rBOX120-FL Series Robust Din-rail Fanless Embedded System User’s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual. Axiomtek reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd. Copyright 2013 Axiomtek Co., Ltd. All Rights Reserved May 2013, Version A1 Printed in Taiwan ii Safety Precautions Before getting started, please read the following important safety precautions. 1. The rBOX120-FL does not come equipped with an operating syst em. An operating system must be loaded first before installing any software into the computer. 2. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. 3. Disconnect the power cord from the rBOX120-FL before making any installation. Be sure both the system and the external devices are turned OFF. Sudden surge of power could ruin sensitive components. Make sure the rBOX120-FL is properly grounded. 4. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not spray any liquid cleaner directly onto the screen. 6. Do not leave this equipment in an uncontrolled environment where the storage temperature is below -45℃ or above 85℃. It may damage the equipment. 7. Do not open the system ’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following pr ecautions: Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body. W hen handling boards and components, wear a wrist -grounding strap, available from most electronic component stores . iii Classification 1. Degree of production against electric shock: not classified 2. Degree of protection against the ingress of water: IP30 3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. 4. Mode of operation: Continuous 5. Type of protection against electric shock: Class I equipment General Cleaning Tips You may need the following precautions before you begin to clean the computer . W hen you clean any single part or component for the com puter, please read and understand the details below fully. W hen you need to clean the device, please rub it with a pi ece of dry cloth. 1. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor. 2. Turn the system off before you start to clean up the component or computer. 3. Never drop the components inside the computer or get circuit bo ard damp or wet. 4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of cleaning. Some individuals may be allergic to the ingredients. 5. Try not to put any food, drink or cigarette around the computer. iv Cleaning Tools Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals. Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals. Keep in mind that some components in your computer may only be able to be cleaned using a product designed for cleaning that component, if this is the case i t will be mentioned in the cleaning. Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although paper towels or tissues can be used on most hardware as well, we still recommend you to rub it with a piece of cloth. W ater or rubbing alcohol: You may moisten a piece of cloth a bit with some water or rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the plastics parts. Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of a computer can be one of the best methods of cleaning a computer. Over time these items can restrict the airflow in a computer and cause circuitry to corrode. Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard, mouse, and other locations. Foam swabs: W henever possible it is better to use lint free swabs such as foam swabs. We strongly recommended that you should shut down the system before you start to clean any single components. Note Please follow the steps below: 1. Close all application programs 2. Close operating software 3. Turn off power 4. Remove all device 5. Pull out power cable v Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair, we strongly recommended that you should inform your Axiomtek distributor as soon as possible for the suitable solution. For the computers that are no longer useful or no longer working well, please contact your Axiomtek distributor for recycling and we will make the proper arrangement. Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co., Ltd. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation. ® ® Intel and Pentium are registered trademarks of Intel Corporation. MS-DOS, Microsoft C and QuickBASIC are trademarks of Microsoft Corporation. VIA is a trademark of VIA Technologies, Inc. SST is a trademark of Silicon Storage Technology, Inc. UMC is a trademark of United Microelectronics Corporation. Other brand names and trademarks are the properties and registered brands of their respective owners . vi Table of Contents Disclaimers..................................................................................................... ii Safety Precautions ........................................................................................ iii Classification ................................................................................................ iv General Cleaning Tips .................................................................................. iv Cleaning Tools ............................................................................................... v Scrap Computer Recycling .......................................................................... vi CHAPTER 1 INTRODUCTION ............................................. 1 1.1 General Description ............................................................................... 1 1.2 System Specifications ........................................................................... 4 1.2.1 1.2.2 1.2.3 1.2.4 1.2.5 1.2.6 1.2.7 1.2.8 1.2.9 1.2.10 1.2.11 1.2.12 1.2.13 1.2.14 1.2.15 1.2.16 1.2.17 1.2.18 1.2.19 1.2.20 1.2.21 1.2.22 1.2.23 CPU .................................................................................................................... 4 Chipset ................................................................................................................ 4 BIOS ................................................................................................................... 4 System Memory .................................................................................................. 4 Graphics Chip ..................................................................................................... 4 Video Memory ..................................................................................................... 5 LAN ..................................................................................................................... 5 Storage ............................................................................................................... 5 USB ..................................................................................................................... 6 COM .................................................................................................................... 8 Power ................................................................................................................ 12 WatchDog Timer (WDT) ................................................................................... 13 Digital I/O Connector and Pin Definition ........................................................... 15 System LED ...................................................................................................... 22 Alarm Contact ................................................................................................... 28 Wireless (3G/GPRS & Wifi) .............................................................................. 34 Reset Bottom .................................................................................................... 34 Operation Temperature .................................................................................... 34 Storage Temperature ........................................................................................ 34 Humidity ............................................................................................................ 34 Weight ............................................................................................................... 34 Dimensions ....................................................................................................... 34 System I/O Outlet .............................................................................................. 35 1.3 Dimensions ........................................................................................... 36 1.4 I/O Outlets ............................................................................................. 37 1.5 Packing List .......................................................................................... 38 CHAPTER 2 HARDWARE INSTALLATION .......................... 39 2.1 2.2 2.3 2.4 Installing the Memory Module ............................................................. 39 Installing the Hard Disk Drive ............................................................. 43 Installing Din-rail Mounting ................................................................. 48 Installing Wall Mounting (optional)..................................................... 55 CHAPTER 3 PHOENIX-AWARD BIOS UTILITY .................... 57 vii 3.1 Entering Setup ..................................................................................... 57 3.2 Control Keys ......................................................................................... 57 3.3 The Main Menu ..................................................................................... 58 3.4 Standard CMOS Setup Menu .............................................................. 59 3.5 Advanced BIOS Features .................................................................... 62 3.6 Advanced Chipset Features ................................................................ 72 3.7 Integrated Peripherals ......................................................................... 74 3.8 Power Management Setup .................................................................. 81 3.9 PnP/PCI Configuration Setup .............................................................. 82 3.10 PC Health Status .................................................................................. 88 3.11 Load Optimized Defaults ..................................................................... 89 3.12 Set Supervisor/User Password ........................................................... 90 3.13 Save & Exit Setup................................................................................. 92 3.14 Exit Without Saving ............................................................................. 93 viii rBOX120-FL Series User’s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the rBOX120-FL. The Chapter 1 includes the following sections: 1.1 General Description System Specification Dimensions I/O Outlets Package List General Description The rBOX120-FL Din-rail fanless embedded systems are suitable for communications control and for protocol converter applications in critical environments. Built for rugged work environments, the rBOX120-FL series features ® an extra low power consumption Intel ATOM ™ Z510PT (1.1 GHz) or Z520PT (1.33 GHz) processors supporting industrial temperature range of -40℃ to +70℃. Their front accessible I/O cabling is very convenient for wiring and maintenance. The rBOX120-FL series offers a VGA output, making it particularly well -suited for communication control, SCADA and industrial automation. Its compact size with D inrail mounting allows for easy installation into c ontrol cabinet. Pre-installed with Linux, ® ® ® W indows CE 6.0. W indows 7 embedded or W indows XP embedded, the rBOX120-FL series provides programmers with a friendly environment for developing application software at a lower cost. Introduction 1 rBOX120-FL Series User’s Manual The rBOX120-FL is robust industrial-grade hardware design and adopts the advanced cooling system , besides, supporting the CompactFlash™, which makes it especially suitable for field control & monitoring system solution for following markets: Utility Industries (Water; Energy; Chemical Plant; Mining…) Public Transportation Industries (Traffic/ Highway Control; Train/Bus Control …) Homeland Security (Weather Monitoring/Alarm System …) Features 1. 2. Fanless and no internal cabling design Wide temperature operation of -40℃ - +70℃ 3. Supports 3 10/100/1000 Ethernets with Magnetic Isolation Protection 4. 2 Isolation COM Ports 5. 1 Isolation DIO Ports (8-In/8-Out) with Dry/Wet contacts 6. 2 Watchdog Timers 7. LED Indicators (Power, Alarm, Ready/Active, COM (TX D,RXD) ) 8. 2 Wireless (3G/GPRS & Wifi) 9. SNMP V1/V2c 10. Support one 2.5” SATA SSD (or HDD) and one CompactFlash™ 11. 2 power paths with terminal block and 12–48VDC 12. Din-rail mounting 13. Wall mounting (optional) 14. Meet safety agency requirements (UL508,UL60950-1), passed heavy industrial CE & FCC Part 18 Class A and pre-tested okay EN50121-4 (for Railway application) Embedded O.S. Supported The rBOX120-FL not only supports W indows embedded OS, such as W indows ® ® XP, but also supports XP embedded, W indows ® 7 embedded, ® W indows CE 6.0 and Linux. For storage device, the rBOX120-FL supports one type II CompactFlash ™ slot. 2 Introduction rBOX120-FL Series User’s Manual Intelligent AXView & SNMP V1/V2c The rBOX120 features SNMP V1/V2c support for secured network management. To streamline implementation of management applications, Axiomtek has launched exclusive “AXView” monitoring software package for customers to build their own management systems easily and quickly. Axiomtek AXView also contains a variety of easy-to-use management utilities, agent services and libraries. For more product information, please visit our global website on Axiomtek AXView http://axiomtek.com/products/ViewProduct.asp?view=1001 Introduction 3 rBOX120-FL Series User’s Manual 1.2 System Specifications 1.2.1 CPU ® Onboard Intel ATOM™ Z510PT (1.1 GHz) or Z520PT (1.33 GHz) processors with FSB 400/533MHz. 1.2.2 Chipset Intel System Controller Hub US15W PT 1.2.3 BIOS Phoenix AwardBIOS 1.2.4 System Memory One 200-pin SO-DIMM support DDR2 400/533MHz max. up to 2GB 1.2.5 4 Graphics Chip Intel GMA500 graphics Core integrate in US15W PT DB15 VGA port VGA IO Pin Define : Pin Signal Pin Signal Pin Signal 1 Red 2 Green 3 Blue 4 N.C. 5 GND 6 DETECT 7 GND 8 GND 9 VCC 10 GND 11 N.C. 12 DDC DATA 13 Horizontal Sync 14 Vertical Sync 15 DDC CLK Introduction rBOX120-FL Series User’s Manual 1.2.6 Video Memory 1.2.7 Share Memory max. up to 254MB LAN LAN 1 / LAN 2 / LAN 3 ．GBE Intel 82574, 10/100/1000Mbps LAN w/ Magnetic Isolation Protection 1.5KV ． LED definition: Active LED (Yellow flashing), 10 LAN LED (NO Light), 100 LAN LED (Green Light), 1000 LAN LED (Orange Light) GbE(10M/100M/1000M) Pin Signal 1 MDI0+ 2 MDI0- 3 MDI1+ 4 MDI1- 5 MDI2+ 6 MDI2- 7 MDI3+ 8 MDI3- A Active LED (Yellow) B 100 LAN LED (Green)/ 1000 LAN LED (Orange) 1.2.8 A B 87654321 Storage 1 x 2.5” SATA SSD (or HDD) drive bay 1 x CompactFlash TypeII slot (easy-to- access) Introduction 5 rBOX120-FL Series User’s Manual 1.2.9 USB 2 x USB2.0 W ith power distribution control and over current protection USB Pin Define : Pin 1 Signal USB Port 0 USB VCC (+5V level) Pin 5 Signal USB Port 1 USB VCC 2 USB #0_D- 6 USB #1_D- 3 USB #0_D+ 7 USB #1_D+ 4 Ground (GND) 8 Ground (GND) 5 6 7 8 (+5V level) 1 2 3 4 USB power (5V) distribution control. Some program and sample code for USB power distribution control are offered in Windows and Linux. - W indows: Please refer it from our Axiomtek AXView which on Axiomtek’s website directly. - Linux : Please refer it from our Axiomtek’s website directly. Axiomtek’s website for AXView : http://axiomtek.com/products/ViewProduct.asp?view=1001 6 Introduction rBOX120-FL Series User’s Manual AXView Version Sample Code C (or C#) AXView Axiomtek’s website for Linux : http://www.axiomtek.com/products/ViewProduct.asp?view=1075 USB Power Distribution Control Sample code: Windows: \AXView Version\Samplecode\c\AXView\SetUSBPowerDisable \AXVIEW _DLL_Test.cpp Linux: \rBox120-bsp-user-1.0.0\rbox120\src\librb100.c int _rb201_usb_power(int number, int onoff) Introduction 7 rBOX120-FL Series User’s Manual 1.2.10 COM 2 ports DB9 Pin Define RS-232/422/485 ESD Protection 15KV Magnetic Isolation Protection 2KV COM1,COM2 speed up to 115.2kbps rBOX support jumper less design. All of the COM port interface RS232/422/485 can be selected by BIOS menu or software program. It also supports Auto Flow Control in RS485 mode Serial Port Pin Define : (DB9 Male) rBOX120 COM1/COM2 Pin RS-232 RS-422 RS-485 1 DCD TX- Data- 2 RXD TX+ Data+ 3 TXD RX+ -- 4 DTR RX- -- 5 Ground Ground Ground 6 DSR -- -- 7 RTS -- -- 8 CTS -- -- 9 RI -- -- Some program and sample code for COM port interface type are offered in W indows and Linux. - W indows:Please refer it from our Axiomtek AXView which on Axiomtek’s website directly. - Linux : Please refer it from our Axiomtek’s website directly. 8 Introduction rBOX120-FL Series User’s Manual Axiomtek’s website for AXView : http://axiomtek.com/products/ViewProduct.asp?view=1001 AXView Version Sample Code C (or C#) AXView Introduction 9 rBOX120-FL Series User’s Manual Axiomtek’s website for Linux : http://www.axiomtek.com/products/ViewProduct.asp?view=1075 COM port interface selection Sample Code : -Set COM port interface type(W indows, Linux) Windows: -RS232/422/485 interface selection: \AXView Version\Sample code\c\AXView\SetComPort\ AXVIEW _DLL_Test.cpp 10 Introduction rBOX120-FL Series User’s Manual Linux: -RS232/422/485 interface selection: \rBox120-bsp-user-1.0.0\rbox120\src\librb100.c int _rb210_set_comport(int number, int type) http://www.axiomtek.com/products/ViewProduct.asp?view=1075 Introduction 11 rBOX120-FL Series User’s Manual 1.2.11 Power 2 power paths 2 power sources must be same voltage and DC input range 12-48V. Main power source is for Input Power Path 1, Backup power source is for Input Power Path 2. Only one power source must be for Input Power Path 1. DC Input has UVP/OVP/Reverse protection. Reset Button without Power Switch DC Terminal Block Pin DC Signal Name 1 AL- 2 AL+ 3 SG 4 SG 5 GND 6 DC2 7 GND 8 DC1 Note 12 1. If 2 power sources aren’t same voltage and the system will be possible damage. 2. When the system is shoutdown after, if users press the Reset Button for 3 seconds and the system will be restarted. Introduction rBOX120-FL Series User’s Manual 1.2.12 WatchDog Timer (WDT) rBox support two W atchdog timers. Those can cause system reset when timer expired. W DT 1 : one step is 1sec, 255 levels W DT 2 : one step is 250ms, 255 levels Some program and sample code for two W atchdog timers are offered in W indows and Linux. - W indows : Please refer it from our Axiomtek AXView which on Axiomtek’s website directly. - Linux : Please refer it from our Axiomtek’s website directly. Axiomtek’s website for AXView : http://axiomtek.com/products/ViewProduct.asp?view=1001 AXView Version Sample Code C (or C#) AXView Axiomtek’s website for Linux : http://www.axiomtek.com/products/ViewProduct.asp?view=1075 Introduction 13 rBOX120-FL Series User’s Manual Watch Dog Timer Sample code: -Super IO(Linux) -CPLD(W indows, Linux) Windows: -CPLD: \AXView Version\Sample code\c\AXView\SetW atchDog\ AXVIEW _DLL_Test.cpp Linux: \rBox120-bsp-user-1.0.0\rbox120\src\librb100.c -Super IO: int _rm820_W DT_enable(unsigned char scale, unsigned char timeout) int _rm820_W DT_disable(void) int _rm820_W DT_reload(void) int _rm820_read_W DT_config(unsigned int *time) -CPLD: unsigned char _rb210_get_W DT_value(void) int _rb210_W DT_enable(unsigned char timeout) int _rb210_W DT_disable(void) 14 Introduction rBOX120-FL Series User’s Manual 1.2.13 Digital I/O Connector and Pin Definition 8bit DI and 8bit DO 3KV optical isolation DIO Design Specification Digital Input Input Channels 8,source type Input Voltage 0 to 24VDC Digital Input Levels for Dry Contacts Logic level 0:Close to GND Digital Input Levels for W et Contacts Logic level 0:+10V to +24V (DI To XIN_COM-) Logic level 1:Open Logic level 1:+3V max. Digital Output Output Channels 8,sink type Output Current Max. 200 mA per channel On-state Voltage 24VDC nominal, open collector to 30V I Some program and sample code for DIO are offered in W indows and Linux. - W indows : Please refer it from our Axiomtek AXView which on Axiomtek’s website directly. - Linux : Please refer it from our Axiomtek’s website directly. Axiomtek’s website for AXView : http://axiomtek.com/products/ViewProduct.asp?ptype3=268&pos=1&ptype 2=229&ptype1=209 Introduction 15 rBOX120-FL Series User’s Manual AXView Version Sample Code C (or C#) AXView Axiomtek’s website for Linux : http://www.axiomtek.com/products/ViewProduct.asp?view=1075 GPIO control DI: - Get the DI register (W indows, Linux) - Set DI polarity (W indows) DO: - Get DO register (Linux) - Set DO register (W indows, Linux) 16 Introduction rBOX120-FL Series User’s Manual DI/DO Sample Code : Windows: -Set DI polarity: \AXView Version\Sample code\1.0.2\c\SetW atchDog\ AXVIEW _DLL_Test.cpp -Get DI: \AXView Version\Sample code\1.0.2\c\GetDi\ AXVIEW _DLL_Test.cpp -Set DO: \AXView Version\Sample code\1.0.2\c\SetDO\ AXVIEW _DLL_Test.cpp Linux: \rBox120-bsp-user-1.0.0\rbox120\src\librb100.c -Get DI: int _ax93612_read_DI(unsigned char *data) -Get DO: int _ax93612_read_DO(unsigned char *data) -Set DO: int _ax93612_write_DO(unsigned char data) The updated latest version of AXView and Linux will be released on Axiomtek’s global website directly. Note Introduction 17 rBOX120-FL Series User’s Manual 18 DIO 8 in & out of DB25 Female Pin Function Pin Function 1 NC 2 XIN00 3 XIN02 4 XIN04 5 XIN06 6 XIN_COM+ 7 XIN_COM- 8 NC 9 XOUT06 10 XOUT04 11 XOUT02 12 XOUT00 13 XOUTCOM+ 14 NC 15 XIN01 16 XIN03 17 XIN05 18 XIN07 19 NC 20 NC 21 XOUT07 22 XOUT05 23 XOUT03 24 XOUT01 25 XOUTCOM- Remark: Signal Name Meaning XINCOM+ Plus common for Input Group XINCOM- Minus common for Input Group XIN00~07 Input Group NC Not connection XOUTCOM- Minus common for Output Group XOUTCOM+ Plus common for Output Group XOUT00~07 Output Group Introduction rBOX120-FL Series User’s Manual DIO operation schematic diagram Reference 1. Reference 2. Introduction 19 rBOX120-FL Series User’s Manual Reference 3 Digital Input Wiring Reference 4 Digital Output Wiring 20 Introduction rBOX120-FL Series User’s Manual rBOX120 How to control /program the I/O Introduction 21 rBOX120-FL Series User’s Manual 1.2.14 System LED For maintenance issue, IO board will have below LED. 1. DC PWR1 : Green 2. DC PWR2 : Green 3. Alarm : Red 4. OS Ready : Yellow 5. COM TX1 : Green 6. COM RX1 : Green 7. COM TX2 : Green 8. COM RX2 : Green LED Name Description Color DC PWR1 Indicate the DC1 input status. When the DC input is acceptable, the LED will ON. Green DC PWR2 Indicate the DC2 input status. When the DC input is acceptable, the LED will ON. Green Note The LED will ON if having below condition. 1. DC PWR1 or PWR2 is lost. (default) 2. User define event. Alarm Red The behavior of Alarm and Relay are the same. When the LED of Alarm is ON and the Relay will be turn on at the same time. The LED for RDY/ACT can help users to judge BIOS finish or not and the OS can normal work or not. When the BIOS finish the configuration of system, the LED will ON. After this the LED will flash when the storage is accessed. RDY/ACT - The LED will flash when the storage is accessed. Yellow - The LED always ON without any flash for a long time, the OS is possible crashed. - The LED isn’t ON for a long time, it means the system is on shutdown status. COM TX1 When COM1 transmit data the LED will on. Green COM RX1 When COM1 receive data the LED will on. Green COM TX2 When COM2 transmit data the LED will on. Green COM RX2 When COM2 receive data the LED will on. Green When the system is shoutdown after, if users press the Reset Button for 3 seconds and the system will be restarded. Note 22 Introduction rBOX120-FL Series User’s Manual Some program and sample code for Alarm LED and Relay Output are offered in W indows and Linux. - W indows : Please refer it from our Axiomtek AXView which on Axiomtek’s website directly. - Linux : Please refer it from our Axiomtek’s website directly. Alarm LED and Relay output Sample Code: - Set Alarm LED and Relay status(W indows, Linux) - Get Alarm LED and Relay status(W indows, Linux) - Get Power status( W indows, Linux) Windows: -Get the LED status: \AXView Version\Samplecode\c\AXView\GetLEDStatus \AXVIEW _DLL_Test.cpp -Set the LED status: \AXView Version\Samplecode\c\AXView\SetLED \AXVIEW _DLL_Test.cpp -Get Power Status: \AXView Version\Sample code\c\AXView\GetPowerSattus \AXVIEW _DLL_Test.cpp Linux: \rBox120-bsp-user-1.0.0\rbox120\src\librb100.c -Get the LED status: int _rb210_get_power_usr_alarm_status(void) -Set the LED status: int _rb210_power_alarm_ctl(int onoff) -Get Power Status: int _rb210_read_power_status(int number) Introduction 23 rBOX120-FL Series User’s Manual Axiomtek’s website for AXView : AXView Version Sample Code C (or C#) AXView 24 Introduction rBOX120-FL Series User’s Manual Axiomtek’s website for Linux : http://www.axiomtek.com/products/ViewProduct.asp?view=1075 Introduction 25 rBOX120-FL Series User’s Manual Below pictures are the LED example: 26 Introduction rBOX120-FL Series User’s Manual Introduction 27 rBOX120-FL Series User’s Manual 1.2.15 Alarm Contact The rBox can support two DC power source. W hen lost one of them will cause Alarm LED on and trigger Relay out for remote notice. W e also provide the register for user to define their event for trigger the Alarm LED and Relay. Alarm LED and Relay output have the same activity depend on DC status and register control. 1 relay output Relay output with 0.5A @ 30VDC Event : Power Fail and User define Some program and sample code for Alarm LED and Relay Output are offered in W indows and Linux. - W indows : Please refer it from our Axiomtek AXView which on Axiomtek’s website directly. - Linux : Please refer it from our Axiomtek’s website directly. 28 Introduction rBOX120-FL Series User’s Manual Axiomtek’s website for AXView : http://axiomtek.com/products/ViewProduct.asp?view=1001 AXView Version Sample Code C (or C#) AXView Introduction 29 rBOX120-FL Series User’s Manual Axiomtek’s website for Linux : http://www.axiomtek.com/products/ViewProduct.asp?view=1075 Alarm LED and Relay output Sample Code: - Set Alarm LED and Relay status(W indows, Linux) - Get Alarm LED and Relay status(W indows, Linux) - Get Power status( W indows, Linux) Windows: -Get the LED status: \AXView Version\Samplecode\c\AXView\GetLEDStatus \AXVIEW _DLL_Test.cpp -Set the LED status: \AXView Version\Samplecode\c\AXView\SetLED \AXVIEW _DLL_Test.cpp -Get Power Status: \AXView Version\Sample code\c\AXView\GetPowerSattus \AXVIEW _DLL_Test.cpp 30 Introduction rBOX120-FL Series User’s Manual Linux : -Get the LED status: int _rb210_get_power_usr_alarm_status(void) -Set the LED status: int _rb210_power_alarm_ctl(int onoff) -Get Power Status: int _rb210_read_power_status(int number) rBOX Alarm Application: Troubleshooting is very important in many applications. In the rBox series we can provide three kinds of way for troubleshooting. Alarm LED Relay out SNMP through AXView 1. Maintenance Staff can check the Alarm LED for basic troubleshooting Introduction 31 rBOX120-FL Series User’s Manual 2. Relay output Below is a very simple application for remote notice use relay and lamp. a) Normal b) W arning 32 Introduction rBOX120-FL Series User’s Manual c) Relay wiring of rBox Introduction 33 rBOX120-FL Series User’s Manual 3. SNMP 1.2.16 Wireless (3G/GPRS & Wifi) 1 x Full size Mini Card (Only supports USB interface on 3G/GPRS) 1 x Half size Mini Card (Supports PCIe ans USB interface on Wifi) 1 x SIM Card Socket (easy-to-access). 1.2.17 Reset Bottom 1 x Reset bottom When the system is shoutdown after, if users press the Reset Button for 3 seconds and the system will be restarted. Note 1.2.18 1.2.19 1.2.20 1.2.21 1.2.22 34 Operation Temperature -40℃ ~ +70℃ (-40 ºF ~ +158ºF), with W.T. (Memory, CF, SSD/HDD) Storage Temperature -45℃ ~ +85℃ (-49 ºF ~ +185ºF) Humidity 5% ~ 95% (non-condensation) Weight 1.38 kg (3 lb) for rBOX120 Dimensions 100.6mm(3.18”) (W) x110mm(4.33”) (D) x135mm(5.31”) (H) Introduction rBOX120-FL Series User’s Manual 1.2.23 System I/O Outlet Two 9-pin D-Sub male connectors, COM1~COM2 One 15-pin D-Sub female connector for VGA Three 10/100/1000Mbps Ethernet with Magnetic Isolation Protection Two USB 2.0 connectors Two DC Powers Input with terminal block Alarm Contact Two Wirelesses (3G/GPRS & WiFI) All specifications and images are subject to change without notice. Note Introduction 35 rBOX120-FL Series User’s Manual 1.3 Dimensions The following diagrams show you dimensions and outlines of the rBOX120-FL 36 Introduction rBOX120-FL Series User’s Manual 1.4 I/O Outlets The following figures show you I/O outlets on front view and top view of the rBOX120-FL. Front View Top View Introduction 37 rBOX120-FL Series User’s Manual 1.5 Packing List The package bundled with your rBOX120-FL should contain the following items: 38 rBOX120-FL System Unit x 1 CD x 1 (For Driver and User’s Manual) Power terminal block x1 Din-rail kit x1 Screws Quick Manual x1 Introduction rBOX120-FL Series User’s Manual CHAPTER 2 HARDWARE INSTALLATION The rBOX120-FL is convenient for your various hardware configurations, such as TM Memory Module and CompactFlash card. The chapter 2 will show you how to install the hardware. It includes: 2.1 Installing the Memory Module Step 1 Turn off the system. Step 2 Loosen these screws, and remove the top cover from the system. Hardware Installation 39 rBOX120-FL Series User’s Manual 40 Hardware Installation rBOX120-FL Series User’s Manual Step 3 Hold one side of the module, and insert the gold colored contact into the socket. Push the module down. Step 4 The memory module is locked by two latches on the sides. Hardware Installation 41 rBOX120-FL Series User’s Manual Step 5 42 Put the cover back to the system, and fasten screws tight close the chassis. Hardware Installation rBOX120-FL Series User’s Manual 2.2 Step 1 Step 2 Installing the Hard Disk Drive Turn off the system. Loosen these screws, and remove the cover from the system. Hardware Installation 43 rBOX120-FL Series User’s Manual Step 3 Locate the Hard Disk Drive socket. Step 4 Loosen these screws and remove the Hard Disk Drive bracket. 44 Hardware Installation Step 5 Step 6 rBOX120-FL Series User’s Manual Insert the HDD into the socket until it is firmly seated. Put the cover back to the system, and fasten screws tight close the chassis. Hardware Installation 45 rBOX120-FL Series User’s Manual 46 Hardware Installation rBOX120-FL Series User’s Manual Hardware Installation 47 rBOX120-FL Series User’s Manual 2.3 Installing Din-rail Mounting The rBOX provides Din-rail Mount that customers can install as below: Step 1 Prepare DIN Mount assembling components (screws and bracket) ready. Step 2 Assembly the bracket to the system, and fasten screws tight. 48 Hardware Installation rBOX120-FL Series User’s Manual Please notice the Din-rail holes with Wall-mounting holes while assembly the bracket to system. Note Hardware Installation 49 rBOX120-FL Series User’s Manual Please notice the Din-rail holes with Wall-mounting holes while assembly the bracket to system. Note The Din-rail hole drawing for rBOX120 is listed below: 50 Hardware Installation rBOX120-FL Series User’s Manual The Din-rail kit drawing is listed below: Hardware Installation 51 rBOX120-FL Series User’s Manual 52 Hardware Installation rBOX120-FL Series User’s Manual Setting up rBOX by Din-rail mounting The rBOX set up by Din-rail mounting as below: Step 1 Fixing the rail firstly. Hardware Installation 53 rBOX120-FL Series User’s Manual Step 2 54 Set up the rBOX on the rail by Din-rail mounting 1 2 3 4 Hardware Installation rBOX120-FL Series User’s Manual 2.4 Installing Wall Mounting (optional) The rBOX provides W all Mounting that customers can install as below: Step 1 Prepare Wall Mount assembling components (screws and bracket) ready. Step 2 Assembly the bracket to the system, and fasten screws tight. Hardware Installation 55 rBOX120-FL Series User’s Manual Please notice the Din-rail holes with Wall-mounting holes while assembly the bracket to system. Note 56 Hardware Installation rBOX120-FL Series User’s Manual CHAPTER 3 PHOENIX-AWARD BIOS UTILITY The Phoenix-Award BIOS provides users with a built-in Setup program to modify basic system configuration. All configured parameters are stored in a flash-backedup to save the Setup information whenever the power is turned off . 3.1 Entering Setup There is one way to enter the Setup program. You may either turn ON the computer and press <Del> immediately. 3.2 Control Keys Up arrow Move to the previous item Down arrow Move to the next item Left arrow Move to the left side Right arrow Move to the right side Esc key Main Menu -- Quit and delete changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu PgUp/“+”key Increase the numeric value or make changes PgDn/“−“ key Decrease the numeric value or make changes F6 key Load the default CMOS value from BIOS default table, only for Option Page Setup Menu F7 key Load the Setup default, only for Option Page Setup Menu F10 key Save all the CMOS changes, only for Main Menu PHOENIX-AWARD BIOS UTILITY 57 rBOX120-FL Series User’s Manual 3.3 The Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu appears on the screen. In the Main Menu, there are several Setup functions and a couple of Exit options for your selection. Use arrow keys to select the Setup Page you intend to configure then press <Enter> to accept or enter its sub-menu. Note 1. If your computer can not boot after making and saving system changes with Setup, the Award BIOS will reset your system to the CMOS default settings via its built-in override feature. 2. It is strongly recommended that you should avoid changing the chipset’s defaults. Both Award and your system manufacturer have carefully set up these defaults that provide the best performance and reliability. 58 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual 3.4 Standard CMOS Setup Menu The Standard CMOS Setup Menu displays basic information about your system. Use arrow keys to highlight each item, and use <PgUp> or <PgDn> key to select the value you want in each item. Date The date format is <day> <month> <date> <year>. Time This item shows current time of your system with the format <hour> <minute> <second>. The time is calculated based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. If system is power failure, the date and time will come back to previous setup. Note PHOENIX-AWARD BIOS UTILITY 59 rBOX120-FL Series User’s Manual IDE Primary Master/Primary Slave These items identify the types of each IDE channel installed in the computer , so, IDE type is auto detection. IDE Channel 0 Master/Slave The master iteam shows CF card information only. The slave iteam shows HDD information only. 60 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual Video Select the display adapter type for your system. Halt On This item determines whether the system will halt or not, if an error is detected while powering up. No errors The system booting will halt on any errors detected. (default) Whenever BIOS detects a non-fatal error, the All errors system will stop and you will be prompted. All, But The system booting will not stop for a keyboard Keyboard error; it will stop for other errors. Press <Esc> to return to the Main Menu page. USB Device Setting PHOENIX-AWARD BIOS UTILITY 61 rBOX120-FL Series User’s Manual 3.5 Advanced BIOS Features This section allows you to configure and improve your system, to set up some system features according to your preference. 62 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual Note The BIOS default setting of the system is “Previous Setup”. It means that if the system is power failure or power loss, the system will come back to previous setup while be re-boot. PHOENIX-AWARD BIOS UTILITY 63 rBOX120-FL Series User’s Manual If you want to change the BIOS setting, please set up from “Advanced BIOS Features” (Please refer below graphic.) 64 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual Then, to select “BIOS Optimized” or “Previous Setup” under “Optimized Default Select”. (Please refer below graphic.) Further to save the selection (System will execute about 15 seconds) Finally, please shut down the system, then re-boot it, the system will come back to your changed Optimized Default Select. PHOENIX-AWARD BIOS UTILITY 65 rBOX120-FL Series User’s Manual CPU Features Scroll to this item and press <Enter> to view the CPU Feature sub menu. 66 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual Harddisk boot priority Scroll to this item and press <Enter> to view th e sub menu to decide the disk boot priority PHOENIX-AWARD BIOS UTILITY 67 rBOX120-FL Series User’s Manual Quick Power On Self Test This Option Speeds up Power on Self Test(POST) after you turn on the system power. If set as Enabled, BIOS will shorten or skip some check items during POST. The default setting is “Enabled”. Enabled Enable Quick POST Disabled Normal POST First/Second/Third Boot Device st, nd rd These items let you select the 1 2 , and 3 devices that the system will search for during its boot-up sequence. There is a wide range of options for your selection. Boot Other Device These items allows the user to enable/disable the boot device not listed on the First/Second/Third boot devices option above. The default setting is “Enabled”. Security Option This item allows you to limit access to the system and Setup, or just to Setup. The default value is “Setup”. System Setup System Setup 68 System requires correct password before booting, and also before permitting access to the Setup page. System will boot, but requires correct password before permitting access to Setup. (Default value) PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual Note To disable the security, select PASSWORD SETTING at Main Menu and then you will be asked to enter a password. Do not type anything, just press <Enter> and it will disable the security. Once the security is disabled, the system will boot and you can enter Setup freely. PHOENIX-AWARD BIOS UTILITY 69 rBOX120-FL Series User’s Manual APIC Mode APIC (Advanced Programmable Interrupt Controller) mode is enabled that provides symmetric multiprocessing (SMP) for systems. APIC Mode has been locked and cannot be modified. Note 70 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual MPS Version Control For OS This item specifies the version of the Multiprocessor Specification (MPS). Version 1.4 has extended configuration tables to improv e support for multiple PCI bus configurations and provide future expandability. Press <Esc> to return to the Main Menu page. PHOENIX-AWARD BIOS UTILITY 71 rBOX120-FL Series User’s Manual 3.6 Advanced Chipset Features This section contains completely optimized chipset ’s features on the board that you are strongly recommended to leave all items on this page at their default values unless you are very familiar with the technical specifications of your system hardware. DRAM Timing Selectable Use this item to increase the timing of the memory. This is re lated to the cooling of memory. System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h -FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The de fault value is “Disabled”. Video BIOS Cacheable This item allows you to change the Video BIOS location from ROM to RAM. Video Shadow will increase the video speed. 72 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual *** VGA Setting *** On-Chip Frame Buffer Size Use this item to set the VGA frame buffer size. Boot Type (CRT Only) This item is to select Display Device that the screen will be shown. But its default is CRT Only and cannot be modified. Panel Scaling (AUTO by default) This item shows the setting of panel scaling and operates the s caling function that the panel output can fit the screen resolution connected to the output port. Its default is AUTO and cannot be modified. Press <Esc> to return to the Main Menu page. PHOENIX-AWARD BIOS UTILITY 73 rBOX120-FL Series User’s Manual 3.7 Integrated Peripherals This section allows you to configure your OnChip IDE Device, Onboard Device, COM Ports Interface Type and USB Device Setting… 74 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual PHOENIX-AWARD BIOS UTILITY 75 rBOX120-FL Series User’s Manual OnChip IDE Device Scroll to this item and press <Enter> to view the sub menu OnChip IDE Device. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, and ormultiple sectors read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support. Press <Esc> to return to the Integrated Peripherals page. 76 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual Onboard Device Scroll to this item and press <Enter> to view the sub menu Onboard Device. SDIO/MC Controller (Enabled) Choose Enabled on the SDIO/MMC Controller Press <Esc> to return to the Integrated Peripherals page. PHOENIX-AWARD BIOS UTILITY 77 rBOX120-FL Series User’s Manual COM Port Interface Type The default setting for all COM Ports are RS232, you can change the default setting by selecting the value you want in each COM Port Type. Press <ESC> to return to the Integrated Peripherals page. 78 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual PHOENIX-AWARD BIOS UTILITY 79 rBOX120-FL Series User’s Manual USB Device Setting Scroll to this item and press <Enter> to view the sub menu USB Device Setting. Press <Esc> to return to the Integrated Peripherals page. Onboard Lan Boot ROM Use this item to enable or disable the Boot ROM function of the on board LAN chip when the system boots up. Its default is disable. 80 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual 3.8 Power Management Setup The Power Management Setup allows you to save energy of your system effectively. It will shut down the hard disk and turn OFF video display after a period of in activity. ACPI Function Advanced Configuration and Power Management (ACPI). The function is always “Enabled”. PHOENIX-AWARD BIOS UTILITY 81 rBOX120-FL Series User’s Manual 3.9 PnP/PCI Configuration Setup This section describes the configuration of PCI (Personal Computer Interconnect) bus system, which allows I/O devices to operate at speeds close to the CPU speed while communicating with other important components. This section covers very technical items that only experienced users could change default settings. Reset Configuration Data Normally, you leave this item Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup or if installing a new add -on cause the system reconfiguration a serious conflict that the operating system can not boot. Options: Enabled, Disabled. 82 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual Resources Controlled By The Award Plug and Play BIOS can automatically configure all boot and Plug and Play-compatible devices. If you select Auto, all interrupt request (IRQ), DMA assignment and Used DMA fields disappear as the BIOS automati cally assign them. The default value is “Auto”. The other option is “Manual” PHOENIX-AWARD BIOS UTILITY 83 rBOX120-FL Series User’s Manual 84 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual IRQ Resources W hen resources are controlled manually, assign each system interrupt to one of the following types in accordance with the type of devices using the in terrupt: 1. Legacy ISA Devices compliant with the original PC AT bus specification, requiring a specific interrupt (such as IRQ4 for serial port 1). 2. PCI/ISA PnP Devices compliant with the Plug and Play standard, whether designed for PCI or ISA bus ar chitecture.The default value is “PCI/ISA PnP”. PHOENIX-AWARD BIOS UTILITY 85 rBOX120-FL Series User’s Manual PCI/VGA Palette Snoop Some non-standard VGA display cards may not show colors properly. This item allows you to set whether MPEG ISA/VESA VGA Cards can work with PCI/VGA or not. W hen enabled, a PCI/VGA can work with a MPEG ISA/VESA VGA card; when disabled, a PCI/VGA cannot work with a MPEG ISA/VESA Card. ** PCI Express relative items ** 86 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual Maximum Payload Size W hen using DDR SDRAM and Buffer size selection, another consideration in designing a payload memory is the size of the buffer for data storage. Maximum Payload Size defines the maximum TLP (Transaction Layer Packet) data payload size for the device. Press <Esc> to return to the Main Menu page. PHOENIX-AWARD BIOS UTILITY 87 rBOX120-FL Series User’s Manual 3.10 PC Health Status This section supports hardware monitoring that lets you monitor those parameters for critical voltages, temperatures and fan speed of the board. Press <Esc> to return to the Main Menu page. 88 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual 3.11 Load Optimized Defaults This option allows you to load your system configuration with default values. These default settings are optimized to enable high performance features. To load CMOS SRAM with SETUP default values, please enter “Y”. If not, please enter “N”. PHOENIX-AWARD BIOS UTILITY 89 rBOX120-FL Series User’s Manual 3.12 Set Supervisor/User Password You can set a supervisor or user password, or both of them. The differences between them are: 1. Supervisor password: You can enter and change the options on the setup menu. 2. User password: You can just enter, but have no right to change the options on the setup menu. W hen you select this function, the following message will appear at the cen ter of the screen to assist you in creating a password. ENTER PASSWORD Type a maximum eight-character password, and press <Enter>. This typed password will clear previously entered password from the CMOS memory. You will be asked to confirm this password. Type this password again and press <Enter>. You may also press <Esc> to abort this selection and not enter a password. To disable the password, just press <Enter> when you are prompted to enter a password. A message will confirm the password is getting disabled. Once the password is disabled, the system will boot and you can enter Setup freely. PASSWORD DISABLED W hen a password is enabled, you have to type it every time you enter the Setup. It prevents any unauthorized persons from changing your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password every time the system reboots. This would prevent unauthorized use of your computer. You decide when the password is required for the BIOS Feat ures Setup Menu and its Security option. If the Security option is set to “System”, the password is required during booting up and entry into the Setup; if it is set as “Setup”, a prompt will only appear before entering the Setup. 90 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual PHOENIX-AWARD BIOS UTILITY 91 rBOX120-FL Series User’s Manual 3.13 Save & Exit Setup This section allows you to determine whether or not to accept your modifications. Type “Y” to quit the setup utility and save all changes into the CMOS memory. Type “N” to bring you back to the Previous Setup utility. 92 PHOENIX-AWARD BIOS UTILITY rBOX120-FL Series User’s Manual 3.14 Exit Without Saving Select this option to exit the Setup utility without saving changes you have made in this session. Type “Y”, and it will quit the Setup utility without saving your modifications and come back to Previous Setup utility. Type “N” to return to the Setup utility. ’ PHOENIX-AWARD BIOS UTILITY 93 rBOX120-FL Series User’s Manual ** Notice ** Two graphics drivers, but only one can be installed in the system. Windows XP GMA 500 driver The default setting of display output under W indows XP GMA 500 driver is LVDS port. If you only connect VGA port to install driver, please press "Ctrl+Alt+F1" to switch the display output to VGA port. Windows XP IEGD driver The default setting of display output is VGA port. 94 PHOENIX-AWARD BIOS UTILITY