DESIGNS O R N EW F D E D N MENT OMME REPLACE NOT REC D E D t N E MM Center aplease ortdatasheet, ppfull u NO RECO To request the visit www.intersil.com/products/ISL1532A S l a c ic s n /t h m c ur Te rsil.co te n .i w w contact o rw TERSIL o Data December 12, 2006 FN6369.3 88-INSheet 1-8 ISL1532A Dual Channel Fixed Gain Differential DSL Line Driver The ISL1532A is a dual channel differential amplifier designed for driving full rate ADSL2+ signals at very low power dissipation. The high drive capability of 450mA makes this driver ideal for DMT designs. It contains two pairs of wideband, high-voltage, current mode feedback amplifiers designed on Intersil’s HS30 Bipolar SOI process for low power consumption in DSL systems. The amplifiers have an internal fixed gain, which helps eliminate both feedback and gain resisitors reducing board size and cost. These drivers achieve an MTPR distortion measurement of better than 70dB, while consuming typically 5mA per DSL channel of total supply current. This supply current can be set using a resistor on the IADJ pin. Two other pins (C0 and C1) can also be used to adjust supply current to one of four pre-set modes (full-IS, 3/4-IS, 1/2-IS, and full power-down). C0 and C1 inputs are design to pull high initially. Floating these inputs will put the device in disable mode. This is contrary to EL1528 where C0 and C1 inputs pull low initially and is in the enable state when C0 and C1 pins are floated. The device is supplied in a thermally-enhanced 20 Ld HTSSOP and the small footprint (4x5mm) 24 Ld QFN packages. The ISL1532A is specified for operation over the full -40°C to +85°C temperature range. The ISL1532A provides larger output swing at heavy loads, higher slew rate, and higher bandwidth while maintaining pin-to-pin drop-in compatibility with the EL1528. The ISL1532A integrates 50k pull-up resistors on CO and C1 pins. Features • 450mA output drive capability • 44.4VP-P differential output drive into 100 • ±5V to ±15V supply operation • Internal fixed gain • MTPR of -70dB • Operates down to 2mA per amplifier supply current • Current control pins • Channel separation - 80dB @ 500kHz - 75dB @ 1MHz • Direct pin-to-pin replacement for EL1528 • Pb-free plus anneal available (RoHS compliant) Applications • Dual port ADSL line drivers • HDSL line drivers • VDSL line driver Pinouts ISL1532A (20 LD HTSSOP) TOP VIEW 20 VOUTA 21 NC 22 VS- 23 C0AB 24 C1AB ISL1532A (24 LD QFN) TOP VIEW C0AB 1 20 VS- C1AB 2 19 VOUTA VINA+ 1 19 VINA- VINA+ 3 18 VINA- VINB+ 2 18 VINB- VINB+ 4 17 VINB- GND 3 THERMAL PAD IADJ 4 17 VOUTB GND 5 16 VOUTC IADJ 6 THERMAL PAD 16 VOUTB 15 VOUTC 14 VIND- VIND+ 8 13 VIND- VIND+ 7 13 VOUTD C1CD 9 12 VOUTD C0CD 10 11 VS+ 1 NC 12 VINC+ 6 NC 11 14 VINC- VS+ 10 VINC+ 7 C0CD 9 15 VINC- C1CD 8 NC 5 *THERMAL PAD DOWN-BONDED TO GND CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL1532A For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 2 FN6369.3 December 12, 2006