EL7154 ® Data Sheet May 6, 2005 High Speed, Monolithic Pin Driver Features The EL7154 3-state pin driver is particularly well suited for ATE and level shifting applications. The 4A peak drive capability, makes the EL7154 an excellent choice when driving high speed capacitive lines. • Comparatively low cost The p-channel MOSFET is completely isolated from the power supply, providing a high degree of flexibility. Pin (7) can be grounded, and the output can be taken from pin (8) when a “source follower” output is desired. Then n-channel MOSFET has an isolated drain, but shares a common bus with pre-drivers and level shifter circuits. This is necessary to ensure that the nchannel device can turn off effectively when VL goes below GND. In some power-FET and IGBT applications, negative drive is desirable to insure effective turn-off. The EL7154 can be used in these applications by returning VL to a moderate negative potential. • Clocking speeds up to 10MHz FN7278.1 • 3-State output • 3V and 5V Input compatible • 20ns Switching/delay time • 4A Peak drive • Isolated drains • Low output impedance—2.5Ω • Low quiescent current—5mA • Wide operating voltage—4.5V–16V • Isolated P-channel device • Separate ground and VL pins Pinout • Pb-Free available (RoHS compliant) EL7154 (8-PIN PDIP, SOIC) TOP VIEW Applications • Loaded circuit board testers • Digital testers • Level shifting below GND • IGBT drivers • CCD drivers Ordering Information PACKAGE TAPE & REEL PKG. DWG. # EL7154CN 8-Pin PDIP - MDP0031 EL7154CS 8-Pin SOIC - MDP0027 EL7154CS-T7 8-Pin SOIC 7” MDP0027 EL7154CS-T13 8-Pin SOIC 13” MDP0027 EL7154CSZ (See Note) 8-Pin SOIC (Pb-free) - MDP0027 EL7154CSZ-T7 (See Note) 8-Pin SOIC (Pb-free) 7” MDP0027 EL7154CSZ-T13 (See Note) 8-Pin SOIC (Pb-free) 13” MDP0027 PART NUMBER Truth Table 3-STATE INPUT POUT NOUT 0 0 Open Open 0 1 Open Open 1 0 HIGH Open 1 1 Open LOW Manufactured under U.S. Patent Nos. 5,334,883, #5,341,047, #5,352,578, #5,352,389, #5,351,012, #5,374,898 1 NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-352-6832 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 1996, 2003, 2005. All Rights Reserved All other trademarks mentioned are the property of their respective owners. EL7154 Nominal Operating Voltage Range PIN MIN MAX VL -3 0 VDD–VL 5 15 VH–VL 2 15 -0.5 15 5 15 VDD–VH VDD 2 EL7154 Absolute Maximum Ratings (TA = 25°C) Supply (VDD to VL; VH–VL, VH to GND), V+ to VH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V VL to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5V Input Pins . . . . . . . . . . . . . . . . . -0.3V below VL to +0.3V above VDD Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4A Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C Power Dissipation SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .570mW PDIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1050mW CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA DC Electrical Specifications PARAMETER TA = 25°C, VDD = +12V, VH = +12V, VL = -3V, unless otherwise specified DESCRIPTION TEST CONDITIONS MIN TYP MAX UNITS INPUT VIH Logic “1” Input Voltage IIH Logic “1” Input Current VIL Logic “0” Input Voltage IIL Logic “0” Input Current VHVS Input Hysteresis 2.4 VIH = VDD V 0.1 VIL = 0V 0.1 10 µA 0.6 V 10 µA 0.3 V OUTPUT ROH Pull-Up Resistance IOUT = -100mA 1.5 4 Ω ROL Pull-Down Resistance IOUT = +100mA 2 4 Ω IOUT Output Leakage Current VDD/GND 0.2 10 µA IPK Peak Output Current Source Sink 4.0 4.0 IDC Continuous Output Current Source/Sink IS Power Supply Current Inputs = VDD VS Operating Voltage IG Current to GND (Pin 4) IH Off Leakage at VH A 200 mA POWER SUPPLY AC Electrical Specifications PARAMETER 1 2.5 mA 16 V 1 10 µA 1 10 µA TYP MAX UNITS CL = 100pF 4 25 ns CL = 2000pF 20 CL = 100pF 4 25 ns CL = 2000pF 20 4.5 Pin 8 = 0V TA = 25°C unless otherwise specified DESCRIPTION TEST CONDITIONS MIN SWITCHING CHARACTERISTICS (VDD = VH = 12V; VL = -3V) tR tF Rise Time Fall Time tD-1 Turn-Off Delay Time CL = 2000pF 20 25 ns tD-2 Turn-On Delay Time CL = 2000pF 10 25 ns tD-1 3-State Delay 25 ns tD-2 3-State Delay 25 ns 3 EL7154 Timing Table Standard Test Configuration 4 EL7154 Typical Performance Curves Max Power/Derating Curves Input Current vs Voltage Quiescent Supply Current Average Supply Current vs Voltage and Frequency 5 Switch Threshold vs Supply Voltage Peak Drive vs Supply Voltage “ON” Resistance vs Supply Voltage Rise/Fall Time vs Load EL7154 Typical Applications Adjustable Amplitude Pulse Generator Pin Driver IGBT Driver (with Negative Swing) PMOS Follower Resonant Gate Driver All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 6