User's Manual

rBOX510-6COM(ATEX&C1D2)
Robust Din-rail Fanless Embedded System
User’s Manual
Reversion History
Version
Updated Date
A1
2015/Jul./ 30
ii
Updated Reason
Initial Release
Updated page
NO
Disclaimers
This manual has been carefully checked and believed to contain accurate
information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of
patents or any third party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the
accuracy, completeness or usefulness of any information in this document. Axiomtek
does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any
time without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
Copyright 2015 Axiomtek Co., Ltd.
All Rights Reserved
October 2015, Version A1
Printed in Taiwan
iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1.
The rBOX510-6COM(ATEX&C1D2) does not come equipped with an operating
system. An operating system must be loaded first before installing any software
into the computer.
2.
Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components
in any static-shielded devices. Most electronic components are sensitive to
static electrical charge.
3.
Disconnect the power cord from the rBOX510-6COM(ATEX&C1D2) before
making any installation. Be sure both the system and the external devices are
turned OFF. Sudden surge of power could ruin sensitive components. Make
sure the rBOX510-6COM(ATEX&C1D2) is properly grounded.
4.
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
5.
Turn OFF the system power before cleaning. Clean the system using a cloth
only. Do not spray any liquid cleaner directly onto the screen.
6.
Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -45℃ or above 85℃. It may damage the equipment.
7.
Start the equipment maintenance and repair after turn OFF the system power
for at least 15 miniutes.
8.
Replaceable batteries
"CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type.
Dispose of Used Batteries According to the Instructions."
9.
Restricted Access Location
"Equipment intended for installation in Restricted Access Location" or
equivalent. (Instruction)
10. Power source requirement
"This product is intended to be supplied by a UL Listed Power sourcce
marked with "LPS", "Limited Power Source" or "Class 2" and output rated
12-48 Vdc, 1.63-0.45 A min." or equivalent statement provided in
operating manual.
11. Do not open the system ’s back cover. If opening the cover for maintenance is a
must, only a trained technician is allowed to do so. Integrated circuits on
computer boards are sensitive to static electricity. To avoid damaging chips
from electrostatic discharge, observe the following precautions:
iv

Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This will help to discharge any
static electricity on your body.

When handling boards and components, wear a wrist -grounding strap,
available from most electronic component stores .
Classification
1.
Degree of production against electric shock: not classified
2.
Degree of protection against the ingress of water: IP30
3.
Equipment not suitable for use in the presence of a flammable anesthetic
mixture with air or with oxygen or nitrous oxide.
4.
Mode of operation: Continuous
5.
Type of protection against electric shock: Class I equipment
General Cleaning Tips
You may need the following precautions before you begin to clean the c omputer.
When you clean any single part or component for the com puter, please read and
understand the details below fully.
When you need to clean the device, please rub it with a pi ece of dry cloth.
1.
Be cautious of the tiny removable components when you us e a vacuum cleaner
to absorb the dirt on the floor.
2.
Turn the system off before you start to clean up the component or computer.
3.
Never drop the components inside the computer or get circuit board damp or
wet.
4.
Be cautious of all kinds of cleaning solvents or chemicals when you use it for
the sake of cleaning. Some individuals may be allergic to the ingredients.
5.
Try not to put any food, drink or cigarette around the computer.
v
Cleaning Tools
Although many companies have created products to help improve th e process of
cleaning your computer and peripherals users can also use household items to
clean their computers and peripherals. Below is a listing of items you may need or
want to use while cleaning your computer or computer peripherals.
Keep in mind that some components in your computer may only be able to be
cleaned using a product designed for cleaning that component, if this is the case it
will be mentioned in the cleaning.

Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, we still recommend you
to rub it with a piece of cloth.

Water or rubbing alcohol: You may moisten a piece of cloth a bit with some
water or rubbing alcohol and rub it on the computer. Unknown solvents may be
harmful to the plastics parts.

Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other
particles out of a computer can be one of the best methods of cleaning a
computer. Over time these items can restrict the airfl ow in a computer and
cause circuitry to corrode.

Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are
excellent tools for wiping hard to reach areas in your keyboard, mouse, and
other locations.

Foam swabs: Whenever possible it is better to use lint free swabs such as
foam swabs.
Note: We strongly recommended that you should shut down the system before you start to
clean any single components.
Please follow the steps below:
vi
1.
Close all application programs
2.
Close operating software
3.
Turn off power
4.
Remove all device
5.
Pull out power cable
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond repair, we strongly
recommended that you should inform your Axiomtek distributor as soon as possible
for the suitable solution. For the computers that are no longer useful or no longer
working well, please contact your Axiomtek distributor for recycling and we will
make the proper arrangement.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, VGA are trademarks of International Business Machines Corporation.
®
Intel is registered trademarks of Intel Corporation.
Windows 7, Windows 8 and QuickBASIC are trademarks of Microsoft Corporation.
UMC is a trademark of United Microelectronics Corporation. Other brand names and
trademarks are the properties and regis tered brands of their respective owners.
vii
Table of Contents
Reversion History ................................................................................................... ii
Safety Precautions ................................................................................................. iv
Classification ........................................................................................................... v
General Cleaning Tips ............................................................................................ v
Scrap Computer Recycling .................................................................................. vii
CHAPTER 1 INTRODUCTION ........................................................................ 1
1.1
1.2
1.2.1
1.2.2
1.2.3
1.2.4
1.2.5
1.2.6
1.2.7
1.2.8
1.2.9
1.2.10
1.2.11
1.2.12
1.2.13
1.2.14
1.2.15
1.2.16
1.2.17
1.2.18
1.2.19
1.3
1.3.1
1.3.2
1.4
1.5
General Description ............................................................................ 1
System Specifications ........................................................................ 2
CPU .................................................................................................................... 2
BIOS ................................................................................................................... 2
System Memory ................................................................................................ 2
Display ............................................................................................................... 2
Ethernet Ports ................................................................................................... 2
Storages............................................................................................................. 2
USB .................................................................................................................... 3
COM .................................................................................................................... 3
Power ................................................................................................................. 4
WatchDog Timer (WDT).................................................................................... 7
Digital I/O Connector and Pin Definition ........................................................ 7
Ethernet Ports ................................................................................................. 12
System LED ..................................................................................................... 13
Operation Temperature .................................................................................. 14
Storage Temperature ...................................................................................... 14
Humidity........................................................................................................... 14
Weight .............................................................................................................. 14
Dimensions...................................................................................................... 14
System I/O Outlets .......................................................................................... 14
Non-sparking low power equipment ................................................ 15
General information for use ........................................................................... 15
Field Installation ............................................................................................. 17
Dimensions ....................................................................................... 18
I/O Outlets.......................................................................................... 19
CHAPTER 2 HARDWARE INSTALLATION ................................................. 21
2.1
2.2
Installing Din-rail Mounting .............................................................. 21
Installing Wall Mounting (optional) .................................................. 23
CHAPTER 3 AMI UEFI BIOS UTILITY.......................................................... 25
3.1
3.2
3.3
3.4
3.5
3.6
3.7
Entering Setup .................................................................................. 25
The Main Menu .................................................................................. 26
Advanced Features ........................................................................... 27
Chipset Feature ................................................................................. 36
Security.............................................................................................. 37
Boot Type .......................................................................................... 39
Save & Exit ........................................................................................ 42
APPENDIX A WATCHDOG TIMER .............................................................. 45
About Watchdog Timer .................................................................................... 45
How to Use Watchdog Timer ........................................................................... 45
APPENDIX B DIO Command ....................................................................... 47
How to Use DIO Registers ................................................................................ 47
viii
rBOX510-6COM(ATEX&C1D2) User’s Manual
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the rBOX510-6COM
(ATEX&C1D2). The Chapter 1 includes the following sections:

General Description
System Specification
Dimensions
I/O Outlets



1.1
General Description
rBOX510-6COM(ATEX&C1D2) Din-rail fanless embedded system is suitable for
communications control and for protocol converter applications in critical
environments. Built for rugged work environments, rBOX510-6COM(ATEX&C1D2)
®
features an extra low power consumption Intel ATOM ™ E3827 (1.75GHz)
processors supporting industrial temperature range of -40℃ to +70℃. Its front
accessible I/O cabling is very convenient for wiring and maintenance. rBOX5106COM(ATEX&C1D2) offers a VGA output, making it particularly well-suited for
communication control, SCADA and industrial automation. Its compact size with Din rail mounting allows for easy installation into control cabinet. Pre -installed with
®
Linux, W indows
7 embedded and W indows 8 embedded, rBOX5106COM(ATEX&C1D2) provides programmers with a friendly environment for
developing application software at a lower cost.
rBOX510-6COM(ATEX&C1D2) is robust industrial-grade hardware design and
adopts the advanced cooling system , besides, supporting the CompactFlash™ and
SATA SSD (Solid State Drive), which makes it especially suitable for field control &
monitoring system solution for following markets:
Utility Industries (Water; Energy; Chemical Plant; Mining…)
Public Transportation Industries (Traffic/ Highway Control; Train/Bus Control…)
Homeland Security (Weather Monitoring/Alarm System…)

Features


Fanless design
Wide temperature operation of -40℃ - +70℃

Supports 2 10/100/1000 Base-T Ethernets with Magnetic Isolated Protection

4 isolated RS-232/422/485 COM Ports and 2 RS-232/422/485 COM Ports

1 isolated DIO (8-IN/ 8-OUT)

Support one 2.5” SATA SSD (Solid State Drive) and one CompactFlash™

Wide range 12–48V DC-in with terminal block

Din-rail mounting

Wall mounting (optional)

Passed Heavy Industrial CE, FCC Part 18 and UL testing

Passed ATEX & C1D2 Anti-explosive Certification
Introduction
1
rBOX510-6COM(ATEX&C1D2) User’s Manual

Embedded O.S. Supported
®
®
rBOX510-6COM(ATEX&C1D2) not only supports W indows 7 and W indows 8,
®
®
but also supports embedded OS, such as W indows 7 embedded, W indows 8
embedded and Linux package support. For storage device, rBOX5106COM(ATEX&C1D2) supports one SATA SSD (Solid State Drive) and one type
II CompactFlash ™ socket.
1.2
System Specifications
1.2.1

®
Onboard Intel ATOM™ E3827 (1.75 GHz) processor.
1.2.2

CPU
BIOS
AMI (American Megatrends Inc.) UEFI (Unified Extensible Firmware Interface)
BIOS.
1.2.3
System Memory

Memory down solution w/extended temperature memory chip

Memory size 4GB onboard
1.2.4

A slim type 15-pin D-Sub connector as VGA connector.
1.2.5

Display
Ethernet Ports
LAN 1 and LAN 2
The board has dual RJ-45 connectors, support 10/100/1000Mbps with 1.5KV
magnetic isolated protection.

Support PXE boot and LAN wake-up
1.2.6
Storages

1 x 2.5” SATA SSD (Solid State Drive ) (default)

1 x CompactFlash TypeII socket
Note: Connecting the SATA+Power SSD cable with Solid State Drive, and the
SATA+Power SSD cable needs to be glued by using “LDC737” silicone when
connect to the board connector.
2
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual
1.2.7
USB

1 x USB2.0 & 1 x USB3.0

It is always plugged-in the USB housing cover (pls refer below picture),
excepting equipment maintenance and repair situation.

It is used for maintenance and repair only, ex: accesse data by pluggin gin USB
flash, or check data & remive wrong data by using USB type of keyboard/mouse.

With power distribution control and over current protection

USB Pin Define
Pin
Signal USB 2.0
Pin
Signal USB 3.0
1
VCC
1
VCC
2
D-
2
D-
3
D+
3
D+
4
GND
4
GND
-
-
5
SSRX-
-
-
6
SSRX-
-
-
7
GND
-
-
8
SSTX-
-
-
9
SSTX+
1.2.8

USB2.0
USB 3.0
COM
COM1~COM2 support RS232/RS422/RS485 which can be selected by BIOS.
COM3~COM6 support RS232/RS422/RS485 which can be selected by BIOS with
Isolation 2KV protection.

Supports Auto Flow Control in RS485 mode.
COM1~2
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
--
4
DTR
RX-
--
5
GND
GND
GND
6
DSR
--
--
7
RTS
--
--
8
CTS
--
--
9
RI
--
--
Introduction
3
rBOX510-6COM(ATEX&C1D2) User’s Manual
COM3~6
Pin
RS-232
RS-422
RS-485
1,6
RXD
TX+
Data+
2,7
CTS
TX-
Data-
3,8
TXD
RX+
--
4,9
RTS
RX-
--
5,10
1.2.9

ISO_GND
ISO_GND
ISO_GND
Power
Pin
Signal
1
Alarm+
2
Alarm-
3
Power Fail
4
Shield Ground
5
GND
6
PWR
PF pin must connect to external the power fail of UPS, so can normal shutdown
when being abnormal power loss.
LVCMOS 3.3 Level, VIL: 0.8V, VIH: 2.0~3.6,system internal pull up.

The relay default function will be enabled when the system cannot normal boot

One wide-range 12 - 48V DC power input with terminal block.

OVP, UVP and Reverse protection.
4
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual

Relay output
Below is a very simple application for remote notice
use relay and lamp.
a)
Normal
b)
W arning
Introduction
5
rBOX510-6COM(ATEX&C1D2) User’s Manual
c)
6
Relay wiring of rBox
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual
1.2.10
WatchDog Timer (WDT)

One step is 1sec, 255 levels

One step is 1sec/1min, 255 levels.
1.2.11
Digital I/O Connector and Pin Definition

8bit DI and 8bit DO

3KV optical isolation

DIO Design Sepcification
Digital Input
Input Channels
8,source type
Input Voltage
0 to 30VDC Input
Digital Input Levels for
Dry Contacts
Logic level 0:Close to GND.
Digital Input Levels for
Wet Contacts
Logic level 0:+10V to +24V (DI To XIN_COM-).
Logic level 1:Open
Logic level 1:+3V max.
Digital Output
Output Channels
8,sink type
Output Current
Max. 200 mA per channel, current sink type
External voltage
10 to 30VDC , open collector to 30V
Introduction
7
rBOX510-6COM(ATEX&C1D2) User’s Manual

Remark
Signal Name
Meaning
COM+
Plus common for Input/ Output Group
COM-
Minus common for Input/Output Group
DIN0~7
Input Group
DOUT0~7
Output Group

8
DIO 8 in/out of TB20 Female
Pin
Function
Pin
Function
1
COM+
11
COM+
2
DI0
12
DO0
3
DI1
13
DO1
4
DI2
14
DO2
5
DI3
15
DO3
6
DI4
16
DO4
7
DI5
17
DO5
8
DI6
18
DO6
9
DI7
19
DO7
10
COM-
20
COM-
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual
SMBus Address & GPIO Pin Define

SMBus Address : 0b0100100X

GPIO schematic PIN define
PIN4
 DI0
PIN13  DO0
PIN5
 DI1
PIN14  DO1
PIN6
 DI2
PIN15  DO2
PIN7
 DI3
PIN16  DO3
PIN8
 DI4
PIN17  DO4
PIN9
 DI5
PIN18  DO5
PIN10  DI6
PIN19  DO6
PIN11  DI7
PIN20  DO7
SMBus to GPIO Schematic
Introduction
9
rBOX510-6COM(ATEX&C1D2) User’s Manual
DIO operation schematic diagram
Reference 1.
Reference 2.
10
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual
Reference 3
Digital Input Wiring
Reference 4
Digital Output Wiring
Introduction
11
rBOX510-6COM(ATEX&C1D2) User’s Manual
1.2.12

Ethernet Ports
LAN 1 and LAN 2
The board has dual RJ-45 ethernet connector which using Intel I210-IT ethernet
controllers, support 1000/100/10-Base transmit rate and with 1.5KV magnetic
isolated protection.
Pin
Signal
L1
MDI0+
L2
MDI0-
L3
MDI1+
L4
MDI1-
L5
MDI2+
L6
MDI2-
L7
MDI3+
L8
MDI3-
A
Active LED
B
Speed LED
(Yellow)
1000-Base-T (Amber)
12
100-Base-T
(Green)
10-Base-T
(Dark)
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual
1.2.13

System LED
There are showed the LED’s indicators and functional descriptions.
LED Name
PWR
Description
Indicate the Power status.
LED will be on for green color when the power DC input is
acceptable.
LED will be on for red color when the power DC input isn’t
acceptable or power fail event.
The LED for ACT can help user’s to judge BIOS finish or not
and the OS can normal work or not.
-
ACT
-
LED will ON for red color when the power DC input is system
active
LED will flash for red color when the BIOS start
LED will ON for green color when enter OS status.
LED will flash for green color when the storage is
accessed.
LED always ON without any flash for a long time, the OS
is possible crashed.
LED is off when system shutdown status
Color
Green
Red
Green
Red
COM TX1
When COM1 transmit data the LED will on.
Green
COM RX1
When COM1 receive data the LED will on.
Yellow
COM TX2
When COM2 transmit data the LED will on.
Green
COM RX2
When COM2 receive data the LED will on.
Yellow
COM TX3
When COM3 transmit data the LED will on.
Green
COM RX3
When COM3 receive data the LED will on.
Yellow
COM TX4
When COM4 transmit data the LED will on.
Green
COM RX4
When COM4 receive data the LED will on.
Yellow
COM TX5
When COM5 transmit data the LED will on.
Green
COM RX5
When COM5 receive data the LED will on.
Yellow
COM TX6
When COM6 transmit data the LED will on.
Green
COM RX6
When COM6 receive data the LED will on.
Yellow
Introduction
13
rBOX510-6COM(ATEX&C1D2) User’s Manual
1.2.14

-40℃ ~ +70℃
1.2.15

Dimensions
85.6mm(3.37”) (W) x110mm(4.33”) (D) x155mm(6.10”) (H)
1.2.19

Weight
1.8kg
1.2.18

Humidity
5% ~ 95% (non-condensation)
1.2.17

Storage Temperature
-45℃ ~ +85℃
1.2.16

Operation Temperature
System I/O Outlets
Two DB9 connectors support RS232/RS422/RS485 (COM1/2)
Four isolated Terminal Block connectors support RS232/RS422/RS485 (COM3~COM6)

One 15-pin D-Sub female connector for VGA.

Two 10/100/1000Mbps RJ-45 with 1.5KV magnetic isolated protection.

One isolated DIO (8-IN/8-OUT)

One USB 2.0 connector & one USB 3.0 connector

One DC Power Input with terminal block.

One CompactFlash TypeII socket
14
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual
1.3
Non-sparking low power equipment
The Robust Din-rail Fanless Embedded System rBOX510-6COM(ATEX&C1D2) is
designed according to EN 60079-0:2012+A11:2013 and EN 60079-15:2010 will be used in
zone 2 and Class I Division 2.
1.3.1
General information for use
Types of protection:

rBOX510-6COM(ATEX&C1D2) is designed with type of protection "nA and nC".

DEMKO 15 ATEX 1516X marking:
Div. 2 Groups ABCD T4

Ambient temperature:-40℃~+70℃

The devices are for use in an area of not more than pollution degree 2 in accordance
with EN/IEC 60664-1.

All of fuses shall be soldered in place,and the fuses are non-interchangeable.

The devices are to be installed in an ATEX Certified IP54 enclosure and accessible only
by the use of a tool.
II 3 G Ex nA nC IIC T4 Gc and
Class I
( WARNING - EXPLOSION HAZARD – Do not disconnect equipment unless power has
been removed or the area is known to be non-hazardous. )

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or nonhazardous locations only.
( WARNING - EXPLOSION HAZARD – Substitution of any components may impair
suitability for Class I, Division 2. )

Provision shall be made to prevent the rated voltage being exceeded by the transient
disturbances of more than 140% of the peak rated voltage.

After the Robust Din-rail Fanless Embedded System is mounted and fixed, the customer
will make the whole system grounded, and the ground wire needs to meet the
requirement of EN60079-0, besides, the cross-section area of the ground wire is at least
4mm².
Introduction
15
rBOX510-6COM(ATEX&C1D2) User’s Manual
The I/O ports of non-sparking equipment will be possible connected instruments or
equipments as below examples:

Two DB9 connectors support RS232/RS422/RS485 (COM1/2)
Four isolated Terminal Block connectors support RS232/RS422/RS485 (COM3~COM6)
It will be possibled linked the temperature sensor, wet sensor, meters.

Two Isolated 10/100/1000Mbps Ethernet
It will be possible connected the wired network (HiNet/ NiLink/ Internet)

One Isolated DIO (8-IN/8-OUT) port with Magnetic Isolation Protectio
It will be possible linked digital electronic power lemter.

Two USB
It is always plugged-in the USB housing cover (pls refer below picture), excepting
equipment maintenance and repair situation.
It is used for maintenance and repair only, ex: accesse data by plugging in USB flash, or
check data & remove wrong data by using USB type of keyboard/mouse.

VGA
It will be possible linked the monitoring and management equipme nt.
WARNING – EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE SEALING
PROPERTIES OF MATERIALS USED IN THE FOLLOWING DEVICES: Sealed Relay
Device.
16
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual
1.3.2
Field Installation

Input Terminal Block (CN3) suitable for 12-28 AWG (0.0804-3.31 mm²) wire
size, torque value 4.5 lb-in (0.5085 Nm).

Output Terminal Block (CN5, CN6) suitable for 14 -28 AWG (0.0804-2.1 mm²)
wire size, torque value 1.7 lb-in (0.1921 Nm) .

Output Terminal Block (CN7) suitable for 14 -28 AWG (0.0804-2.1 mm²) wire
size, torque value 1.7 lb-in (0.1921 Nm) .

The equipment shall be installed in an enclosure that provides a degree of protection
not less than IP 54 in accordance with EN 60079-15 and accessible only by the use of a
tool.
Introduction
17
rBOX510-6COM(ATEX&C1D2) User’s Manual
1.4
Dimensions
The following diagrams show you dimensions and outlines of the rBOX5106COM(ATEX&C1D2).
18
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual
1.5
I/O Outlets
The following figures show you I/O outlets on front view and top view of the
rBOX510-6COM(ATEX&C1D2).
Introduction
19
rBOX510-6COM(ATEX&C1D2) User’s Manual
This page is intentionally left blank.
20
Introduction
rBOX510-6COM(ATEX&C1D2) User’s Manual
CHAPTER 2
HARDWARE INSTALLATION
The rBOX510-6COM(ATEX&C1D2) is convenient for your various hardware
configurations. The chapter 2 will show you how to install the hardware. It includes:
2.1
Installing Din-rail Mounting
The rBOX provides Din-rail Mount that customers can install as below:
Step 1
Prepare Din-rail Mount assembling components (screws and bracket) ready.
Step 2
Assembly the bracket to the system, and fasten screws tight.
Note: Please notice the Din-rail holes with Wall-mounting holes while assembly the bracket
to system.
Hardware Installation
21
rBOX510-6COM(ATEX&C1D2) User’s Manual
Setting up rBOX series by Din-rail mounting
The rBOX set up by Din-rail mounting as below:
Step 1
Fixing the rail firstly.
Step 2
Set up the rBOX on the rail by Din-rail mounting
22
Hardware Installation
rBOX510-6COM(ATEX&C1D2) User’s Manual
2.2
Installing Wall Mounting (optional)
The rBOX provides Wall Mounting that customers can install as below:
Step 1
Prepare Wall Mount assembling components (screws and bracket) ready.
Step 2
Assembly the bracket to the system, and fasten screws tight.
Note:
Please notice the Din-rail holes with Wall-mounting holes while assembly the
bracket to system.
Hardware Installation
23
rBOX510-6COM(ATEX&C1D2) User’s Manual
This page is intentionally left blank.
24
Hardware Installation
rBOX510-6COM(ATEX&C1D2) User’s Manual
CHAPTER 3
AMI UEFI BIOS UTILITY
The AMI UEFI BIOS provides users with a built-in Setup program to modify basic
system configuration. All configured parameters are stored in a flash-backed-up to
save the Setup information whenever the power is turned off .
3.1
Entering Setup
To enter the setup screens, follow the steps below:
1.
Turn on the computer and press the <Del> key immediately.
2.
After you press the <Del> key, the main BIOS setup menu displays. You can access the
other setup screens from the main BIOS setup menu, such as the Advanced and
Chipset menus.
AMI UEFI BIOS Utility
25
rBOX510-6COM(ATEX&C1D2) User’s Manual
3.2
The Main Menu
Once you enter the AMI BIOS Aptio Setup Utility, the Main Menu appears on the
screen. In the Main Menu, there are several Setup functions and a couple of Exit
options for your selection. Use Select Screen Keys (or Move Keys) to select the
Setup Page you intend to configure then press <Enter> to accept or enter its sub menu.
System Date
The date format is <day> <month> <date> <year>.
System Time
This item shows current time of your system with the format <hour> <minute> <second>. The
time is calculated based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00.
26
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual
3.3
Advanced Features
This Advanced section allows users to configure and improve your system, to set up
some system features according to your preference. You can select any of the
items in the left frame of the screen to go to the sub menus:

Launch PXE opROM
The default setting boot from onboard LAN PxE Rom is [Disabled]
(Please refer below graphics.)
AMI UEFI BIOS Utility
27
rBOX510-6COM(ATEX&C1D2) User’s Manual

PCIE/mSATA Mini Card configuration
The default setting for mini card is PCIE.
(Please refer below graphics.)
Note: SSD and mSATA function can be either one, it can be select by BIOS menu.
mSATA and wireless use the same slot, and only one of them can be selected.
28
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual

COM Port Interface Type
The default setting for all Serial Ports are RS232.
You can change the setting by selecting the value you want in each COM Port Type.
(Please refer below graphics.)
AMI UEFI BIOS Utility
29
rBOX510-6COM(ATEX&C1D2) User’s Manual
30
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual
Supports internal 120 ohms terminator in RS422 & RS485 mode.
(Please refer below graphics.)
AMI UEFI BIOS Utility
31
rBOX510-6COM(ATEX&C1D2) User’s Manual

H/W Monitor
Scroll to this item and press <Enter> to view the monitor hardware status.
(Please refer below graphics.)
32
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual

CPU Configuration
Scroll to this item and press <Enter> to view the CPU Configuration informations.
(Please refer below graphics.)
AMI UEFI BIOS Utility
33
rBOX510-6COM(ATEX&C1D2) User’s Manual
34
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual

IDE Configuration
Scroll to this item and press <Enter> to view the IDE Configuration informations.
(Please refer below graphics.)
AMI UEFI BIOS Utility
35
rBOX510-6COM(ATEX&C1D2) User’s Manual
3.4
Chipset Feature
This section contains completely optimized chipset’s features in the system

USB Configuration
Scroll to this item and press <Enter> to view the USB Configuration informations.
(Please refer below graphics.)
36
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual
3.5
Security
The default setting for Administrator Password is “Not setting passwords”.
The Security menu allows users to change the security settings for the system.
You can set the password for both Administrator Password and User Password.
(Please refer below graphics.)
AMI UEFI BIOS Utility
37
rBOX510-6COM(ATEX&C1D2) User’s Manual
Note: The BIOS default has no password, when user created the password, please
remember the password number, if users forget password the RMA is the only
solution.
38
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual
3.6
Boot Type
The Boot Option Priorities can select by Boot Option #1, #2…
(Please refer below graphics.)
AMI UEFI BIOS Utility
39
rBOX510-6COM(ATEX&C1D2) User’s Manual
Hard Drive BBS Priorites supports the hard drive boot option.
40
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual
AMI UEFI BIOS Utility
41
rBOX510-6COM(ATEX&C1D2) User’s Manual
3.7
Save & Exit
This section allows you to determine whether or not to accept your modifications. Type “Y” to
quit the setup utility and save all changes. Type “N” to bring you back to the Previous Setup
utility.
(Please refer below graphics.)
42
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual
AMI UEFI BIOS Utility
43
rBOX510-6COM(ATEX&C1D2) User’s Manual
This page is intentionally left blank.
44
AMI UEFI BIOS Utility
rBOX510-6COM(ATEX&C1D2) User’s Manual
APPENDIX A
WATCHDOG TIMER
About Watchdog Timer
After the system stops working for a while, it can be auto-reset by the watchdog timer. The
integrated watchdog timer can be set up in the system reset mode by program.
How to Use Watchdog Timer
The following example enables configuration using debug tool.
Enable WDT

Enable configuration:
O 4E 87 ; Un-lock super I/O
O 4E 87

Select logic device:
O 4E 07
O 4F 08

WDT device enable:
O 4E 30
O 4F 01

Set timer unit:
O 4E F0
O 4F 00 ; (00: Sec; 08:Minute)

Set base timer:
O 4E F1
O 4F 0A ; Set reset time (where 0A (hex) = 10sec)
Watchdog Timer
45
rBOX510-6COM(ATEX&C1D2) User’s Manual
Disable WDT

Enable configuration:
O 4E 87 ; Un-lock super I/O
O 4E 87

Select logic device:
O 4E 07
O 4F 08

WDT device disable:
O 4E 30
O 4F 00
46
Watchdog Timer
rBOX510-6COM(ATEX&C1D2) User’s Manual
APPENDIX B
DIO Command
How to Use DIO Registers
DIO Command
47
rBOX510-6COM(ATEX&C1D2) User’s Manual
This page is intentionally left blank.
48
DIO Command