EL1529 IGNS DESthe EW request full datasheet, please visit www.intersil.com/products/EL1529 R NTo O F D E END EMENT M C M A O L C P E E ED R N OT R enter at M END Sheet FN7406.1 OMData upport C om/tsc February 11, 2005 S l N O REC a ic n h c .c e il T rs r te ou contact ERSIL or www.in T N -I 8 8 1-8 Dual Channel Differential DSL Line Driver for Globespan CO Chipsets The EL1529 is to be used with Globespan's G7566-850 CO chipset for high performance long reach and high speed applications, including ADSL2, ADSL2+, G.Span, and G.Span+. The EL1529 is an integral part of the signal chain. The driver has been optimized for flat gain response and reduced harmonic distortion and noise in the bands of interest to improve the overall signal to noise in the system. These drivers achieve a total harmonic distortion (THD) measurement of typically -70dB @ 1.1MHz, while consuming typically 5mA per DSL channel of total supply current. This supply current can be set using a resistor on the IADJ pin. Two other pins (C0 & C1) can also be used to adjust supply current to one of four pre-set modes (full-IS, 3/4-IS, 1/2-IS, and full power-down). The EL1529 operates on ±5V to ±12V supplies and retains its bandwidth and linearity over the complete supply range. The device is supplied in the small footprint (4x5mm) 24-pin QFN package and is specified for operation over the full -40°C to +85°C temperature range. Pinout 20 VOUTA 21 NC 22 VS- 23 C0AB 24 C1AB EL1529 (24-PIN QFN) TOP VIEW VINA+ 1 19 VINA- VINB+ 2 18 VINB17 VOUTB GND 3 THERMAL PAD IADJ 4 16 VOUTC 13 VOUTD 1 • 450mA output drive capability • 44.1VP-P differential output drive into 100 • -85dBc THD @ 1MHz 2VP-P • High slew rate of 500V/µs • Bandwidth - 46MHz • Current control pins • Channel separation - 80dB @ 500kHz - 75dB @ 1MHz • Pb-free available (RoHS compliant) Applications • ADSL line drivers for Globespan G7566-850 CO chipsets Ordering Information PART NUMBER PACKAGE TAPE & REEL PKG. DWG. # EL1529IL 24-Pin QFN - MDP0046 EL1529IL-T7 24-Pin QFN 7” MDP0046 EL1529IL-T13 24-Pin QFN 13” MDP0046 EL1529ILZ (See Note) 24-Pin QFN (Pb-Free) - MDP0046 EL1529ILZ-T7 (See Note) 24-Pin QFN (Pb-Free) 7” MDP0046 EL1529ILZ-T13 (See Note) 24-Pin QFN (Pb-Free) 13” MDP0046 NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. NC 12 VIND+ 7 NC 11 14 VIND- VS+ 10 VINC+ 6 C0CD 9 15 VINC- C1CD 8 NC 5 Features CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2004, 2005. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. EL1529 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9001 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 2 FN7406.1 February 11, 2005