tBOX321-870-FL Series Embedded System User’s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual. Axiomtek reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd. Copyright 2015 Axiomtek Co., Ltd. All Rights Reserved July 2015, Version A2 Printed in Taiwan ii Safety Precautions Before getting started, please read the following important safety precautions. 1. User should not modify any unmentioned jumper setting without Axiomtek FAE’s instruction. Any modification without instruction might cause system to become damage 2. The tBOX321-870-FL does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. 3. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. 4. Disconnect the power cord from the tBOX321-870-FL before making any installation. Be sure both the system and the external devices are turned OFF. Sudden surge of power could ruin sensitive components. Make sure the tBOX321-870-FL is properly grounded. 5. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 6. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not spray any liquid cleaner directly onto the screen. 7. Do not leave this equipment in an uncontrolled environment where the storage temperature is below -40℃ or above 80℃. It may damage the equipment. 8. Do not open the system’s back cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body. When handling boards and components, wear a wrist-grounding strap, available from most electronic component stores. iii Classification 1. 2. 3. 4. Degree of production against electric shock: not classified Degree of protection against the ingress of water: IP40 Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide. Mode of operation: Continuous General Cleaning Tips You may need the following precautions before you begin to clean the computer. When you clean any single part or component for the computer, please read and understand the details below fully. When you need to clean the device, please rub it with a piece of dry cloth. 1. Be cautious of the tiny removable components when you use a vacuum cleaner to absorb the dirt on the floor. 2. Turn the system off before you start to clean up the component or computer. 3. Never drop the components inside the computer or get circuit board damp or wet. 4. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of cleaning. Some individuals may be allergic to the ingredients. 5. Try not to put any food, drink or cigarette around the computer. iv Cleaning Tools: Although many companies have created products to help improve the process of cleaning your computer and peripherals users can also use household items to clean their computers and peripherals. Below is a listing of items you may need or want to use while cleaning your computer or computer peripherals. Keep in mind that some components in your computer may only be able to be cleaned using a product designed for cleaning that component, if this is the case it will be mentioned in the cleaning. Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although paper towels or tissues can be used on most hardware as well, we still recommend you to rub it with a piece of cloth. Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the plastics parts. Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of a computer can be one of the best methods of cleaning a computer. Over time these items can restrict the airflow in a computer and cause circuitry to corrode. Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas in your keyboard, mouse, and other locations. Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs. NOTE: We strongly recommended that you should shut down the system before you start to clean any single components. Please follow the steps below: 1. Close all application programs 2. Close operating software 3. Turn off power switch 4. Remove all device 5. Pull out power cable v Scrap Computer Recycling If the computer equipments need the maintenance or are beyond repair, we strongly recommended that you should inform your Axiomtek distributor as soon as possible for the suitable solution. For the computers that are no longer useful or no longer working well, please contact your Axiomtek distributor for recycling and we will make the proper arrangement. Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co., Ltd. Windows® is a trademark of Microsoft Corporation. AMI® is a registered trademark of American Megatrends Inc. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation. Intel® and Atom™ are trademarks of Intel Corporation. Winbond is a trademark of Winbond Electronics Corp. Other brand names and trademarks are the properties and registered brands of their respective owners. vi Table of Contents Disclaimers .............................................................................................................. ii Safety Precautions ................................................................................................. iii Classification ......................................................................................................... iv CHAPTER 1 INTRODUCTION .............................................................................. 1 1.1 1.2 1.2.1 1.2.2 1.2.3 1.2.4 1.3 1.4 1.5 General Description ............................................................................ 1 System Specifications ........................................................................ 2 CPU .................................................................................................................... 2 System I/O ......................................................................................................... 2 System Specification ........................................................................................ 2 Driver CD Content ............................................................................................. 3 Dimensions ......................................................................................... 4 I/O Outlets............................................................................................ 5 Packing List ......................................................................................... 6 CHAPTER 2 HARDWARE INSTALLATION ...................................................... 7 2.1 2.2 Installing the swappable HDD/SSD or CFast Card............................ 7 Installing the Express Mini Card ........................................................ 8 CHAPTER 3 JUMPER SETTING & CONNECTOR ........................................... 9 3.1 3.2 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 3.3.9 3.3.10 3.3.11 3.3.12 3.3.13 SBC layout ........................................................................................... 9 Jumper Setting Summary ................................................................. 10 Connectors ........................................................................................ 11 VGA & DVI Connector .................................................................................... 11 Serial Port Connector ..................................................................................... 12 USB3.0 Stack Ports ........................................................................................ 12 LED Indicators................................................................................................. 13 DC Power Input connector ............................................................................. 13 M12 LAN Connector (LAN1~ LAN4) .............................................................. 13 Digital I/O Connector ...................................................................................... 14 SIM Card Connector ....................................................................................... 14 PCI-Express Mini Card Connector ................................................................ 15 CFast™ Socket................................................................................................ 16 USB2.0 M12 Connector .................................................................................. 17 Audio M12 Connector ..................................................................................... 17 Remote switch Connector ............................................................................. 17 CHAPTER 4 AMI BIOS SETUP UTILITY .......................................................... 19 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 Starting .............................................................................................. 19 Navigation Keys ................................................................................ 20 Main Menu ......................................................................................... 21 Advanced Menu ................................................................................ 22 Chipset Menu .................................................................................... 31 Boot Menu ......................................................................................... 34 Security Menu ................................................................................... 35 Save & Exit Menu .............................................................................. 36 APPENDIX A WATCHDOG TIMER................................................................... 37 APPENDIX B DIGITAL I/O .................................................................................. 39 vii This page is intentionally left blank. viii tBOX321-870-FL Series User’s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the tBOX321-870-FL. The Chapter 1 includes the following sections: 1.1 General Description System Specification Dimensions I/O Outlets Package List General Description ® The tBOX321-870-FL is an embedded system that supports onboard Intel Core™ i73517UE processor (up to 2.8 GHz) or i3-3217UE processor (1.60 GHz), to provide ® ® ® Windows 7 embedded, Windows 7, Windows WinCE embedded and Linux, suitable for the most endurable operation. It features fanless design with full feature I/O, supports onboard 4 or 2 GB DDR3 memory, and enhanced system dependability by built-in Watchdog Timer. Features 3rd Generation Intel® Core™ i (17W) processor onboard Intel® QM77 PCH High performance DDR3-1600 4 or 2 GB memory onboard Fanless operation Operating temperature range of -40°C ~ +70°C Isolated RS-232/422/485 and DIO Support USB 3.0 and SATA3 2 removable & lockable 2.5” SATA HDD and 1 CFast™ 3 internal PCI Express Mini Card slot and one SIM slot Lockable I/O interface and M12 LAN and USB connector Comply to fire protection of railway vehicles Europe standard PrCEN TS 45545-2 Reliable and Stable Design The tBOX321-870-FL adopts the advanced cooling system and supporting the CFast™, which makes it especially suitable for vibration environments, best for industrial automation, digital signage and gaming application. Embedded O.S. Supported ® The tBOX321-870-FL not only supports Windows 7, but also supports embedded ® OS, such as Windows 7 embedded, WinCE and Linux. For storage device, the tBOX321-870-FL supports two 2.5" SATA HDD drive bays, and one CFast™ slot. Introduction 1 tBOX321-870-FL Series User’s Manual 1.2 System Specifications 1.2.1 CPU CPU Onboard Intel® Core™ i7-3517UE processor (4M Cache, up to 2.8 GHz) Onboard Intel® Core™ i3-3217UE processor (3M Cache, 1.6 GHz) BIOS American Megatrends Inc. BIOS. “Load Optimized Default” to backup customized Setting in the BIOS flash chip to prevent from CMOS battery fail System Memory Onboard 4GB or 2GB DDR3-1600 Memory Graphics Integrated in the Intel® HD Graphics 4000 for DVI, CRT 1.2.2 System I/O Four 9-pin D-Sub male connectors, COM1~4 for isolated RS-232/422/485 One 15-pin D-Sub female connector for VGA One DVI-D female connector Two Audio connector (Mic-IN, Line-OUT)( M12 rear side)(screw front side) Four isolated M12 type 8-pin connector for 10/100/1000Base-T Two USB 2.0 connectors(M12 8 pin rear side) and Two USB 3.0 connectors(front side) One isolated 4-in/4-out DIO connector One 14~32VDC input M12 connector 1.2.3 System Specification Watchdog Timer Power Supply 14~32 VDC-in power supply (Typical as +24V), or 77~137.5 VDC-in power supply (Typical as +110V) Power Rate:14-32VDC, 1.8A@24VDC, or 77-137.5VDC, 0.5A@110VDC Operation Temperature 10% ~ 90% (non-condensation) Vibration Endurance 2 -40℃ ~ 85℃ (- 40ºF ~ 176ºF) Humidity -40℃ ~ 70℃ (- 40ºF ~ 158ºF) Storage Temperature Reset supported; 255 levels, 1~255 seconds/mintues. 3Grms w/ SSD,CFast (5 ~ 500Hz, X, Y, Z directions) Introduction tBOX321-870-FL Series User’s Manual Weight 5.06 kg (11.15 lb) without package 6.5 kg (14.33 lb) with package Dimensions 288.5mm(W) x 211.3mm(D) x 85.2mm(H) NOTE: All specifications and images are subject to change without notice. 1.2.4 Driver CD Content Chipset Driver Graphic Drivers Audio Drivers Ethernet Driver User Manual Quick Manual Introduction 3 tBOX321-870-FL Series User’s Manual 1.3 Dimensions The following diagrams show you dimensions and outlines of the tBOX321-870-FL. 4 Introduction tBOX321-870-FL Series User’s Manual 1.4 I/O Outlets The following figures show you I/O outlets on front view of the tBOX321-870-FL. Front View Front View drawing Rear View Rear View drawing Introduction 5 tBOX321-870-FL Series User’s Manual 1.5 Packing List The package bundled with your tBOX321-870-FL should contain the following items: tBOX321-870-FL System Unit x 1 tBOX321-870-FL Quick Manual x 1 CD x 1 (For Driver and User’s Manual) Screws pack Foot pad x4 Wall-mount Brackets DIO female connector HDD/SSD (optional) CFast (optional) M12 LAN cable (optional) M12 USB cable (optional) M12 Power cable (optional) M12 Audio cable (optional) M12 Power Adapter (optional) Remote switch cable (optional) Express Mini Card Module (optional) If you can not find this package or any items are missing, please contact Axiomtek distributors immediately. 6 Introduction tBOX321-870-FL Series User’s Manual CHAPTER 2 HARDWARE INSTALLATION The tBOX321-870-FL is convenient for your various hardware configurations, such as HDD TM (Hard Disk Drive), CFast card and Express Mini Card. The chapter 2 will show you how to install the hardware. 2.1 Installing the swappable HDD/SSD or CFast Card Step 1 Turn off the system, and unplug the power cord. Locate thumb screw at the front side, unlock and loosen screws. Step 2 Assembly the HDD/SSD bracket together with the SATA HDD/SSD Step 3 Slide CFast card or HDD/SSD into slot carefully Step 4 Fasten screws of HDD/CFast bracket Hardware Installation 7 tBOX321-870-FL Series User’s Manual 2.2 Installing the Express Mini Card Step 1 Turn off the system, and unplug the power cord. Step 2 Turn the system upside down to locate screws at the bottom, loosen screws to remove the bottom cover. one slot contains an internal SIM card slot which can support 2G/3G/4G modules. Step 3 Slide SIM or Mini card into slot cautionl y Step 4 Fasten screw of Express Mini Card. Step 5 Close the cover to the chassis, and fasten all screws. 8 Hardware Installation tBOX321-870-FL Series User’s Manual CHAPTER 3 JUMPER SETTING & CONNECTOR Proper jumper settings configure the tBOX321-870-FL to meet your application purpose. We are herewith listing a summary table of all jumpers and default settings for onboard devices, respectively. 3.1 SBC layout NOTE: We strongly recommended that you should not modify any unmentioned jumper setting without Axiomtek FAE’s instruction. Any modification without instruction might cause system to become damage. Jumper Setting & Connector 9 tBOX321-870-FL Series User’s Manual 3.2 Jumper Setting Summary Proper jumper settings configure the tBOX321-870-FL to meet your application purpose. We are herewith listing a summary table of all jumpers and default settings for onboard devices, respectively. Description Function Jumper Setting SJP3 Normal(Default) Clear CMOS Short 1-2 Short 2-3 You may need to use this jumper is to clear the CMOS memory if incorrect settings in the Setup Utility. 10 VDDM Settings Normal Short 1-2 (Default) Clear CMOS Short 2-3 SJP3 Jumper Setting & Connector tBOX321-870-FL Series User’s Manual 3.3 Connectors Connectors connect the CPU card with other parts of the system. Loose or improper connection might cause problems. Make sure all connectors are properly and firmly connected. 3.3.1 VGA & DVI Connector DB15 connector commonly used for the CRT Monitor. Pin Signal Pin Signal Pin Signal 1 Red 2 Green 3 Blue 4 N.C. 5 GND 6 GND 7 GND 8 GND 9 VCC 10 GND 11 N.C. 12 DDC DATA 13 Horizontal Sync 14 Vertical Sync 15 DDC CLK DVI-D connector for the digital visual interface display. Pin Signal Pin Signal 1 TX2- 2 TX2+ 3 Ground 4 No use 5 No use 6 DVI_SPD_CLK 7 DVI_SPD DATA 8 No use 9 TX1- 10 TX1+ 11 Ground 12 No use 13 No use 14 VGAVCC 15 Ground 16 FPDETECT 17 TX0- 18 TX0+ 19 Ground 20 NO use 21 No use 22 Ground 23 TXC+ 24 TXC- CN19B Jumper Setting & Connector 11 tBOX321-870-FL Series User’s Manual 3.3.2 Serial Port Connector The COM1~COM4 Port connector is a standard DB-9 connector.The pin assignment of RS232/RS-422/RS-485 is listed on the following table. If you need COM port to support RS-422 or RS-485, please selection to the BIOS items. Pin RS-232 RS-422 RS-485 1 DCD, Data carrier detect TX- Data- 2 RXD, Receive data TX+ Data+ 3 TXD, Transmit data RX+ NC 4 DTR, Data terminal ready RX- NC 5 GND, ground NC NC 6 DSR, Data set ready NC NC 7 RTS, Request to send NC NC 8 CTS, Clear to send NC NC 9 RI, Ring indicator NC NC COM 3.3.3 Pin USB3.0 Stack Ports Signal USB Port 0 Pin Signal USB Port 1 1 USB_VCC (+5V level standby power) 10 USB_VCC (+5V level standby power) 2 USB_Data2- 11 USB_Data3- 3 USB_Data2+ 12 USB_Data3+ 4 GND 13 GND 5 SSRX2- 14 SSRX3- 6 SSRX2+ 15 SSRX3+ 7 GND 16 GND 8 SSTX2- 17 SSTX3- 9 SSTX2+ 18 SSTX3+ 12 Jumper Setting & Connector tBOX321-870-FL Series User’s Manual 3.3.4 LED Indicators Status\LED ACT( L1~L4) LAN Linked Bright LINK(L1~L4) 100Mbps Blue LED 1000Mbps Yellow LED HDD HDD Active POWER Flash Power on 3.3.5 Bright DC Power Input connector The DC power input connector is M12 A-code Male 5Pin connector Pin Signal 1 VCC 2 VCC 3 System GND 4 System GND 5 Chassis GND 3.3.6 2 3 1 5 4 M12 LAN Connector (LAN1~ LAN4) The M12-8pin LAN Connector is A-Code type which can support 10/100/1000Mbps Pin 10/100 Mbps 1000 Mbps 1 -- MDI 2+ 2 -- MDI 3+ 3 -- MDI 3- 4 TX - MDI 0- 5 RX + MDI 1+ 6 TX + MDI 0+ 7 -- MDI 2 - 8 RX - MDI 1 - M12-A Code 8Pin/ Female NOTE: The M12-8pin type LAN connector pin define may difference with other device. Jumper Setting & Connector 13 tBOX321-870-FL Series User’s Manual 3.3.7 Digital I/O Connector The tBOX321-870-FL support an isolated 4-in/4-out Digital I/O (DIO) Pin Signal Pin Signal 1 EXT POWER 7 COM+ 2 IN0 8 OUT0 3 IN1 9 OUT1 4 IN2 10 OUT2 5 IN3 11 OUT3 6 GND 12 COM- NOTE: Please refer to Appendix B for more information about Digital I/O 3.3.8 SIM Card Connector The SIM Card slot is a ISO 7816 standard 6-pin connector for PCI Express Mini Card used. Pin Signal C1 SIM_PWR C2 SIM_RESET C3 SIM_CLK C5 GND C6 SIM_VPP C7 SIM_DATA LOCK 14 C3 C2 C1 C7 C6 C5 OPEN Jumper Setting & Connector tBOX321-870-FL Series User’s Manual 3.3.9 PCI-Express Mini Card Connector The PCI Express Mini Card connectors with support for a PCI Express x1 link and a USB 2.0 link. A PCI Express Mini Card can be applied to either PCI Express or USB 2.0. The USB 2.0 support will be helpful during the transition to PCI Express, because peripheral vendors will need time to design their chipsets to have the PCI Express function. During the transition, PCI Express Mini Cards can be quickly implemented by using USB 2.0. Pin Signal Pin 1 WAKE# 2 +3.3VSB 3 No use 4 GND 5 No use 6 +1.5V 7 CLKREQ# 8 9 GND 10 No use No use 11 REFCLK- 12 No use 13 REFCLK+ 14 No use 15 GND 16 No use 17 No use 18 GND 19 No use 20 +3.3VSB 21 GND 22 PERST# 23 PE_RXN4 24 +3.3VSB 25 PE_RXP4 26 GND 27 GND 28 +1.5V 29 GND 30 SMB_CLK 31 PE_TXN4 32 SMB_DATA 33 PE_TXP4 34 GND 35 GND 36 USB_D3- 37 GND 38 USB_D3+ 39 +3.3VSB 40 GND 41 +3.3VSB 42 LED_WWAN# 43 GND 44 LED_WLAN# 45 No use 46 LED_WPAN# 47 No use 48 +1.5V 49 No use 50 GND 51 No use 52 +3.3VSB Jumper Setting & Connector Signal 15 tBOX321-870-FL Series User’s Manual A PCI Express Mini Card can be applied to either PCI Express or USB 2.0. The USB 2.0 support will be helpful during the transition to PCI Express, because peripheral vendors will need time to design their chipsets to have the PCI Express function. During the transition, PCI Express Mini Cards can be quickly implemented by using USB 2.0. 3.3.10 CFast™ Socket TM The tBOX321-870-FL is equipped with a CFast socket on the solder side to TM support an SATA interface CFast disk card with DMA mode supported. The socket TM is especially designed to avoid incorrect installation of the C Fast disk card. W hen TM installing or removing the CFast disk card, please make sure the system power is off. Pin Description Pin Description 1 GND 13 N.C 2 SATA_TX+ 14 GND 3 SATA_TX- 15 N.C 4 GND 16 CFAST_LED# 5 SATA_RX- 17 N.C 6 SATA_RX+ 18 N.C 7 GND 19 N.C 8 N.C 20 +3.3V Level 9 GND 21 +3.3V Level 10 N.C 22 GND 11 N.C 23 GND 12 N.C 24 N.C 16 Jumper Setting & Connector tBOX321-870-FL Series User’s Manual 3.3.11 USB2.0 M12 Connector The USB2.0 connector is M12 A-code Male 8Pin connector Pin Signal Pin Signal 1 VCC 5 VCC 2 D- 6 D- 3 D+ 7 D+ 4 GND 8 GND Shell CHS GND 3.3.12 Audio M12 Connector The Audio connector is M12 D-code Female 5Pin connector Pin Signal 1 Line Out - L 2 Line Out - R 3 Mic In - L 4 Mic In - R 5 Audio - GND 3.3.13 Remote switch Connector Remote switch is ideal for a remote botton which can act as an ATX power on/off botton. Pin 1 Signal Description NC 2 Switch Signal 3 Ext. SW Sensor 4 GND Low Active. Act as PC’s ATX switch when external switch installed (Pin 3 Active) **Internal pull up resister did not connect to any power source Low Active. To detect external power swtich install or not. Jumper Setting & Connector ** Internal pull up resister did not connect to any power source 17 tBOX321-870-FL Series User’s Manual This page is intentionally left blank. 18 Jumper Setting & Connector tBOX321-870-FL Series User’s Manual CHAPTER 4 AMI BIOS SETUP UTILITY This chapter provides users with detailed description about how to set up basic system configuration through the AMI BIOS setup utility. 4.1 Starting To enter the setup screens, follow the steps below: 1. Turn on the computer and press the <Del> key immediately. 2. After pressing the <Delete> key, the main BIOS setup menu displays. You can access to other setup screens from the main BIOS setup menu, such as the Chipset and Power menus. AMI BIOS Setup Utility 19 tBOX321-870-FL Series User’s Manual 4.2 Navigation Keys The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include <F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, and so on. NOTE: Some of navigation keys differ from one screen to another. Hot Keys Description Left/Right The Left and Right <Arrow> keys allow you to select a setup screen. Up/Down The Up and Down <Arrow> keys allow you to select a setup screen or subscreen. + Plus/Minus The Plus and Minus <Arrow> keys allow you to change the field value of a particular setup item. Tab The <Tab> key allows you to select setup fields. F1 The <F1> key allows you to display the General Help screen. F10 The <F10> key allows you to save any changes you have made and exit Setup. Press the <F10> key to save your changes. Esc The <Esc> key allows you to discard any changes you have made and exit the Setup. Press the <Esc> key to exit the setup without saving your changes. Enter 20 The <Enter> key allows you to display or change the setup option listed for a particular setup item. The <Enter> key can also allow you to display the setup sub- screens. AMI BIOS Setup Utility tBOX321-870-FL Series User’s Manual 4.3 Main Menu System Time/Date Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format. AMI BIOS Setup Utility 21 tBOX321-870-FL Series User’s Manual 4.4 Advanced Menu The Advanced menu allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: ► ACPI Settings ► S5 RTC Wake Settings ► CPU Configuration ► SATA Configuration ► PCH-FW Configuration ► USB Configuration ► NCT6106D Super IO Configuration ► NCT6106D H/W Monitor ► WatchDog Configuration For items marked with “”, please press <Enter> for more options. 22 AMI BIOS Setup Utility tBOX321-870-FL Series User’s Manual ACPI Settings You can use this screen to select options for the ACPI Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. ACPI Sleep State Allow you to select the Advanced Configuration and Power Interface (ACPI) state to be used for system suspend. Here are the options for your selection, S1 (CPU Stop Clock) and S3 (Suspend to RAM). AMI BIOS Setup Utility 23 tBOX321-870-FL Series User’s Manual S5 RTC Wake Settings Use this option to wake on the system on the setting time. When enabled System will wake on the time specified. CPU Configuration This screen shows the CPU Configuration. 24 AMI BIOS Setup Utility tBOX321-870-FL Series User’s Manual SATA Configuration You can use this screen to select options for the SATA Configuration, and change the value of the selected option. SATA Controller(S) Use this item to enable or disable the integrated SATA controllers. (Default: Enabled) SATA Mode Use this item to choose the SATA operation mode. Here are the options for your selection, IDE Mode, AHCI Mode. SATA Controller Speed Use this item to change the SATA transfer rate Serial-ATA Port 0-2 Use this item to control the onboard SATA port. Here are the options for your selection, Enabled and Disabled. AMI BIOS Setup Utility 25 tBOX321-870-FL Series User’s Manual PCH-FW Configuration You can use this screen to confirm ME Firmware version. USB Configuration You can use this screen to select options for the USB Configuration, and change the value of the selected option. Legacy USB Support This is for supporting USB device under legacy OS such DOS, when choosing AUTO”, the system will automatically detect any USB device is plugged into the computer and enable USB legacy mode when a USB device plugged a nd disable USB legacy mode when no USB device is plugged. 26 AMI BIOS Setup Utility tBOX321-870-FL Series User’s Manual AMI BIOS Setup Utility 27 tBOX321-870-FL Series User’s Manual NCT6106D Super IO Configuration Use this screen to select options for the Super IO Configuration, and change the value of the selected option Serial Port 0-3 configuration 1. Serial port: This option used to enable or disable the serial port. 2. Device Setting: This item specifies the base I/O port address and Interrupt Request address of serial port. The port 0 Optimal setting is 3F8/IRQ4. The port 1 Optimal setting is 2F8/IRQ3. The port 2 Optimal setting is 3E8/IRQ7 The port 3 Optimal setting is 2E8/IRQ5. 2. Serial type: This option used to select RS232/422/485 function. 28 AMI BIOS Setup Utility tBOX321-870-FL Series User’s Manual AMI BIOS Setup Utility 29 tBOX321-870-FL Series User’s Manual NCT6106D H/W Monitor This screen shows the Hardware Health Configuration. WatchDog Configuration After the system stops working for a while, it can be auto-reset by the Watchdog Timer. The integrated Watchdog Timer can be set up in the system reset mode by this option. 30 AMI BIOS Setup Utility tBOX321-870-FL Series User’s Manual 4.5 Chipset Menu The Chipset menu allows users to change the advanced chipset settings. PCH-IO Configuration This screen shows the Chipset Configuration AMI BIOS Setup Utility 31 tBOX321-870-FL Series User’s Manual System Agent (SA) Configuration 1. Graphics Configuration This option allows users to change the integrated graphic device settings. Primary IGFX Boot Display Select the video device which will be activated during POST. DVMT Pre-Allocated Pre-allocated memory is the small amount of system memory made available at boot time by the system BIOS for video. Pre-allocated memory is also known as locked memory. This is because it is "locked" for video use only and as such, is invisible and unable to be used by the operating system. DVMT Total GFx Mem Allow you to allocate a fixed amount of system memory as graphics memory. Here are the options for your selection, 128MB, 256MB and Maximum DVMT. 32 AMI BIOS Setup Utility tBOX321-870-FL Series User’s Manual 2. Memory Configuration This screen shows the memory information. AMI BIOS Setup Utility 33 tBOX321-870-FL Series User’s Manual 4.6 Boot Menu The Boot menu allows users to change boot options of the system. You can select any of the items in the left frame of the screen to go to the sub menus: Setup Prompt Timeout Set the Timeout for wait press key to enter Setup Menu Bootup NumLock State Use this item to select the power-on state for the NumLock. The default setting is on. Quiet Boot Use this item to enable or disable the Quite Boot state. The default setting is disabling. Fast Boot Use this item to enable or disable the Fast Boot state. The default setting is disabling. GateA20 Active Boot Option Priorities Specifies the overall boot order from the available devices. 34 AMI BIOS Setup Utility tBOX321-870-FL Series User’s Manual 4.7 Security Menu The Security menu allows users to change the security settings for the system. Supervisor Password This item indicates whether a supervisor password has been set. If the password has been installed,『 Installed』 displays. If not, 『Not Installed』displays. User Password This item indicates whether a user password has been set. If the password has been installed, 『 Installed』 displays. If not, 『Not Installed』 displays. Change Supervisor Password Select this option and press <Enter> to access the sub menu. You can use the sub menu to change the supervisor password. Change User Password Select this option and press <Enter> to access the sub menu. You can use the sub menu to change the user password. AMI BIOS Setup Utility 35 tBOX321-870-FL Series User’s Manual 4.8 Save & Exit Menu The Exit menu allows users to load the system configuration with optimal or failsafe default values. Save Changes and Exit When you have completed the system configuration changes, select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect. Select Save Changes and Exit from the Exit menu and press <Enter>. Select Ok to save changes and exit. Discard Changes and Exit Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes and Exit from the Exit menu and press <Enter>. Select Ok to discard changes and exit. Discard Changes Use this item to abandon all changes. Load Optimal Defaults It automatically sets all Setup options to a complete set of default settings when you select this option. The Optimal settings are designed for maximum system performance, but may not work best for all computer applications. In particular, do not use the Optimal Setup options if your computer is experiencing system configuration problems. Select Load Optimal Defaults from the Exit menu and press <Enter>. Load Fail-Safe Defaults It automatically sets all Setup options to a complete set of default settings when you select this option. The Fail-Safe settings are designed for maximum system stability, but not maximum performance. Select the Fail-Safe Setup options if your computer is experiencing system configuration problems. Select Load Fail-Safe Defaults from the Exit menu and press <Enter>. Select Ok to load FailSafe defaults. 36 AMI BIOS Setup Utility tBOX321-870-FL Series User’s Manual APPENDIX A WATCHDOG TIMER What is Watchdog Timer The integrated W atchdog Timer can be set up by programming. There are 1~255 levels available. As long as the vaule of timer is set, after enabling, the countdown of the value is starting. It needs to reset or disable watchdog, otherwise auto -reset will be running when the value is counted to 0. How to Use the Watchdog Timer (Following is example to enable configuration by using debug tool) Enable WDT 1.Enable configuration -O 2E 87 -O 2E 87 2. Select Logic device: -O 2E 07 -O 2F 08 3. WDT Device Enable -O 2E 30 -O 2F 01 5. Set timer unit -O 2E F0 -O 2F 00 (00: Sec; 08: Minute) 4. Set base timer: -O 2E F1 -O 2F 0A Set Reset Time (Ex.0A:10 Sec) Disable WDT 1.Enable configuration -O 2E 87 -O 2E 87 2. Select Logic device: -O 2E 07 -O 2F 08 3. WDT Device Disable -O 2E 30 -O 2F 00 Watchdog Timer 37 tBOX321-870-FL Series User’s Manual Sample of Watchdog application Assume there is program A which needs to maintain running in a system. T he value of W atchdog Timer must be set bigger than the running time of program A. Then, after the running time of program A is finished, either to disable or to reset watchdog timer. When program A has problems to make system shut down, the system can be rebooted by W atchdog timer when the value of watchdog timer is countdowned to 0 . The below flowchart can be referred to edit program A 38 Watchdog Timer tBOX321-870-FL Series User’s Manual APPENDIX B DIGITAL I/O Digital I/O Specification Digital Input: Input channels: 4, sink/source type Input voltage: 0 to 30VDC at 25Hz Input level for dry contacts: Logic level 0: close to ground Logic level 1: open Input level for wet contacts: Logic level 1: +/-3VDC max. Logic level 0: +/- 10VDC min. to +/-30VDC max. (source to digital input) Digital output: output channels: 4, sink type output current: 200mA max. per channel on-state voltage:12~ 24VDC nominal max. voltage on COM+: 30VDC Digital I/O Software Programming I2C to GPIO PCA9554PW GPIO Group0[3:0] is Output, Group0[7:4] is Intput. I2C address: 0b0100100x. Registers: Register 0: Input Group0 register. Register 2: Output Group0 register. Digital I/O 39 tBOX321-870-FL Series User’s Manual Digital Input Wiring DRY contact Logic level 0: close to ground Logic level 1: open EXT_POWER SW1 XIN1 SW2 XIN2 SW3 XIN3 SW4 XIN4 DIO_GND WET contact Logic level 1: +/-3VDC max. Logic level 0: +/- 10VDC min. to +/-30VDC max + Vdc Max:+30V EXT_POWER SW1 XIN1 SW2 XIN2 SW3 XIN3 SW4 XIN4 DIO_GND Digital Output Wiring XOUTCOM+ XOUT1 XOUT2 XOUT3 XOUT4 Loading Loading I max=200mA Sink type Loading Loading XOUTCOM- Vdc + Max:+30V 40 Digital I/O