OCTOBER, 2010 5500 ISOWEB ® WINDOW INDEX E.C. 97911-22 FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PICTORIAL VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FIXED FRAMING DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 MISCELLANEOUS DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 VENT DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7 THERMAL TRANSMITTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 STRUCTURAL LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. © Kawneer Company, Inc., 2010 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Architects - These concepts have been expanded and modified to afford you design freedom. Please contact your Kawneer representative for further assistance. The extrusions and window types illustrated in this catalog are standard products for Kawneer. The following metric (SI) units are found in these details: m - meter cm - centimeter mm - millimeter s - second Pa - pascal MPa - megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement. kawneer.com 1 5500 ISOWEB ® WINDOW FEATURES OCTOBER, 2010 E.C. 97911-22 FEATURES Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 24mm ISOWEB ® glass-reinforced nylon 6/6 thermal break provides: Improved condensation resistance and thermal transmittance performance capability Rigid profiles with composite structural performance Exterior / interior finish options Meets or exceeds the highest performance levels of CSA standard CAN/CSA-A440 Windows Vented and drained rain screen glazing cavity Coped joinery with screw spline fastening Recessed interior leg on perimeter section to accept air and / or vapour barrier membranes Glazing flanges on same plane providing flush appearance Accommodates 25mm and 44mm sealed unit thicknesses Glass installed and replaced from interior Tremco VISIONstrip ® exterior glazing system EPDM rubber interior gasket pre-loaded to snap-in glass stop Accepts Ventrow inserts Accepts a full range of Kawneer's series AA900 project-in, project-out and casements vents 45° mitered vent and frame corners Accentuated tubular profiles Factory fabricated and assembled Euro-groove multi-point locking hardware Multiple locking handle styles and finishes Triple glazing available kawneer.com © Kawneer Company, Inc., 2010 EPDM rubber air seal gasket along perimeter of 25mm sealed unit Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 © Kawneer Company, Inc., 2010 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. OCTOBER, 2010 E.C. 97911-22 kawneer.com 5500 ISOWEB ® WINDOW PICTORIAL VIEW 3 5500 ISOWEB ® WINDOW 4 OCTOBER, 2010 FIXED FRAMING DETAILS E.C. 97911-22 SCALE 1/4 FULL SIZE Overall frame width Max. 18'-0" (5500) 5 2 3 1 5 823-203 823-201 823-202 823-203 823-204 823-205 823-040 2 5/8" 66.7 823-203 4 HEAD 5 INTERMEDIATE HORIZONTAL 4" 101.6 823-202 2 TUBULAR MULLION 1 JAMB 6 SILL 3 MULTI-MODULAR COUPLING MULLION 1 3/4" 44.5 823-202 823-040 Overall frame height 5 INTERMEDIATE HORIZONTAL 1 3/4" 44.5 4 HEAD 3 JAMB 2 7/8" 73.0 2 5/8" 66.7 Overall frame width Max. 18'-0" (5500) 823-201 823-040 2 5/8" 66.7 2 TUBULAR MULLION 1 3/4" 44.5 823-203 4" 101.6 1 3/4" 44.5 1 JAMB 1 3/4" 44.5 Overall frame height 2 5/8" 66.7 Overall frame width Max. 18'-0" (5500) 1 3/4" 44.5 1 3/4" 44.5 4" 101.6 4" 101.6 823-040 6 SILL 3 6 6 823-201 2 823-201 kawneer.com © Kawneer Company, Inc., 2010 1 4 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 4 Overall frame height Overall frame height Overall frame width Max. 18'-0" (5500) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MULTI-MODULAR STRIP WINDOW PUNCHED OPENING WITH VERTICALS 1 3/4" 44.5 © Kawneer Company, Inc., 2010 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 4" 101.6 11/2" 38.1 1 3/4" 44.5 2 1/2" 63.5 823-059 kawneer.com Sealant heel bead 823-202 2 3/8" 60.3 E.C. 97911-22 TRIPLE GLAZING (ACCEPTS 44mm SEALED UNITS) 90° INSIDE CORNER 823-203 (Mod.) 4" 101.6 1 3/4" 44.5 3 1/8" 79.4 4" 101.6 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. OCTOBER, 2010 5500 ISOWEB ® WINDOW MISCELLANEOUS DETAILS SCALE 1/4 FULL SIZE DEFLECTION HEAD (ALLOWS +- 5/8" (15.9) MOVEMENT) 823-203 823-041 823-208 2 5/8" 66.7 823-040 3 9/16" 90.5 4" 101.6 823-040 517-123 823-207 823-040 4" 101.6 90° OUTSIDE CORNER 823-040 823-201 823-203 1 3/4" 44.5 TYPICAL SILL DETAILS 4" 101.6 823-040 823-202 5 1 4 1/8 " 3.2 1 3/4 " 44.5 2 4 4 VENT SILL Window Dimension Fixed Framing D.L.O. 5 3/16" 131.8 6 1/16" 154.0 1 VENT JAMB 2 VENT JAMB 2 5/8" 66.7 4" 101.6 3 (Sim.) 1/8 " 3.2 2 5/8 " 66.7 kawneer.com 1/8 " 3.2 2 5/8 " 66.7 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Window Dimension L. H. SHOWN, R. H. OPPOSITE © Kawneer Company, Inc., 2010 3 Fixed Framing D.L.O. VENT DETAILS Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 3 VENT HEAD 6 1/16 " 154.0 5500 ISOWEB ® WINDOW 1/8 " 3.2 1 3/4 " 44.5 OPEN-IN CASEMENT (SPI) 5 3/16" 131.8 OPEN-IN VENT (BPI) 4" 101.6 1 2 5/8" 66.7 6 OCTOBER, 2010 E.C. 97911-22 SCALE 1/4 FULL SIZE NOTE: TYPICAL WINDOW CONFIGURATIONS SHOWN, REFER TO AATM 900 ISOWEB® WINDOW PRODUCT LITERATURE FOR PERFORMANCE RATINGS, SIZE LIMITATIONS AND AVAILABLE OPTIONS. kawneer.com 3 (Sim.) 3 1 4 1/8 " 3.2 1 3/4 " 44.5 Fixed Framing D.L.O. 4 4 VENT SILL Window Dimension Fixed Framing D.L.O. 2 5/8 " 66.7 5 13/32" 137.3 6 9/32" 159.5 1 VENT JAMB 2 VENT JAMB 2 5/8" 66.7 1/8 " 3.2 Window Dimension 1/8 " 3.2 2 5/8 " 66.7 E.C. 97911-22 1/8 " 3.2 2 1 3/4" 44.5 1 6 9/32" 159.5 3 VENT HEAD 5 13/32" 137.3 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. OPEN-OUT VENT (TPO) 4" 101.6 2 5/8" 66.7 © Kawneer Company, Inc., 2010 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. OCTOBER, 2010 5500 ISOWEB ® WINDOW 7 VENT DETAILS SCALE 1/4 FULL SIZE NOTE: TYPICAL WINDOW CONFIGURATIONS SHOWN, REFER TO AATM 900 ISOWEB® WINDOW PRODUCT LITERATURE FOR PERFORMANCE RATINGS, SIZE LIMITATIONS AND AVAILABLE OPTIONS. 4" 101.6 OPEN-OUT CASEMENT (SPO) R. H. SHOWN, L. H. OPPOSITE 2 8 5500 ISOWEB ® WINDOW OCTOBER, 2010 THERMAL TRANSMITTANCE E.C. 97911-22 The window thermal transmittance values (U - values) shown in the chart below are based on CSA - A440.2 "Energy Performance Evaluation of Windows and Sliding Glass Doors." U - values of the center of glass, edge of glass, and frame areas were computed using the VISION and FRAME thermal simulation programs. Overall window U - values were calculated using the following relationship: U w = (U c A c + U e A e + U f A f )/A w where U w = U-value of complete window product U c = calculated center of glass U-value U e = calculated edge of glass U-value U f = calculated frame U-value A c = center of glass area A e = edge of glass area A f = frame area A w = total window area OVERALL WINDOW U-VALUE (U w ) For fixed and operating window configurations as shown with height (h) equal to width (w). 1 A = 6mm clear / 1/2" air / 6mm low-e / metal spacer B = 6mm clear / 1/2" argon / 6mm low-e 1 / metal spacer 3 A B 0.40 C D E 0.20 2 F 1 C = 6mm clear / 1/2" argon / 6mm low-e 1 / warm edge spacer 3 D = 6mm clear / 1/2" argon / 6mm low-e 2 / warm edge spacer 3 1 E = 6mm clear / 1/2" argon / 6mm low-e F = 6mm clear / 1/2" argon / 6mm low-e 2 / 1/2" argon / 6mm low-e / 1/2" argon / 6mm low-e 1 2 0 / metal spacer / warm edge spacer 3 20 40 60 AREA IN SQUARE FEET 1 - low-e coating emittance = 0.1 2 - low-e coating emittance = 0.03 3 - Edgetech Super "U" Spacer ® NOTES: THE ABOVE SEALED UNIT GLAZING OPTIONS ARE PRESENTED FOR THE PURPOSES OF ILLUSTRATING THERMAL PERFORMANCE CAPABILITIES. FOR WINDOWS WITH HEIGHT NOT EQUAL TO WIDTH, WHEN ADDING INTERMEDIATE VERTICALS OR HORIZONTALS, OR DIFFERENT GLASS INFILL, THE OVERALL WINDOW U - VALUE MAY VARY. THE SPECIFIER SHOULD SELECT GLASS TO MEET THE PERFORMANCE REQUIREMENTS OF THE PROJECT. kawneer.com © Kawneer Company, Inc., 2010 SEALED UNIT GLAZING TYPE 0.60 WINDOW U w IN W / m 2 °C WINDOW U w IN BTU / hr ft 2 °F w 4 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. AREA IN SQUARE METRES 2 4 0.80 h Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. For some regions and projects there may be minimum energy efficiency requirements for the building envelope, and its components, including windows. The shading coefficient (SC) and the thermal transmittance (U - value) of the window is then required to determine whether the building design complies with the specified energy requirements. Shading coefficient depends on the glass selected and should be obtained from the glass supplier. The U - value of the window varies with the type of glass and sealed unit edge construction, the window frame, and the relative areas of these components. 5500 ISOWEB ® WINDOW OCTOBER, 2010 9 STRUCTURAL LIMITATIONS E.C. 97911-22 Calculations are based on CAN3-S157 "Strength Design in Aluminum" in accordance with the National Building Code of Canada and an allowable deflection of 1/175 of mullion span. WINDLOAD LIMITATIONS WITHOUT HORIZONTALS WITH HORIZONTALS WIDTH IN METRES 4" 101.6 10 3.0 A 8 B 2.5 C D E 7 6 3 4 5 2.0 6 7 8 A 8 C 3 4 2.5 A 3.0 B 9 C D E 8 2.5 7 2.0 823-205 11 7 4 5 6 7 WIDTH IN FEET 8 9 WIDTH IN METRES 1.5 2.0 2.5 1.0 3.0 9 A 8 5 9 2.5 B 7 C D E 6 3 8 10 6 5 6 WITH HORIZONTALS 4" 101.6 823-204 5 WIDTH IN FEET HEIGHT IN FEET HEIGHT IN FEET 2.0 2.0 D E A = 15 p.s.f. (0.72 kPa.) B = 20 p.s.f. (0.96 kPa.) C = 25 p.s.f. (1.20 kPa.) D = 30 p.s.f. (1.44 kPa.) E = 35 p.s.f. (1.68 kPa.) HEIGHT IN METRES 11 1.5 2.5 B 7 WIDTH IN METRES 1.0 2.5 9 5 WITHOUT HORIZONTALS 2.0 3.0 6 9 WIDTH IN FEET 1.5 10 HEIGHT IN FEET 9 5 11 1.0 HEIGHT IN METRES 2.5 823-203 10 3 4 5 6 7 WIDTH IN FEET 2.0 8 9 DEADLOAD LIMITATIONS WIDTH IN METRES 2.0 2.5 1.5 1.0 7 2.0 6 B 5 A B A 1.5 4 3 kawneer.com 1.0 3 4 5 6 7 WIDTH IN FEET 8 9 HEIGHT IN METRES 8 HEIGHT IN FEET © Kawneer Company, Inc., 2010 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2.0 HEIGHT IN METRES 1.5 HEIGHT IN METRES 11 HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. WIDTH IN METRES 1.0 Intermediate Horizontal Intermediate Horizontal 823-203 Over Ventilator I = 0.17 in4 (7.20 x 10 4 mm4 ) (Maximum Deflection 1/16") S = 0.20 in3 (0.32 x 10 4 mm3 ) Intermediate Horizontal Over Fixed Lite (Maximum Deflection 1/8") Curves are for sealed units with setting blocks 3" (76 mm) from the ends of the lite. A - Double glazed sealed unit with (2) 6mm lites. B - Triple glazed sealed unit with (3) 6mm lites kawneer.com © Kawneer Company, Inc., 2010 BLANK PAGE Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 5500 ISOWEB ® WINDOW Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 10 OCTOBER, 2010 E.C. 97911-22