GOT710-837 Railway 10.4” SVGA TFT Slim PANEL PC User’s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual. Axiomtek reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd. CAUTION If you replace wrong batteries, it causes the danger of explosion. It is recommended by the manufacturer that you follow the manufacturer’s instructions to only replace the same or equivalent type of battery, and dispose of used ones. Copyright 2015Axiomtek Co., Ltd. All Rights Reserved Mar 2015, Version A1 Printed in Taiwan ii Safety Precautions Before getting started, read the following important cautions. 1. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. 2. Disconnect the power cords from the NA-550 Series before making any installation. Be sure both the system and the external devices are turned OFF. Sudden surge of power could ruin sensitive components. Make sure the NA-550 Series is properly grounded. 3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body. When handling boards and components, wear a wrist-grounding strap, available from most electronic component stores. Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co., Ltd. ® Windows is a trademark of Microsoft Corporation. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation. ® ® Intel and Pentium are trademarks of Intel Corporation. AMI is trademark of American Megatrend Inc. Other brand names and trademarks are the properties and registered brands of their respective owners. iii Table of Contents Disclaimers ..................................................................................................... ii Safety Precautions ........................................................................................ iii Chapter 1 Introduction ............................................. 1 1.1 General Description ............................................................................ 1 1.2 Specifications ...................................................................................... 2 1.3 Dimensions and Outlines ................................................................... 4 1.4 I/O Outlets ............................................................................................ 5 1.5 Packing List ......................................................................................... 6 Chapter 2 Hardware and Installation ...................... 7 2.1 Open back cover ................................................................................. 8 2.2 Serial Ports Interface .......................................................................... 8 2.3 USB Ports ............................................................................................ 9 2.4 Ethernet................................................................................................ 9 2.5 DIO ...................................................................................................... 10 2.6 Audio .................................................................................................. 10 2.7 CANBUS connector (CAN1) ............................................................. 11 2.8 DC Power connector (CN7) .............................................................. 11 2.9 Mini card Installation......................................................................... 12 2.9.1 2.9.2 Wireless LAN Card Installation ................................................................. 12 mSATA Card Installation ............................................................................ 13 2.10 System jumper setting ...................................................................... 14 2.11 System Panel Header ........................................................................ 15 Chapter 3 AMI BIOS Setup Utility .......................... 17 3.1 Starting ............................................................................................... 17 3.2 Menu Bar ............................................................................................ 18 3.3 Navigation Keys ................................................................................ 18 3.4 Main Menu.......................................................................................... 19 3.5 Advanced Menu ................................................................................. 20 3.6 Chipset Menu ..................................................................................... 25 3.7 Security Menu .................................................................................... 28 3.8 Boot Menu.......................................................................................... 29 3.9 Exit Menu ........................................................................................... 30 iv Chapter 4 Drivers Installation .............................. 31 4.1 System ............................................................................................... 31 4.2 Touch Screen ..................................................................................... 31 4.3 Embedded O.S. .................................................................................. 34 v This page is intentionally left blank. vi GOT710-837 User’s Manual Chapter 1 Introduction This chapter contains general information and detailed specifications of the GOT710-837. Chapter 1 includes the following sections: 1.1 General Description Specification Dimensions I/O Outlets Package List General Description GOT710-837 is used to keep the train driver informed about the status of the train’s functions. Its design allows it to be deployed in environment with an extended temperature (-25°C ~ 70°C) and it also complies with the EMC, shock and vibration test requirements of European standard EN50155 for railway applications. GOT710-837 is equipped with 10.4" TFT ruggedized touch panel computer and all lockable connectors are perfect choice for Human Machine Interface (HMI) in railway environments. The 10.4" railway touch panel PC includes a comprehensive feature set with one CAN Bus, DIO, audio, two Ethernet ports, USB ports and RS-232/422/485. Railway application-EN50155 certificated Railway power module design support 10ms interruption, EMI EN55022 CLASS A filter, over/short current protection for its railway application. Sunlight readable design Its sunlight readable technology with LED tech high brightness 1000 nits color display allows the screen legible even strong sunlight. Powerful computing: Intel® Atom Bay Trail processors ® GOT710-837 features Intel Atom processors that offers reliable and stable performance and rugged environment. Introduction 1 GOT710-837 User’s Manual 1.2 Specifications Main CPU Board CPU ® Intel Atom TM E3827 1.75GHz / E3845 1.91GHz processor onboard System Memory DDR3 4 GB (default) or 8 GB memory onboard BIOS America Megatrends Inc BIOS I/O System Standard I/O 2 x RS-232/422/485 with isolated 1.5KV (M12, A-coded) 2 x Gigabit LAN with isolated 1.5KV (M12, X-coded) 2 x USB 2.0 (M12, A-coded) 1 x DIO (6 input/2 output) with isolated 1.5KV (Phoenix type) 1 x CAN bus with isolated 1.5KV (D-sub) Ethernet 2 x RJ45 for Giga Ethernet Audio 1 x Audio: Line out, Line in, speaker out (D-sub) Expansion 2 x PCIe Mini Card slots Storage 16 GB flash onboard 1 x mSATA Power connector 1 x DC for power input with isolated 1.5KV (M12, A-coded) 2 Introduction GOT710-837 User’s Manual System Specification 10.4” SVGA(800 X 600)LCD 5 wired resistive Touch or glass IP65/NEMA4 aluminum front bezel IP65 aluminum front bezel Net Weight Dimension (Main Body Size) 2.4 Kgs (12.35 lb) 310 x 51.5 x 214 mm Operation Temperature -25℃ to 70℃ Relative Humidity 10% to 95% @ 40℃, Non-Condensing Power Input 14.4V to 40VDC or 66V to 154VDC NOTE All specifications and images are subject to change without notice. Introduction 3 GOT710-837 User’s Manual 1.3 Dimensions and Outlines The following diagrams show the dimensions and outlines of GOT710-837. 4 Introduction GOT710-837 User’s Manual 1.4 I/O Outlets Please refer to the following illustration for I/O locations of the GOT710-837. 1 2 3 4 5 6 No Introduction 7 8 9 Function 1 DC for power input with isolated 1.5KV 2 CAN Bus with isolated 1.5KV 3 Audio (Line out, Line in, speaker out) 4 DIO (6 input/2 output with isolated 1.5KV) 5 USB 2.0 x 2(M12, A-coded) 6 COM 2 (RS-232/422/485 with isolated 1.5KV) 7 COM 1 (RS-232/422/485 with isolated 1.5KV) 8 LAN 2 (Gigabit LAN with isolated 1.5KV) 9 LAN 1 (Gigabit LAN with isolated 1.5KV) 5 GOT710-837 User’s Manual 1.5 Packing List When you receive the GOT710-837, the bundled package should contain the following items: GOT710-837 unit x 1 Driver CD x1 Power cable x 1 Phoenix Connector x 1 If you can not find the package or any items are missing, please contact Axiomtek distributors immediately. 6 Introduction GOT710-837 User’s Manual Chapter 2 Hardware and Installation The GOT710-837 provides rich I/O ports and flexible expansions for you to meet different demand. The chapter will show you how to install the hardware. It includes: Open back cover Serial Ports USB Ports Ethernet DIO Audio CANBus DC Power Mini card System jumper setting System Panel Header Hardware and Installation 7 GOT710-837 User’s Manual 2.1 Open back cover This section tells users how to open back cover. Please follow the steps below. Step 1 Unscrew 10 screws on the back cover. Please refer the photo below. 2.2 Serial Ports Interface This system supports RS-232/422/485 isolated 1.5KV on COM1~COM2 ports. The pin assignments are listed in table below. If you need to adjust these COM ports to work as RS-232/422/485, please refer to BIOS setting in section 3.5. Pin Definition 1 NDCD1 2 NRX1 3 NTX1 4 NDTR1 5 NDSR1 6 NRTS1 7 NCTS1 8 ISO1_GND 9 ISO1_GND 8 Hardware and Installation GOT710-837 User’s Manual 2.3 USB Ports This system supports two USB ports. The pin assignments are listed in table below. Pin Definition 1 USB1_PWR 2 USB_DN1_C 3 USB_DP1_C 4 GND 5 USB2_PWR 6 USB_DN2_C 7 USB_DP2_C 8 GND 2.4 Ethernet The GOT710-837 is equipped with two high performance plug and play Ethernet interfaces with X-coded which are fully compliant with the IEEE 802.3 standard. Connection can be established by plugging one end of the Ethernet cable into this RJ-45 connector and the other end to a 1000/100/10-Base-T hub with isolated 1.5KV. Pin CN4_LAN1 Definition Pin CN4_LAN1 Definition 1 LAN1_MDOP0 1 LAN2_MDOP0 2 LAN1_MDON0 2 LAN2_MDON0 3 LAN1_MDOP1 3 LAN2_MDOP1 4 LAN1_MDON1 4 LAN2_MDON1 5 LAN1_MDOP3 5 LAN2_MDOP3 6 LAN1_MDON3 6 LAN2_MDON3 7 LAN1_MDON2 7 LAN2_MDON2 8 LAN1_MDOP2 8 LAN2_MDOP2 9 GND_LAN 9 GND_LAN Hardware and Installation 9 GOT710-837 User’s Manual 2.5 DIO This system supports one DIO (6 input and 2 output) with isolated 1.5KV. The pin assignments are listed in table below. Pin Definition 1 XOUTCOM+ 2 XIN4 3 XIN5 4 XOUT0 5 XOUT1 6 XOUTCOM 7 EXT_POWER 8 XIN0 9 XIN1 10 XIN2 11 XIN3 12 DIO_GND 2.6 Audio This system supports one Audio (Line out, Line in, speaker out) with isolated 1.5KV. The pin assignments are listed in table below. Pin Definition 1 SPEK_OUTA+ 2 SPEK_OUTA- 3 AUDIO_GND 4 AUDIO_OUT_L 5 AUDIO_OUT_R 6 NA 7 FRONT-JD 8 AUDIO_GND 9 AUDIO_LIN_IN_L 10 AUDIO_LIN_IN_R 11 BUZZER+ 12 MIC-JD 13 MIC-JD 14 MIC_IN 15 AUDIO_GND 10 Hardware and Installation GOT710-837 User’s Manual 2.7 CANBUS connector (CAN1) This system supports one CANBus with isolated 1.5KV. The pin assignments are listed in table below. Pin Definition 1 2 3 4 5 6 7 8 9 NA 2.8 CAN_LO ISO3_GND NA NA ISO3_GND CAN_HO NA NA DC Power connector (CN7) The system supports one DC for power input with isolated 1.5KV. The pin assignments are listed in table below. Pin Definition 1 PWR_V+ 2 PWR_V+ 3 PWR_V- 4 PWR_V- 5 ACC Hardware and Installation 11 GOT710-837 User’s Manual 2.9 Mini card Installation 2.9.1 Wireless LAN Card Installation The GOT710-837 provides two Mini card slots for user to install wireless LAN cards. You can choose either slot 1 or slot 2 to install the wireless LAN card and refer to the following. Step 1 Open the back cover and find out the mini-card slot on main board. Step 2 Insert the wireless LAN card to the slot. Screw it firmly on the slot. Step 3 12 There are two connectors on wireless LAN card. One is MAIN, and the other is auxiliary. Connect antenna cable to MAIN connector on wireless LAN card. Hardware and Installation GOT710-837 User’s Manual 2.9.2 mSATA Card Installation The GOT710-837 provides one Mini card slot for user to install mSATA. Please choose the slot 2 when installing the mSATA card and refer to the following instructions and illustration: Step 1 Open the back cover and find out the mini-card slot on main board. Step 2 Insert the mSATA card to the slot 2. Screw it firmly on the slot. Hardware and Installation 13 GOT710-837 User’s Manual 2.10 System jumper setting Please see the jumper setting as below for your requirement. Jumper ★ Default Setting Jumper Setting JP1 ★LVDS Panel Power : 3.3V Short 1-2 LVDS Panel Power : 5V Short 3-4 JP3 ★ COM5 normal mode COM5 pin1 with power :+5V JP4 JP5 JP6 JP7 Short 1-2 Panel backlight control DC mode Short 3-4 ★ Normal 14 Short 1-2 Clear CMOS Short 2-3 ★Internal Storage Short 1-2 External Conn Short 2-3 ★PCIe device ★AT mode ATX mode JP9 Short 2-3 ★ Panel backlight control PWM mode mSATA device JP8 Short 1-2 Short 1-2 Short 2-3 Short 1-2 Short 2-3 Touch Controller 4,8 WIRE Short 1-2 ★ Touch Controller 5 WIRE Short 2-3 Hardware and Installation GOT710-837 User’s Manual 2.11 System Panel Header Please see the panel header as below table. Pin Definition 1 NA 2 NA 3 Buzzer - 4 Buzzer + 5 RESET# 6 GND 7 HDLED- 8 HDLED+ 9 NA Jumper ★ Default Setting Jumper Setting JP1 ★MCU I2C Power : 3.3V Short 1-2 MCU I2C Power : 5V Short 3-4 JP3 ★Buzzer Power : 5V Buzzer Power : 12V Hardware and Installation Short 1-2 Short 2-3 15 GOT710-837 User’s Manual This page is intentionally left blank. 16 Hardware and Installation GOT710-837 User’s Manual Chapter 3 AMI BIOS Setup Utility The AMI UEFI BIOS provides users with a built-in setup program to modify basic system configuration. All configured parameters are stored in a flash chip to save the setup information whenever the power is turned off. This chapter provides users with detailed description about how to set up basic system configuration through the AMI BIOS setup utility. 3.1 Starting To enter the setup screens, follow the steps below: 1. 2. Turn on the computer and press <F2> or <Del> during the Power On Self Test (POST) to enter BIOS setup, otherwise, POST will continue with its test routines. After you press the <Del> key, the main BIOS setup menu displays. You can access the other setup screens from the main BIOS setup menu, such as the Advanced and Chipset menus. NOTE If your computer cannot boot after making and saving system changes with BIOS setup, you can restore BIOS optimal defaults by setting CLRCMOS1 (see section 2.3.1). If you wish to enter BIOS setup after POST, restart the system by pressing <Ctrl>+<Alt>+ <Delete>, or by pressing the reset button on the system chassis. You may also restart by turning the system off and then back on. It is strongly recommended that you should avoid changing the chipset’s defaults. Both AMI and your system manufacturer have carefully set up these defaults that provide the best performance and reliability. NOTE Because the BIOS setup software is constantly being updated, the following setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen. AMI BIOS Setup Utility 17 GOT710-837 User’s Manual 3.2 Menu Bar The top of the screen has a menu bar with the following selections: Menu Bar Description Main To set up the system time/date information. Advanced To set up the advanced BIOS features. H/W Monitor To display current hardware status. Boot To set up the default system device to locate and load the operating system. Security To set up the security features. Exit To exit the current screen or the BIOS setup utility. Use <> key or <> key to choose among the selections on the menu bar, and then press <Enter> to get into the sub screen. You can also use the mouse to click your required item. 3.3 Navigation Keys The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include <F1>, <F7>, <Enter>, <ESC>, <Arrow> keys, and so on. NOTE Some of the navigation keys differ from one screen to another. Please check the following table for the function description of each navigation key. Hot Keys Description Left/Right The Left and Right <Arrow> keys allow you to select a setup screen. Up/Down The Up and Down <Arrow> keys allow you to select a setup screen or sub-screen. + Plus/Minus The Plus and Minus <Arrow> keys allow you to change the field value of a particular setup item. Enter The <Enter> key allows you to display or change the setup option listed for a particular setup item. The <Enter> key can also allow you to display the setup sub- screens. F1 The <F1> key allows you to display the General Help screen. F7 Discard changes. F9 The <F9> key allows you to load optimal default values for all the settings. F10 The <F10> key allows you to save any changes you have made and exit Setup. Press the <F10> key to save your changes. Esc The <Esc> key allows you to discard any changes you have made and exit the Setup. Press the <Esc> key to exit the setup without saving your changes. 18 AMI BIOS Setup Utility GOT710-837 User’s Manual 3.4 Main Menu When you first enter the setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. System Time/Date can be set up as described below. The Main BIOS setup screen is shown below. BIOS Information Display the auto-detected BIOS information. System Date/Time Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format. AMI BIOS Setup Utility 19 GOT710-837 User’s Manual 3.5 Advanced Menu The Advanced menu also allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: NCT6106D Super IO Configuration NCT6106D H/W Monitor CPU Configuration IDE Configuration Miscellaneous Configuration CSM Configuration USB Configuration For items marked with “”, please press <Enter> for more options. NOTE Setting wrong values in this section may cause the system to malfunction. 20 AMI BIOS Setup Utility GOT710-837 User’s Manual NCT6106D Super IO Configuration Use this screen to select options for the Super IO Configuration, and change the value of the selected option Serial Port 1-2 configuration 1. Serial port: This option used to enable or disable the serial port. 2. Device Setting: This item specifies the base I/O port address and Interrupt Request address of serial port. The port 1 Optimal setting is 3F8/IRQ4. The port 2 Optimal setting is 2F8/IRQ3 3. Serial type: This option used to select RS232/422/485 function. AMI BIOS Setup Utility 21 GOT710-837 User’s Manual NCT6106D H/W Monitor This screen shows the Hardware Health Configuration. CPU Configuration This screen shows the CPU Configuration and intel virtualization technology enable/disable selected 22 AMI BIOS Setup Utility GOT710-837 User’s Manual IDE Configuration You can use this screen to select options for the SATA Configuration, and change the value of the selected option. SATA Mode Use this item to choose the SATA operation mode. Here are the options for your selection, IDE Mode, AHCI Mode. Miscellaneous Configuration Use this screen to select options for different OS, Windows8.X, Android, Windows7. AMI BIOS Setup Utility 23 GOT710-837 User’s Manual CSM Configuration Enable is Legacy mode, Disable is UEFI mode. USB Configuration Display USB Device Configuration 24 AMI BIOS Setup Utility GOT710-837 User’s Manual 3.6 Chipset Menu In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority. North Bridge This screen shows the North Bridge memory information. You can use this screen to select options for the LVDS Configuration. AMI BIOS Setup Utility 25 GOT710-837 User’s Manual 26 South Bridge AMI BIOS Setup Utility GOT710-837 User’s Manual USB Configuration Only support USB2.0(EHCI). AMI BIOS Setup Utility 27 GOT710-837 User’s Manual 3.7 Security Menu In this section, you may set, change or clear the supervisor/user password for the system. 28 AMI BIOS Setup Utility GOT710-837 User’s Manual 3.8 Boot Menu The Boot menu allows users to change boot options of the system. You can select any of the items in the left frame of the screen to go to the sub menus: Setup Prompt Timeout Set the Timeout for wait press key to enter Setup Menu Bootup NumLock State Use this item to select the power-on state for the NumLock. The default setting is on. Quiet Boot Use this item to enable or disable the Quite Boot state. The default setting is disable Legacy Pxe OPROM Use this item to enable or disable the Preboot Execution Environment. The default setting is disable. Boot Option Priorities Specifies the overall boot order from the available devices. AMI BIOS Setup Utility 29 GOT710-837 User’s Manual 3.9 Exit Menu NOTE Load default before updating g TXE firmware and restart. 30 AMI BIOS Setup Utility GOT710-837 User’s Manual Chapter 4 Drivers Installation 4.1 System GOT710-837 supports Windows 7and WES 7. To facilitate the installation of system driver, please carefully read the instructions in this chapter before start installing. Step 1 Insert Driver CD and select the “\Drivers”. Step 2 Select all files and follow the installing procedure. 4.2 Touch Screen The GOT710-837 uses the 5-wire analog resistive. There are the specification and driver installation which are listed below. Specification Touch Screen 5-wire Analog Resistive type Touch Screen Controller PenMount 6500 USB Touch Screen Controller IC Communications USB interface Baud Rate 19200 baud rate fixed Resolution 1024 X 1024 Drivers Installation 31 GOT710-837 User’s Manual Driver Installation- Windows 7 The GOT710-837 provides a touch screen driver that users can install it under the operating system Windows 7. To facilitate installation of the touch screen driver, you should read the instructions in this chapter carefully before you attempt installation. Step 1 Insert Driver CD and follow the path to select the “\Drivers\Step 6. Touch”. Step 2 Follow the installing procedure and press OK. Step 3 Click Start menu and select “PenMount Utilities”; and then, a “PenMount Control Panel” pops out. 32 Drivers Installation GOT710-837 User’s Manual Step 4 Select the “Standard Calibrate” tab. Step 5 Calibrations: To adjust the display with touch panel, click “Calibration” and follow the calibrate point to do calibration; there are five points on screen for calibration. Step 6 Press OK. Drivers Installation 33 GOT710-837 User’s Manual 4.3 Embedded O.S. The GOT710-837 provides the Windows 7 Embedded. The O.S. is supported devices which are listed below. WES 7 Here are supported onboard devices: Onboard Multi I/O SATA HDD USB PS2 Keyboard and mouse CRT/LCD display 10/100/1000 base-T Ethernet Onboard Audio Touch Screen PenMount Touch screen Before you can use and calibrate it, here is what you should do: 1. Set up Penmount touch device driver by executing C:\Penmount\ Windows 2000-XP V5.0\setup.exe. When the installation is finished, an icon “PM” appears on the Taskbar. 2. Calibrate Penmount touch by clicking on the “PM” icon, and the go on the calibration. 3. Restart the computer. 34 Drivers Installation