User's Manual

ICO-200 Series
Remote Field Controller
User’s Manual
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
Copyright 2009 AXIOMTEK Co., Ltd.
All Rights Reserved
April, Version A1
Printed in Taiwan
ii
Safety Approvals
u
CE Marking
u
FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.
iii
Safety Precautions
Before getting started, read the following important cautions.
1. The ICO-200 Series does not come equipped with an
operating system. An operating system must be loaded first
before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the ICO-200 Series before
making any installation. Be sure both the system and the
external devices are turned OFF. Sudden surge of power could
ruin sensitive components. Make sure the ICO-200 Series is
properly grounded.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
®
®
Intel and Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft
Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties of their
respective owners.
iv
Table of Contents
Disclaimers ........................................................................................................ ii
Safety Approvals............................................................................................... iii
FCC Compliance ............................................................................................... iii
Safety Precautions............................................................................................ iv
Chapter 1 Introduction.....................................................................1
1.1
1.2
General Description............................................................................... 1
Specifications........................................................................................ 2
1.2.1
Main CPU board ............................................................................. 2
1.2.2
I/O System...................................................................................... 2
1.2.3
System Specification ...................................................................... 3
1.3
Dimensions ........................................................................................... 4
1.4
I/O Outlets............................................................................................. 5
1.5
Package list........................................................................................... 6
Chapter 2 Hardware Installation .....................................................8
2.1
2.2
Installing the CompactFlash Card ......................................................... 8
Installing the Hard Drive ........................................ 錯誤! 尚未定義書籤。
2.3
Installing PC/I04 .................................................... 錯誤! 尚未定義書籤。
2.4
2.5
2.6
2.7
Serial Port Interface ............................................................................ 10
Ethernet .............................................................................................. 12
Mounting Way: Wall Mount ................................................................. 12
Mini-PCI WLAN Module (optional)....................................................... 13
Chapter 3 Driver Installation .........................................................16
3.1
3.2
3.3
3.4
3.5
3.6
Network Controller............................................................................... 17
AES Driver Installation ........................................................................ 20
VGA Driver Installation ........................................................................ 24
PCI Bridge Driver Installation .............................................................. 28
Audio Driver Installation ...................................................................... 32
WLAN Driver Installation ....................................... 錯誤! 尚未定義書籤。
Chapter 4 Remote Monitoring Tool ..............................................36
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
Remote Tool Installation...................................................................... 37
Monitoring Setting ............................................................................... 38
Alarm Setting ...................................................................................... 40
Notification Setting .............................................................................. 43
Security Setting ................................................................................... 44
Logging Setting ................................................................................... 45
Watchdog Setting................................................................................ 46
Version................................................................................................ 47
v
MEMO
vi
ICO-200 Series User’s Manual
Chapter 1
Introduction
This chapter contains general information and detailed specifications
about the ICO-200 Series. Chapter 1 includes the following sections:
n
General Description
n
Specification
n
Dimensions
n
I/O Outlets
n
Package List
1.1
General Description
The ICO-200 Series is a compact field controller designed for remote
management application. Equipped with AMD LX800 processor, the
ICO-200 Series features high reliability and expansion capability.
This controller has a slim mechanism design and adopts din-rail
mounting to fit in any space-limited environment. Besides, the ICO200 offers the remote management tools of “Remote Monitoring”,
“Remote Alarm”, “Remote Diagnosis” and ”Security”, to enable easy
and efficient management for remote environment anytime, anywhere
over a network.
Introduction
1
ICO-200 Series User’s Manual
Therefore, the ICO-200 Series is ideally suited for use in applications
like unmanned room, factory automation, industrial machine and more.
1.2
Specifications
1.2.1 Main CPU board
l
CPU
l
n AMD LX800 500MHz
System Chipset
n
AMD LX + CS5536AD
BIOS
l
n
Phoenix-Award 4Mbit with RPL/PXE LAN Boot ROM,
SmartView and Customer CMOS Backup
System Memory
l
n
One 200-pin DDR SODIMM, maximum up to 1GB
1.2.2 I/O System
l
Standard I/O
n
Two serial ports (1 x RS-232, 1 x RS-232/422/485)
n
One VGA port
n
One PS/2 for Keyboard and Mouse Interface
n
l
Two USB Ports 2.0 compliant
Ethernet
l
n Two RTL8139DL Fast Ethernet
Expansion
n
One Mini-PCI
CompactFlash Socket
l
n
2
One CompactFlash Type II Socket
Introduction
ICO-200 Series User’s Manual
1.2.3 System Specification
l
Disk Drive Housing
l
n One CompactFlash Type II Socket
DC 24V power supply
l
Heat dispensing design
l
Weight
l
n 1.2 Kgs
Dimension (main body size)
n
l
160.5 x 111.8 x 53.35 mm
Operating temperature
l
n O° to 45°C ; Relative umidity:50%
Relative humidity
n
l
10% to 95% @ 40° C, non-condensing
Altitude
l
n 10,000 ft. (3,000 meters
Vibration (operating)
n
l
5 to 500 Hz, 2 G random
Shock (operating)
n
10 G peak acceleration (11 msec. duration)
NOTE All specifications and images are subject to change
without notice.
Introduction
3
ICO-200 Series User’s Manual
1.3
Dimensions
The ICO-200 Series dimensions and outlines are shown as below:
4
Introduction
ICO-200 Series User’s Manual
1.4
I/O Outlets
The following figure helps you locate each I/O connector of the ICO200 Series.
1
2
3
4
5
6
7
No.
8
Connector
No.
Connector
1
COM 1 (RS-232/422/485)
5
PS/2 for Keyboard/Mouse
2
COM 2 (RS-232)
2 x USB 2.0
6
7
Ethernet (RJ45)
3
4
Ethernet (RJ45)
8
DC power connector
Introduction
VGA
5
ICO-200 Series User’s Manual
1.5
Package list
Other than the ICO-200 system, the following items should be bundled
in the package:
1. ICO-200 x 1
2. DIN rail bracket x 1
3. PS/2 Splitter – Y Cable x 1
4. Driver CD x1
If you can not find this package or any items are missing, please
contact AXIOMTEK distributors immediately.
6
Introduction
ICO-200 Series User’s Manual
MEMO
Introduction
7
ICO-200 Series User’s Manual
Chapter 2
Hardware Installation
The ICO-200 provides you with multiple I/O ports and flexible
expansions to meet different demands for PCMCIA, WLAN modules,
and so on. This chapter will show you how to install the hardware. They
are:
n
n
n
n
n
n
DRAM
CompactFlash Card
Serial Port
Ethernet
Mounting Way
Mini-PCI module
2.1 Installing the DRAM and CompactFlash
Card
The system offers one 200-pin DDR SODIMM socket, maximum up to
1GB, and one CF slot for users to install CompactFlash card. Please
follow these instructions and illustrations to install the DRAM and
CompactFlash card:
Step 1
8
Loosen five screws on the chassis.
Hardware Installation
ICO-200 Series User’s Manual
Step 2
Push back the cover to remove it.
è
Step 3
Insert the DRAM to the socket.
è
Hardware Installation
9
ICO-200 Series User’s Manual
Step 4
Insert the CF card to the CF slot.
è
2.2
Serial Port Interface
The ICO-200 has two onboard serial ports, COM1 (RS-232/422/485)
and COM2 (RS-232).
The pin assignments are listed below:
Pin
Description
1
Data Carrier Detect (DCD)
2
Receive Data (RXD)
3
Transmit Data (TXD)
4
Data Terminal Ready (DTR)
5
Ground (GND)
6
Data Set Ready (DSR)
7
Request to Send (RTS)
8
Clear to Send (CTS)
9
Ring Indicator (RI)
In addition, COM1 can be set for RS-232/422/485 by jumper. The jump
setting is listed as below:
10
Hardware Installation
ICO-200 Series User’s Manual
Description Function
COM1
Jumper Setting
RS-232
(Default)
JP10
JP5
JP7
RS-422
JP10
JP5
JP7
RS-485
JP10
JP5
JP7
COM1 (CN13) RS-422/485 Pin Assignment Table
Pin #
1
2
3
4
5
6
7
8
9
Hardware Installation
Signal Name
RS-422
RS-485
TXTX+
RX+
RXNo connector
No connector
No connector
No connector
GND
DATADATA+
No connector
No connector
No connector
No connector
No connector
No connector
GND
11
ICO-200 Series User’s Manual
2.3
Ethernet
The ICO-200 supports the NE2000 compatible Ethernet (RJ-45)
interface. For network connection, just plug in one cable end of the
ICO-200 10/100 Base-T Hub into the standard RJ-45 connector. The
pin assignment of the RJ-45 is listed below:
Pin
1
2
3
4
5
6
7
8
2.4
Signal
TX+ (Data transmission positive
TX- (Data transmission negative)
Rx+(Data reception positive)
RJ45 termination
RJ45 termination
Rx- (Data reception negative)
RJ45 termination
RJ45 termination
1 2 3 4 5 6 7 8
RJ-45
Mounting Way: Din-rail
The ICO-200 is designed for Din-rail application. To mount the ICO200, the standard set of mounting kit will be bundled with the
system packaging.
Step 1
Screw the Din-rail mount kit on the back of the chassis.
è
12
Hardware Installation
ICO-200 Series User’s Manual
2.5
Mini-PCI Module
ICO-200 offers one mini-PCI slot to install a mini-PCI card. Please refer
to the following instructions and illustrations for installation:
Step 1
Take off the cover.
Step 2 Pull down the front cover and loosen four screws on the
mainboard.
Hardware Installation
13
ICO-200 Series User’s Manual
Step 3
Take off the mainboard and turn it around.
Step 4
Insert the Mini-PCI module.
è
14
Hardware Installation
ICO-200 Series User’s Manual
MEMO
Hardware Installation
15
ICO-200 Series User’s Manual
Chapter 3
Driver Installation
The ICO-200 Series supports Windows XP/2000. To facilitate the
installation of system drivers, you need to carefully read the Chapter 3
for detailed instructions before installing.
\ICO series\ICO-200\Driver
16
Driver Installation
ICO-200 Series User’s Manual
3.1
Network Controller
After you start Windows, a message “Found New Hardware – Network
Controller” will automatically appear on the screen, and automatic
installation will go on.
If it doesn’t start the automatic installation, please follow the procedures
below to manually intall this new hardware:
1. Access the “Control Panel”.
Driver Installation
17
ICO-200 Series User’s Manual
2.
18
Click on the “System” icon, and a “System Properties” tag
pops out. Please select the “Hardware” item, and click the
“Device Manager” button.
Driver Installation
ICO-200 Series User’s Manual
3.
The “Device Manager” window pops out. Execute the “Scan”
function.
4. This hardware installation is finished.
Driver Installation
19
ICO-200 Series User’s Manual
3.2
AES Driver Installation
You can install a LX processor driver through the “Device Manager” by
following these steps:
1. Select the icon “Entertainment Encryption/Decryption
Controller”, and click the right mouse button to update the AES
driver.
20
Driver Installation
ICO-200 Series User’s Manual
2.
A Hardware Update Wizard screen pops out. Make your
selection, and click “Next” to continue.
3.
Click the item to install the software, and click “Next”.
Driver Installation
21
ICO-200 Series User’s Manual
4. Click the “Browse” button and search for the location: “E:\ICO
series\ICO-200\Driver\Step 1. AES
5. Please wait while the wizard is installing the software.
22
Driver Installation
ICO-200 Series User’s Manual
6.
Click the “Finish” button to complete this software installation.
Driver Installation
23
ICO-200 Series User’s Manual
3.3
VGA Driver Installation
You can install a Graphic driver through the “Device Manager” by
following these steps:
1. Select the icon “Video Controller (VGA Compatible)”, and click
the right mouse button to update the VGA driver.
24
Driver Installation
ICO-200 Series User’s Manual
2.
A Hardware Update Wizard screen pops out. Make your
selection, and click “Next” to continue.
3.
Click the item to install the software, and click “Next”.
Driver Installation
25
ICO-200 Series User’s Manual
4. Click the “Browse” button and search for the location: “E:\ICO
series\ICO-200\Driver\Step 2. VGA
5. Please wait while the wizard is installing the software.
6. Click the “Finish” button to complete this software installation.
26
Driver Installation
ICO-200 Series User’s Manual
Driver Installation
27
ICO-200 Series User’s Manual
3.4
PCI Bridge Driver Installation
You can install a PCI Bridge driver through the “Device Manager” by
following these steps:
1. Select the icon “Other PCI Bridge Device”, and click the right
mouse button to update the PCI Bridge driver.
28
Driver Installation
ICO-200 Series User’s Manual
2.
A Hardware Update Wizard screen pops out. Make your
selection, and click “Next” to continue.
3.
Click the item to install the software, and click “Next”.
Driver Installation
29
ICO-200 Series User’s Manual
4. Click the “Browse” button and search for the location: “E:\ICO
series\ICO-200\Driver\Step 3. PCI Bridge
5. Please wait while the wizard is installing the software.
30
Driver Installation
ICO-200 Series User’s Manual
6. This software installation is finished.
Driver Installation
31
ICO-200 Series User’s Manual
3.5
Audio Driver Installation
You can install an Audio driver through the “Device Manager” by
following these steps:
1. Select the icon “Multimedia Audio Controller”, and click the
right mouse button to update the Audio driver.
32
Driver Installation
ICO-200 Series User’s Manual
2.
A Hardware Update Wizard screen pops out. Make your
selection, and click “Next” to continue.
3.
Click the item to install the software, and click “Next”.
Driver Installation
33
ICO-200 Series User’s Manual
4. Click the “Browse” button and search for the location: “E:\ICO
series\ICO-200\Driver\Step 4. Audio
5. Please wait while the wizard is installing the software.
34
Driver Installation
ICO-200 Series User’s Manual
6. Click the “Finish” button to complete this software installation.
Driver Installation
35
ICO-200 Series User’s Manual
Chapter 4
Remote Monitoring Tool
The ICO-200 Series is equipped with a remote monitoring program,
which has these remote functions, monitor, alarm, security, watchdog,
and so on. To facilitate these functions, you need to carefully read the
Chapter 4 for detailed instructions.
\ICO series\ICO-200\Driver
36
Remote Monitoring Tool
ICO-200 Series User’s Manual
4.1
Remote Tool Installation
Please follow these procedures for this tool installation:
1. \ICO series\ICO-200\Driver\Step 6. R @Tools
2. Execute “[email protected]”.
Remote Monitoring Tool
37
ICO-200 Series User’s Manual
4.2
Monitoring Setting
The remote monitoring contains these functions illustrated as below:
1. Users can obtain BIOS information such as CPU usage, CPU
voltage, CPU temperature, fan speed, battery, and Watchdog
status.
2. Users can set up how long this tool will retrieve the data from
BIOS. Users can also start or stop this function.
3. R @Tool provides users with 3 * DI & 5 * DO to make the
connection with the DIO module. Users can set up which DO
status will be monitored.
38
Remote Monitoring Tool
ICO-200 Series User’s Manual
4.
The color of word can be changed if the status is abnormal.
5.
After the SMTP setting is done, users can type in the IP
address of ICO-200 that can monitor the controller’s status:
Remote Monitoring Tool
39
ICO-200 Series User’s Manual
4.3
Alarm Setting
Users can make these settings to work a remote alarm that can identify
each necessary situation for warning the operator, such as CPU
overheating, CPU over-voltage, main power failure, battery on, system
resetting, and so on. If anything abnormal happens, ICO-200 will alarm
the operator by e-mail or soft modem.
Users need to click the “Save” button to save any setting changes.
40
Remote Monitoring Tool
ICO-200 Series User’s Manual
1.
After the “Notification setting” is done, the operator will receive the
alarming e-mail from ICO-200, if anything abnormal happens:
2.
Open the attached file and execute it. The remote window pops
out as below:
Remote Monitoring Tool
41
ICO-200 Series User’s Manual
3.
After passing the identity verification, the operator can take over
ICO-200 as following.
42
Remote Monitoring Tool
ICO-200 Series User’s Manual
4.4
Notification Setting
When the alarmimg occurs, ICO-200 will inform the operator by
e-mail. Users need to set up a few of parameters for before initiating
the Notification function.
1.
Users need to set up the parameters for SMTP setting, such as
server name, port, username and password.
2.
Under the “SMTP setting”, users can decide who will receive the
alarming message from ICO-200.
3.
Users need to click the “Save” button to save any setting changes.
Remote Monitoring Tool
43
ICO-200 Series User’s Manual
4.5
Security Setting
Users can go to the tag “Security Setting” to set up who is authorized to
access ICO-200. Even authorized users’ IP addresses could be locked
up.
Users need to click the “Save” button to save any setting changes.
44
Remote Monitoring Tool
ICO-200 Series User’s Manual
4.6
Logging Setting
Any abnormal issues of ICO-200 can be recorded. The operator can
refer to this tag through the monitoring function.
Users need to click the “Save” button to save any setting changes.
Remote Monitoring Tool
45
ICO-200 Series User’s Manual
4.7
Watchdog Setting
ICO-200 can not execute the alarming function if the system crashed. In
order to avoid this problem, ICO-200 has been equipped with the
Watchdog Timer. Users are able to shut down ICO-200 remotely.
ICO-200 will be automatically restarted after users have set up the
Watchdog Timer.
46
Remote Monitoring Tool
ICO-200 Series User’s Manual
4.8
Version
If you have any problems about this remote tool, you can have the
program version number from this “Version” tag. Please contact us in
reference to it.
Remote Monitoring Tool
47
ICO-200 Series User’s Manual
MEMO
48
Remote Monitoring Tool