INTERSIL EL2072

®
EL2072
UCT
T
PROD ACEMEN at
E
T
L
E
r
L
P
e
E
O
t
n
OBS NDED R port Ce /tsc
E
p
m
M
u
o
S
c
ECOM echnical .intersil.
December 1995, Rev. E
w
NO R Data
T Sheet
w
r
u
w
o
r
ct
Lo
a
I
t
S
n
o
R
c
-INTE
1-888
FN7033
730MHz Closed Loop Buffer
Features
The EL2072 is a wide bandwidth, fast
settling monolithic buffer built using an
advanced complementary bipolar
process. This buffer is closed loop to achieve lower output
impedance and higher gain accuracy. Designed for closedloop unity gain, the EL2072 has a 730MHz -3dB bandwidth
and 5ns settling to 0.2% while consuming only 15mA of
supply current.
• 730MHz -3dB bandwidth (0.5VPP)
• 5ns settling to 0.2%
• VS = ±5V @ 15mA
• Low distortion: HD2, HD3 of -65dBc at 20MHz
• Overload/short-circuit protected
• Closed-loop, unity gain
The EL2072 is an obvious high-performance solution for
video distribution and line-driving applications. With low
15mA supply current and a 70mA output drive, performance
in these areas is assured.
• Low cost
The EL2072's settling to 0.2% in 5ns, low distortion, and
ability to drive capacitive loads make it an ideal flash A/D
driver. The wide 730MHz bandwidth and extremely linear
phase allow unmatched signal fidelity.
• Video buffer
The EL2072 can be used inside an amplifier loop or PLL as
its wide bandwidth and fast rise time have minimal effect on
loop dynamics.
• High-speed A/D buffer
Elantec products and facilities comply with MIL-I-45028A,
and other applicable quality specifications. For information
on Elantec's processing, see Elantec document QRA-1:
Elantec's Processing, Monolithic Integrated Circuits.
• Direct replacement for CLC110
Applications
• Video distribution
• HDTV buffer
• Photodiode, CCD preamps
• IF processors
• High-speed communications
Ordering Information
PART
NUMBER
Pinout
EL2072
(8-PIN PDIP SO)
TOP VIEW
TEMP.
RANGE
PACKAGE
PKG. NO.
EL2072CN
-40°C to +85°C
8-Pin PDIP
MDP0031
EL2072CS
-40°C to +85°C
8-Pin SO
MDP0027
Manufactured under U.S. Patent No. 4,893,091
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc.
All other trademarks mentioned are the property of their respective owners.
EL2072
Absolute Maximum Ratings (TA = 25°C)
Supply Voltage (VS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±7V
Output Current
Output is short-circuit protected to ground, however, maximum reliability is
obtained if IOUT does not exceed 70mA.
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±VS
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-60°C to +150°C
Thermal Resistance. . . . . . . . . . . . . . . . . . . . . . . . .θJA = 95°C/W PDIP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . θJA = 175°C/W SO
Note: See EL2071/EL2171 for Thermal Impedance curves.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
PARAMETER
VOS
TCVOS
IB
VS = ±5V, RL = 100Ω, RS = 50Ω unless otherwise specified
DESCRIPTION
TEST CONDITIONS
Output Offset Voltage
TEMP
MIN
TYP
MAX
UNITS
2.0
8.0
mV
TMIN
16.0
mV
TMAX
13.0
mV
µV/°C
25°C
Average Offset Voltage Drift
Input Bias Current
25°C - TMAX
20.0
50.0
25°C - TMIN
20.0
100.0
25°C, TMAX
10.0
50.0
µA
100.0
µA
nA/°C
TMIN
TCIB
AV
ILIN
Average Input Bias Current Drift
Small Signal Gain
Integral End Point linearity
PSRR
Power Supply Rejection Ratio
IS
Supply Current—Quiescent
RIN
Input Resistance
CIN
RL = 100Ω
±2V F.S.
25°C - TMAX
200.0
300.0
25°C - TMIN
200.0
700.0
25°C
0.96
TMIN, TMAX
0.95
25°C
Input Capacitance
V/V
0.2
%F.S.
TMIN
0.8
%F.S.
TMAX
0.3
%F.S.
45.0
All
65.0
15.0
160.0
50.0
kΩ
TMAX
200.0
kΩ
1.6
25°C
VOUT
Output Current
Output Voltage Swing
2
RL = 100Ω
mA
TMIN
2.0
TMIN, TMAX
IOUT
20.0
100.0
25°C
Output Impedance (DC)
dB
25°C
TMIN, TMAX
ROUT
V/V
0.4
All
No Load
0.98
25°C, TMAX
50.0
TMIN
45.0
25°C, TMAX
±3.2
TMIN
±3.0
70.0
kΩ
2.2
pF
2.5
pF
3.0
Ω
3.5
Ω
mA
mA
±4.0
V
V
EL2072
AC Electrical Specifications
PARAMETER
VS = ±5V, RL = 100Ω, RS = 50Ω unless otherwise specified
DESCRIPTION
TEST CONDITIONS
TEMP
MIN
TYP
MAX
UNITS
25°C
400.0
730.0
TMIN
400.0
MHz
TMAX
300.0
MHz
25°C
55.0
TMIN, TMAX
50.0
FREQUENCY RESPONSE
SSBW
LSBW
-3dB Bandwidth
(VOUT < 0.5VPP)
-3dB Bandwidth
(VOUT = 5.0VPP)
MHz
90.0
MHz
MHz
GAIN FLATNESS
GFPL
GFR
GDL
Peaking VOUT < 0.5VPP
Rolloff VOUT < 0.5VPP
Group Delay
< 200MHz
< 200MHz
< 200MHz
25°C
0.0
0.5
dB
TMAX
0.6
dB
TMIN
0.8
dB
0.8
dB
TMIN
1.0
dB
TMAX
1.2
dB
1.0
ns
1.2
ns
1.5
°
2.0
°
1.0
ns
1.4
ns
7.5
ns
8.5
ns
25°C
0.0
25°C, TMIN
0.75
TMAX
LPD
Linear Phase Deviation
VOUT < 0.5VPP
< 200MHz
25°C, TMIN
0.7
TMAX
TIME-DOMAIN RESPONSE
TR1, TF1
Rise Time, Fall Time
Input Signal Rise/Fall = 300ps
0.5V Step
Rise Time, Fall Time
Input Signal Rise/Fall ð 1ns
5.0V Step
TS1
Settling Time to 0.2%
Input Signal Rise/Fall ð 1ns
2.0V Step
All
5.0
10.0
ns
OS
Overshoot
Input Signal Rise/Fall = 300ps
0.5V Step
25°C
0.0
10.0
%
15.0
%
TR2, TF2
SR
25°C, TMIN
0.4
TMAX
25°C
4.5
TMIN, TMAX
TMIN, TMAX
Slew Rate
25°C
500.0
TMIN, TMAX
450.0
800.0
V/µs
V/µs
DISTORTION
HD2
HD2A
HD3
HD3A
2nd Harmonic Distortion
at 20MHz
2VPP
2nd Harmonic Distortion
at 50MHz
2VPP
3rd Harmonic Distortion
at 20MHz
2VPP
3rd Harmonic Distortion
at 50MHz
2VPP
3
25°C
-50.0
dBc
TMIN
-48.0
dBc
TMAX
-55.0
dBc
-45.0
dBc
-40.0
dBc
-55.0
dBc
-55.0
dBc
-50.0
dBc
-45.0
dBc
25°C, TMAX
-55.0
-50.0
TMIN
25°C
-65.0
TMIN, TMAX
25°C, TMIN
TMAX
-60.0
EL2072
AC Electrical Specifications
PARAMETER
VS = ±5V, RL = 100Ω, RS = 50Ω unless otherwise specified (Continued)
DESCRIPTION
TEST CONDITIONS
TEMP
MIN
TYP
MAX
UNITS
-158.0
-155.0
dBm (1Hz)
-154.0
dBm (1Hz)
57.0
µV
63.0
µV
EQUIVALENT INPUT NOISE
NF
INV
Noise Floor
> 100kHz
25°C, TMIN
Integrated Noise
100kHz to 200MHz
25°C, TMIN
TMAX
4
TMAX
40.0
EL2072
Typical Performance Curves
Forward Gain and Phase
Gain Flatness & Deviation
from Linear Phase
Reverse Gain and phase
Input Impedance
Output Impedance
Recommended RS vs
Load Capacitance
Integral Linearity Error
Frequency Response vs
RLOAD
|S21| vs CLOAD
with Recommended Rs
Small Signal
Pulse Response
2nd Harmonic Distortion
5
Large Signal
Pulse Response
3rd Harmonic Distortion
Long-Term
Settling Time
2-Tone, 3rd Order
Intermodulation Intercept
EL2072
Burn-In Circuit
Printed Circuit Layout
As with any high-frequency device, good PCB layout is
necessary for optimum performance. This is especially
important for the EL2072, which has a typical bandwidth of
730MHz. Ground plane construction is a requirement, as is
good power-supply bypassing close to the package. A
closely-placed 0.01µF ceramic capacitor between each
supply pin and the ground plane is usually sufficient
decoupling.
Pins 2, 3, 6, and 7 should be connected to the ground-plane
to minimize capacitive feedthrough, and all input and output
traces should be laid out as transmission lines and
terminated as close to the EL2072 package as possible.
Increasing capacitance on the output of the EL2072 will add
phase shift, decreasing phase margin and increasing
frequency-response peaking. A small series resistor before
the capacitance decouples this effect, and should be used
for large capacitance values. Please refer to the graphs for
the appropriate resistor value to be used.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
6