8860 50 en

MEMORY HiCORDER 8860-50,8861-50
Recorders / Digital Oscilloscope
New REC&MEM Function
New Recording Logger and Oscilloscope
The HIOKI MEMORY HiCORDER 8860 Series now sports vastly enhanced functionality.
With new mouse and keyboard support, these models feature personal computer-like operability,
accelerated by new internal high-speed hardware that provides simpler, faster operation. The
Memory function monitors fast waveforms as easily as an oscilloscope while the Logger function records trend graphs in real time.
Convenience is improved by enhanced control via LAN and USB capabilities. A broad selection
of plug-in front-end modules supports a wide variety of measurement objects. Abnormal phenomena are accurately captured with 20 MS/s sampling and 16-bit resolution on isolated inputs.
Existing input modules for former 8860 models can be used as is.
2
As an Oscilloscope
As a Data Logger
Record Waveforms in Any Situation
Model 8860-50/8861-50 Series Debut!
3
Capabilities and Features
See page 4
20 MS/s high-speed sampling
Up to 32 isolated input channels (high-speed signals)
See page 5
Real-time saving to hard disk
Dual-timebase sampling for simultaneous fast and slow monitoring
Multi-channel logging on up to 128 channels (low-speed signals)
See page 6
See page 6
Enhancements from Earlier Models 8860 and 8861
l A faster CPU greatly enhances instrument operability and response.
l Three USB 2.0 ports support a USB storage device along with mouse
See page 10
and keyboard.
l New REC&MEM (Recorder and Memory) function.
Capture waveforms of high-speed transients while simultaneously
recording at slow speed. See page 5
l New LCD with wider viewing angle for easier waveform observation.
l Uses the same input modules as previous models.
l Supports the new high-voltage input module for measuring
high voltage directly. See page 4
8860-50 side view
8861-50 side view
4
Reliably capture waveform anomalies buried within normal signals
- Memory (Digital Oscilloscope) Function -
Memory Function for High-Speed Waveform Monitoring
A/D
conversion
Isolation
Input signal
Write on
memory
A/D
conversion
Display
Thermal Printer
Isolation
Input signal
Input signal
Using the same operating principle as a digital oscilloscope, data is recorded
to the expanded internal memory at high speed. Sampling rate is up to 20 MS/s
(50-ns period) for all channels simultaneously. Capture unpredictable operating
anomalies and transient waveforms.
n Records to Solid-State Memory
Because instruments that rely on disk access such as hard disk drives are
susceptible to vibration, they are often unsuitable for on-board measurements.
MEMORY HiCORDERs are preferable for on-board testing because they write
data to solid-state memory with no moving parts. You can back up data to a
PC Card or USB storage device when finished measuring. When the optional
memory backup unit is installed, the instrument’s internal memory data is
preserved when power is turned off.
Sampling period
Time
Output waveform
n All Channels Isolated, 20 MS/s Sampling
Except when using the Scanner Module, every input channel has its
own A/D converter. Because all channels are sampled simultaneously,
transient waveforms can be easily observed along with signals. The
Scanner Module switches all inputs through a single A/D converter,
but even in that case, all channels are isolated.
n Large Capacity Internal Memory
Both high-speed write capability and a large memory capacity are
provided to support high-speed sampling. Total memory capacity
ranges from 32 megawords to 1 gigaword, enabling capture of
waveform peaks by high-speed sampling, as well as long-term
recording and long-period waveform capture. (Model 8861-50 provides twice
n External Sampling Input Capability
The sampling rate for memory recording can be synchronized to an
external clock signal (up to 10 MS/s). So, for example, sampling can be
synchronized to the rotation cycle of an engine.
n Internal Memory Division (Segmentation) Function
Internal memory can be segmented for use into 4,096 blocks. By
using “sequential save” to write data to the segmented memory, the
waveform in any block can be overlaid with that in a reference block
for comparison.
the memory capacity, but with the same recording time limits.)
n An Actual Waveform
Measurement Example
For operational analysis of an inverter, the waveforms of the high
frequency switched carrier and the low frequency fundamental
both need to be observed. High-speed sampling, long-term memory
recording and input isolation make these observations possible.
Various HIOKI non-contact clamp-on sensors capable of measuring
up to HF ranges can be used to observe current waveforms.
CLAMP ON PROBE 3270 Series provides flat electrical
characteristics for observing current waveforms over a
remarkably broad range of amplitudes from mA order to
500 A at frequencies from DC to HF.
n High-Voltage
Measurement
HIGH VOLTAGE UNIT 8961
DIFFERENTIAL PROBE 9322
Three-Phase Inverter Output Circuit
(Because emitter voltage for each phase is different, isolated measurements are essential.)
Measuring in situations where high voltage exists between channels,
such as three-phase inverters, requires a measurement instrument
that has all input channels isolated. In addition, when measuring
signals such as those of switching circuits that include commonmode voltage with a high-frequency component, the isolated circuit’s
common-mode frequency rejection characteristics can greatly affect
measurements. To measure these kinds of voltages, you can use the
HIGH VOLTAGE UNIT 8961 or the optional DIFFERENTIAL PROBE
9322 for CAT III 600-volt AC and DC maximum ratede voltage to
earth.
5
Capture High-Speed Signals by Triggering During Slow Recording
- New REC&MEM Function and Real-Time Saving Simultaneous Long-Term Monitoring and Transient Recording (REC&MEM)
n Transient waveform recording that is impossible with a pen recorder
The new REC&MEM function can record high-speed waveforms such as
intermittent noise by applying a trigger while recording long-term fluctuations
just like a pen recorder. This type of measurement previously required choosing
between the Recorder function (for slow trend graph recording), or the Memory
function (for high-speed oscilloscope-style recording). Now both types of
waveforms can be recorded simultaneously using the REC&MEM function.
REC mode recording
Waveform envelopes recorded as
pairs of maximum and minimum
values
MEM mode recording
n Maximum recording time for REC&MEM function (Recorder waveform)
Waveform captured with high-speed sampling
• The setting range depends on installed memory capacity, whether Memory Division is enabled, and whether 16-Ch Scanner Unit
8958 is installed.
• Recording length "Continuous" is not available with 100 to 200 ms/div timebase setting, and with the printer enabled.
• Timebase settings from 10 ms/div to 1 s/div are not available when using A6 Printer Unit 8995-01 and numerical value printing.
• When the sampling period for Recording and Memory recording is set at the same time.
• Operation cannot be guaranteed when the time axis is longer than one year.
Without Scanner
Unit 8958
Memory capacity
32 M-words
Memory capacity
128 M-words
Memory capacity
512 M-words
Memory capacity
1 G-word
Sampling
REC
Timebase Period
2,000 div
10,000 div
40,000 div
80,000 div
to
30 min/DIV
100ns
3min 20s
16min 40s
to
to
41d 16h
to
83d 08h
1 hr/DIV
208d 08h
1h 06min 40s
2h 13min 20s
to
to
- abbreviated -
- abbreviated -
- abbreviated -
- abbreviated -
- abbreviated -
Memory capacity
32 M-words
Memory capacity
128 M-words
Memory capacity
512 M-words
Memory capacity
1 G-word
Sampling
REC
Timebase Period
500 div
2,000 div
10,000 div
20,000 div
to
30 min/DIV
50s
100ns
to
to
1 hr/DIV
3min 20s
16min 40s
33min 20s
to
to
to
10d 10h
41d 16h
20d 02h
83d 08h
208d 08h
- abbreviated -
A4 size Printer Unit
8995
Display
Thermal Printer
Write on
memory
Maximum value
Minimum value
With Scanner Unit
8958
100 ms/DIV
Input signal
Isolation
A/D
conversion
Write on
memory
A/D
conversion
A6 size Printer Unit
8995-01
Input signal
100 ms/DIV
Input signal
- omitted - abbreviated -
n Operating Principle of the Recorder Function
With the Recorder function, only maximum and minimum values
of the data sampled within the specified timebase are written to
memory, so each recorded data point consists of a pair of values,
with 100 such points recorded for each waveform timebase division.
Sampling period
Time
Because of this, the volume of recorded data is compressed while
following steep fluctuations of the measured input voltage.
Note: When data recorded with the Recorder function is viewed on a PC, both
minimum and maximum values appear as a time series of data points.
n Maximum recording time for REC&MEM function (Memory waveform)
• The setting range depends on installed memory capacity, and whether Memory Division is enabled.
Maximum recording length is available when Memory Division is disabled.
• Presence of 16-Ch Scanner Unit 8958 has no effect (scanner module signals are not written to
internal memory for Memory waveforms).
• Operation cannot be guaranteed when the time axis is longer than one year.
Memory Division is
enabled
Sampling
MEM
Timebase Period
Memory capacity
32 M-words
5,000 div
Memory capacity
128 M-words
20,000 div
Memory capacity
512 M-words
80,000 div
• Minimum recording length is available when Memory Division is set to 1,024 blocks.
Memory capacity
1 G-word
With Memory
Division 1024 blocks
Memory capacity
32 M-words
Memory capacity
128 M-words
Memory capacity
512 M-words
Memory capacity
1 G-word
160,000 div
Sampling
MEM
Timebase Period
3 div
15 div
60 div
140 div
10 μs/DIV
100ns
50ms
200ms
800ms
1.6s
10 μs/DIV
100ns
30μs
150μs
600μs
1.4ms
20 μs/DIV
200ns
100ms
400ms
1.6s
3.2s
20 μs/DIV
200ns
60μs
300μs
1.2ms
2.8ms
50 μs/DIV
500ns
250ms
1s
4s
8s
50 μs/DIV
500ns
150μs
750μs
3ms
to
5 min/DIV
to
3.0s
to
17d 08h 40min
to
69d 10h 40min
to
277d 18h 40min
to
- abbreviated -
Recording Directly to Hard Disk or Other Storage Media (Real-Time Save)
n Recording an Entire Waveform Anomaly
The Real-Time Save function writes measurement data to the specified
destination during measurement, enabling long-term measurements
independent of the instrument’s installed memory capacity. The destination
storage media may be the internal hard disk, a PC Card or a shared network
folder.
Simultaneously, overall measurement data
(the whole waveform) is recorded in the
instrument’s internal memory, which is then
saved to the storage media when measurement
is finished. For analysis, specify the range to
be analyzed from the overall waveform data,
and reload it. The reloaded data is used with the
Memory function for waveform and numerical
calculations, or with the FFT function for FFT analysis.
to
to
5 min/DIV
to
15min
3.0s
to
to
1h 15min
5h 00min
7ms
to
11h 40min
n Maximum recording time for REC&MEM function
Timebase
Sampling No. of recording channels
Period
HDD
PC card
5μs/DIV to 50μs/DIV - abbreviated - not applicable
100 μs/DIV
1μs
200 μs/DIV
500 μs/DIV
1 ms/DIV
10μs
2 ms/DIV
20μs
5 ms/DIV
50μs
10 ms/DIV
20 ms/DIV
not applicable
Max. recording time (typical)
HDD
not applicable
PC card (512 MB)
not applicable
1ch
not applicable
8h 19min 17s
2μs
1ch
not applicable
16h 38min 34s
not applicable
5μs
2ch
1ch
20h 48min 10s
20min 55s
4ch
2ch
20h 48min 10s
20min 40s
10ch
4ch
16h 38min 20s
20min 20s
24ch
8ch
17h 17min 30s
24min 20s
100μs
33ch
20ch
1day 1h 8min 20s
16min 40s
200μs
33ch
33ch
2days 2h 16min 40s
50 ms/DIV to 5 min/DIV - abbreviated - - abbreviated - - abbreviated -
- abbreviated -
not applicable
16min 40s
- abbreviated -
• Conditions: the hard disk or PC Card have just been formatted, and any recording length setting is set to
maximum. The timebase of the whole (compressed) waveform is set automatically, and the upper limit of
recording time is one year
• Recording time depends on the formatted capacity of the recording media and its available capacity, with
the above being just one example.
• Recordable time for storage media depends on the instrument's installed memory capacity, and the
total and available capacity of the media. The whole waveform is displayed in real time (and printing is
disabled).
Note: Scanner Unit 8958 is not used.
6
The Next Generation Hybrid Recorder
- A single instrument provides both oscilloscope and data logger functions Installing a Scanner Module Creates a Multi-Channel Data Logger
Recording slowly changing physical values such as temperature has been
performed by plotting recorders and hybrid recorders (combined numerical
value and analog graph recording), and is currently performed by data loggers.
On the other hand, for high-speed waveform observation, only an oscilloscope
(or MEMORY HiCORDER) can be used. However, because the demands of
measurement sites can vary, having both of these functions in a single instrument
can be advantageous.
MEMORY HiCORDER Models 8860-50 and 8861-50 and Scanner Unit 8958 are
the answer to customers’ needs.
First timebase, 50 μsec sampling
(Compressed time axis 1/200, 1 sec/div)
Second timebase, 1 sec sampling
(Same time axis with the first timebase,
1 sec/div)
n Economical Cost per Channel
The Scanner Module switches 16 input channels through one A/D converter.
Of course all channels are isolated. Cost per channel is thereby remarkably
reduced when compared to systems that include an A/D converter for every
input channel. Installing four Scanner Modules in the 8860-50 provides 64
measurement channels, and installing eight Scanner Modules in the 8861-50
provides 128 measurement channels.
First timebase, 50 μsec sampling
(Numerical display)
n Dual-Timebase Sampling at High and Low Speeds
Depending on customers’ applications, there are cases in which high-speed
signals need to be captured as waveforms while measuring multiple channels
with a Scanner Module. Both types of signals can be measured by using a
scanner module together with a common high-speed analog module, and
recording with two different timebases. Two waveforms are displayed and can
be monitored on the same time axis.
Sheet Display Function
The Sheet function has been introduced to support multi-channel
measurements (each sheet shows 32 channels). Different display
formats can be selected for each sheet, so that each sheet can be
assigned and analyzed for a particular application.
Four-split screen vertical scroll
The waveform scrolling direction can be switched between vertical
and horizontal. You can also view a continuously scrollable display to
confirm a whole long-term waveform without time-axis compression,
while simultaneously displaying time series’ and X-Y plots.
Six-split screen continuous scroll
Waveform Observation While Recording
n Changing Compression and Zooming While Measuring
Models 8860-50 and 8861-50 support changing the compression ratio, turning
the zoom function on and off, and scroll-back display while measuring, so you
can view and analyze existing measurement data without having to wait for the
measurement process to finish.
n Scroll-Back Display
An earlier portion of the waveform can be viewed without interrupt recording. This
function automatically displays earlier parts of the waveform just by turning the
Scroll knob counterclockwise. Click the Scroll Trace button on the screen, to return
the display to the current waveform position.
Timeline and XY-axis composite waveform
Turn the scroll knob to
scroll back
7
Accurately capture waveforms with diverse parameters
- Advanced trigger function -
Trigger during capturing and search after capturing
Set multiple triggers on a single channel
The trigger function allows you to set diverse parameters to detect
a particular waveform anomaly during capturing. Setting the pretrigger mode allows you to monitor the pre-trigger waveform. This is
useful for analyzing the cause of the anomaly.
On the other hand, the search function allows you to detect an anomaly after all data is captured. This allows you to search for and display
an anomaly in the same manner as with the trigger function.
When a waveform is unpredictable and setting a parameter during
measurement is difficult, it is recommended to use the search function to locate an anomaly after capturing.
Unlike with conventional MEMORY HiCORDERs, the 8860 series
allows you to set multiple trigger parameters on a particular single
channel. This allows you to set, for example, the glitch trigger, level
trigger, window-out trigger, voltage drop trigger, window-in trigger,
and on the same input waveform to monitor it. (8 parameters
in the 8860 -50 and 16 parameters in the 8861-50 can be set.)
A simple level trigger causes the
start trigger to be activated
n Stop trigger for the MEM function
Unlike with conventional MEMORY HiCORDERs, a stop trigger is supported. This
enables the timing of measurement to be controlled for both the MEM and REC
The eighth level trigger causes the
stop trigger to be activated (in the
case of specifying the event times)
functions. This also allows you to set Start or Stop independently for each trigger
source, thus enabling the timing of measurement to be controlled in a variety of
combinations. (Start or Stop trigger can also be set to the logical source.)
n Capture a sudden power loss with the drop trigger
Set the voltage drop trigger to capture a sudden power loss resulting from a blackout
caused by lighting or a circuit breaker tripping.
Set the window out trigger to capture an impulse noise or surge noise (voltage swell)
caused by, for example, the solenoid opening and closing.
n Slope trigger
Unlike with conventional MEMORY
HiCORDERs, a slope trigger is supported.
This allows you to monitor a noise
superimposed on periodic waveforms such
as a power waveform. This also allows you
to monitor a rapid change in temperature
with the amount of change in slope instead
Power waveform noise
of level.
Power waveform noise
Rapid change in temperature
For edge detection of pattern “1, 0, 0, ↑,” the
trigger is not activated in this position.
For edge detection, the trigger is not activated unless
the condition is not met after the start of measurement
n Edge detection and level detection of the logic trigger
Unlike with conventional MEMORY HiCORDERs supporting only
For level detection, the trigger is activated only if the
condition is met after the start of measurement
edge detection, the Models 8860 -50 and 8861-50 supports level
detection of the logic trigger. This function causes the trigger to be
activated when a specified pattern occurs, even if the logic pattern
condition is not met after the start of measurement.
1
0
0
↑
1
0
0
↑
In case of conventional edge detection
1
0
0
↑
In case of level detection
n Set the event times independently for each trigger source
* For the analog trigger only
Unlike with conventional MEMORY HiCORDERs,
this allows you to set the event times independently for
each trigger source, thus enabling the setting of trigger
conditions in a variety of combinations.
The trigger event times for the
trigger source is set to 5.
8
Convert the time domain to the frequency domain for analysis
- FFT analysis function -
FFT analysis function
The single-channel FFT function is used in spectrum analysis. The twochannel FFT function analyzes transfer functions. The octave analysis
function is used in acoustic analysis. The signal source for FFT analysis is
a section obtained from the waveforms captured in the MEM function (the
required number of pieces of data for FFT analysis are 1000 to 20,000 points).
The calculation speed for the same condition (when performing the most
time-consuming analysis) is about ten times faster than with the conventional
Model 8855.
n Simultaneously perform up to 16 calculations
Unlike with the conventional HIOKI 8855 and 8841 models that
allow for the simultaneous performing of up to two calculations,
the 8860 -50 and 8861-50 models allow for the simultaneous
performing of up to eight (four times more) FFT calculations
for analysis. Furthermore, the analysis channel can be selected
independently.
n Split screen (a total of 14 patterns)
You ca n sele ct a spl it sc ree n
format according to your needs.
For example, the MEM and REC
f u nct ions allow you to select
a different split screen for mat
independently for each sheet. Unlike
with, for example, the conventional
8855 and 8841 models, a function
to display superimposed graphs is
also supported (however, the function
depends on the analysis mode).
n A variety of window functions
Unlike with the conventional 8855 and 8841 models that
support only the three window function options “Rectangular,”
“Hanning,” and “Exponential,” the 8860 -50 and 8861-50
models include four additional options, thus enabling you
to select a window function from a total of seven options.
Furthermore, a difference in calculation results of line spectrum
between other companies’ FFT analyzers and HIOKI’s analyzer
can be compensated by selecting the energy attenuation
compensation method when using a window function.
n Phase Highlight Display
Phase Highlight emphasizes on the display only those parts of a
waveform that exceed a certain level, in order to acquire a power
spectrum in the midst of phase calculation. The figure shows
power and phase spectra at the same time when the highlighted
display is enabled, so you can easily see important parts of the
waveform that are normally difficult to see because they appear
like noise.
n Change the settings on the DISP screen
The dialog bar on the top of the DISP screen (waveform
monitoring screen) allows you to change the settings.
The frequency resolution and capture time are also displayed.
Time domain
Frequency domain
9
Specify an analysis point
Waveform in the MEM function
Perform FFT calculation on the waveform from the MEM function
When performing FFT analysis on the data obtained by measurement with the
MEM function, you can use the jog shuttle to specify an analysis point and view
the calculation results on the same screen. Unlike with the conventional 8855
and 8841 models, you do not need to switch between the MEM function and FFT
function screens to set the starting point of calculation. Furthermore, the display of
“Raw Data” obtained by measurement with the MEM function and the calculation
results of “Storage Waveform” on the same screen allows you to view the effect of
the window function and the spectrum waveform on the same window, thus greatly
enhancing operability for analysis.
n Rich Analysis Capabilities
Power Spectrum Density and LPC Analysis have been added
to the calculation selections, for measuring power spectrum per
Hz and spectral envelopes. As for calculation settings, former
concepts such as “Channel Modes” have been eliminated, and
channel settings are now automatically set according to the
selected calculation type, eliminating otherwise complex settings.
Power spectrum density
Yo u c a n o b t a i n a p o w e r
spectrum per Hz when
analyzing signals spread over
a wide area, such as noise.
Power spectrum density (LPC
analysis)
The most appropriate spectrum
is estimated using the statistical
method.
n Change the count of calculation points and perform re-calculation
after measurement ends
After measurement is performed using less calculation points, you
can change the point count and perform re-analysis. For example, if
you perform measurement using 1,000 calculation points, you can
then convert point count to 20,000 to perform re-analysis on the data.
In this case, the frequency resolution increases 10 times. Needless to
say, you can convert the point count to 1,000 to perform re-analysis
on the data obtained by performing measurement using 20,000
points.
* Re-calculation by changing the point count cannot be performed when Mean Frequency is set to ON.
1,000 points
n Scaling in “dB”
The long desired capability to scale in dB is supported. You
no longer need to perform logarithmic calculation holding a
calculator in one hand. The 8860-50 and 8861-50 models allow
you to enter the overall value (sum of power spectrum values)
in dB, thus making scaling easier. This
enables signals to be easily read directly
from, for example, a noise meter.
Convert 1,000 to 10,000 points
Before scaling
After scaling
10
Remote control with the Internet browser
- LAN/USB, calculation function -
n Remote control and automatic saving to a shared folder
The 8860 series allows for remote control using
the Internet browser on the computer. When you
register access to a shared folder on a computer on
the network, you can store and load data to and from
HUB
the shared folder on the 8860-50 or the 8861-50 file
screen.
n To access the shared folder:
Enter the host name of the computer on the file screen of the 8860-50, enter the user
name and password in the account field, and then select the folder you want to share.
n USB Mouse and keyboard connectivity
With the Windows-style interface, you can easily make
USB receptacle A
3 ports
settings and adjustments with the click of a mouse, and
enter text and other
comments with a
External monitor
output
Access a variety of popup
menus with a right-click
of the mouse.
keyboard as you would
PC card type II
2 slots
on a common PC.
n USB Ports and External Monitor Output
n Redundancy against errors in the storage destination
Three USB 2.0 ports are now provided to support commonly available
The 8860 series allows you to set up to two storage
destinations. Even if, for example, an overflow error occurs on a PC
card during automatic saving, switching to the second backup storage
destination takes place automatically to ensure saving continues.
PC peripherals. A VGA D-sub output connector is also included to
support viewing the measurement screen on an external monitor.
n Automatic saving during measurement
Unlike with conventional MEMORY HiCORDERs, the 8860
Automatic saving during measurement
shortens the waiting time for saving
after measurement ends
series allows automatic saving during measurement.
n Restrictions
Automatic savi ng du r ing measu rement is
restricted to 1ms/division or more of the time axis.
Also, restrictions to the time axis settings differ
depending on the scan ner module, number of
channels, storage media, and setting conditions for
real-time printing.
n Set 16 groups of numerical calculations
Unlike with conventional MEMORY HiCORDERs, the 8860
series allows you to set 16 groups of numerical calculations.
Furthermore, each group allows you to select 16 calculation items
from a total of 19. The SUB MENU screen of the waveform
screen also allows you to view and change the numerical
calculation settings and perform recalculation. This enables the
settings of calculations in each group on the waveform screen to
be changed and monitored, thus enhancing operability.
n Simultaneously display timeline and XY-axis composite waveforms
The 8860 series uses a split screen to support the simultaneous
display of “timeline waveform” and “XY-axis composite
waveform.” Any channel can be set to the X-axis and
Y-axis. The MEM function supports XY-axis waveforms.
Models 8860-50 and 8861-50 can display sixteen X-Y plots
simultaneously.
You can simultaneously display the timeline waveform
and up to two XY-axis composite waveforms.
The simultaneous display of the timeline screen
facilitates combining the X-a xis and Y-a xis
waveforms between cursor points A and B.
11
n Main unit Specifications
Basic specifications 8860-50 (max. 4 input modules)
8861-50 (max. 8 input modules)
Basic specifications 8860-50 (max. 4 input modules)
Plug-in input modules
Max. 32 analog channels (max. 128
channels with scanner unit) + 16 logic
channels (standard configuration)
Backup functions
*3 Factory installation only -
Input type/number
of channels
Plug-in input modules
Max. 16 analog channels (max. 64
channels with scanner unit) + 16 logic
channels (standard configuration)
Measurement
functions
MEM (high-speed recording)
REC (real-time recording)
REC & MEM (real-time recording + high-speed recording)
FFT (frequency analysis)
Real-time Save (records directly to storage media)
20 MS/second (50 ns, all channels simultaneously, using the ANALOG UNIT 8956)
External sampling (10 MS/second, 100 ns)
Maximum
sampling rate
1 unit: Voltage 2ch, 20 MS/s, 12-bit resolution (8956)
1 unit: Voltage 2ch, 2 MS/s, 16-bit resolution (8957)
1 unit: Voltage / Thermocouple scan 16ch, max. 50 ms refresh rate, 1/1000 of range
resolution for temperature axis - (8958)
Types of measurement 1 unit: Voltage / RMS, 1 MS/s, 12-bit resolution (8959)
signals
1 unit: Voltage / RMS, 2 MS/s, 16-bit resolution (8961)
1 unit: Voltage 2ch, 1 MS/s, 12-bit resolution (8936/8938)
Highest sampling rate and
resolution
1 unit: Voltage / Thermocouple 2ch, 4 kS/s, 12-bit resolution (8937)
(Model number of input module
1 unit: Strain gauge 2ch, 1 MS/s, 12-bit resolution (8939)
shown in parentheses)
1 unit: Strain gauge 2ch, 200 kS/s, 16-bit resolution (8960)
1 unit: Frequency / Integration / Current / Voltage 2ch, 1 MS/s, 12-bit resolution (8940)
1 unit: Accelerometer 2ch, 1 MS/s, 12-bit resolution (8947)
1 unit: Voltage 4ch, 1 MS/s, 12-bit resolution (8946)
32 Mega-words (MEMORY BOARD 9715-50 × 1) 64 Mega-words (MEMORY BOARD 9715-50 × 2)
Direct access internal (analog 12-bit + logic 4-bit) × 32 Mega-words/ch (analog 12-bit + logic 4-bit) × 32 Mega-words/ch
memory
(using 1 channel) to (analog 12-bit + logic 4-bit) (using 2 channels) to (analog 12-bit + logic 4-bit)
*1 Factory installation only: select × 2 Mega-words/ch (using 16 channels)
1 board for the 8860-50, and
2 of the same capacity for the
8861-50 when ordering.
9715-50: 32 Megawords
9715-51: 128 Megawords
9715-52: 512 Megawords
9715-53: 1 Gigaword
2 Giga-words (MEMORY BOARD 9715-53 × 2)
(analog 12-bit + logic 4-bit) × 1 Giga-word/ch
(analog 12-bit + logic 4-bit) × 1 Giga-word/ch
(using 1 channel) to (analog 12-bit + logic 4-bit) (using 2 channels) to (analog 12-bit + logic 4-bit)
× 64 Mega-words/ch (using 16 channels)
× 64 Mega-words/ch (using 32 channels)
External control
connectors
BNC connectors: external sampling input, sampling sync output
Terminal block: external trigger input, trigger output, GO/NG
output, external start, external stop, print input
Calibrator Output
Terminal Block: Select either Trigger Output, or CAL Output to
provide a 0/5 V, 1-kHz square wave for adjusting compensation
for the intrinsic capacitance of 10:1 and 100:1 probes.
GP-IB *4 : with CONTEC GP-IB CARD GP-IB (CB) FL (for unit control
and data transfer), IEEE 488.2-1987 compliant
Standard external USB: USB2.0 compliant, series A receptacle 3 ports (keyboard, mouse,
printer, HDD, USB-memory)
interfaces
*4 Using PC Card slot and LAN: RJ-45 connector, Ethernet 100BASE-TX, 10BASE-T
optional GP-IB card
Functions: HTTP server, FTP server, File sharing, DHCP compatible,
Send mail
Monitor output: 15-pin D-sub connector, SVGA output
Environmental conditions Temperature and humidity range for use: 0°C to 40°C, 20% to 80% rh
(no condensation)
Temperature and humidity range for storage: -10°C to 50°C, 20% to 90% rh
Compliance
standard
Safety: EN61010,
EMC: EN61326, EN61000-3-2, EN61000-3-3
Power
requirements
100 to 240 V AC (50/60 Hz)
12 V DC (use the DC POWER UNIT 9684 : option, factory installation only)
Power
consumption
220 VA max. (printer not used)
300 VA max. (A4 printer used)
280 VA max. (printer not used)
350 VA max. (A4 printer used)
Approx. 330 mm (12.99 in) W × 250 mm
(9.84 in) H × 184.5 mm (7.26 in) D, 8 kg
Approx. 330 mm (12.99 in) W × 250 mm
(9.84 in) H × 284.5 mm (11.20 in) D, 10.5 kg
(282.2 oz) (printer not installed)
Dimensions and
mass
Note: Internal memory is allocated depending on the number of channels used.
PC Card Type II slot (standard) × 2: up to 4GB (Flash ATA), FAT, or FAT-32
format supported
Hard disk drive (option, HD UNIT 9718-50 *2) × 1: 60GB, FAT-32 format
(370.4 oz) (printer not installed)
Approx. 330 mm (12.99 in) W × 272.5 mm Approx. 330 mm (12.99 in) W × 272.5 mm
(10.73 in) H × 184.5 mm (7.26 in) D, 9.5 kg
(10.73 in) H × 284.5 mm (11.20 in) D, 12 kg
(335.1 oz) (A4 printer installed)
(423.3 oz) (A4 printer installed)
(317.5 oz) (A6 printer installed)
(405.6 oz) (A6 printer installed)
Approx. 330 mm (12.99 in) W × 255.5 mm Approx. 330 mm (12.99 in) W × 255.5 mm
(10.06 in) H × 184.5 mm (7.26 in) D, 9.0 kg
(10.06 in) H × 284.5 mm (11.20 in) D, 11.5 kg
Note: 1 word = 2 bytes (12-bits or 16-bits), therefore 1 giga-word = 2 giga-bytes.
Data storage media
*2 Factory installation only
Clock and parameter setting backup (standard): at least 10 years; at
reference temperature (25°C)
Waveform backup function (using optional Model 9719-50 *3): 10 hours (8860-50)
or 5 hours (8861-50), after full charge, at reference temperature (25°C)
please specify upon order the
MEMORY BACKUP UNIT
9719-50
× 2 Mega-words/ch (using 32 channels)
1 Giga-word (MEMORY BOARD 9715-53 × 1)
8861-50 (max. 8 input modules)
The following items are preserved on the memory board(s) even after power off:
Supplied
accessories
Quick Start Manual × 1, Instruction Manual × 1, Input Module Guide
× 1, Analysis Supplement Manual × 1, Power cord × 1, Input cord label
× 1, Application Disk (Wave Viewer Wv, Communication Commands
table) × 1
n Maximum Recording Time for the Memory Function (single timebase)
n Maximum Recording Time for the Memory Function (dual timebase)
• One Memory Board Model 9715-50 is installed in the 8860-50, and two in the 8861-50, recording length variable,
with 32-MWords.
• Operation cannot be guaranteed when the time axis is longer than one year.
• For memory capacity, 32 MWords is standard as shown in the table below. Optional memory up to 1 GWord can be
specified when ordering.
• One Memory Board Model 9715-50 is installed in the 8860-50, and two in the 8861-50, recording length variable,
with 32-MWords.
• Operation cannot be guaranteed when the time axis is longer than one year.
• For memory capacity, 32 MWords is standard as shown in the table below. Optional memory up to 1 GWord can be
specified when ordering.
Only First
No.of
Timebase used CH
Memory
capacity
Time axis
8860-50 : 16ch
8861-50 : 32ch
8860-50 : 8ch
8861-50 : 16ch
8860-50 : 4ch
8861-50 : 8ch
8860-50 : 2ch
8861-50 : 4ch
8860-50 : 1ch
8861-50 : 2ch
First
No.of
Timebase used CH
No.of
Second
used CH
Timebase
at 8958
32MW
20,000 div
40,000 div
80,000 div
160,000 div
320,000 div
128MW
×4 (80,000 div)
×4 (160,000 div)
×4 (320,000 div)
×4 (640,000 div)
×4 (1,280,000 div)
512MW
×16 (320,000 div)
×16 (640,000 div)
×16 (1,280,000 div)
×16 (2,560,000 div)
×16 (5,120,000 div)
1GW
×32 (640,000 div)
×32 (1,280,000 div)
×32 (2,560,000 div)
×32 (5,120,000 div)
×32 (10,240,000 div)
Sampling
Period
32MW
20,000 div
32MW
40,000 div
32MW
80,000 div
32MW
160,000 div
32MW
320,000 div
5μs/DIV
50ns
100ms
200ms
400ms
800ms
1.6s
10μs/DIV
100ns
200ms
400ms
800ms
1.6s
3.2s
20μs/DIV
200ns
400ms
800ms
1.6s
3.2s
6.4s
50μs/DIV
500ns
1s
2s
4s
8s
16s
100μs/DIV
1μs
2s
4s
8s
16s
32s
200μs/DIV
2μs
4s
8s
16s
32s
1min 04s
500μs/DIV
5μs
10s
20s
40s
1min 20s
2min 40s
1ms/DIV
10μs
20s
40s
1min 20s
2min 40s
5min 20s
2ms/DIV
20μs
40s
1min 20s
2min 40s
5min 20s
10min 40s
5ms/DIV
50μs
1min 40s
3min 20s
6min 40s
13min 20s
26min 40s
10ms/DIV
100μs
3min 20s
6min 40s
13min 20s
26min 40s
53min 20s
20ms/DIV
200μs
6min 40s
13min 20s
26min 40s
53min 20s
1h 46min 40s
50ms/DIV
500μs
16min 40s
33min 20s
1h 06min 40s
2h 13min 20s
4h 26min 40s
100ms/DIV
1ms
33min 20s
1h 06min 40s
2h 13min 20s
4h 26min 40s
8h 53min 20s
200ms/DIV
2ms
1h 06min 40s
2h 13min 20s
4h 26min 40s
8h 53min 20s
17h 46min 40s
500ms/DIV
5ms
2h 46min 40s
5h 33min 20s
11h 06min 40s
22h 13min 20s
1d 20h 26min 40s
1s/DIV
10ms
5h 33min 20s
11h 06min 40s
22h 13min 20s
1d 20h 26min 40s
3d 16h 53min 20s
2s/DIV
20ms
11h 06min 40s
22h 13min 20s
1d 20h 26min 40s
3d 16h 53min 20s
7d 09h 46min 40s
5s/DIV
50ms
1d 03h 46min 40s
2d 07h 33min 20s
4d 15h 06min 40s
9d 06h 13min 20s
18d 12h 26min 40s
10s/DIV 100ms
2d 07h 33min 20s
4d 15h 06min 40s
9d 06h 13min 20s
18d 12h 26min 40s
37d 00h 53min 20s
30s/DIV 300ms
6d 22h 40min 00s
13d 21h 20min 00s
27d 18h 40min 00s
55d 13h 20min 00s
111d 02h 40min 00s
1min/DIV 600ms
13d 21h 20min 00s
27d 18h 40min 00s
55d 13h 20min 00s
111d 02h 40min 00s
222d 05h 20min 00s
100s/DIV
1.0s
23d 03h 33min 20s
46d 07h 06min 40s
92d 14h 13min 20s
185d 04h 26min 40s
370d 08h 53min 20s
2min/DIV
1.2s
27d 18h 40min 00s
55d 13h 20min 00s
111d 02h 40min 00s
222d 05h 20min 00s
5min/DIV
3.0s
69d 10h 40min 00s
138d 21h 20min 00s
277d 18h 40min 00s
- abbreviated -
- abbreviated - abbreviated -
Memory
capacity
Time axis
8860-50 : 16ch
8861-50 : 32ch
8860-50 : 8ch
8861-50 : 16ch
8860-50: 8 x 8ch 8860-50: 8 x 8ch
8861-50: 16 x 8ch 8861-50: 16 x 8ch
8860-50 : 4ch
8861-50 : 8ch
8860-50 : 2ch
8861-50 : 4ch
8860-50 : 1ch
8861-50 : 2ch
8860-50: 4 x 8ch
8861-50: 8 x 8ch
8860-50: 2 x 8ch
8861-50: 4 x 8ch
8860-50: 1 x 8ch
8861-50: 2 x 8ch
32MW
1,000 div
2,000 div
5,000 div
10,000 div
20,000 div
128MW
×5 (5,000 div)
×5 (10,000 div)
×4 (20,000 div)
×4 (40,000 div)
×4 (80,000 div)
512MW
×20 (20,000 div)
×20 (40,000 div)
×16 (80,000 div)
×16 (160,000 div)
×16 (320,000 div)
1GW
×40 (40,000 div)
×40 (80,000 div)
×32 (160,000 div)
×32 (320,000 div)
×32 (640,000 div)
Sampling
Period
32MW
1,000 div
32MW
2,000 div
32MW
5,000 div
32MW
10,000 div
32MW
20,000 div
5μs/DIV
50ns
5ms
10ms
25ms
50ms
100ms
10μs/DIV
100ns
10ms
20ms
50ms
100ms
200ms
20μs/DIV
200ns
20ms
40ms
100ms
200ms
400ms
50μs/DIV
500ns
50ms
100ms
250ms
500ms
1s
100μs/DIV
1μs
100ms
200ms
500ms
1s
2s
200μs/DIV
2μs
200ms
400ms
1s
2s
4s
500μs/DIV
5μs
500ms
1s
2.5s
5s
10s
1ms/DIV
10μs
1s
2s
5s
10s
20s
2ms/DIV
20μs
2s
4s
10s
20s
40s
5ms/DIV
50μs
5s
10s
25s
50s
1min 40s
10ms/DIV
100μs
10s
20s
50s
1min 40s
3min 20s
20ms/DIV
200μs
20s
40s
1min 40s
3min 20s
6min 40s
50ms/DIV
500μs
50s
1min 40s
4min 10s
8min 20s
16min 40s
100ms/DIV
1ms
1min 40s
3min 20s
8min 20s
16min 40s
33min 20s
200ms/DIV
2ms
3min 20s
6min 40s
16min 40s
33min 20s
1h 06min 40s
2h 46min 40s
500ms/DIV
5ms
8min 20s
16min 40s
41min 40s
1h 23min 20s
1s/DIV
10ms
16min 40s
33min 20s
1h 23min 20s
2h 46min 40s
5h 33min 20s
2s/DIV
20ms
33min 20s
1h 6min 40s
2h 46min 40s
5h 33min 20s
11h 06min 40s
5s/DIV
1d 03h 46min 40s
50ms
1h 23min 20s
2h 46min 40s
6h 56min 40s
13h 53min 20s
10s/DIV 100ms
2h 46min 40s
5h 33min 00s
13h 53min 20s
1d 03h 46min 40s
2d 07h 33min 20s
30s/DIV 300ms
8h 20min 00s
16h 40min 00s
1d 17h 40min 00s
3d 11h 20min 00s
6d 22h 40min 00s
16h 40min 00s
33h 20min 00s
3d 11h 20min 00s
6d 22h 40min 00s
13d 21h 20min 00s
100s/DIV
1.0s
1d 03h 46min 40s
2d 07h 33min 20s
5d 18h 53min 20s
11d 13h 46min 40s
23d 03h 33min 20s
2min/DIV
1.2s
1d 09h 20min 00s
2d 18h 40min 00s
6d 22h 40min 00s
13d 21h 20min 00s
27d 18h 40min 00s
5min/DIV
3.0s
3d 11h 20min 00s
6d 22h 40min 00s
17d 08h 40min 00s
34d 17h 20min 00s
69d 10h 40min 00s
1min/DIV 600ms
12
n Main unit Specifications
Recorder functions
Print/display section *6 Printer functions are available when optional printer unit is installed
Display
*6 Recording paper
*6 Recording width
*6 Paper feed density
10.4 inch TFT color LCD (SVGA, 800 × 600 dots)
RECORDING PAPER 9231: 216 mm (8.50 in) × 30 m (98.43 ft),
thermal paper roll (when using A4-size the printer unit 8995)
RECORDING PAPER 9234: 112 mm (4.41 in) × 18 m (59.06 ft),
thermal paper roll (when using A6-size the printer unit 8995-01)
RECORDING PAPER 9231: 200 mm (7.87 in) , full scale 20 divisions, 1
division = 10 mm (0.39 in) (when using A4-size the printer unit 8995)
RECORDING PAPER 9234: 100 mm (3.94 in) , full scale 10 divisions, 1
division = 10 mm (0.39 in) (when using A6-size the printer unit 8995-01)
Time axis
Virtual record function: At 10 ms - 200 ms/division, printing in real time is not possible, but
*8: waveform
data are stored in memory and can be monitored on screen. Data are stored for 5,000
divisions before the end of measurement. At recording length settings other than "Continuous", the
printer can be used simultaneously, for follow-up printing of waveforms.
Sampling rate
10 lines/mm (when using A4-size the printer unit 8995 ), 8 lines/mm
(when using A6-size the printer unit 8995-01)
* 20 lines/mm with "smoothed printing" memory function (when using A4-size the printer unit 8995)
*6 Recording speed Max. 25 mm (0.98 in)/sec
Recording length
Trigger functions
Trigger sources
Trigger types
(analog)
Turn on/off independently for each trigger source of analog/logic A – D,
external trigger (a rise of 2.5V or terminal short circuit); timer trigger,
inter-source AND/OR, forced trigger,
standard mode (trigger source to all analog channels settable), extend
mode (multiple analog sources to a single analog channel settable, up
to 8 for 8860-50, and up to 8 on channels/units 1 – 4, and up to 8 on
channels/units 5 – 8 for 8861-50 settable)
Level: Triggering occurs when preset voltage level is crossed
(upwards or downwards).
Window: Triggering occurs when window defined by upper and
lower limit is entered or exited.
Period: Rising edge or falling edge cycle of preset voltage value
is monitored and triggering occurs when defined cycle range is
exceeded.
Glitch: Triggering occurs when pulse width from rising or falling
edge of preset voltage value is underrun.
Slope: Triggering occurs when preset change degree (slope) is
exceeded or underrun.
Voltage drop: Triggering occurs when voltage drops below peak
voltage setting (for 50/60 Hz AC power lines only).
Event setting: Event count is performed for each source, and
triggering occurs when a preset count is exceeded.
Level setting resolution 0.1% of full scale (full scale = 20 divisions)
Trigger types
(logic)
Trigger filter
1, 0, 0⎥1, ×, pattern setting, AND/OR setting for groups of 4 channels,
level or edge detect selectable (0⎥1: changing to any value activates trigger)
OFF, setting range 0.1 to 10.0 divisions in 0.1 division steps (MEM, REC
(analog/logic)
& MEM function), ON (10 ms)/OFF (REC function)
Other functions
Pre-trigger function to capture pre- and post-trigger waveform,
trigger output (active Low with terminal block and open collector
5 voltage output). Level display while waiting for trigger, Start/
stop trigger conditions independently selectable
Memory functions
Time axis
5 μs to 5 min/division, 26 ranges or external sampling, time axis
resolution 100 points/division, time axis zoom: ×2 to ×10 in 3
stages, compression: 1/2 to 1/500,000 in 17 stages
Sampling rate
Fixed: 1/100 of time axis range, Variable: external sampling
Sampling period can be used to set time axis
Two different sampling rate settings are possible
Recording length
32 MW memory : free setting in 1-division steps (max. 320,000 div * ) or
built-in presets of 25 to 200,000 divisions *7
128 MW memory : free setting in 1-division steps (max. 1,280,000 div *7) or
built-in presets of 25 to 1,000,000 divisions *7
512 MW memory : free setting in 1-division steps (max. 5,120,000 div *7) or
built-in presets of 25 to 5,000,000 divisions *7
1 GW memory : free setting in 1-division steps (max. 10,240,000 div *7) or
built-in presets of 25 to 10,000,000 divisions *7
*7 Maximum recording length or built-in preset length when using 1 channel (8860-50) or 2 channels
7
(8861-50). Memory of 8861-50 is twice that of 8860-50, but recording length is the same.
10 ms to 200 ms *8/division, 500 ms to 1 hour/div with 19 ranges, time
axis resolution 100 points/division, time axis zoom: ×2 to ×4 in 2 stages,
compression: 1/2 to 1/20,000 in 13 stages
At recoding length “continuous”, time axis 20 ms/div to 1 hour/div
With scanner module 8958, time axis 50ms/div to 1 hour/div
100 ns to 1 sec in 8 stages (selectable in 1/100 of time axis range)
32 MW memory: free setting in 1-division steps (max. 5,000 div), continuous *9, up
to 1,000 divisions use with the scanner module 8958
128 MW memory: free setting in 1-division steps (max. 20,000 div), continuous *9,
up to 5,000 divisions use with the scanner module 8958
512 MW memory: free setting in 1-division steps (max. 80,000 div), continuous *9,
up to 20,000 divisions use with the scanner module 8958
1 GW memory: free setting in 1-division steps (max. 160,000 div), continuous *9,
up to 40,000 divisions use with the scanner module 8958
*9 At time axis 10 ms to 200 ms/division and printer ON, Continuous setting cannot be selected. At use
with the Printer Unit 8995-01 and numerical print ON, time axis 10 ms to 1 sec/division is disabled
Note: Memory of the 8861-50 is twice than shown above, but recording length is the same.
Waveform memory
Store data for most recent 5,000 *10 divisions, or up to 160,000 div in
memory. Backward scrolling and re-printing available.
*10 Depending on the amount of installed memory, Memory of 8861-50 or 8861 is twice
that of 8860-50 or 8860, but recording length is the same.
Split screen (1 to 8), sheet display (max. 32 channels per sheet), logging
Screen and printing (print/display measurement data as digital values), voltage axis zoom (×2 to
×100), compression (×1/2 to ×1/10), variable display
REC & MEM function
Time axis
100 ms to 1 hour/division, 16 ranges, time axis resolution 100 points/
division, sampling rate: same as sampling rate for MEM function.
Recording data of the scanner module 8958 in REC side.
Time axis
10 μs to 5 min/division, 25 ranges, time axis resolution 100 points/
division, sampling rate: 1/100 of time axis
Recording length
REC: 25 to 2,000 *11 divisions, or up to 80,000 div *11, continuous
MEM: 25 to 5,000 *11 divisions, or up to 160,000 div *11
*11 Depends on installed memory 32 MW to 1GW (free setting in 1-division steps also possible)
Waveform Memory
The last 2,500 *11 divisions, or up to 80,000 div *11 are saved to memory
for scroll-back and re-print.
Limited according to whether 16-Ch Scanner Module 8958 is installed.
Screen and
printing
Toggle REC/MEM waveform display, simultaneous display of REC/
MEM waveform with split screen, split screen (1 to 8), sheet display
(max. 32 channels per sheet), logging (print/display measurement data as
digital values), zoom (with MEM), variable display
Memory divide
Divided use of memory space (up to 1024 divisions), sequential
save, block search
(REC)
(MEM)
(REC)
FFT function
Analysis mode
Storage waveform, linear spectrum, RMS spectrum, power
spectrum, power spectrum density, cross power spectrum, power
spectrum density (LPC), auto-correlation function, histogram,
transfer function, cross-correlation function, phase spectrum,
impulse response, coherence function, octave analysis
1-channel FFT, 2-channel FFT in selected channels (up to 16 analysis
Analysis channels functions)
Frequency range
133 mHz to 8 MHz, resolution 1/400, 1/800, 1/2000, 1/4000, 1/8000
No.of sampling points 1000, 2000, 5000, 10000, 20000 points
Analysis data
Selected from: Newly loaded data / MEM function waveform
data / MEM waveform of REC & MEM function
Window functions
Rectangular, Hanning, Exponential, Hamming, Blackman,
Blackman-Harris, Flat-top
Screen and
printing
Split screen (1/2/4), Nyquist, logging (print/display measurement data as
digital values), frequency axis zoom and left/right scrolling
Averaging
Time axis / frequency axis simple averaging, exponential
averaging, peak hold, (free settting 2 times to 10,000 times)
Pre-trigger
Record data from before the trigger point, -100 to +100% of
recording length (free setting in 1% steps)
Screen and
printing
Split screen (1 to 16), X-Y screen (1, 4 screens, max. 16 combined), sheet
display (max. 32 channels per sheet), logging (print/display measurement data as
digital values), voltage axis zoom (×2 to ×100), compression (×1/2 to ×1/10),
overlay, zoom, variable display, vernier display
Real-time save function
Time axis
10 ms to 1 hour/division, 19 ranges, time axis resolution 100 points/div,
sampling speed: same as sampling rate for “Measurement Waveform”
Memory splitting
Divided use of memory space (up to 4096 divisions), sequential
save, block serch
Time axis
100 μs to 5 min/division, 22 ranges (limited depending on store target and number of
channels), time axis resolution 100 points/div, sampling rate: 1/100 of time axis
Save to
HDD, PC via LAN, PC Card (use only HIOKI’s card)
Waveform calculation
Four arithmetic operations, absolute value, exponentiation, common logarithm,
square root, moving average, differentiation once and twice, integration once and
twice, parallel displacement along the time axis, trigonometric functions (sin,
cos, tan, arc-sin, arc-cos, arc-tan), Any of 16 calculation types can be applied to
recording lengths of up to 1/4 of memory capacity
(Measurement waveform
data: sampling data)
Recording length
Depending on available space on storage media / file system / number
of channels / REC time axis, Selectable in division steps up to
maximum recording length
Screen and
printing
During measurement: Whole wave, after measurement: toggle
Whole/Measurement waveform display, simultaneous display of Whole/
Measurement waveform with split screen, split screen (1 to 8), 16 split
(A4-size printer only), sheet display (max. 32 channels per sheet), logging (print/
display measurement data as digital values), zoom, variable display
Memory transfer
Data can be analyzed in MEM function or FFT function
Waveform serch
function
Detection of trigger criteria, time, event markers and peak value
Up to 1,000 event markers can be input during and after measurement
(Numerical calculation by specifying calculation area with cursors A and B, numerical calculation judgment,
automatic saving of numerical calculation results, saving of any existing numerical calculation results)
Numerical calculation
Averaging
Average value, effective (rms) value, peak to peak value, maximum value,
time to maximum value, minimum value, time to minimum value, period,
frequency rise time, fall time, area value, X-Y area value, standard deviation,
time to level, pulse width, duty ratio, pulse count, Up to 16 items can be
selected.
Cumulative average, Exponential average (select 2 to 10,000 data objects
to be averaged)
(Whole waveform data)
13
n Main unit Specifications
Additional features
General
Measurement parameter printing, cursor measurement, scaling,
current clamp setting, comment input, screen hard copy, list/gauge,
start condition hold, auto setup, auto save, remote control (start/stop/
print control), auto range, over-range indication, VIEW function, key
lock, level monitor, vernier function, offset cancel, event marker
input, waveform search function, report printing
n Options specifications (sold separately)
DC/RMS UNIT 8959
For the 8860 series only
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 290 g (10.2 oz) Accessories: None
(Accuracy at 23 ±5°C/73 ±9°F, 30 to 80 % rh after 30 minutes of warm-up
time and zero-adjust; accuracy guaranteed for 1 year)
ANALOG UNIT 8956
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 290 g (10.2 oz) Accessories: None
(Accuracy at 23 ±5°C/73 ±9°F, 30 to 80 % rh after 30 minutes of warmup time and zero-adjust; accuracy guaranteed for 1 year)
Measurement functions
Number of channels: 2, for voltage measurementl, DC/RMS selectable
Input connectors
Isolated BNC connector (input impedance 1MΩ, input capacitance 30pF), Max. rated
voltage to earth: 370V AC, DC (with input isolated from the unit, the maximum voltage that
can be applied between input channel and chassis and between input channels without damage)
Measurement functions
Number of channels: 2, for voltage measurement
Measurement
range
Input connectors
Isolated BNC connector (input impedance 1MΩ, input capacitance 40pF), Max. rated
voltage to earth: 300V AC, DC (with input isolated from the unit, the maximum voltage that
5mV to 20V/DIV, 12 ranges, full scale: 20DIV, AC voltage for
possible measurement/display using the memory function:
280V rms, low-pass filter: 5Hz/500Hz/5kHz/100kHz
Measurement resolution
1/100 of measurement range (using 12-bit A/D conversion; installed in 8860 series)
Highest sampling rate
1MS/s (simultaneous sampling in 2 channels)
Accuracy
DC amplitude: ±0.4% of full scale (with filter 5Hz), zero position: ±0.1%
of full scale (with filter 5Hz, after zero adjustment)
RMS
measurement
RMS amplitude accuracy: ±1% of full scale (DC, 20Hz to 1kHz), ±3% of full scale (1kHz to
100kHz), response time: SLOW 5s (rise time from 0 to 90% of full scale), MID 800ms (rise time
from 0 to 90% of full scale), FAST 100ms (rise time from 0 to 90% of full scale), crest factor: 2
can be applied between input channel and chassis and between input channels without damage)
Measurement
range
5mV to 20V/DIV, 12 ranges, full scale: 20 DIV, AC voltage for possible
measurement/display using the memory function: 280V rms, low-pass
filter: 5Hz/500Hz/5kHz/1MHz
Measurement resolution
1/100 of measurement range (using 12-bit A/D conversion; installed in 8860 series)
Highest sampling rate
20MS/s (simultaneous sampling in 2 channels)
Accuracy
DC amplitude: ±0.4% of full scale (with filter 5Hz)
Zero position: ±0.1% of full scale (with filter 5Hz, after zero adjustment)
Frequency characteristics DC to 10MHz ±3dB, (with AC coupling: 7Hz to 10MHz ±3dB)
Input coupling
DC, GND, AC
Max. allowable input
400V DC (the maximum voltage that can be applied across input pins without damage)
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 310 g (10.9 oz) Accessories: None
HIGH-RESOLUTION UNIT 8957
(Accuracy at 23 ±5°C/73 ±9°F, 30 to 80 % rh after 30 minutes of warmup time and zero-adjust; accuracy guaranteed for 1 year)
Measurement functions
Number of channels: 2, for voltage measurement
Input connectors
Isolated BNC connector (input impedance 1MΩ, input capacitance 40pF), Max. rated
voltage to earth: 300V AC, DC (with input isolated from the unit, the maximum voltage that
can be applied between input channel and chassis and between input channels without damage)
Frequency characteristics DC to 400kHz ±3dB, (with AC coupling: 7Hz to 400kHz ±3dB)
Input coupling
DC, GND, AC
Max. allowable input
400V DC (the maximum voltage that can be applied across input pins without damage)
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 290 g (10.2 oz) Accessories: Conversion cable × 2, cable length 50cm (19.69in)
STRAIN UNIT 8960
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80 % rh after 1 hour of warm-up
time and auto-balance; accuracy guaranteed for 1 year)
Measurement functions Number of channels: 2, for distortion measurement (electronic auto-balancing, balance adjustment range within ±10000 με)
Input connectors
Via conversion cable, TAJIMI PRC03-12A10-7M10.5, Max. rated voltage to
earth: 33Vrms or 70V DC (with input isolated from the unit, the maximum voltage that
Suitable
transducer
Strain gauge converter, bridge impedance: 120Ω to 1kΩ (bridge voltage 2V),
350Ω to 1kΩ (bridge voltage 5V, 10V), bridge voltage 2, 5, 10 ±0.05V
can be applied between input channel and chassis and between input channels without damage)
Measurement
range
5mV to 20V/DIV, 12 ranges, full scale: 20DIV, AC voltage for
possible measurement/display using the memory function:
280V rms, low-pass filter: 5Hz/50Hz/500Hz/5kHz/50kHz
Measurement
range
20με to 1000με/DIV, 6 ranges, full scale: 20DIV, low-pass filter:
5Hz/10Hz/100Hz/1kHz
Anti-aliasing filter
Integrated filter for suppressing aliasing distortion caused by
FFT processing (automatic cutoff frequency setting/OFF)
Anti-aliasing filter
Integrated filter for suppressing aliasing distortion caused by FFT
processing (automatic cutoff frequency setting/OFF)
Measurement resolution
1/1600 of measurement range (using 16-bit A/D conversion; installed in 8860 series)
Measurement resolution 1/1600 of measurement range (using 16-bit A/D conversion; installed in 8860 series)
Highest sampling rate
2MS/s (simultaneous sampling in 2 channels)
Highest sampling rate
200kS/s (2-channel simultaneous sampling)
Accuracy
DC amplitude: ±0.2% of full scale (with filter 5Hz)
Zero position: ±0.1% of full scale (with filter 5Hz, after zero adjustment)
Accuracy After auto-balancing
DC amplitude: ±(0.4% of full scale +2με), zero position: ±(0.1% of
full scale +2με) (at 5Hz filter ON)
Frequency characteristics
DC to 200kHz ±3dB, (with AC coupling: 7Hz to 200kHz ±3dB)
Input coupling
DC, GND, AC
Max. allowable input
400V DC (the maximum voltage that can be applied across input pins without damage)
Max. allowable input
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 183 (7.20in) D mm,
approx. 385 g (13.6 oz) Accessories: Flathead screwdriver × 1, short bar × 2
16ch SCANNER UNIT 8958
Measurement functions
(Accuracy at 23 ±5°C/73 ±9°F, 30 to 80 % rh after 1 hour of warm-up
time and adjustment; accuracy guaranteed for 1 year)
Input connectors
Safety Banana Connector (input impedance 10MΩ, input capacitance 5pF), Max. rated
voltage to earth: 1000V AC, DC CAT II, 600V AC, DC CAT III (the maximum voltage
that can be applied between input channel and chassis and between input channels without damage)
Measurement
range
1V to 50V/DIV, 6 ranges, full scale: 20 DIV, AC voltage for possible
measurement/display using the memory function: 700V rms, low-pass
filter: 5Hz/50Hz/500Hz/5kHz
Measurement resolution
1/1600 of measurement range (using 16-bit A/D conversion; installed in 8860 series)
Highest sampling rate
2MS/s (simultaneous sampling in 2 channels)
Accuracy
DC amplitude: ±0.25% of full scale (with filter 5Hz)
Zero position: ±0.15% of full scale (with filter 5Hz, after zero adjustment)
RMS
measurement
RMS amplitude accuracy: ±1% of full scale (DC, 40Hz to 1kHz sin waveform),
±3% of full scale (1kHz to 10kHz sin waveform), crest factor: 2
wire: 0.14 to 1.5 mm , braided wire 0.14 to 1.0 mm (conductor wire diameter min. 0.18 mm), AWG 26 to 16
2
Input impedance: 1MΩ, 850kΩ with line fault detection ON, Max. rated
voltage to earth: 33Vrms or 70V DC (with input isolated from the unit, the
5m, 50m, 500m, 2V/DIV, 4 ranges, full scale: 20DIV, measurement range: ±100%
of full scale, digital filter: 10Hz/50Hz/60Hz, measurement resolution 1/1600 of
measurement range (using 16-bit A/D conversion; installed in 8860 series)
range of sensor)
(using 16-bit A/D conversion; installed in 8860 series)
Thermocouple
range
K: -200 to 1350°C, J: -200 to 1200°C, E: -200 to 1000°C, T: -200 to
400°C, N: -200 to 1300°C, R: 0 to 1700°C, S: 0 to 1700°C, B: 400 to
1800°C, W (WRe5-26): 0 to 2000°C, reference junction compensation:
internal/ external (switchable), line fault detection ON/OFF switchable
Accuracy
50ms/all channels (digital filter OFF), 300ms/all channels (digital
filter 50Hz/60Hz), 1.4 s/all channels (digital filter 10Hz)
Voltage: ±0.2% of full scale, thermocouple (K, J, E, T, N): ±0.05%
of full scale ±1°C, (R, S, B, W): ±0.05% of full scale ±2°C (400°C
or more), ±0.05% of full scale ±3.5°C (less than 400°C), reference
junction compensation accuracy: ±1°C (added to measurement accuracy
with internal reference junction compensation)
Max. allowable input
(Accuracy at 23 ±5°C/73 ±9°F, 30 to 80 % rh after 30 minutes of warm-up
time and zero-adjust; accuracy guaranteed for 1 year)
Number of channels: 2, for voltage measurementl, DC/RMS selectable
10°C/DIV (-100°C/ to +200°C), 50°C/DIV (-200°C/ to +1000°C), 100°C/
DIV (-200°C/ to +2000°C), 3 ranges, full scale: 20DIV, digital filter:
(Upper and lower limit values
10Hz/50Hz/60Hz, measurement resolution 1/1000 of measurement range
depend on measurement input
Data refresh rate
HIGH VOLTAGE UNIT 8961
Measurement functions
Temperature
measurement range
(JIS C 1602-1995)
(ASTM E-988-96)
Dimensions and mass: approx. 170 (6.69in) W × 19.8 (0.78in) H
× 148.5 (5.85in) D mm, approx. 310 g (10.9 oz)
Accessories: CONNECTION CORD 9242× 2, GRABBER CLIP 9243× 2
Voltage input/Thermocouple input: screw-type terminal strip, recommended
wire diameter *1, detachable terminal block (with cover) *1 Recommended cable, single-
maximum voltage that can be applied between input channel and chassis and between input
channels without damage)
Voltage
measurement
range
10V DC (the maximum voltage that can be applied across input pins without damage)
* Available from main unit 8860/8861 version 1.06
Number of channels: 16, for voltage measurement/temperature measurement with thermocouple
2
Input connectors
Frequency characteristics DC to 20kHz +1/−3dB
40V DC (the maximum voltage that can be applied across input pins without damage)
Frequency characteristics DC to 100kHz ±3dB
Input coupling
DC, GND
Max. allowable input
1000V DC (the maximum voltage that can be applied across input pins without damage)
Number of modules
Up to four units settable for the 8860 -50, or the 8861-50 one main unit.
14
n Options specifications (sold separately)
options common to Models 8861-50/8860-50/8861/8860/8842/8841/8835-01/8835/8826/8720
CONVERSION CABLE 9318 (to connect 9270 to 9272, 9277 to 9279 and 8940)
CONVERSION CABLE 9319 (to connect 3273, 3273-50 and 8940)
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 290 g (10.2 oz) Accessories: None
ANALOG UNIT 8936
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80 % rh after 30 minutes of warm-up
time and zero-adjust; accuracy guaranteed for 1 year)
Measurement functions Number of channels: 2, for voltage measurement
Input connectors
Measurement
range
Isolated BNC connector (input impedance 1MΩ, input capacitance 30pF), Max. rated
voltage to earth: 370V AC, DC (with input isolated from the unit, the maximum voltage that
can be applied between input channel and chassis and between input channels without damage)
5mV to 20V/DIV, 12 ranges, full scale: 20DIV, AC voltage for
possible measurement/display using the memory function:
280V rms, low-pass filter: 5Hz/500Hz/5kHz/100kHz
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 300 g (10.6 oz) Accessories: None
Measurement
functions
Number of channels: 2, for voltage input based frequency measurement, integration,
pulse duty ratio, current (with optional clamp-on sensor), and voltage measurement
Input connectors
Metallic BNC connector (input impedance 1MΩ, input capacitance 60pF), sensor
connector (dedicated connector for clamp-on sensor via conversion cable, common
ground with recorder), Max. rated voltage to earth: 30Vrms or 60V DC
1MS/s (simultaneous sampling in 2 channels)
Accuracy
DC amplitude: ±0.4% of full scale, zero position: ±0.1% of full scale (after zero adjustment)
Frequency characteristics DC to 400kHz ±3dB, (with AC coupling: 7Hz to 400kHz ±3dB)
Input coupling
DC, GND, AC
Max. allowable input
400V DC (the maximum voltage that can be applied across input pins without damage)
Measurement
range
Note: When using Model 8936 with serial number earlier than 041018234 on Models 8861-50/8860-50/8861/8860,
residual noise will be 850 μVp-p.
FFT ANALOG UNIT 8938
Voltage: 0.5mV to 2V/DIV, 12 ranges
Current: 5mA to 100A/DIV, 10 ranges, using current sensor (powered
Measurement functions Number of channels: 2, for voltage measurement
Integrated filter for suppressing aliasing distortion caused by FFT
processing (automatic cutoff frequency setting/OFF)
Other functions
Other specifications same as the ANALOG UNIT 8936
from the 8940, max. 4 sensors total)
Measurement
range
VOLTAGE/TEMP UNIT 8937
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80 % rh after 1 hour of warm-up
time and zero-adjust; accuracy guaranteed for 1 year)
Measurement functions Number of channels: 2, for voltage measurement/temperature measurement with thermocouple
Voltage input: metallic BNC connector (input impedance 1MΩ, input capacitance 50pF),
Input connectors thermocouple input: plug-in connector (input impedance min. 5.1MΩ), Max. rated
voltage to earth: 30Vrms or 60V DC (with input isolated from the unit, the maximum voltage
that can be applied between input channel and chassis and between input channels without damage)
Voltage measurement
range
Temperature
measurement range
500μV to 2 V/DIV, 12 ranges, full scale: 20DIV, low-pass filter:
5Hz/500Hz/5kHz/100kHz, Measurement resolution: 1/80 of
measurement range (using 12-bit A/D conversion; installed in 8860 series)
10°C to 100°C/DIV, 4 ranges, full scale: 20DIV, low-pass filter:
5Hz/500Hz, Measurement resolution:1/80 of measurement range
(using 12-bit A/D conversion; installed in 8860 series)
Thermocouple
range
K: -200 to 1350°C, E: -200 to 800°C, J: -200 to 1100°C, T: -200 to 400°C,
N: -200 to 1300°C, R: 0 to 1700°C, S: 0 to 1700°C, B: 300 to 1800°C,
Reference junction compensation: internal/ external (switchable)
Highest sampling rate
Voltage input: 1MS/s, Temperature measurement: 4kS/s (2-channel simultaneous sampling)
Accuracy
Voltage input: DC amplitude ±0.4% of full scale, zero position ±0.15% of full
scale, Temperature measurement (K, E, J, T, N): ±0.1% of full scale ±1°C,
±0.1% of full scale ±2°C (-200 to 0°C), (R, S): ±0.1% of full scale ±3°C, (B):
±0.1% of full scale ±4°C (400 to 1800°C) , Reference junction compensation
accuracy: ±0.1% of full scale ±1.5 °C (internal reference junction compensation)
Frequency
characteristics
Voltage input: DC to 400 kHz +1/−3dB
Temperature measurement: DC to 1kHz +1/−3dB
Input coupling
DC, GND, AC
Max. allowable input
30Vrms or 60V DC (the maximum voltage that can be applied across input pins without damage)
Note: When using Model 8937 with serial number earlier than 041135257 on Models 8861-50/8860-50/8861/8860,
residual noise will be 150 μVp-p.
DC amplitude accuracy: ±0.4% of full scale, zero position ±0.15%
of full scale (current measurement accuracy dependent on sensor accuracy/
characteristics)
Frequency characteristics: DC to 400kHz ±3dB
Full scale: 20DIV, Max. allowable input: 30Vrms or 60V DC (the
Note: When using Model 8938 with serial number earlier than 041132532 on Models 8861-50/8860-50/8861/8860,
residual noise will be 1.4 mVp-p.
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 300 g (10.6 oz) Accessories: None
Frequency: DC to 100kHz, with 0.05Hz to 5kHz/DIV, 11 ranges, 5 (r/
min) to 500 (r/min)/DIV, 5ranges, P50Hz (40 to 60Hz), P60Hz (50 to 70Hz)
* Power line frequency measurement requires the DIFFERENTIAL PROBE 9322 or PT 9303 ,
Accuracy: ±0.2% of full scale (except 5kHz/DIV range), ±0.7% of full
scale (5kHz/DIV range), ±0.032Hz (P50Hz, P60Hz range)
Integration: DC to 90kHz, with 5counts to 500kcounts/DIV, 11 ranges
Pulse duty ratio: 10Hz to 100kHz, with 100% of full scale, 1 range,
Accuracy: ±1% of full scale (10Hz to 10kHz)
Threshold: −10 to +10V (settable in 0.2V steps)
Full scale: 20DIV, Max. allowable input: 30Vrms or 60V DC (the
maximum voltage that can be applied across input pins without damage)
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80 % rh after 30 minutes of warm-up
time and zero-adjust; accuracy guaranteed for 1 year)
Anti-aliasing filter
(with input isolated from the unit, the maximum voltage that can be applied between
input channel and chassis and between input channels without damage)
Compatible current sensors 9270, 9271, 9272, 9277, 9278, 9279, 3273, 3273 -50
Measurement resolution 1/80 of measurement range (using 12-bit A/D conversion; installed in 8860 series)
Highest sampling rate
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80 % rh after 30 minutes of warm-up
time and zero-adjust; accuracy guaranteed for 1 year)
F/V UNIT 8940
maximum voltage that can be applied across input pins without damage)
Measurement resolution 1/80 of measurement range (installed in 8860 series, excluding current range when using 9279)
1MS/s (2-channel simultaneous sampling), (frequency/duty ratio measurement:
Highest sampling rate 1.125μs cycle)
Other functions
Voltage input pull-up: ON (10kΩ)/OFF, input coupling: DC, GND, AC
(voltage/current), DC (others), low-pass filter: 5Hz/500Hz/5kHz/100kHz
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 310 g (10.9 oz) Accessories: None
4ch ANALOG UNIT 8946
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80 % rh after 30 minutes of warm-up
time and zero-adjust; accuracy guaranteed for 1 year)
Measurement functions Number of channels: 4, for voltage measurement
Input connectors
Metallic BNC connector (input impedance 1MΩ, input capacitance 15pF), Max. rated
voltage to earth: 30Vrms or 60V DC (with input isolated from the unit, the maximum voltage
Measurement
range
10mV to 2V/DIV, 8 ranges, full scale: 20DIV, low-pass filter,
5Hz/500Hz/5kHz/50kHz, input coupling: DC, GND
that can be applied between input channel and chassis and between input channels without damage)
Measurement resolution 1/80 of measurement range (using 12-bit A/D conversion; installed in 8860 series)
Highest sampling rate
1MS/s (4-channel simultaneous sampling)
Accuracy
DC amplitude: ±0.5% of full scale, zero position: ±0.15% of full scale (after zero adjustment)
Frequency characteristics DC to 100kHz ±3dB
Max. allowable input
30Vrms or 60V DC (the maximum voltage that can be applied across input pins without damage)
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 310 g (10.9 oz) Accessories: None
CHARGE UNIT 8947
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80 % rh after 1 hour of warm-up
time and zero-adjust; accuracy guaranteed for 1 year)
Measurement functions Number of channels: 2, for acceleration measurement
Voltage input/integrated preamplifier input: metallic BNC connector
Dimensions and mass: approx. 170 (6.69in) W × 20 (0.79in) H × 148.5 (5.85in) D mm,
approx. 250 g (8.8 oz) Accessories: Conversion cable × 2
STRAIN UNIT 8939
Number of channels: 2, for distortion measurement (electronic
auto-balancing, balance adjustment range within ±10000με)
Input connectors
Via conversion cable, TAJIMI PRC03-12A10-7M10.5, Max. rated voltage to
earth: 30Vrms or 60V DC (with input isolated from the unit, the maximum voltage that
can be applied between input channel and chassis and between input channels without damage)
Suitable
transducer
Strain gauge converter, bridge impedance: 120Ω to 1kΩ, bridge
voltage 2 ±0.05V
Measurement
range
20με to 1000με/DIV, 6 ranges, full scale: 20DIV, low-pass filter:
10Hz/30Hz/300Hz/3kHz
Measurement resolution 1/80 of measurement range (using 12-bit A/D conversion; installed in 8860 series)
1MS/s (2-channel simultaneous sampling)
Accuracy After auto-balancing DC amplitude: ±(0.5% of full scale +2με), zero position: ±0.5% of full scale
Frequency characteristics DC to 20 kHz +1/−3dB
Max. allowable input
10V DC + AC peak (the maximum voltage that can be applied across input pins without damage)
Charge input: miniature connector (#10-32 UNF)
Max. rated voltage to earth: 30Vrms or 60V DC (with input isolated
from the unit, the maximum voltage that can be applied between input channel and
chassis and between input channels without damage)
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80 % rh after 1 hour of warm-up
time and auto-balance; accuracy guaranteed for 1 year)
Measurement
functions
Highest sampling rate
(for voltage input: input impedance 1MΩ, input capacitance 200pF or less)
Input connectors
Suitable
transducer
Measurement
range
Charge input
(miniature connector)
Internal pre-amp input
(BNC connector)
Measurement
range
Voltage input (BNC connector)
Charge input: Charge-output type piezoelectric acceleration pick-up sensor
Internal preamp input: Acceleration pick-up sensor with an internal preamp
50m (m/s2)/DIV to 10k (m/s2)/DIV, 12 ranges × 6 types, charge input sensitivity:
0.1 to 10 pC/(m/s2), integrated pre-amplifier input: 0.1 to 10 mV/(m/s2),
amplitude accuracy: ±2% of full scale, frequency characteristics: 1 to 50kHz,
+1/−3dB, low-pass filter: 500Hz/5kHz, pre-amplifier drive power source:
2mA ±20%, +15V ±5%, maximum input charge: ±500pC (high-sensitivity setting,
6 ranges), ±50000pC (low-sensitivity setting, 6 ranges)
500μV to 2V/DIV, 12 ranges, DC amplitude accuracy: ±0.4% of full scale, frequency
characteristics: DC to 400kHz, +1/−3 dB, low-pass filter: 5Hz/500Hz/5kHz/100kHz,
input coupling: DC, GND, AC, Max. allowable input: 30Vrms or 60V DC
Measurement resolution 1/80 to 1/32 of measurement range (depending on measurement sensitivity; installed in 8860 series)
Highest sampling rate
1MS/s (2-channel simultaneous sampling)
Integrated filter for suppressing aliasing distortion caused by
Anti-aliasing filter FFT processing (automatic cutoff frequency setting/OFF)
Note: When using Model 8947 with serial number earlier than 040933650 on Models 8861-50/8860-50/8861/8860,
residual noise will be 200 μVp-p.
15
n Options specifications (sold separately)
Perform the same functions on the computer
Cable length and mass: Main unit cable 1.5 m (4.92 ft), input section cable 30 cm
(0.98 ft), approx. 150 g (5.3 oz)
Note: The unit-side plug of the 9320-01 and 9327 is different from the 9320.
LOGIC PROBE 9320 -01/9327
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80% rh; accuracy guaranteed
for 1 year)
Function
Detection of voltage signal or relay contact signal for High/Low state recording
Input
4 channels (common ground between unit and channels), digital/contact input,
switchable (contact input can detect open-collector signals), input impedance:
1MΩ (with digital input, 0 to +5V), 500kΩ or more (with digital input, +5 to
+50V), pull-up resistance: 2kΩ (contact input: internally pulled up to +5V)
Digital input threshold 1.4V/2.5V/4.0V
1) Application software enables you to perform
the s a me data a na l ysis on a W indows
computer as on the MEMORY HiCORDERs
8860 series.
2) No confusion, because the screens
appearing on the computer are identical to
those of the 8860 series.
3) Functions identical to those of the 8860
s e r i e s, s u c h a s w ave f o r m p r o c e s s i n g
calculation, run on the computer.
MEMORY HiVIEWER 9725
Contact input
detection resistance
1.5kΩ or higher (open) and 500Ω or lower (short), 3.5kΩ or higher (open)
and 1.5kΩ or lower (short), 25kΩ or higher (open) and 8kΩ or lower (short)
Response speed
9320 -01: 500ns or lower, 9327: detectable pulse width 100ns or higher
Max. allowable input
0 to +50V DC (the maximum voltage that can be applied across input pins without damage)
Cable length and mass: Main unit cable 1.5 m (4.92 ft), input section cable 1 m (3.28 ft),
approx. 320 g (11.3 oz)
Note: The unit-side plug of the 9321-01 is different from the 9321.
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80% rh; accuracy guaranteed
for 1 year)
LOGIC PROBE 9321-01
Function
Detection of AC or DC relay drive signal for High/Low state recording
Can also be used for power line interruption detection
Input
4 channels (isolated between unit and channels), HIGH/LOW range switching
Input impedance: 100kΩ or higher (HIGH range), 30kΩ or higher (LOW range)
Output (H)
detection
170 to 250V AC, ±DC (70 to 250V ) (HIGH range)
60 to 150V AC, ±DC (20 to 150V) (LOW range)
Output (L)
detection
0 to 30V AC, ±DC (0 to 43V) (HIGH range)
0 to 10V AC, ±DC (0 to 15V) (LOW range)
Response time
n MEMORY HiVIEWER 9725
Compatible devices MEMORY HiCORDER 8860 -50, 8861-50, 8860, 8861
Supplied Media
One CD-R disc
Operating environment
Computer running under Windows 2000, XP (32bit), Vista (32bit), or Windows 7 (32-bit/64-bit)
File loading
Readable data formats : Only for 8860 series data (.MEM, .REC,
.FFT, .SEQ, .IDX, .SET)
Maximum file size : 2 GW
File saving
Saved contents: measurement data (binary and ASCII), (partial
saving of the area between cursors A and B), setting conditions,
screen image (BMP, PNG), and calculation results
Display
Waveform display: 1-, 2-, 3-, 4-, 6-, and 8-split screen, horizontal,
vertical, consecutive scroll, and zoom in/out along the time
axis, move the zero position, zoom in/out, setting of variables
independently for each channel
X-Y-axis composite display (for the MEM function only): 1-, 2-, and
4-split display, dot/line interpolation, composite area can be
specified
Numerical display: digital values of waveform data can be displayed
Display sheet: 16 sheets
Display channel count (per sheet): 32 analog channels, 16 logic
channels, 16 calculated waveforms, 8 X-Y-axis composite waveforms
Cursor function: vertical cursor, horizontal cursor, trace cursor, two
cursors (cursor A and cursor B), time and voltage display
Clipboard copy: images on the waveform screen can be transferred
to the clipboard
Print
Supported printer: printer compatible with the OS
Print format: waveform image (1-, 2-, 3-, 4-, 6-, 8-, and
16-split), numerical print, report format, list print, calculation
results, screen image
Print area: the entire area, area between cursors A and B
Print preview: supported
Rising edge 1ms max., falling edge 3ms max. (with HIGH range at
200V DC, LOW range at 100V DC)
Maximum allowable 250Vrms (HIGH range), 150Vrms (LOW range) (the maximum voltage
that can be applied across input pins without damage)
input voltage
Cable length and mass: Main unit cable 1.3 m (4.27 ft), input section cable 46 cm
(1.51 ft), approx. 350 g (12.3 oz)
DIFFERENTIAL PROBE 9322
(Accuracy at 23 ±5°C/73 ±9°F, 35 to 80% rh, after 30 minutes of
warm-up time; accuracy guaranteed for 1 year)
Function
For high-voltage floating measurement, power line surge noise
detection, RMS rectified output measurement
DC mode
For waveform monitor output, frequency characteristics: DC to 10MHz
(±3dB), amplitude accuracy: ±1% of full scale (at max. 1000V DC), ±3%
of full scale (at max. 2000V DC) (full scale: 2000V DC)
AC mode
For detection of power line surge noise, frequency characteristics: 1kHz to 10MHz ±3dB
RMS mode
DC/AC voltage RMS output detection, frequency characteristics: DC, 40Hz to
100kHz, response speed: 200ms or less (400V AC), accuracy: ±1% of full scale
(DC, 40Hz to 1kHz), ±4% of full scale (1kHz to 100kHz) (full scale: 1000V AC)
Input
Input type: balanced differential input, input impedance/capacitance:
H-L 9MΩ/10pF, H/L-unit 4.5MΩ/20pF, Max. rated voltage to earth:
when using grabber clip 1500V AC/DC (CAT II ), 600V AC/DC (CAT III),
when using alligator clip: 1000V AC/DC (CAT II), 600V AC/DC (CAT III)
Data Analysis and Presentation Software
n Features
FlexPro is a powerful data analysis and presentation
software for importing and organizing data from the
8860-50/8861-50 Series.
Note: Product Company: Weisang GmbH (Germany)
Contact: Email: [email protected]
http://www.weisang.com/
FlexPro (data analysis and presentation software)
Overview
• Gather large data sets from multiple channels measured in different
timebases
• Analyze and view results using the easy-to-navigate tabbed window
interface
• Powerful search function lets you shift through large sets of
accumulated data of virtually any size
Functions
Over 100 analysis functions in both the time-domain and frequencydomain, including:
• Fourier Spectral Analysis
• Time Frequency Spectral Analysis
• Harmonic Analysis
• Shock Response Analyses
Active Folder model for setting up a template of both diagrams and
functions that update every time a new signal is captured
Data
Presentation
• Images in all common formats can be imported or exported
• Export analyzed data either in traditional .CSV, .RTF or .TXT formats
or to 3rd party software to accommodate existing database structures
• Easily arrange objects such as 2-D and 3-D diagrams, result tables and
company logos in a report or on website
• Prepared report templates are automatically updated when new
measurements are made
• Make cursor measurements, scrolling and zooming directly from the
report
Maximum allowable input 2000V DC, 1000V AC (CAT II), 600V AC/DC (CAT III)
Output
Power source
Voltage divider for 1/1000 of input, BNC connectors (output switchable
for 3 modes DC, AC, RMS)
(1) Connect the AC ADAPTER 9418-15, (2) Connect to the PROBE POWER
UNIT 9687 via the POWER CORD 9248, (3) Connect to HiCORDER logic
terminal via the POWER CORD 9324 and CONVERSION CABLE 9323,
(4) Connect to the F/V UNIT 8940 via the POWER CORD 9325.
Dimensions and mass: approx. 315.8 (12.43in) W × 29 (1.14in) H × 244.4 (9.62in) D mm,
approx. 1.25 kg (44.1oz) Accessories: None
DC POWER UNIT 9684
Note: Factory-installed option, built in on the bottom case of the main unit
Rated input voltage 12V DC (input range : 10 to 16V DC)
Power requirements 200VA (printer used)
Note: Only one of either the DC Power Unit 9684 or Probe Power Unit 9687 can be installed at any one time. Please contact your
HIOKI representative if concurrent installation is required.
Dimensions and mass: approx. 315.8 (12.43in) W × 18.2 (0.72in) H × 244.4 (9.62in) D mm,
approx. 570 g (20.1oz) Accessories: None
PROBE POWER UNIT 9687
No. of powerd channels
Compatible current probes
Note: Factory-installed option, built in on the bottom case of the main unit
n PC Software Specifications
Wave Viewer (Wv) Software (Application disk CD-R, bundled accessory)
Functions
• Simple display of waveform file
• Text conversion: convert binary data file to text format, with
selectable space or tab separators in addition to CSV, and
specifiable section, thinning available
• Display format settings: scroll functions, enlarge/reduce display, display channel settings
• Others: voltage value trace function, jump to cursor/trigger
position function
Compatible PC
operating systems
Windows 2000/XP/Vista (32-bit), or Windows 7 (32-bit/64-bit)
8 Channels, Output current: Up to 3 A total (Total combined
current consumption of connected probes should be no more than 3 A)
3273 (0.25 A max. current consumption): exclusive, up to 8 probes
3273-50 (0.47 A max. current consumption): exclusive, up to 6 probes
3274 (0.46 A max. current consumption): exclusive, up to 6 probes
3275 (0.60 A max. current consumption): exclusive, up to 5 probes
3276 (0.44 A max. current consumption): exclusive, up to 6 probes
Compatible voltage probes 9322 (0.15 A max. current consumption): exclusive, up to 8 probes
Note: Only one of either the DC Power Unit 9684 or Probe Power Unit 9687 can be installed at any one time. Please contact your
HIOKI representative if concurrent installation is required.
Note: With use of the 8860-50/8861-50 , Wv ver 1.25 or later
Configuration of options Note: Options described as ”factory-installed options” must be specified when ordering and cannot be installed by the user.
Input modules Input cables are not supplied. Please purchase the appropriate cable for the intended application.
Logic signal measurement
Install by inserting into the main unit. Can be replaced by user.
ANALOG UNIT 8956
HIGH RESOLUTION UNIT 8957
16ch SCANNER UNIT 8958
DC/RMS UNIT 8959
STRAIN UNIT 8960
HIGH VOLTAGE UNIT 8961
Recommended
Recommended
4-channel type, for voltage/contact signal
ON/OFF detection (response time 0.1
μsec or higher, miniature terminal type)
..................Maximum 4 units in one MEMORY HiCORDER 8861-50
ANALOG UNIT 8936
VOLTAGE/TEMP UNIT 8937
FFT ANALOG UNIT 8938
STRAIN UNIT 8939
F/V UNIT 8940
4ch ANALOG UNIT 8946
CHARGE UNIT 8947
Voltage measurement
CONVERSION CABLE 9323
Recommended
LOGIC PROBE 9327
4 isolated channels, ON/OFF
detection of AC/DC voltage
(miniature terminal type)
Current measurement
CONVERSION CABLE 9318
(to connect the 9272 - 9279
and the 8940)
UNIVERSAL CLAMP ON CT
9277
Red/black set attaches to the ends
of test leads (9790)
MEMORY HiCORDER 8860-50
Red/black set attaches to the ends
of test leads (9790)
Tip Expanders
Attachment clips are sold separately
from CONNECTION CORD 9790.
Purchase the appropriate attachment
clips for your application separately
*
The MEMORY HiCORDER 8861-50 cannot operate alone. You must
install one or more optional input modules in the unit. When ordering,
specify two memory boards of the same capacity for the 8861-50.
CONVERSION CABLE 9319
*
Factory-installed option. 60 GB
MEMORY BOARD 9715-50
(32 Megaword capacity)
* Only one of either
the DC Power Unit 9684
or Probe Power Unit 9687
can be installed at any one time. Please contact
your HIOKI representative if concurrent installation is required.
MEMORY BOARD 9715-52
100:1 PROBE 9666
Max. rated voltage to earth is same as
for input module, max. input voltage 5
kV peak (up to 1MHz), 1.5 m (4.92 ft)
length
(512 Megaword capacity)
MEMORY BOARD 9715-53
(1 Gigaword capacity)
DC POWER UNIT 9684
Factory-installed option - not user
installable, built in on the bottom case.
12 V DC drive.
MEMORY BACKUP UNIT
9719-50
for use with power supply
3273-50
3276
PROBE POWER UNIT 9687
For up to 2 kV DC or 1 kV AC. Use
with either AC Adapter 9418-15, or
Probe Power Unit 9687 and Power
Cord 9248.
AC ADAPTER 9418-15
3272
3269
CLAMP ON PROBE 3274
POWER SUPPLY 3269
CLAMP ON PROBE 3275
* Either the DC power unit 9684 or the probe
CLAMP ON PROBE 3276
PROBE POWER UNIT 9687
DC to 10MHz wideband response,
mA-class current up to 150A rms
DC to 2MHz wideband response,
mA-class current up to 500A rms
DC to 100MHz wideband response,
mA-class current up to 30A rms
Connect and power up to one CLAMP
ON PROBE to use in combination with
voltage input modules
Connect and power up to four CLAMP
ON PROBEs to use in combination
with voltage input modules
power unit 9687 may be used. If you want to
use both at the same time,
consult us.
Factory-installed option - not user installable, built
in on the bottom case. Simultaneously power up
to at least 5 units of Clamp on Probes 3273-50 to
3276 or Differential Probe 9322. (Actual number
depends on combination of probes.)
Product Company:
Weisang GmbH (Germany)
Contact:
Email: [email protected]
URL: http://www.weisang.com/
Recommended
POWER CORD 9248
FlexPro
MEMORY HiVIEWER 9725
to connect Differential probe
9322 and Probe power unit 9687,
70 cm (2.3 ft) length
FlexPro is a powerful data analysis and presentation
software for importing and organizing data from the
8860 -50 / 8861-50 Series.
Functions identical to those of the 8860s.
Windows 2000/XP/Vista (32-bit), Windows 7
(32/64-bit)
Windows 2000/XP/Vista (32-bit),
Windows 7 (32-bit/64-bit)
WAVE PROCESSOR 9335
Convert data, print and display waveforms.
Note: Supports 8860-50/8860, 8861-50/8861 series
MEM, REC and REC&MEM data recorded using
single-axis sampling only.
Other options
Printer options
RECORDING PAPER 9231
(for A4-printer 8995 only)
A4 width 216 mm (8.50 in) × 30
m (98.43 ft), 6 rolls
Removable storage (CF card)
Not CE marked
Recommended
CONNECTION CORD 9217 CONNECTION CORD 9165
A4 PRINTER UNIT 8995
Cord has insulated BNC connectors at
both ends, and connects to insulated
BNC connectors on input module.
1.7 m (5.58 ft) length
Factory-installed option. Either 8995 or
8995-01 printer can be installed. Printing
width 200 mm (7.87 inch).
Not CE marked
Cord has metallic BNC connectors at
both ends, and connects to metallic BNC
connectors. 1.5 m (4.92 ft) length
RECORDING PAPER 9234
(for A6-printer 8995-01 only)
A6 width 112 mm (4.41 in) × 18
m (59.06 ft), 10 rolls
A6 PRINTER UNIT 8995-01
Factory-installed option. Either 8995 or
8995-01 printer can be installed. Printing
width 100 mm (3.94 inch).
Main unit with memory 32 MW No. of CH.
Input module
8860-50 × 1
(normal choice of the input unit,
up to 200V AC direct input.)
Memory Board 9715-50 × 1 Input cable
CONVERSION ADAPTER 9199
2 ch + logic 16 ch 4 ch + logic 16 ch
CARRYING CASE 9724
For only the 8861-50/8861, hard
trunk type
Banana-to-BNC, use to connect to BNC
terminal on Input Module
6ch + logic 16ch
8ch + logic 16ch
8956 × 1
8956 × 2
8956 × 3
8956 × 4
9198 × 2
9198 × 4
9198 × 6
9198 × 8
PC CARD 2G 9830
Straight Ethernet cable, supplied
with straight to cross conversion
cable, 5 m (16.41 ft) length
For only the 8860-50/8860, hard
trunk type
Paper width 70 to 220 mm (2.76
to 8.66 inch), 100 V AC Only
Supplied with PC
Card adapter
LAN CABLE 9642
CARRYING CASE 9723
PAPER WINDER 220H
Combination example (1)
DC to 50MHz wideband response,
mA-class current up to 30A rms
PC Software
Factory-installed option - not user installable,
built in on the bottom case. Simultaneously
power up to 8 units of Differential Probe
9322. (Max. 3 A output)
For powering Differential probe
9322, 100 to 240 V AC
CLAMP ON PROBE 3273-50
POWER SUPPLY 3272
Factory-installed option. Internal type.
DIFFERENTIAL PROBE 9322
To connect the 3273-50 and the 8940
Note: cannot be used with the 3274, 3275,
3276 to connect the 8940 via this cable
9319
CLAMP ON PROBE 3273-50
DC to 50MHz wideband response,
mA-class current up to 30A rms
HD UNIT 9718-50
MEMORY BOARD 9715-51
3273-50
Current measurement *Connect directly to the analog input module
3274
3275
(128 Megaword capacity)
High-Voltage measurement
Observe waveforms from DC to distorted
AC. DC to 20kHz response, input 500A /
output 2V AC
to connect the 9272 to 9279 and the 8940
Power supply unit for the 9272 to
the 9279 clamp sensors, except
for connecting to the F/V unit
8940, for signal output 9217 is
necessary.
Tip Expanders
9790-02
For high voltage (up to 500 V), 1.8 m
(5.91 ft) length
Max. rated voltage to earth is same as
for input module, max. input voltage 1
kV rms (up to 500 kHz), 1.5 m (4.92 ft)
length
CONVERSION CABLE 9318
MEMORY HiCORDER 8861-50
Tip Expanders
9790-03
CONNECTION CORD 9198 CONNECTION CORD 9197
10:1 PROBE 9665
Observe waveforms from DC to distorted
AC. DC to 100kHz response, input 200A /
output 2V AC
Not CE marked
SENSOR UNIT 9555 -10
Note: Memory boards are not built in as a
standard feature. Choose one board for
Model 8860-50, and two of the same capacity
for the 8861-50, for factory pre-installation.
For low voltage (up to 300 V), 1.7 m
(5.58 ft) length
Use with the Conversion Cable 9318
to connect Model 9272-10 to the F/V
Unit 8940. (Not necessary for when
using the Model 9272 due to different
output wiring specifications.)
UNIVERSAL CLAMP ON CT
9279
* The MEMORY HiCORDER 8860-50 cannot operate alone. You must
install one or more optional input modules in the unit. * When ordering,
specify one memory board for the 8860-50.
CONTACT PIN 9790-03
Tip Expanders
9790-01
Enables observation of AC current
waveforms. Input: 1 to 100kHz, selectable
20 and 200A rms ranges, 2V AC output
CONVERSION CABLE 9705
UNIVERSAL CLAMP ON CT
9278
GRABBER CLIP 9790-02
(Thin Type) CAT II 300 V, ultraflexible 2.8 mm (0.11 in) diameter test
lead cable, 1.5 m (4.92 ft) length
Note: Attachment clips sold separately.
CLAMP ON SENSOR
9272-10
Observe waveforms from DC to distorted
AC. DC to 100kHz response, input 20A /
output 2V AC
ALLIGATOR CLIP 9790-01
Red/black set attaches to the ends
of test leads (9790)
CONNECTION CORD 9790
* To connect the clamp-on sensor via the conversion cable, The
3274, 3275, and 3276 cannot be used for the F/V UNIT 8940
F/V UNIT 8940
for use with general input modules
Recommended
Used for connecting the 9320/9321 and
8860 series MEMORY HiCORDERs,
4-channel type, for voltage/contact signal because the terminal shapes are different.
* This cable is not required for the smallON/OFF detection (response time 0.5
terminal types 9327, 9320-01, and
μsec, miniature terminal type)
9321-01.
LOGIC PROBE 9321-01 LOGIC PROBE 9320-01
Combination example (2)
Main unit with memory 32 MW No. of CH.
Input module
8861-50 × 1
(normal choice of the input unit,
up to 200V AC direct input.)
Memory Board 9715-50 × 2 Input cable
(2 GB capacity)
PC Card Precaution
Use only PC Cards sold by HIOKI.
Compatibility and performance
are not guaranteed for PC cards
made by other manufacturers. You
may be unable to read from or save
data to such cards.
PC CARD 1G 9729
(1 GB capacity)
PC CARD 512M 9728
(512 MB capacity)
PC CARD 256M 9727
(256 MB capacity)
10 ch + logic 16 ch 12 ch + logic 16 ch 14ch + logic 16ch 16ch + logic 16ch
8956 × 5
8956 × 6
8956 × 7
8956 × 8
9198 × 10
9198 × 12
9198 × 14
9198 × 16
Note: Company names and Product names appearing in this catalog are trademarks or registered trademarks of various companies.
HIOKI (Shanghai) Sales & Trading Co., Ltd. :
1608-1610 Shanghai Times Square Office, 93 Huai Hai Zhong Road,
Shanghai, P.R.China POSTCODE: 200021
TEL +86-21-6391-0090/0092 FAX +86-21-6391-0360
http://www.hioki.cn / E-mail: [email protected]
HEAD OFFICE :
81 Koizumi, Ueda, Nagano, 386-1192, Japan
TEL +81-268-28-0562 / FAX +81-268-28-0568
http://www.hioki.co.jp / E-mail: [email protected]
HIOKI USA CORPORATION :
6 Corporate Drive, Cranbury, NJ 08512 USA
TEL +1-609-409-9109 / FAX +1-609-409-9108
http://www.hiokiusa.com / E-mail: [email protected]
DISTRIBUTED BY
Beijing Office :
TEL +86-10-5867-4080/4081 FAX +86-10-5867-4090
E-mail: [email protected]
Guangzhou Office :
TEL +86-20-38392673/2676 FAX +86-20-38392679
E-mail: [email protected]
HIOKI INDIA PRIVATE LIMITED :
Khandela House, 24 Gulmohar Colony Indore 452 018 (M.P.), India
TEL +91-731-4223901, 4223902 FAX +91-731-4223903
http://www.hioki.in / E-mail: [email protected]
All information correct as of Jun. 24, 2010. All specifications are subject to change without notice.
8860-50E5-06E-00KR
Printed in Korea