sma2404m ds en

500V breakdown voltage Full bridge driver IC SMA2404M (Negative drive system)
■Features
■Package
●Encapsulate MOSFET (4pieces) and a control MIC
●Sanken original ZIP package
between roots
between tips
between roots
●500V breakdown voltage negative power supply drive system
●Suitable for inverter element for HID ballast unit
between tips
between roots
■Absolute maximum ratings
No.
Item
Symbol
Unit
Rating
Conditions
between Power GND and –HV
480
1
Power Source Voltage
VM
planer state
Tj=-40∼-20℃
V
between Power GND and –HV
500
Tj=-20∼+150℃
2
Input Voltage
VIN
V
15
Tj=-40∼+150℃
3
Operating Voltage
Vcc
V
15
Tj=-40∼+150℃
4
Output Voltage
VOUT
V
500
Ta=25℃
5
Output Current
IOUT(DC)
A
7
Ta=25℃
4
Ta=25℃
6
Total Power Dissipation
PD
W
20
Tc=25℃
7
Operation Temperature
Topr
℃
-40∼+150
35W HID Lamps Driver
8
Storage Temperature
Tstg
℃
-40∼+150
9
Junction Temperature
Tj
℃
150
■Circuit block diagram
■Electrical characteristics (Tj=25℃)
No.
Item
Symbol
Value
Unit
Min.
1
2
3
Power MOSFET Output
Breakdown Voltage
Power MOSFET Output
Leakage Current
Power MOSFET Output
On-State Voltage
4
Quiescent Circuit Current
5
Operating Circuit Current
6
Input Threshold Voltage
7
8
9
10
11
Low side MOSFET Gate
Drive Voltage
Delay time
Power MOSFET
On-State Resistance
Power MOSFET
Input Capacitance
Diode Reverse Recovery Time
BVOUT
V
IOUT(off)
μA
VOUT(on)
V
Conditions
Typ.
Max.
500
IOUT=100μA
100
VOUT=500V
IOUT=0.4A, VIN(or VGL)=10V
0.28
0.40
0.52
1.4
2.0
2.6
IOUT=2.0A, VIN(or VGL)=10V
Icc1
mA
3.0
Vcc=10V, VM=VIN=0V
Icc2
mA
4.0
Vcc=10V, VM=400V, VIN=0V
Icc3
mA
4.0
Vcc=10V, VM=400V
VIN1(orVIN2)=10V
VIH
V
VIL
V
VGL
V
■Typical connection diagram
0.8・Vcc
Vcc=7∼15V
0.2・Vcc
8.0
0.7・Vcc
td(on)
μs
1.5
td(off)
μs
2.0
⊿td
μs
RDS(on)
Ω
Ciss
pF
trr
ns
0.7
Vcc=7∼15V
Vcc=VIN=10V, VM=85V
IO=0.41A
2.5
⊿td=td(off)-td(on)
1.3
ID=0.4A,
VGS=10V
860
VDS=10V,
VGS=0V
f=1MHz
300
ISD=±100mA
1.0
Recommended input signal dead time
No.
Item
Symbol
Unit
1
dV/dt
dV/dt
V/μs
2
Recommended dead time
td
μs
Value
Min.
Typ.
Max.
2
4.5
Conditions
Ta=25℃,Vcc=10V,VM=400V
Ta=−40∼150℃
■Timing Chart
lead tip miscutting