DATASHEET

ISL97636A
®
Data Sheet
May 9, 2008
6-Channel LED Driver
Features
The ISL97636A is an integrated power LED driver that
controls 6 channels of LED current for LCD backlight
applications. The ISL97636A is capable of driving typically
54 (6x9) pieces of 3.5V/30mA or 60 (6x10) pieces of
3.2V/20mA LEDs. The ISL97636A’s contains 6 channels of
voltage controlled current sources with typical currents
matching of ±1%, which compensate for the non-uniformity
effect of forward voltages variance in the LED stacks. To
minimize the voltage headroom and power loss in the typical
multi-strings operation, the ISL97636A features a dynamic
headroom control that monitors the highest LED forward
voltage string and uses its feedback signal for output
regulation.
• 6 channels
The LED brightness can be pulse width modulated with an
applied PWM signal from DC to audio noise free 20kHz.
The ISL97636A features extensive protection functions that
include string open and short circuit detections, OVP, OTP,
thermal shutdown and an optional input overcurrent
protection with master fault disconnect switch.
• 6V to 24V Input
• 34.5V Output Max
• Drive Maximally 54 (3.5V/30mA each) or 60 (3.2V/20mA
each) LEDs
• Current Matching ±1% Typ
• Dynamic Headroom Control
• PWM Signal up to 20kHz Dimming
• Protections
- String Open Circuit Detection
- String Short Circuit Detection with Selectable Thresholds
- Over-Temperature Protection
- Overvoltage Protection
- Optional Input Overcurrent Protection w/Disconnect SW
• 1.2MHz Switching Frequency
• 24 Ld 4mmx4mm QFN Package
Available in the 24 Ld 4mmx4mm QFN, the ISL97636A
operates from -40°C to +85°C with input voltage ranges from
6V to 24V for high LEDs count applications.
• Pb-Free (RoHS compliant)
Ordering Information
• Notebook Displays LED Backlighting
PART
NUMBER
(Note)
ISL97636AIRZ*
FN6566.0
Applications
• LCD Monitor LED Backlighting
PART
MARKING
PACKAGE
(Pb-free)
976 36AIRZ
24 Ld 4x4 QFN
PKG.
DWG. #
L24.4x4D
• Automotive Displays LED Backlighting
• Automotive or Traffic Lighting
*Add “-T” or “-TK” suffix for tape and reel. Please refer to TB347 for
details on reel specifications
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets; molding compounds/die attach
materials and 100% matte tin plate PLUS ANNEAL - e3 termination
finish, which is RoHS compliant and compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J STD-020.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2008. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ISL97636A
Typical Application Circuit
VBL+ = 6V TO 24V
VOUT = 34.5V, 30mA PER STRING
ISL97636A
21 FAULT
LX 19
LX 20
23 VIN
24 VDC
OVP 16
PGND 17
PGND 18
22 COMP
IIN0 15
6 PWMI/EN IIN1 14
11 RSET
IIN2 13
IIN3 12
IIN4 10
5 GND
2
IIN5 9
FN6566.0
May 9, 2008
ISL97636A
Block Diagram
34.5V, 30mA PER STRING
(6 x 9 = 54 WHITE LEDS)
VBL+ = 6V TO 24V
FAULT
VIN
LX
O/P SHORT
VDC
REG
OVP
FAULT DETECT
OSC AND
RAMP
COMP
Σ =0
FET
DRIVER
LOGIC
IMAX ILIMIT
PGND
IIN0
COMP
GM
AMP
REFERENCE
GENERATOR
HIGHEST VF
STRING
DETECT
IIN5
+
-
+
-
RSET
OC, SC
DETECT
OC, SC
DETECT
FAULT DETECT
ISL97636A
GND
FAULT DETECT
TEMP
SENSOR
+
-
PWMI/EN
PWM
GENERATOR
PWM/OC/SC
FAULT/DETECT
FIGURE 1. ISL97636A BLOCK DIAGRAM
3
FN6566.0
May 9, 2008
ISL97636A
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
VIN, FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 24V
VDC, COMP, RSET, EN/PWM . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V
OVP, IIN0 - IIN5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 28V
LX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 36V
PGND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V
Above voltage ratings are all with respect to GND pin
Thermal Resistance (Typical, Notes 1, 2)
24 Ld QFN . . . . . . . . . . . . . . . . . . . . . .
Thermal Characterization (Typical, Note 3)
θJA (°C/W)
39
θJC (°C/W)
2
PSIJT (°C/W)
24 Ld QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
~0.7
Maximum Continuous Junction Temperature . . . . . . . . . . . . +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
1. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
2. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside assumed under ideal case temperature.
3. PSIJT is the junction-to-top thermal resistance. If the package top temperature can be measured, with this rating then the die junction temperature
can be estimated more accurately than the θJC and θJC thermal resistance ratings.
4. Limits established by characterization and are not production tested.
Electrical Specifications
PARAMETER
All specifications below are tested at TA = -40°C to +85°C; VIN = 12V, EN = 5V, RSET = 36.6kΩ; Parameters
with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits
established by characterization and are not production tested
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
24
V
5
µA
34.5
V
2.8
V
GENERAL
VIN
Backlight Supply Voltage
IVIN_STBY
VIN Shutdown Current
VOUT
Output Voltage
Vuvlo
Undervoltage Lockout Threshold
Vuvlo_hys
Undervoltage Lockout Hysteresis
SS
Soft-start
≤ 9 LEDs per channel
(3.5V/30mA type)
6
2.45
300
mV
1
ms
PWM GENERATOR
EN/PWM
EN/PWM Voltage Range
2.7
5.5
ENmin
Minimum Enable Signal
tMAX_PWM_OFF
Maximum PWMI Off Time Before
Shutdown
EN/PWMI toggles
VDC
LDO Output Voltage
VIN > 6V
IVDC_STBY
Standby Current
EN/PWM = 0V
IVDC
Active Current
EN/PWM = 5V
10
VLDO
VDC LDO Dropout Voltage
VIN > 5.5V, 30mA
30
Boost FET Current Limit
TA = +25°C
2.3
TA = -40°C, +85°C
2.2
V
40
µs
28
ms
REGULATOR
5.0
5.5
V
20
µA
mA
200
mV
3.2
A
BOOST
SWILimit
rDS(ON)
Internal Boost Switch ON-Resistance
4
A
130
260
mΩ
FN6566.0
May 9, 2008
ISL97636A
Electrical Specifications
PARAMETER
Eff_peak
All specifications below are tested at TA = -40°C to +85°C; VIN = 12V, EN = 5V, RSET = 36.6kΩ; Parameters
with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits
established by characterization and are not production tested (Continued)
DESCRIPTION
Peak Efficiency
CONDITION
MIN
TYP
MAX
UNIT
VIN = 18V, 54 LEDs,
20mA each, L = 8.2µH
with DCR 106mΩ,
TA = +25°C
91
%
VIN = 12V, 54 LEDs,
20mA each, L = 8.2µH
with DCR 106mΩ,
TA = +25°C
88
%
VIN = 6V, 54 LEDs,
20mA each, L = 8.2µH
with DCR 106mΩ,
TA = +25°C
86
%
0.1
%
ΔIOUT/ΔVIN
Line Regulation
Dmax
Boost Maximum Duty Cycle
Dmin
Boost Minimum Duty Cycle
fS
Switching Frequency
ILX_leakage
LX Leakage Current
VLX = 36V, EN = 0
Imatch
Channel-to-Channel Current Matching
IOUT = 30mA
IACC
Current Accuracy
82
%
7
1.0
1.2
%
1.3
MHz
10
µA
+3.5
%
REFERENCE
-3.5
±1
±3
%
FAULT DETECTION
VSC
Short Circuit Threshold
PWM Dimming = 100%
7.8
8
8.8
Vtemp_acc
Over-Temperature Threshold Accuracy
VOVPlo
Overvoltage Limit on OVP Pin
OVPhys
OVP Hysteresis
20
mV
OVPfault
OVP Short Detection Fault Level
300
mV
100
mV
°C
5
1.17
1.2
V
1.23
V
CURRENT SOURCES
Vheadroom
Dominant Channel Current Source
Headroom at IIN Pin
ILED = 20mA
TA = +25°C
VRSET
Voltage at RSET Pin
RSET = 36.6kΩ
ILEDmax
Maximum LED Current Per Channel
RSET = 20.9kΩ
Ifault
Fault Pull-down Current
VIN = 12V
Vfault
FAULT Clamp Voltage with Respect to VIN VIN = 12, VIN - Vfault
IlxStartup
LX Start-up Current
680
700
720
35
mV
mA
FAULT PIN
5
VDC = 5.2V
10
18
30
7.5
1
2.7
µA
V
7
mA
FN6566.0
May 9, 2008
ISL97636A
Typical Performance Curves
92
90
90
88
88
86
86
EFFICIENCY (%)
84
7S6P - 18V
82
7S6P - 12V
80
9S6P - 18V
9S6P - 12V
78
7S6P - 6V
76
74
72
EFFICIENCY (%)
92
68
9S6P - 18V 9S6P - 6V
80
7S6P - 18V
78
20
40
60
80
IO (mA)
100
120
7S6P - 6V
74
L = 10µH
IHLP-2525BD-01
DCR = 129mΩ
ISAT = 2.5A
68
0
140
FIGURE 2. EFFICIENCY, L = 8.2µH WITH DCR = 106mΩ,
CO = 4x4.7µF/50V
9S6P - 12V
76
66
0
20
40
60
80
IO (mA)
100
140
1.2
L = 10µH
DCR ~ 500mΩ
88 <1mm HEIGHT
90
1.0
CURRENT VARIATION (%)
0.8
86
9S6P - 18V
84
9S6P - 12V
7S6P - 12V
82
80
7S6P - 18V
78
76
9S6P - 6V
74
72
7S6P - 6V
70
0.6
0.4
0.2
20mA
0.0
-0.2
-0.4
-0.6
-0.8
-1.0
68
0
20
40
60
80
IO (mA)
100
120
-1.2
140
4
FIGURE 4. 3 EFFICIENCY, L = 10µH WITH DCR = 500mΩ,
1mm, CO = 4x4.7µF/50V
6
8
10
12
14 16
VIN (V)
18
20
24
26
1.0
6P9S = 54 LEDs
VIN = 12V
0.015
CURRENT MATCHING (%)
12V/1mA
0.010
12V/20mA
0.005
0
-0.005
6V/20mA
-0.010
6V/1mA
0.9
20kHz
0.8
0.7
200Hz
0.6
10kHz
1kHz
100Hz
-0.015
-0.020
22
FIGURE 5. CURRENT REGULATION
0.020
CURRENT MATCHING
120
FIGURE 3. EFFICIENCY, L = 10µH WITH DCR = 129mΩ,
CO = 4x4.7µF/50V
92
EFFICIENCY (%)
82
70
66
66
84
72
L = 8.2µH
IHLP-2525BD-01
DCR = 106mΩ
ISAT = 3A
9S6P - 6V
70
7S6P - 12V
Ch 0
Ch 1
Ch 2
Ch 3
CHANNELS
Ch 4
Ch 5
FIGURE 6. CHANNEL-TO-CHANNEL CURRENT MATCHING
6
0.5
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
PWM DUTY CYCLE
FIGURE 7. CURRENT MATCHING vs DUTY CYCLE vs
DIMMING FREQUENCY
FN6566.0
May 9, 2008
ISL97636A
Typical Performance Curves (Continued)
180
TOTAL OUTPUT CURRENT (mA)
160
6 CHANNELS
9 LEDs PER CHANNEL
VIN = 12V
140
120
VIN = 6V
100
80
60
40
VIN = 18V
20
0
0
10
20
30
40
50
60
70
PWM DUTY CYCLE%
80
90
100
FIGURE 8. PWM DIMMING LINEARITY
FIGURE 9. LX, VIIN, IL AND IO AT PWM DIMMING (54 LEDs,
20mA, VIN = 12V)
FIGURE 10. IL AT 50% PWM DIMMING (54LEDs, 20mA,
VIN = 12V, L = 8.2µH)
FIGURE 11. IL ZOOM IN AT PWM DIMMING ZOOM IN (54 LEDs,
20mA, VIN = 12V, L = 8.2µH)
FIGURE 12. ILED AT 50% PWM DIMMING (54 LEDs, 20mA,
VIN = 12V)
FIGURE 13. LX AT 50% PWM DIMMING (54 LEDs, 20mA,
VIN = 12V)
7
FN6566.0
May 9, 2008
ISL97636A
Typical Performance Curves (Continued)
FIGURE 14. LX ZOOM IN AT 50% DIMMING (54 LEDs, 20mA,
VIN = 12V)
FIGURE 15. RIPPLE VOLTAGE (54 LEDs, VIN = 12V, 20mA
EACH, COUT = 4x4.7µF/50V)
FIGURE 16. RIPPLE VOLTAGE ZOOM IN (54 LEDs, VIN = 12V, 20mA EACH, COUT = 4x4.7µF/50V)
8
FN6566.0
May 9, 2008
ISL97636A
Pinout
VDC
VIN
COMP
FAULT
LX
LX
ISL97636A
(24 LD QFN)
TOP VIEW
24
23
22
21
20
19
17
PGND
FPWM
3
16
OVP
VLEVEL
4
15
IIN0
GND
5
14
IIN1
PWMI/EN
6
13
IIN2
7
8
9
10
11
12
IIN3
2
RSET
GND
IIN4
PGND
IIN5
18
NC
1
NC
GND
Pin Descriptions (I = Input, O = Output, S = Supply)
PIN
NAME
TYPE
DESCRIPTION
1
GND
S
Analog GND
2
GND
S
Analog GND
3
FPWM
-
Not used. Leave floating and connect anything will have no effect on operation
4
VLEVEL
-
Not used. Leave floating and connect anything will have no effect on operation
5
GND
S
Analog GND and LED power return
6
EN/PWMI
I
Dual Functions: Enable Pin and PWM brightness control pin. DO NOT leave EN/PWMI floating. The device needs
40µs for initial power-up Enable, then this pin can be applied with a PWM signal with off time no longer than 28ms.
7, 8
NC
-
No Connect. Can be floating or grounded
9
IIN5
I
Input 5 to current source, FB, and monitoring
10
IIN4
I
Input 4 to current source, FB, and monitoring
11
RSET
I
Resistor connection for setting LED current, (see Equation 1 for calculating the ILEDpeak)
12
IIN3
I
Input 3 to current source, FB, and monitoring
13
IIN2
I
Input 2 to current source, FB, and monitoring
14
IIN1
I
Input 1 to current source, FB, and monitoring
15
IIN0
I
Input 0 to current source, FB, and monitoring
16
OVP
I
Overvoltage protection input
17
PGND
S
Power ground (LX Power return)
18
PGND
S
Power ground (LX Power return)
19
LX
I
Input to boost switch
20
LX
I
Input to boost switch
21
FAULT
O
Fault disconnect switch
22
COMP
O
Boost compensation pin
23
VIN
S
Input voltage for the device and LED power
24
VDC
S
De-couple capacitor for internally generated supply rail. If 2.7V < VBL+ < 5.5V, apply VDC directly with a supply
voltage of 2.7V to 5.5V
9
FN6566.0
May 9, 2008
ISL97636A
Theory of Operation
PWM Boost Converter
The current mode PWM boost converter produces the
minimal voltage needed to enable the LED stack with the
highest forward voltage drop to run at the programmed
current. The ISL97636A employes current mode control
boost architecture that has a fast current sense loop and a
slow voltage feedback loop. Such architecture achieves a
fast transient response that is essential for the notebook
backlight application where the power can be a series of
drained batteries or instantly changed to an AC/DC adapter
without rendering a noticeable visual nuisance. The number
of LEDs that can be driven by ISL97636A depends on the
type of LED chosen in the application. The ISL97636A is
capable of boosting up to 34.5V and typically driving 9 LEDs
in series for each of the 6 channels, enabling a total of 54
pieces of the 3.5V/30mA type of LEDs.
+
-
+
REF
RSET
+
PWM DIMMING
FIGURE 17. SIMPLIFIED CURRENT SOURCE CIRCUIT
Dynamic Headroom Control
Enable and PWMI
The EN/PWMI pin serves dual purposes; it is used as an
enable signal and can be used for PWM input signal for
dimming. If a PWM signal is applied to this pin, the first pulse of
minimum 40µs will be used as an Enable signal. If there is no
signal for longer than 28ms, the device will enter shutdown.
The EN/PWMI pin cannot be floating, thus a 10kΩ pull-down
resistor may need to be added.
Current Matching and Current Accuracy
Each channel of the LED current is regulated by the current
source circuit, as shown in Figure 17.
The LED peak current is set by translating the RSET current
to the output with a scaling factor of 733/RSET. The source
terminals of the current source MOSFETs are designed as
100mV to minimize the power loss. The sources of errors of
the channel-to-channel current matching come from the
op amp’s offset, internal layout and reference and these
parameters are optimized for current matching and absolute
current accuracy. The absolute accuracy is also determined
by the external RSET, and therefore a 1% tolerance resistor
should be used.
The ISL97636A features a proprietary Dynamic Headroom
Control circuit that detects the highest forward voltage string
or effectively the lowest voltage from any of the IIN pins.
When this lowest IIN voltage is lower than the short circuit
threshold, VSC, such voltage will be used as the feedback
signal for the boost regulator. The boost makes the output to
the correct level such that the lowest IIN pin is at the target
headroom voltage. Since all LED stacks are connected to
the same output voltage, the other IIN pins will have a higher
voltage, but the regulated current source circuit on each
channel will ensure that each channel has the same current.
The output voltage will regulate cycle by cycle and it is
always referenced to the highest forward voltage string in the
architecture.
Dimming Controls
The ISL97636A allows two ways of controlling the LED
current, and therefore, the brightness. They are:
1. DC current adjustment
2. PWM chopping of the LED current defined in Step 1.
MAXIMUM DC CURRENT SETTING
The initial brightness should be set by choosing an
appropriate value for RSET. This should be chosen to fix the
maximum possible LED current:
733
I LEDmax = --------------R SET
(EQ. 1)
DC CURRENT ADJUSTMENT
RSET can be a DCP (Digitally Controlled Potentiometer) for
DC current adjustment but minimum resistance should not
be lower than 21kΩ for a maximum of 35mA.
10
FN6566.0
May 9, 2008
ISL97636A
For example, if the maximum required LED current (ILED(max))
is 20mA, rearranging Equation 1 yields Equation 3:
prevents high input current for systems that have only a low
to medium output current requirement.
R SET = 733 ⁄ 0.02 = 36.6kΩ
For systems with no master fault protection FET, the inrush
current will flow towards COUT when VIN is applied and it is
determined by the ramp rate of VIN and the values of COUT
and L.
(EQ. 2)
PWM CURRENT CONTROL
The average LED current of each channel can be controlled by
an external PWMI signal as shown in Equation 3:
I LED ( ave ) = I LED × PWMI
(EQ. 3)
The PWM dimming frequency can be, for example, 20kHz,
but there are a minimum on and off time requirements such
that the dimming will be in the range of 10% to 99.5%. If the
dimming frequency is below 5kHz, the dimming range can
be 1% to 99.5%.
The PWM dimming off time cannot be longer than 28ms or
else the driver will enter shutdown.
5V Low Dropout Regulator
A 5.2V LDO regulator is present at the VDC pin to develop
the necessary low voltage supply which is used by the chips
internal control circuitry. Because VDC is an LDO pin, it
requires a bypass capacitor of 1µF or more for the
regulation. For applications with an input voltage ≤ 5.5V, the
VIN and VDC pins can be connected together. The VDC pin
can be used as a coarse reference with few mA sourcing
capability.
Inrush Control and Soft-start
The ISL97636A has separately built-in independent inrush
control and soft-start functions. The inrush control function is
built around the short circuit protection FET, and is only
available in applications, which include this device. At startup, the fault protection FET is turned on slowly due to a
30µA pull-down current output from the FAULT pin. This
discharges the fault FET's gate-source capacitance, turning
on the FET in a controlled fashion. As this happens, the
output capacitor is charged slowly through the weakly turned
on FET before it becomes fully enhanced. This results in a
low inrush current. This current can be further reduced by
adding a capacitor (in the 1nF to 5nF range) across the gate
source terminals of the FET.
Once the chip detects that the fault protection FET is turned
on hard, it is assumed that inrush is complete. At this point,
the boost regulator will begin to switch and the current in the
inductor will ramp-up. The current in the boost power switch
is monitored and the switching terminated in any cycle
where the current exceeds the current limit. The ISL97636A
includes a soft-start feature where this current limit starts at a
low value (375mA). This is stepped up to the final 3A current
limit in seven further steps of 375mA. These steps will
happen over a 1ms total time, such that after 1ms the final
limit will be reached. This allows the output capacitor to be
charged to the required value at a low current limit and
11
Fault Protection and Monitoring
The ISL97636A features extensive protection functions to
cover all the perceivable failure conditions. The failure mode
of a LED can be either open circuit or as a short. The
behavior of an open circuited LED can additionally take the
form of either infinite resistance or, for some LEDs, a zener
diode, which is integrated into the device in parallel with the
now opened LED.
For basic LEDs (which do not have built-in zener diodes), an
open circuit failure of an LED will only result in the loss of
one channel of LEDs without affecting other channels.
Similarly, a short circuit condition on a channel that results in
that channel being turned off does not affect other channels
unless a similar fault is occurring.
Due to the lag in boost response to any load change at its
output, certain transient events (such as LED current steps
or significant step changes in LED duty cycle) can transiently
look like LED fault modes. The ISL97636A uses feedback
from the LEDs to determine when it is in a stable operating
region and prevents apparent faults during these transient
events from allowing any of the LED stacks to fault out. See
Table 1 for more details.
A fault condition that results in an input current that exceeds
the devices electrical limits will result in a shutdown of all
output channels.
Short Circuit Protection (SCP)
The short circuit detection circuit monitors the voltage on
each channel and disables faulty channels which are
detected above 8V (the action taken is described in Table 1.)
Open Circuit Protection (OCP)
When one of the LEDs becomes open circuit, it can behave
as either an infinite resistance or a gradually increasing finite
resistance. The ISL97636A monitors the current in each
channel such that any string which reaches at least 75% of
the intended output current is considered “good”. Should the
current subsequently fall below 50% of the target the
channel will be considered an “open circuit”. Furthermore,
should the boost output of the ISL97636A reach the OVP
limit or should the lower over-temperature threshold be
reached, all channels which are not “good” will immediately
be considered as “open circuit”. Detection of an “open
circuit” channel will result in a time-out before disabling of
the affected channel. This time-out is sped up when the
device is above the lower over-temperature threshold in an
attempt to prevent the upper over-temperature trip point from
being reached.
FN6566.0
May 9, 2008
ISL97636A
Some users employ some special types of LEDs that have
zener diode structure in parallel with the LED for ESD
enhancement and enabling open circuit operation. When
this type of LED is open circuited, the effect is as if the LED
forward voltage has increased but no lighting. Any affected
string will not be disabled, unless the failure results in the
boost OVP limit being reached, allowing all other LEDs in the
string to remain functional. Care should be taken in this case
that the boost OVP limit and SCP limit are set properly, so as
to make sure that multiple failures on one string do not
cause all other good channels to be faulted out. This is due
to the increased forward voltage of the faulty channel making
all other channels look as if they have LED shorts. See
Table 1 for details regarding responses to fault conditions.
Overvoltage Protection (OVP)
The integrated OVP circuit monitors the output voltage and
keeps the voltage at a safe level. The OVP threshold is set
as:
OVP = 1.21V × ( R UPPER + R LOWER ) ⁄ R LOWER
(EQ. 4)
These resistors should be large to minimize the power loss.
For example, a 1MΩ RUPPER and 39kΩ RLOWER sets OVP
to 32.2V. Large OVP resistors also allow COUT discharges
slowly during the PWM off time.
Undervoltage Lockout
If the input voltage falls below the UVLO level of 2.45V, the
device will stop switching and reset. Operation will restart
when the voltage comes back into the operating range.
Input Overcurrent Protection
During normal switching operation, the current through the
internal boost power FET is monitored. If the current
exceeds the current limit, the internal switch will be turned
12
off. This monitoring happens on a cycle-by-cycle basis in a
self protecting way.
Additionally, the ISL97636A monitors the voltage at the LX
and OVP pins. At start-up, a fixed current is injected out of
the LX pins and into the output capacitor. The device will not
start-up unless the voltage at LX exceeds 1.2V. Furthermore,
should the voltage at LX not rise above this threshold during
any subsequent period where the power FET is not switched
on, it will immediately disable the input protection FET. The
OVP pin is also monitored such that if it rises above and
subsequently falls below 20% of the target OVP level, the
input protection FET will also be switched off.
Over-Temperature Protection (OTP)
The ISL97636A includes two over-temperature thresholds. The
lower threshold is set to +130°C. When this threshold is
reached, any channel which is outputting current at a level
significantly below the regulation target will be treated as “open
circuit” and disabled after a time-out period. This time-out
period is also reduced to 800µs when it is above the lower
threshold. The intention of the lower threshold is to allow bad
channels to be isolated and disabled before they cause enough
power dissipation (as a result of other channels having large
voltages across them) to hit the upper temperature threshold.
The upper threshold is set to +150°C. Each time this is
reached, the boost will stop switching and the output current
sources will be switched off. Once the device has cooled to
approximately +100°C, the device will restart with the DC
LED current level reduced to 77% of the initial setting. If the
dissipation problem persists, subsequent hitting of the limit
will cause identical behavior, with the current reduced in
steps to 53% and finally 30%. Unless disabled via the EN
pin, the device stays in an active state throughout.
For the extensive fault protection conditions, please refer to
Figure 18 and Table 1 for details.
FN6566.0
May 9, 2008
ISL97636A
LX
VIN
VOUT
LX
FAULT
O/P
SHORT
DRIVER
OVP
IMAX
FET
DRIVER
LOGIC
ILIMIT
IIN0
VSC
IIN5
THRM
SHDN
REF
OTP
T2
TEMP
SENSOR
T1
FAULT
DETECT
LOGIC
VSET
Q0 VSET
PWM/OC0/SC0
Q5
PWM/OC5/SC5
PWM
GENERATOR
FIGURE 18. SIMPLIFIED FAULT PROTECTIONS
TABLE 1. PROTECTIONS TABLE
CASE
FAILURE MODE
DETECTION
MODE
FAILED CHANNEL ACTION
GOOD CHANNELS ACTION
VOUT
REGULATED BY
1
CH0 Short Circuit
CH0 ON and burns power
Upper
Over-Temperature
Protection limit
(OTP) not
triggered and
VIIN0 < VSC
CH1 through CH5 Normal
Highest VF of CH1
through CH5
2
CH0 Short Circuit
CH0 goes off until chip cooled and
Upper OTP
triggered but VIN0 then comes back on with current
reduced to 76%. Further OTP
< VSC
triggers result in reduction to 53%,
then 30%.
Same as CH0
Highest VF of CH1
through CH5
3
CH0 Short Circuit
Upper OTP not
triggered but
VIIN0 > VSC
CH1 through CH5 Normal
CH0 doubled after 6ms time-out.
Time-out reduced to 420µs if above
lower OTP limit
Highest VF of CH1
through CH5
4
CH0 Open Circuit
with infinite
resistance
Upper OTP not
triggered and
VIIN0 < VSC
VOUT will ramp to OVP. CH0 will
time-out after 6ms (800µs if above
lower OTP limit) and switch off.
VOUT will drop to normal level.
CH1 through CH5 Normal
Highest VF of CH1
through CH5
5
CH0 LED Open
Circuit but has
paralleled Zener
Upper OTP not
triggered and
VIIN0 < VSC
CH0 remains ON and has highest
VF, thus VOUT increases
CH1 through CH5 ON, Q1 through
Q5 burn power
VF of CH0
13
FN6566.0
May 9, 2008
ISL97636A
TABLE 1. PROTECTIONS TABLE (Continued)
CASE
FAILURE MODE
DETECTION
MODE
FAILED CHANNEL ACTION
GOOD CHANNELS ACTION
VOUT
REGULATED BY
6
CH0 LED Open
Circuit but has
paralleled Zener
Upper OTP
triggered but
VIIN0 < VSC
CH0 goes off until chip cooled and
then comes back on with current
reduced to 76%. Further OTP
triggers result in reduction to 53%,
then 30%.
Same as CH0
VF of CH0
7
CH0 LED Open
Circuit but has
paralleled Zener
Upper OTP not
triggered but
VIIN0 > VSC
CH0 OFF
CH1 through CH5 Normal
Highest VF of CH1
through CH5
CH0 remains ON and has highest
Upper OTP not
triggered but VIINx VF, thus VOUT increases.
> VSC
VF of CH0
VOUT increases then CH-X
switches OFF. This is an unwanted
shut off and the effect can be
minimized by setting OVP at an
appropriate level.
8
Any channel at below 50% of the target current will fault out after 400µs.
Channel-to-Channel Lower OTP
ΔVF too high
triggered but VIINx Remaining channels driven with normal current.
< VSC
Highest VF of CH0
through CH5
9
All channels switched off until chip cooled and then comes back on with Highest VF of CH0
Channel-to-Channel Upper OTP
ΔVF too high
triggered but VIINx current reduced to 76%. Further OTP triggers result in reduction to 53%, through CH5
then 30%.
< VSC
10
Output LED stack
voltage too high
VOUT > VOVP
Driven with normal current. Any channel that is below 50% of the target
current will time-out after 6ms.
11
VOUT/LX shorted to LX current and
GND
timing are
monitored.
Fault switch disabled and system shutdown until fault goes away, VOUT
is checked at start-up with a low current from LX to check for presence of
short before the fault switch is enabled.
Highest VF of CH0
through CH5
OVP pin
monitored for
excursions below
20% of OVP
threshold
Input Capacitor
Components Selections
According to the inductor Voltage-Second Balance principle,
the change of inductor current during the switching regulator
On time is equal to the change of inductor current during the
switching regulator Off time. Since the voltage across an
inductor is:
V L = L × ΔI L ⁄ Δt
(EQ. 5)
and ΔIL @ On = ΔIL @ Off, therefore:
( V I – 0 ) ⁄ L × D × tS = ( VO – VD – VI ) ⁄ L × ( 1 – D ) × tS
(EQ. 6)
where D is the switching duty cycle defined by the turn-on
time over the switching period. VD is Schottky diode forward
voltage that can be neglected for approximation.
Rearranging the terms without accounting for VD gives the
boost ratio and duty cycle respectively as:
VO ⁄ VI = 1 ⁄ ( 1 – D )
(EQ. 7)
D = ( VO – VI ) ⁄ VO
(EQ. 8)
14
Switching regulators require input capacitors to deliver peak
charging current and to reduce the impedance of the input
supply. This reduces interaction between the regulator and
input supply, improving system stability. The high switching
frequency of the loop causes almost all ripple current to flow
in the input capacitor, which must be rated accordingly.
A capacitor with low internal series resistance should be
chosen to minimize heating effects and improve system
efficiency, such as X5R or X7R ceramic capacitors, which
offer small size and a lower value of temperature and voltage
coefficient compared to other ceramic capacitors.
In boost mode, input current flows continuously into the
inductor, with an AC ripple component proportional to the
rate of inductor charging only and smaller value input
capacitors may be used. It is recommended that an input
capacitor of at least 10µF be used. Ensure the voltage rating
of the input capacitor is suitable to handle the full supply
range.
FN6566.0
May 9, 2008
ISL97636A
Inductor
The selection of the inductor should be based on its
maximum current (ISAT) characteristics, power dissipation
(DCR), EMI susceptibility (shielded vs unshielded), and size.
Inductor type and value influence many key parameters,
including ripple current, current limit, efficiency, transient
performance and stability.
Its maximum current capability must be adequate to handle
the peak current at the worst case condition. If an inductor
core is chosen with too low a current rating, saturation in the
core will cause the effective inductor value to fall, leading to
an increase in peak to average current level, poor efficiency
and overheating in the core. The series resistance, DCR,
within the inductor causes conduction loss and heat
dissipation. A shielded inductor is usually more suitable for
EMI susceptible applications, such as LED backlighting.
The peak current can be derived from the fact that the
voltage across the inductor during the Off period can be
shown as:
IL peak = ( V O × I O ) ⁄ ( 85% × V I ) + 1 ⁄ 2 [ V I × ( V O – V I ) ⁄ ( L × V O × f S ) ]
(EQ. 9)
The choice of 85% is just an average term for the efficiency
approximation. The first term is average current that is
inversely proportional to the input voltage. The second term
is inductor current change that is inversely proportional to L
and fS. As a result, for a given switching frequency and
minimum input voltage the system operates, the inductor
ISAT must be chosen carefully. At a given inductor size,
usually the larger the inductance, the higher the series
resistance because of the extra winding of the coil. Thus, the
higher the inductance, the lower the peak current capability.
The ISL97636A current limit may also have to be taken into
account.
backlight applications due to their cost, form factor, and low
ESR.
A larger output capacitor will also ease the driver response
during PWM dimming Off period due to the longer sample
and hold effect of the output drooping. The driver does not
need to boost harder in the next On period that minimizes
transient current. The output capacitor is also needed for
compensation, and in general, 2x4.7µF/50V ceramic
capacitors are suitable for the notebook display backlight
applications.
Schottky Diode
A high speed rectifier diode is necessary to prevent
excessive voltage overshoot, especially in the boost
configuration. Low forward voltage and reverse leakage
current will minimize losses, making Schottky diodes the
preferred choice. Although the Schottky diode turns on only
during the boost switch Off period, it carries the same peak
current as the inductor’s, and therefore, a suitable current
rated Schottky diode must be used.
Applications
High Current Applications
Each channel of the ISL97636A can support up to 35mA.
For applications that need higher current, multiple channels
can be grouped to achieve the desirable current. For
example, the cathode of the last LED can be connected to
IIN0 to IIN2; this configuration can be treated as a single
string with 105mA current driving capability.
VOUT
Output Capacitors
The output capacitor acts to smooth the output voltage and
supplies load current directly during the conduction phase of
the power switch. Output ripple voltage consists of the
discharge of the output capacitor for ILPEAK during FET On
and the voltage drop due to flowing through the ESR of the
output capacitor. The ripple voltage can be shown as:
ΔV CO = ( I O ⁄ C O × D ⁄ f S ) + ( ( I O × ESR )
(EQ. 10)
The conservation of charge principle in Equation 8 also
brings up a fact that during the boost switch Off period, the
output capacitor is charged with the inductor ripple current
minus a relatively small output current in boost topology. As
a result, the user needs to select an output capacitor with
low ESD and with a enough input ripple current capability.
Output Ripple
ΔVCo can be reduced by increasing CO or fS, or using small
ESR capacitors. In general, ceramic capacitors are the best
choice for output capacitors in small to medium sized LCD
15
IIN0
IIN1
IIN2
FIGURE 19. GROUPING MULTIPLE CHANNELS FOR HIGH
CURRENT APPLICATIONS
Compensation
The ISL97636A has two main elements in the system; the
Current Mode Boost Regulator and the op amp based
multi-channel current sources. The ISL97636A incorporates
a transconductance amplifier in its feedback path to allow
the user some levels of adjustment on the transient
response and better regulation. The ISL97636A uses current
mode control architecture, which has a fast current sense
loop and a slow voltage feedback loop. The fast current
feedback loop does not require any compensation. The slow
voltage loop must be compensated for stable operation. The
FN6566.0
May 9, 2008
ISL97636A
compensation network is a series Rc, Cc1 network from
COMP pin to ground and an optional Cc2 capacitor
connected to the COMP pin. The Rc sets the high frequency
integrator gain for fast transient response and the Cc1 sets
the integrator zero to ensure loop stability. For most
applications, Rc is in the range of 200Ω to 3kΩ and Cc1 is in
the range of 27nF to 37nF. Depending upon the PCB layout,
a Cc2, in range of 100nF, may be needed to create a pole to
cancel the output capacitor ESR’s zero effect for stability.
The ISL97636A evaluation board is configured with Rc1 of
500Ω, Cc1 of 33nF, and Cc2 of 0, which achieves stability. In
the actual applications, these values may need to be tuned
empirically but the recommended values are usually a good
starting point.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
16
FN6566.0
May 9, 2008
VIN
Q1
4
C1
10µ/25V
C2
0.1µ/25V
3
D1 D1 : SS15 - Vishay Schottky Diode, 5
L1
1
2
5
6
8.2µH
C4
10µ/25V
C6
4.7µ/50V
SS15
C7
4.7µ/50V
FDMA530PZ
2
GND
3
FPWM
19
R3
1M
LX
PGND
17
OVP
16
14
6
PWMI/EN
IIN2
13
9
7
LED19
LED28
LED37
LED46
LED2
LED11
LED20
LED29
LED38
LED47
OVP
LED3
LED12
LED21
LED30
LED39
LED48
LED4
LED13
LED22
LED31
LED40
LED49
LED5
LED14
LED23
LED32
LED41
LED50
LED6
LED15
LED24
LED33
LED42
LED51
LED7
LED16
LED25
LED34
LED43
LED52
LED8
LED17
LED26
LED35
LED44
LED53
LED9
LED18
LED27
LED36
LED45
LED54
R4
39k
R2
36.6k
FIGURE 20. TYPICAL APPLICATION CIRCUIT
ISL97636A
12 IIN3
IIN1
11 RSET
GND
10 IIN4
5
IIN5
IIN0
NC
PWMO
NC
4
15
NOTES:
FOR 2 LAYERS BOARD, LAYOUT
PGND (NOISY GROUND) ON TOP
LAYER AND AGND (QUIET GROUND)
ON BOTTOM LAYER. TIE PGND AND
AGND ONLY AT ONE POINT BY DOING
THIS: BRIDGE U1 PGND (PINS 18 AND 19)
AND AGND (PIN 5) TO THE PACKAGE
THERMAL PAD. PUT MULTIPLE VIAS ON THE
THERMAL PAD THAT CONNECTS TO THE
BOTTOM SIDE AGND.
LED10
18
PGND
ISL97636A
U1
LED1
LX
20
21
23
C20
FAULT
GND
COMP
1
8
17
PWMI/EN
VDC
C11
1µ/10V
VIN
24
C12
0.1µ/10V
22
C10
33n
R7
500
FN6566.0
May 9, 2008
ISL97636A
Package Outline Drawing
L24.4x4D
24 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 2, 10/06
4X 2.5
4.00
A
20X 0.50
B
PIN 1
INDEX AREA
PIN #1 CORNER
(C 0 . 25)
24
19
1
4.00
18
2 . 50 ± 0 . 15
13
0.15
(4X)
12
7
0.10 M C A B
0 . 07
24X 0 . 23 +- 0
. 05 4
24X 0 . 4 ± 0 . 1
TOP VIEW
BOTTOM VIEW
SEE DETAIL "X"
0.10 C
C
0 . 90 ± 0 . 1
BASE PLANE
( 3 . 8 TYP )
SEATING PLANE
0.08 C
SIDE VIEW
(
2 . 50 )
( 20X 0 . 5 )
C
0 . 2 REF
5
( 24X 0 . 25 )
0 . 00 MIN.
0 . 05 MAX.
( 24X 0 . 6 )
DETAIL "X"
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1. Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3. Unless otherwise specified, tolerance : Decimal ± 0.05
4. Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5. Tiebar shown (if present) is a non-functional feature.
6. The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
18
FN6566.0
May 9, 2008