5500 IsoWeb Window Framing

5500 Series IsoWeb® Windows
Visionary Design and Advanced Functionality
Combine to Deliver Maximum Results
Southeast Division Police Station, Edmonton, Alberta, Canada
Architect: IBI Group Architects, Engineers, Edmonton, Alberta, Canada
Glazing Contractor: Cantech Glass Contracting Inc., Edmonton, Alberta, Canada
Photo: © CJ Berg Photographics
Providing panoramic views of the outdoors while meeting the
stringent Canadian CAN/CSA-A440 performance requirements is a
tough challenge. Kawneer set out to address the assignment, and
its 5500 Series IsoWeb® Window is the result.
Ideal for new and retrofit construction, the 5500 Series IsoWeb®
Window enables the designer to leverage the vision area while
maintaining the thermal integrity of the exterior façade.
By employing its high-performance glass-reinforced nylon 6/6
IsoWeb® thermal break technology, the 5500 Series IsoWeb ®
Window meets or exceeds the highest performance levels set forth
by CAN/CSA-A440 for windows. With outstanding condensation
resistance and thermal transmittance performance capabilities,
the 5500 Series raises the standards for design, functionality and
performance.
Performance
The high-performing 4" (101.6 mm) deep 5500 IsoWeb® Window
and 5" (127 mm) deep 5525 IsoWeb® Window achieve a significantly
superior condensation index (I value) and thermal transmittance
(U-factor). A recessed interior leg provides the ability to interface
with air and vapor barriers to ensure the continuity of the seal at the
window perimeter.
The windows have a vented and drained rain screen cavity and
accommodate both 1" (25 mm) and 1-3/4" (44 mm) sealed glass units.
The structural aspects of the product are enhanced through the
thermal break connecting the exterior portion of the frame to the
interior portion. The technology permits composite action, thus
achieving greater load resistance while still offering design flexibility.
Additionally, the “top hat” feature of the 5525 IsoWeb® Window
provides a deeper 5" frame for thicker wall construction and greater
structural capability.
Glass is installed and replaced from the interior side of the window.
The 5500 Series IsoWeb® Windows also accept a full range of projectout, project-in and casement vents.
Aesthetics
Kawneer’s 5500 Series IsoWeb® Window offers the versatility in
design and the high performance required for today‘s building
applications. Whether it is the overall flush appearance provided by
the 5500 IsoWeb® Window with its with extreme frontal placement of
glass or the distinctive “top hat” accent feature of the 5525 IsoWeb®
Window you are looking for, this window provides a solution.
Performance Test Standards*
Windows are tested in accordance with
CSA
A440-00 and AAMA/WDMA/CSA 101/I.S.2/A440-08 (NAFS 08).
Air Performance
ASTM E 283
Water Performance
ASTM E 331
Uniform Static Structural Performance
ASTM E 330
Life CycleAAMA 910
Forced Entry
ASTM F 588
ThermalCSA A440-00, AAMA 507, AAMA 1503,
NFRC 102, NFRC 100/200/500
*Test results available from Kawneer. Contact your Kawneer sales representative for
more information.
Fabrication and Installation
The 5500 Series IsoWeb® Window can be installed in punched
and strip openings. A specially designed coupling mullion allows
the windows to be installed in a multi-modular strip application.
Horizontal muntins are available as well.
4"
2-5/8"
2-7/8"
66.7 mm
73.0 mm
Standard Mullion
Coupling Mullion
Kawneer Company, Inc.
Technology Park / Atlanta
555 Guthridge Court
Norcross, GA 30092
© Kawneer Company, Inc. 2012
kawneer.com
kawneergreen.com
770 . 449 . 5555
LITHO IN U.S.A.
Form No. 12-2161
5525 IsoWeb® Window
with “Top Hat” Accent Feature
The vents have 45° mitered corners, which give the window a smooth
and attractive appearance. Other options include Euro-groove multipoint locking hardware and multiple locking handle styles and finishes.
The 5500 Series IsoWeb® Windows can fit the aesthetics of almost
any project with a maximum vision area and high overall thermal
integrity, coupled with considerable flexibility in design selection.
101.6 mm
4"
101.6 mm
Comparison of standard mullion with coupling mullion, which allows
for multi-modular or strip window applications (5500 IsoWeb® Window
shown, 5525 IsoWeb® Window similar)
5500 IsoWeb® Window
with Flush Appearance
OCTOBER, 2010
5500 ISOWEB ® WINDOW
INDEX
E.C. 97911-22
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
PICTORIAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FIXED FRAMING DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
MISCELLANEOUS DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
VENT DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7
THERMAL TRANSMITTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
STRUCTURAL LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED
ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT
CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING
HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR.
Metric (SI) conversion figures are included throughout these details for reference.
Numbers in parentheses ( ) are millimeters unless otherwise noted.
© Kawneer Company, Inc., 2010
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Architects - These concepts have been expanded and modified to afford you design freedom.
Please contact your Kawneer representative for further assistance.
The extrusions and window types illustrated in this catalog are standard products for Kawneer.
The following metric (SI) units are found in these details:
m - meter
cm - centimeter
mm - millimeter
s - second
Pa - pascal
MPa - megapascal
Kawneer reserves the right to change configurations without prior notice when deemed necessary
for product improvement.
kawneer.com
1
5500 ISOWEB ® WINDOW
FEATURES
OCTOBER, 2010
E.C. 97911-22
FEATURES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
24mm ISOWEB ® glass-reinforced nylon 6/6 thermal break provides:
Improved condensation resistance and thermal transmittance performance capability
Rigid profiles with composite structural performance
Exterior / interior finish options
Meets or exceeds the highest performance levels of CSA standard CAN/CSA-A440 Windows
Vented and drained rain screen glazing cavity
Coped joinery with screw spline fastening
Recessed interior leg on perimeter section to accept air and / or vapour barrier membranes
Glazing flanges on same plane providing flush appearance
Accommodates 25mm and 44mm sealed unit thicknesses
Glass installed and replaced from interior
Tremco VISIONstrip ® exterior glazing system
EPDM rubber interior gasket pre-loaded to snap-in glass stop
Accepts Ventrow inserts
Accepts a full range of Kawneer's series AA900 project-in, project-out and casements vents
45° mitered vent and frame corners
Accentuated tubular profiles
Factory fabricated and assembled
Euro-groove multi-point locking hardware
Multiple locking handle styles and finishes
Triple glazing available
kawneer.com
© Kawneer Company, Inc., 2010
EPDM rubber air seal gasket along perimeter of 25mm sealed unit
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
© Kawneer Company, Inc., 2010
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
OCTOBER, 2010
E.C. 97911-22
kawneer.com
5500 ISOWEB ® WINDOW
PICTORIAL VIEW
3
5500 ISOWEB ® WINDOW
4
OCTOBER, 2010
FIXED FRAMING DETAILS
E.C. 97911-22
SCALE 1/4 FULL SIZE
Overall frame width
Max. 18'-0" (5500)
5
2
3
1
5
823-203
823-201
823-202
823-203
823-204
823-205
823-040
2 5/8"
66.7
823-203
4
HEAD
5
INTERMEDIATE
HORIZONTAL
4"
101.6
823-202
2
TUBULAR
MULLION
1
JAMB
6
SILL
3
MULTI-MODULAR
COUPLING MULLION
1 3/4"
44.5
823-202
823-040
Overall frame height
5
INTERMEDIATE
HORIZONTAL
1 3/4"
44.5
4
HEAD
3
JAMB
2 7/8"
73.0
2 5/8"
66.7
Overall frame width
Max. 18'-0" (5500)
823-201
823-040
2 5/8"
66.7
2
TUBULAR
MULLION
1 3/4"
44.5
823-203
4"
101.6
1 3/4"
44.5
1
JAMB
1 3/4"
44.5
Overall frame height
2 5/8"
66.7
Overall frame width
Max. 18'-0" (5500)
1 3/4"
44.5
1 3/4"
44.5
4"
101.6
4"
101.6
823-040
6
SILL
3
6
6
823-201
2
823-201
kawneer.com
© Kawneer Company, Inc., 2010
1
4
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
4
Overall frame height
Overall frame height
Overall frame width
Max. 18'-0" (5500)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
MULTI-MODULAR STRIP WINDOW
PUNCHED OPENING WITH VERTICALS
1 3/4"
44.5
© Kawneer Company, Inc., 2010
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
4"
101.6
11/2"
38.1
1 3/4"
44.5
2 1/2"
63.5
823-059
kawneer.com
Sealant
heel bead
823-202
2 3/8"
60.3
E.C. 97911-22
TRIPLE GLAZING
(ACCEPTS 44mm SEALED UNITS)
90° INSIDE CORNER
823-203 (Mod.)
4"
101.6
1 3/4"
44.5
3 1/8"
79.4
4"
101.6
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
OCTOBER, 2010
5500 ISOWEB ® WINDOW
MISCELLANEOUS DETAILS
SCALE 1/4 FULL SIZE
DEFLECTION HEAD
(ALLOWS +- 5/8" (15.9) MOVEMENT)
823-203
823-041
823-208
2 5/8"
66.7
823-040
3 9/16"
90.5
4"
101.6
823-040
517-123
823-207
823-040
4"
101.6
90° OUTSIDE CORNER
823-040
823-201
823-203
1 3/4"
44.5
TYPICAL SILL DETAILS
4"
101.6
823-040
823-202
5
1
4
1/8 "
3.2
1 3/4 "
44.5
2
4
4
VENT
SILL
Window Dimension
Fixed Framing D.L.O.
5 3/16"
131.8
6 1/16"
154.0
1
VENT JAMB
2
VENT JAMB
2 5/8"
66.7
4"
101.6
3 (Sim.)
1/8 "
3.2
2 5/8 "
66.7
kawneer.com
1/8 "
3.2
2 5/8 "
66.7
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Window Dimension
L. H. SHOWN, R. H. OPPOSITE
© Kawneer Company, Inc., 2010
3
Fixed Framing D.L.O.
VENT DETAILS
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
3
VENT
HEAD
6 1/16 "
154.0
5500 ISOWEB ® WINDOW
1/8 "
3.2
1 3/4 "
44.5
OPEN-IN CASEMENT
(SPI)
5 3/16"
131.8
OPEN-IN VENT
(BPI)
4"
101.6
1
2 5/8"
66.7
6
OCTOBER, 2010
E.C. 97911-22
SCALE 1/4 FULL SIZE
NOTE: TYPICAL WINDOW CONFIGURATIONS SHOWN, REFER TO AATM 900 ISOWEB® WINDOW PRODUCT LITERATURE
FOR PERFORMANCE RATINGS, SIZE LIMITATIONS AND AVAILABLE OPTIONS.
kawneer.com
3 (Sim.)
3
1
4
1/8 "
3.2
1 3/4 "
44.5
Fixed Framing D.L.O.
4
4
VENT
SILL
Window Dimension
Fixed Framing D.L.O.
2 5/8 "
66.7
5 13/32"
137.3
6 9/32"
159.5
1
VENT JAMB
2
VENT JAMB
2 5/8"
66.7
1/8 "
3.2
Window Dimension
1/8 "
3.2
2 5/8 "
66.7
E.C. 97911-22
1/8 "
3.2
2
1 3/4"
44.5
1
6 9/32"
159.5
3
VENT
HEAD
5 13/32"
137.3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
OPEN-OUT VENT
(TPO)
4"
101.6
2 5/8"
66.7
© Kawneer Company, Inc., 2010
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
OCTOBER, 2010
5500 ISOWEB ® WINDOW
7
VENT DETAILS
SCALE 1/4 FULL SIZE
NOTE: TYPICAL WINDOW CONFIGURATIONS SHOWN, REFER TO AATM 900 ISOWEB® WINDOW PRODUCT LITERATURE
FOR PERFORMANCE RATINGS, SIZE LIMITATIONS AND AVAILABLE OPTIONS.
4"
101.6
OPEN-OUT CASEMENT
(SPO)
R. H. SHOWN, L. H. OPPOSITE
2
8
5500 ISOWEB ® WINDOW
OCTOBER, 2010
THERMAL TRANSMITTANCE
E.C. 97911-22
The window thermal transmittance values (U - values) shown in the chart below are based on CSA - A440.2 "Energy Performance
Evaluation of Windows and Sliding Glass Doors." U - values of the center of glass, edge of glass, and frame areas were computed using
the VISION and FRAME thermal simulation programs. Overall window U - values were calculated using the following relationship:
U w = (U c A c + U e A e + U f A f )/A w
where
U w = U-value of complete window product
U c = calculated center of glass U-value
U e = calculated edge of glass U-value
U f = calculated frame U-value
A c = center of glass area
A e = edge of glass area
A f = frame area
A w = total window area
OVERALL WINDOW U-VALUE (U w )
For fixed and operating window configurations as shown with height (h) equal to width (w).
1
A = 6mm clear / 1/2" air / 6mm low-e / metal spacer
B = 6mm clear / 1/2" argon / 6mm low-e 1 / metal spacer
3
A
B
0.40 C
D
E
0.20
2
F
1
C = 6mm clear / 1/2" argon / 6mm low-e 1 / warm edge spacer 3
D = 6mm clear / 1/2" argon / 6mm low-e 2 / warm edge spacer 3
1
E = 6mm clear / 1/2" argon / 6mm low-e
F = 6mm clear / 1/2" argon / 6mm low-e
2
/ 1/2" argon / 6mm low-e
/ 1/2" argon / 6mm low-e
1
2
0
/ metal spacer
/ warm edge spacer
3
20
40
60
AREA IN SQUARE FEET
1 - low-e coating emittance = 0.1
2 - low-e coating emittance = 0.03
3 - Edgetech Super "U" Spacer ®
NOTES: THE ABOVE SEALED UNIT GLAZING OPTIONS ARE PRESENTED FOR THE PURPOSES OF ILLUSTRATING THERMAL
PERFORMANCE CAPABILITIES.
FOR WINDOWS WITH HEIGHT NOT EQUAL TO WIDTH, WHEN ADDING INTERMEDIATE VERTICALS OR HORIZONTALS,
OR DIFFERENT GLASS INFILL, THE OVERALL WINDOW U - VALUE MAY VARY.
THE SPECIFIER SHOULD SELECT GLASS TO MEET THE PERFORMANCE REQUIREMENTS OF THE PROJECT.
kawneer.com
© Kawneer Company, Inc., 2010
SEALED UNIT GLAZING TYPE
0.60
WINDOW U w IN W / m 2 °C
WINDOW U w IN BTU / hr ft 2 °F
w
4
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
AREA IN SQUARE METRES
2
4
0.80
h
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
For some regions and projects there may be minimum energy efficiency requirements for the building envelope, and its components,
including windows. The shading coefficient (SC) and the thermal transmittance (U - value) of the window is then required to determine
whether the building design complies with the specified energy requirements. Shading coefficient depends on the glass selected and
should be obtained from the glass supplier. The U - value of the window varies with the type of glass and sealed unit edge construction,
the window frame, and the relative areas of these components.
5500 ISOWEB ® WINDOW
OCTOBER, 2010
9
STRUCTURAL LIMITATIONS
E.C. 97911-22
Calculations are based on CAN3-S157 "Strength Design in Aluminum" in accordance with the National Building Code of Canada and an
allowable deflection of 1/175 of mullion span.
WINDLOAD LIMITATIONS
WITHOUT HORIZONTALS
WITH HORIZONTALS
WIDTH IN METRES
4"
101.6
10
3.0
A
8
B
2.5
C
D
E
7
6
3
4
5
2.0
6
7
8
A
8
C
3
4
2.5
A
3.0
B
9
C
D
E
8
2.5
7
2.0
823-205
11
7
4
5
6
7
WIDTH IN FEET
8
9
WIDTH IN METRES
1.5
2.0
2.5
1.0
3.0
9
A
8
5
9
2.5
B
7
C
D
E
6
3
8
10
6
5
6
WITH HORIZONTALS
4"
101.6
823-204
5
WIDTH IN FEET
HEIGHT IN FEET
HEIGHT IN FEET
2.0
2.0
D
E
A = 15 p.s.f. (0.72 kPa.)
B = 20 p.s.f. (0.96 kPa.)
C = 25 p.s.f. (1.20 kPa.)
D = 30 p.s.f. (1.44 kPa.)
E = 35 p.s.f. (1.68 kPa.)
HEIGHT IN METRES
11
1.5
2.5
B
7
WIDTH IN METRES
1.0
2.5
9
5
WITHOUT HORIZONTALS
2.0
3.0
6
9
WIDTH IN FEET
1.5
10
HEIGHT IN FEET
9
5
11
1.0
HEIGHT IN METRES
2.5
823-203
10
3
4
5
6
7
WIDTH IN FEET
2.0
8
9
DEADLOAD LIMITATIONS
WIDTH IN METRES
2.0
2.5
1.5
1.0
7
2.0
6
B
5
A B
A
1.5
4
3
kawneer.com
1.0
3
4
5
6
7
WIDTH IN FEET
8
9
HEIGHT IN METRES
8
HEIGHT IN FEET
© Kawneer Company, Inc., 2010
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2.0
HEIGHT IN METRES
1.5
HEIGHT IN METRES
11
HEIGHT IN FEET
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
WIDTH IN METRES
1.0
Intermediate Horizontal
Intermediate Horizontal 823-203
Over Ventilator
I = 0.17 in4 (7.20 x 10 4 mm4 )
(Maximum Deflection 1/16")
S = 0.20 in3 (0.32 x 10 4 mm3 )
Intermediate Horizontal
Over Fixed Lite
(Maximum Deflection 1/8")
Curves are for sealed units
with setting blocks 3" (76 mm)
from the ends of the lite.
A - Double glazed sealed unit
with (2) 6mm lites.
B - Triple glazed sealed unit
with (3) 6mm lites
kawneer.com
© Kawneer Company, Inc., 2010
BLANK PAGE
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
5500 ISOWEB ® WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
10
OCTOBER, 2010
E.C. 97911-22