and thermal performance, the exposed
pad on the bottom of the package must be soldered to a
large grounded pad on the PC board. This pad should be
connected to the internal ground planes by an array of vias.
Mechanical Stress Shift
The mechanical stress of mounting a part to a board can
cause subtle changes to the SNR and internal voltage
reference. The best soldering method is to use IR reflow
or convection soldering with a controlled temperature
profile. Hand soldering with a heat gun or a soldering iron
is not recommended.
238616f
20
For more information www.linear.com/LTC2386-16
LTC2386-16
Package Description
Please refer to http://www.linear.com/product/LTC2386-16#packaging for the most recent package drawings.
UH Package
32-Lead Plastic QFN (5mm × 5mm)
(Reference LTC DWG # 05-08-1693 Rev D)
0.70 ±0.05
5.50 ±0.05
4.10 ±0.05
3.50 REF
(4 SIDES)
3.45 ±0.05
3.45 ±0.05
PACKAGE OUTLINE
0.25 ±0.05
0.50 BSC
RECOMMENDED SOLDER PAD LAYOUT
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
5.00 ±0.10
(4 SIDES)
BOTTOM VIEW—EXPOSED PAD
0.75 ±0.05
R = 0.05
TYP
0.00 – 0.05
R = 0.115
TYP
PIN 1 NOTCH R = 0.30 TYP
OR 0.35 × 45° CHAMFER
31 32
0.40 ±0.10
PIN 1
TOP MARK
(NOTE 6)
1
2
3.50 REF
(4-SIDES)
3.45 ±0.10
3.45 ±0.10
(UH32) QFN 0406 REV D
0.200 REF
NOTE:
1. DRAWING PROPOSED TO BE A JEDEC PACKAGE OUTLINE
M0-220 VARIATION WHHD-(X) (TO BE APPROVED)
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
0.25 ±0.05
0.50 BSC
238616
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more
www.linear.com/LTC2386-16
tion that the interconnection
of itsinformation
circuits as described
herein will not infringe on existing patent rights.
21
LTC2386-16
Typical Application
Input Drive Circuit with Low Distortion Up to 1MHz
5V
2.5V
32k Point FFT, fSMPL = 10Msps,
fIN = 50kHz
2.5V
0
0.1µF
1/2 LT6201
4.096V
+
0V
24.9Ω
VDD
IN+
–
0.1µF
VDDL
OVDD
CLK
DCO
DA
DB
180pF
fIN < 1MHz
LTC2386-16
1/2 LT6201
4.096V
+
0V
24.9Ω
IN–
–
REFBUF REFGND
–40
LVDS
INTERFACE
TWOLANES
TESTPAT
PD
180pF
CNV
REFIN
–60
–80
–100
–120
10MHz
SAMPLE
CLOCK
–140
–160
0.1µF
10µF
0
1/2 LT6237
–
10nF
20Ω
fIN < 8kHz
4.096V
+
0V
1/2 LT6237
–
–2.5V
5.1Ω
10nF
20Ω
24.9Ω
C1
27nF
–40
180pF
IN+
LTC2386-16
C2
27nF 24.9Ω
180pF
IN–
4
5
SNR = 94.2dB
THD = –115dB
SINAD = 94.2dB
SFDR = 118dB
–20
5.1Ω
2
3
FREQUENCY (MHz)
128k Point FFT, fSMPL = 10Msps,
fIN = 8kHz (Zoomed View)
AMPLITUDE (dBFS)
0V
1
238616 TA02b
+7.5V
+
0
238616 TA02a
Low Power, Low Noise Input Drive Circuit for Signals Up to 8kHz
4.096V
SNR = 93.9dB
THD = –116dB
SINAD = 93.9dB
SFDR = 119dB
–20
AMPLITUDE (dBFS)
0.1µF
238616 TA03a
C1, C2: GRM3195C1H273JA01D OR OTHER NP0 CAPACITOR
–60
–80
–100
–120
–140
–160
0
50
100
150
FREQUENCY (kHz)
200
238616 TA03b
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LTC2378-20
20-Bit, 1Msps, Low Power SAR ADC
104dB SNR, –125dB THD, 21mW at 1Msps
LTC2387-18
18-Bit, 15Msps SAR ADC
95.7dB SNR, 102dB SFDR, ±3LSB INL (Max)
LTC2271
16-Bit, 20Msps Serial Dual ADC
84.1dB SNR, 99dB SFDR, 92mW per Channel
LTC6655
Precision Low Drift Low Noise Buffered Reference
5V/2.5V/2.048V/1.2V, 2ppm/°C, 0.25ppm Peak-to-Peak Noise, MSOP-8 Package
LTC6652
Precision Low Drift Low Noise Buffered Reference
5V/2.5V/2.048V/1.2V, 5ppm/°C, 2.1ppm Peak-to-Peak Noise, MSOP-8 Package
ADCs
References
Amplifiers
LT6200/LT6201 Single/Dual Low Noise Op-Amp
0.95nV/√Hz, Up to 1.6GHz GBW
238616f
22 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC2386-16
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC2386-16
LT 0116 • PRINTED IN USA
© LINEAR TECHNOLOGY CORPORATION 2016