DATASHEET

X28C010, X28HT010
ESIGNS
R N E W D NT
O
F
D
E
D
N
EM E
COMME
RE PL AC
D
E
N OT R E
r at
D
N
OMME
ort Cente sc
uppSheet
S
l
NO R E C
a
/t
ic
Data
m
n
o
h
tersil.c
our Tec
contact ERSIL or www.in
T
1-888-IN
February 12, 2007
5V, Byte Alterable EEPROM
Features
The Intersil X28C010/X28HT010 is a 128K x 8 EEPROM,
fabricated with Intersil's proprietary, high performance,
floating gate CMOS technology. Like all Intersil
programmable non-volatile memories, the
X28C010/X28HT010 is a 5V only device. The
X28C010/X28HT010 features the JEDEC approved pin out
for byte-wide memories, compatible with industry standard
EEPROMs.
• Access time: 120ns
FN8105.1
• Simple byte and page write
- Single 5V supply
- No external high voltages or VPP control
circuits
- Self-timed
• No erase before write
• No complex programming algorithms
• No overerase problem
The X28C010/X28HT010 supports a 256-byte page write
operation, effectively providing a 19µs/byte write cycle and
enabling the entire memory to be typically written in less
than 2.5 seconds. The X28C010/X28HT010 also features
DATA Polling and Toggle Bit Polling, system software
support schemes used to indicate the early completion of a
write cycle. In addition, the X28C010/X28HT010 supports
Software Data Protection option.
• Low power CMOS
- Active: 50mA
- Standby: 500µA
• Software data protection
- Protects data against system level inadvertent writes
• High speed page write capability
• Highly reliable Direct Write™ cell
- Endurance: 100,000 write cycles
- Data retention: 100 years
Intersil EEPROMs are designed and tested for applications
requiring extended endurance. Data retention is specified to
be greater than 100 years.
• Early end of write detection
- DATA polling
- Toggle bit polling
• X28HT010 is fuly functional @ +175°C
Pinouts
32
1
31
VCC
WE
A1
13
A0
14
CE
I/O1
VSS
I/O4
I/O7
16
18
20
23
24
A3
11
OE
A10
26
25
A5
2
3
30
NC
A2
12
A12
A7
4
29
5
28
A14
A13
A4
10
A6
A5
6
27
7
26
A4
A3
8
A2
A1
10
23
11
22
A0
I/O0
12
21
13
20
I/O1
I/O2
14
19
15
18
I/O5
I/O4
VSS
16
17
I/O3
9
25
24
A8
A9
8
A11
OE
6
A6
A12
9
7
5
4
A10
CE
X28C010
(Bottom View)
A7
A15
A
16
NC
2
NC
3
VCC
NC
36
34
NC
1
WE
35
A11
27
A9
28
A8
29
A 13
30
NC
32
A 14
31
NC
33
4 3 2
A7
A6
A5
A4
A3
A2
A1
A0
I/O 0
WE
NC
A12
A15
A16
NC
VCC
I/O0
I/O2
I/O 3
I/O5
I/O6
15
17
19
21
22
A16
A15
X28C010
EXTENDED LCC
32 31 30
1
5
6
7
8
9
10
11
12
13
X28C010
(Top View)
29
28
27
26
25
24
23
22
21
A14
A13
A8
A9
A11
OE
A10
CE
I/O7
14 15 16 17 18 19 20
I/O4
I/O5
I/O6
NC
PGA
I/O1
I/O2
VSS
I/O3
CERDIP
Flat Pack
SOIC (R)
I/O7
I/O6
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2005, 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
X28C010, X28HT010
Ordering Information
PART NUMBER
PART MARKING
ACCESS
TIME
TEMP RANGE
(°C)
PACKAGE
PKG. DWG #
X28C010D-12
X28C010D-12
120ns
0 to +70
32-Ld Cerdip
F32.6
X28C010D-15
X28C010D-15
150ns
0 to +70
32-Ld Cerdip
F32.6
X28C010DI
X28C010DI
-
-40 to +85
32-Ld Cerdip
F32.6
X28C010DI-12
X28C010DI-12
120ns
-40 to +85
32-Ld Cerdip
F32.6
X28C010DI-15
X28C010DI-15
150ns
-40 to +85
32-Ld Cerdip
F32.6
X28C010DM
X28C010DM
-
-55 to +125
32-Ld Cerdip
F32.6
X28C010DM-12
X28C010DM-12
120ns
-55 to +125
32-Ld Cerdip
F32.6
X28C010DM-15
X28C010DM-15
150ns
-55 to +125
32-Ld Cerdip
F32.6
X28C010DMB-12
C X28C010DMB-12
120ns
MIL-STD-883
32-Ld Cerdip
F32.6
X28C010DMB-15
C X28C010DMB-15
150ns
MIL-STD-883
32-Ld Cerdip
F32.6
X28C010DMB-20
C X28C010DMB-20
200ns
MIL-STD-883
32-Ld Cerdip
X28C010FI-12
X28C010FI-12
120ns
-40 to +85
32-Ld Flat Pack
X28C010FI-15
X28C010FI-15
150ns
-40 to +85
32-Ld Flat Pack
X28C010FI-20
X28C010FI-20
200ns
-40 to +85
32-Ld Flat Pack
X28C010FM
X28C010FM
-
-55 to +125
32-Ld Flat Pack
X28C010FM-12
X28C010FM-12
120ns
-55 to +125
32-Ld Flat Pack
X28C010FMB-12
C X28C010FMB-12
120ns
MIL-STD-883
32-Ld Flat Pack
X28C010FMB-15
C X28C010FMB-15
150ns
MIL-STD-883
32-Ld Flat Pack
X28C010K-25
X28C010K-25
250ns
0 to +70
36-Ld Pin Grid Array
G36.760x760A
X28C010KM-12
X28C010KM-12
120ns
-55 to +125
36-Ld Pin Grid Array
G36.760x760A
X28C010KM-25
X28C010KM-25
250ns
-55 to +125
36-Ld Pin Grid Array
G36.760x760A
X28C010KMB-12
C X28C010KMB-12
120ns
MIL-STD-883
36-Ld Pin Grid Array
G36.760x760A
X28C010KMB-15
C X28C010KMB-15
150ns
MIL-STD-883
36-Ld Pin Grid Array
G36.760x760A
X28C010NM-12
X28C010NM-12
120ns
-55 to +125
32-Ld Extended LCC
X28C010NM-15
X28C010NM-15
150ns
-55 to +125
32-Ld Extended LCC
X28C010NMB-12
C X28C010NMB-12
120ns
MIL-STD-883
32-Ld Extended LCC
X28C010NMB-15
C X28C010NMB-15
150ns
MIL-STD-883
32-Ld Extended LCC
X28C010RI-12
X28C010RI-12
120ns
-40 to +85
32-Ld Ceramic SOIC (Gull Wing)
X28C010RI-20
X28C010RI-20
200ns
-40 to +85
32-Ld Ceramic SOIC (Gull Wing)
X28C010RI-20T1
X28C010RI-20
200ns
-40 to +85
32-Ld Ceramic SOIC (Gull Wing)
X28C010RM-15
X28C010RM-15
150ns
-55 to +125
32-Ld Ceramic SOIC (Gull Wing)
X28C010RMB-25
C X28C010RMB-25
250ns
MIL-STD-883
32-Ld Ceramic SOIC (Gull Wing)
200ns
-40 to +175
X28HT010W
2
Wafer
FN8105.1
February 12, 2007
X28C010, X28HT010
Block Diagram
A8-A16
X Buffers
Latches and
Decoder
EEPROM
Array
A0-A7
Y Buffers
Latches and
Decoder
I/O Buffers
and Latches
CE
OE
WE
1Mbit
Control
Logic and
Timing
I/O0-I/O7
Data Inputs/Outputs
VCC
VSS
Pin Descriptions
Pin Names
Addresses (A0-A16)
The Address inputs select an 8-bit memory location during a
read or write operation.
SYMBOL
DESCRIPTION
A0-A16
Address Inputs
Chip Enable (CE)
I/O0-I/O7
Data Input/Output
WE
Write Enable
CE
Chip Enable
OE
Output Enable
VCC
+5V
VSS
Ground
NC
No Connect
VBB*
-3V
The Chip Enable input must be LOW to enable all read/write
operations. When CE is HIGH, power consumption is
reduced.
Output Enable (OE)
The Output Enable input controls the data output buffers,
and is used to initiate read operations.
Data In/Data Out (I/O0-I/O7)
Data is written to or read from the X28C010/X28HT010
through the I/O pins.
*VBB applies to X28HT010 only.
Write Enable (WE)
Device Operation
The Write Enable input controls the writing of data to the
X28C010/X28HT010.
Read
Back Bias Voltage (VBB) (X28HT010 only)
It is required to provide -3V on pin 1. This negative voltage
improves higher temperature functionality.
Read operations are initiated by both OE and CE LOW. The
read operation is terminated by either CE or OE returning
HIGH. This two line control architecture eliminates bus
contention in a system environment. The data bus will be in
a high impedance state when either OE or CE is HIGH.
Write
Write operations are initiated when both CE and WE are
LOW and OE is HIGH. The X28C010/X28HT010 supports
both a CE and WE controlled write cycle. That is, the
address is latched by the falling edge of either CE or WE,
whichever occurs last. Similarly, the data is latched internally
by the rising edge of either CE or WE, whichever occurs first.
A byte write operation, once initiated, will automatically
continue to completion, typically within 5ms.
3
FN8105.1
February 12, 2007
X28C010, X28HT010
Page Write Operation
The page write feature of the X28C010/X28HT010 allows
the entire memory to be written in 5 seconds. Page write
allows two to two hundred fifty-six bytes of data to be
consecutively written to the X28C010/X28HT010 prior to the
commencement of the internal programming cycle. The host
can fetch data from another device within the system during
a page write operation (change the source address), but the
page address (A8 through A16) for each subsequent valid
write cycle to the part during this operation must be the same
as the initial page address.
DATA Polling (I/O7)
The page write mode can be initiated during any write
operation. Following the initial byte write cycle, the host can
write an additional one to two hundred fifty six bytes in the
same manner as the first byte was written. Each successive
byte load cycle, started by the WE HIGH to LOW transition,
must begin within 100µs of the falling edge of the preceding
WE. If a subsequent WE HIGH to LOW transition is not
detected within 100µs, the internal automatic programming
cycle will commence. There is no page write window
limitation. Effectively the page write window is infinitely wide,
so long as the host continues to access the device within the
byte load cycle time of 100µs.
The X28C010/X28HT010 features DATA Polling as a
method to indicate to the host system that the byte write or
page write cycle has completed. DATA Polling allows a
simple bit test operation to determine the status of the
X28C010/X28HT010, eliminating additional interrupt inputs
or external hardware. During the internal programming cycle,
any attempt to read the last byte written will produce the
complement of that data on I/O7 (i.e., write data = 0xxx xxxx,
read data = 1xxx xxxx). Once the programming cycle is
complete, I/O7 will reflect true data. Note: If the
X28C010/X28HT010 is in the protected state, and an illegal
write operation is attempted, DATA Polling will not operate.
Write Operation Status Bits
Toggle Bit (I/O6)
The X28C010/X28HT010 provides the user two write
operation status bits. These can be used to optimize a
system write cycle time. The status bits are mapped onto the
I/O bus as shown in Figure 1.
The X28C010/X28HT010 also provides another method for
determining when the internal write cycle is complete. During
the internal programming cycle, I/O6 will toggle from HIGH to
LOW and LOW to HIGH on subsequent attempts to read the
device. When the internal cycle is complete the toggling will
cease and the device will be accessible for additional read or
write operations.
I/O
DP
TB
5
4
3
2
1
0
Reserved
Toggle Bit
DATA Polling
FIGURE 1. STATUS BIT ASSIGNMENT
DATA Polling I/O7
WE
Last
Write
CE
OE
VIH
VOH
HIGH Z
I/O7
VOL
A0-A14
An
An
An
X28C010
Ready
An
An
An
An
FIGURE 2. DATA POLLING BUS SEQUENCE
4
FN8105.1
February 12, 2007
X28C010, X28HT010
DATA Polling can effectively halve the time for writing to the
X28C010/X28HT010. The timing diagram in Figure 2
illustrates the sequence of events on the bus. The software
flow diagram in Figure 3 illustrates one method of
implementing the routine.
Write Data
No
Writes
Complete?
Yes
Save Last Data
and Address
Read Last
Address
IO7
Compare?
No
Yes
X28C010
Ready
FIGURE 3. DATA POLLING SOFTWARE FLOW
The Toggle Bit I/O6
WE
Last
Write
CE
OE
VOH
I/O6
*
HIGH Z
VOL
*
X28C010
Ready
* Beginning and ending state of I/O6 will vary
FIGURE 4. TOGGLE BIT BUS SEQUENCE
5
FN8105.1
February 12, 2007
X28C010, X28HT010
Software Data Protection
The X28C010/X28HT010 offers a software controlled data
protection feature. The X28C010/X28HT010 is shipped from
Intersil with the software data protection NOT ENABLED:
that is the device will be in the standard operating mode. In
this mode data should be protected during power-up/-down
operations through the use of external circuits. The host
would then have open read and write access of the device
once VCC was stable.
Last Write
Load Accum
From Addr N
Compare
Accum with
Addr N
No
Compare
Ok?
The X28C010/X28HT010 can be automatically protected
during power-up and power-down without the need for
external circuits by employing the software data protection
feature. The internal software data protection circuit is
enabled after the first write operation utilizing the software
algorithm. This circuit is nonvolatile and will remain set for
the life of the device unless the reset command is issued.
Once the software protection is enabled, the
X28C010/X28HT010 is also protected from inadvertent and
accidental writes in the powered-up state. That is, the
software algorithm must be issued prior to writing additional
data to the device.
Yes
Ready
FIGURE 5. TOGGLE BIT SOFTWARE FLOW
The Toggle Bit can eliminate the software housekeeping
chore of saving and fetching the last address and data
written to a device in order to implement DATA Polling. This
can be especially helpful in an array comprised of multiple
X28C010/X28HT010 memories that is frequently updated.
Toggle Bit Polling can also provide a method for status
checking in multiprocessor applications. The timing diagram
in Figure 4 illustrates the sequence of events on the bus.
The software flow diagram in Figure 5 illustrates a method
for polling the Toggle Bit.
Software Algorithm
Selecting the software data protection mode requires the
host system to precede data write operations by a series of
three write operations to three specific addresses. Refer to
Figures 6 and 7 for the sequence. The three byte sequence
opens the page write window enabling the host to write from
one to two hundred fifty-six bytes of data. Once the page
load cycle has been completed, the device will automatically
be returned to the data protected state.
Hardware Data Protection
The X28C010/X28HT010 provides three hardware features
that protect nonvolatile data from inadvertent writes.
• Noise Protection—A WE pulse less than 10ns will not
initiate a write cycle.
• Default VCC Sense—All functions are inhibited when VCC
is 3.5V.
• Write inhibit—Holding either OE LOW, WE HIGH, or CE
HIGH will prevent an inadvertent write cycle during powerup and power-down, maintaining data integrity.
6
FN8105.1
February 12, 2007
X28C010, X28HT010
Software Data Protection
VCC
(VCC)
0V
Data
Addr
AA
5555
55
2AAA
A0
5555
Writes
Ok
CE
 tBLC MAX
WE
tWC
Write
Protected
Byte
or
Page
FIGURE 6. TIMING SEQUENCE—BYTE OR PAGE WRITE
Regardless of whether the device has previously been
protected or not, once the software data protection algorithm
is used and data has been written, the X28C010/X28HT010
will automatically disable further writes unless another
command is issued to cancel it. If no further commands are
issued the X28C010/X28HT010 will be write protected
during power-down and after any subsequent power-up. The
state of A15 and A16 while executing the algorithm is don’t
care.
Write Data AA
to Address
5555
Write Data 55
to Address
2AAA
Note: Once initiated, the sequence of write operations
should not be interrupted.
Write Data A0
to Address
5555
Write Data XX
to Any
Address
Optional
Byte/Page
Load Operation
Write Last
Byte
Last Address
After tWC
Re-Enters Data
Protected State
FIGURE 7. WRITE SEQUENCE FOR SOFTWARE DATA
PROTECTION
7
FN8105.1
February 12, 2007
X28C010, X28HT010
Resetting Software Data Protection
VCC
Data
Addr
AA
5555
55
2AAA
80
5555
AA
5555
55
2AAA
20
5555
 tWC
Standard
Operating
Mode
CE
WE
FIGURE 8. RESET SOFTWARE DATA PROTECTION TIMING SEQUENCE
System Considerations
Write Data AA
to Address
5555
Write Data 55
to Address
2AAA
Write Data 80
to Address
5555
Write Data AA
to Address
5555
Write Data 55
to Address
2AAA
Write Data 20
to Address
5555
FIGURE 9. SOFTWARE SEQUENCE TO DEACTIVATE
SOFTWARE DATA PROTECTION
In the event the user wants to deactivate the software data
protection feature for testing or reprogramming in an
EEPROM programmer, the following six step algorithm will
reset the internal protection circuit. After tWC, the
X28C010/X28HT010 will be in standard operating mode.
Because the X28C010/X28HT010 is frequently used in large
memory arrays, it is provided with a two line control
architecture for both read and write operations. Proper
usage can provide the lowest possible power dissipation and
eliminate the possibility of contention where multiple I/O pins
share the same bus.
To gain the most benefit, it is recommended that CE be
decoded from the address bus and be used as the primary
device selection input. Both OE and WE would then be
common among all devices in the array. For a read operation
this assures that all deselected devices are in their standby
mode and that only the selected device(s) is outputting data
on the bus.
Because the X28C010/X28HT010 has two power modes,
standby and active, proper decoupling of the memory array
is of prime concern. Enabling CE will cause transient current
spikes. The magnitude of these spikes is dependent on the
output capacitive loading of the I/Os. Therefore, the larger
the array sharing a common bus, the larger the transient
spikes. The voltage peaks associated with the current
transients can be suppressed by the proper selection and
placement of decoupling capacitors. As a minimum, it is
recommended that a 0.1µF high frequency ceramic
capacitor be used between VCC and VSS at each device.
Depending on the size of the array, the value of the capacitor
may have to be larger.
In addition, it is recommended that a 4.7µF electrolytic bulk
capacitor be placed between VCC and VSS for each eight
devices employed in the array. This bulk capacitor is
employed to overcome the voltage droop caused by the
inductive effects of the PC board traces.
Note: Once initiated, the sequence of write operations
should not be interrupted.
8
FN8105.1
February 12, 2007
X28C010, X28HT010
Active Supply Current vs. Ambient Temperature
18
VCC = 5V
ICC WR (mA)
16
14
12
10
-55
+35
-10
+80
+125
Ambient Temperature (°C)
Standby Supply Current vs. Ambient Temperature
0.3
VCC = 5V
ISB (mA)
0.25
0.2
0.15
0.1
0.05
-55
+35
-10
+80
+125
Ambient Temperature (°C)
ICC (RD) by Temperature Over Frequency
60
5.0 VCC
ICC RD (mA)
50
-55°C
+25°C
40
+125°C
30
20
10
0
3
6
9
12
15
Frequency (MHz)
9
FN8105.1
February 12, 2007
X28C010, X28HT010
Absolute Maximum Ratings
Recommended Operating Conditions
Temperature under bias
X28C010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-10°C to +85°C
X28C010I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
X28C010M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C
X28HT010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +175°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on any pin with respect to VSS . . . . . . . . . . . . . . -1V to +7V
D.C. output current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Lead temperature
(soldering, 10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +300°C
Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C tp +85°C
Military . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +125°C
Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5V ±10%
High Temperature . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +175°C
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of
the device at these or any other conditions (above those indicated in the operational sections of this specification) is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
DC Electrical Specifications
SYMBOL
Over the recommended operating conditions, unless otherwise specified.
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
ICC
VCC Current (Active) (TTL Inputs)
CE = OE = VIL, WE = VIH, All I/O’s = Open,
Address Inputs = 0.4V/2.4V Levels @ f = 5MHz
50
mA
ISB1
VCC Current (Standby) (TTL Inputs)
CE = VIH, OE = VIL, All I/O’s = Open, Other Inputs = VIH
3
mA
ISB2
VCC Current (Standby) (CMOS
Inputs)
CE = VCC - 0.3V, OE = VIL, All I/O’s = Open,
Other Inputs = VCC
500
µA
Input Leakage Current
VIN = VSS to VCC
10
µA
VIN = VSS to VCC (Note 2)
20
µA
ILI
ILO
Output Leakage Current
VOUT = VSS to VCC, CE = VIH
10
µA
VOUT = VSS to VCC, CE = VIH (Note 2)
20
µA
-1
0.8
V
(Note 2)
-1
0.6
V
2
VCC + 1
V
(Note 2)
2.2
VCC + 1
V
IOL = 2.1mA
0.4
V
IOL = 1mA (Note 2)
0.5
V
VlL (Note 1) Input LOW Voltage
VIH (Note 1) Input HIGH Voltage
VOL
VOH
IBB
Output LOW Voltage
Output HIGH Voltage
Back Bias Current
IOH = -400µA
2.4
V
IOH = -400µA
2.6
V
VBB = -3V ±10% (Note 2)
200
µA
NOTE:
1. VIL min. and VIH max. are for reference only and are not tested.
2. X28HT010W
Power-Up Timing
SYMBOL
PARAMETER
MAX
UNIT
tPUR (Note 3)
Power-up to Read operation
100
µs
tPUW (Note 3)
Power-up to Write operation
5
ms
Capacitance
TA = +25°C, f = 1MHz, VCC = 5V
SYMBOL
PARAMETER
TEST CONDITIONS
MAX
UNIT
CI/O (Note 3)
Input/Output capacitance
VI/O = 0V
10
pF
CIN (Note 3)
Input capacitance
VIN = 0V
10
pF
NOTE:
3. This parameter is periodically sampled and not 100% tested.
10
FN8105.1
February 12, 2007
X28C010, X28HT010
Endurance and Data Retention
PARAMETER
MIN
MAX
UNIT
Endurance
10,000
Cycles per byte
Endurance
100,000
Cycles per page
100
Years
Data Retention
Symbol Table
A.C. Conditions of Test
Input pulse levels
0V to 3V
Input rise and fall times
10ns
Input and output timing levels
1.5V
WAVEFORM
Mode Selection
CE
OE
WE
MODE
I/O
POWER
L
L
H
Read
DOUT
Active
L
H
L
Write
DIN
Active
H
X
X
Standby and
Write Inhibit
High Z
Standby
X
L
X
Write Inhibit
—
—
X
X
H
Write Inhibit
—
—
INPUTS
OUTPUTS
Must be
steady
Will be
steady
May change
from LOW
to HIGH
Will change
from LOW
to HIGH
May change
from HIGH
to LOW
Will change
from HIGH
to LOW
Don’t Care:
Changes
Allowed
Changing:
State Not
Known
N/A
Center Line
is High
Impedance
Equivalent A.C. Load Circuit
5V
1.92k
Output
1.37k
100pF
AC Electrical Specifications
Over the recommended operating conditions, unless otherwise specified.
X28C010-12
SYMBOL
PARAMETER
MIN
MAX
X28C010-15
MIN
MAX
X28C010-20,
X28HT010W
MIN
MAX
X28C010-25
MIN
MAX
UNIT
READ CYCLE LIMITS
tRC
Read cycle time
120
150
200
250
ns
tCE
Chip enable access time
120
150
200
250
ns
tAA
Address access time
120
150
200
250
ns
tOE
Output enable access time
50
50
50
50
ns
tLZ (Note 4)
CE LOW to active output
0
0
0
0
ns
tOLZ (Note 4)
OE LOW to active output
0
0
0
0
ns
tHZ (Note 4)
CE HIGH to high Z output
50
50
50
50
ns
tOHZ (Note 4)
OE HIGH to high Z output
50
50
50
50
ns
tOH
Output hold from address change
11
0
0
0
0
ns
FN8105.1
February 12, 2007
X28C010, X28HT010
Read Cycle
tRC
Address
tCE
CE
tOE
OE
VIH
WE
tOLZ
tOHZ
tLZ
Data I/O
HIGH Z
tOH
tHZ
Data Valid
Data Valid
tAA
NOTE:
4. tLZ min.,tHZ, tOLZ min., and tOHZ are periodically sampled and not 100% tested. tHZ max. and tOHZ max. are measured, with CL = 5pF, from the point
when CE or OE return HIGH (whichever occurs first) to the time when the outputs are no longer driven.
Write Cycle Limits
SYMBOL
tWC (Note 5)
PARAMETER
MIN
Write cycle time
MAX
UNIT
10
ms
tAS
Address setup time
0
ns
tAH
Address hold time
50
ns
tCS
Write setup time
0
ns
tCH
Write hold time
0
ns
tCW
CE pulse width
100
ns
tOES
OE HIGH setup time
10
ns
tOEH
OE HIGH hold time
10
ns
tWP
WE pulse width
100
ns
WE HIGH recovery
100
ns
tWPH
tDV
Data valid
tDS
Data setup
50
ns
tDH
Data hold
0
ns
tDW
Delay to next write
10
µs
tBLC
Byte load cycle
0.2
1
12
100
µs
µs
FN8105.1
February 12, 2007
X28C010, X28HT010
WE Controlled Write Cycle
tWC
Address
tAS
tAH
tCS
tCH
CE
OE
tOES
tOEH
tWP
WE
tWPH
tDV
Data In
Data Valid
tDH
tDS
Data Out
HIGH Z
NOTE:
5. tWC is the minimum cycle time to be allowed from the system perspective unless polling techniques are used. It is the maximum time the device
requires to complete internal write operation.
CE Controlled Write Cycle
tWC
Address
tAS
tAH
tCW
CE
tWPH
tOES
OE
tOEH
tCS
tCH
WE
tDV
Data Valid
Data In
tDS
tDH
HIGH Z
Data Out
13
FN8105.1
February 12, 2007
X28C010, X28HT010
Page Write Cycle
OE (Note 5)
CE
tBLC
tWP
WE
tWPH
Address* (Note 7)
Last Byte
I/O
Byte 0
Byte 1
Byte 2
Byte n
Byte n+1
Byte n+2
tWC
*For each successive write within the page write operation, A8-A16 should be the same or
writes to an unknown address could occur.
NOTES:
6. Between successive byte writes within a page write operation, OE can be strobed LOW: e.g. this can be done with CE and WE HIGH to fetch
data from another memory device within the system for the next write; or with WE HIGH and CE LOW effectively performing a polling operation.
7. The timings shown above are unique to page write operations. Individual byte load operations within the page write must conform to either the
CE or WE controlled write cycle timing.
DATA Polling Timing Diagram (Note 8)
Address
An
An
An
CE
WE
tOEH
tOES
OE
tDW
DIN = X
I/O7
DOUT = X
DOUT = X
tWC
14
FN8105.1
February 12, 2007
X28C010, X28HT010
Toggle Bit Timing Diagram
CE
WE
tOES
tOEH
OE
tDW
I/O6
HIGH Z
*
*
tWC
* I/O6 beginning and ending state will vary.
NOTE:
8. Polling operations are by definition read cycles and are therefore subject to read cycle timings.
15
FN8105.1
February 12, 2007
X28C010, X28HT010
Ceramic Dual-In-Line Frit Seal Packages (CERDIP)
F32.6 MIL-STD-1835 GDIP1-T32 (D-16, CONFIGURATION A)
32 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE
LEAD FINISH
c1
-D-
-A-
BASE
METAL
(c)
E
M
-Bbbb S
C A-B S
Q
-C-
SEATING
PLANE
S1
b2
b
ccc M
C A-B S
eA/2
-
0.232
-
5.92
-
0.026
0.36
0.66
2
b1
0.014
0.023
0.36
0.58
3
b2
0.045
0.065
1.14
1.65
-
b3
0.023
0.045
0.58
1.14
4
c
0.008
0.018
0.20
0.46
2
c1
0.008
0.015
0.20
0.38
3
D
-
1.690
-
42.95
5
E
0.500
0.610
15.49
5
c
aaa M C A - B S D S
D S
NOTES
0.014
eA
e
MAX
b

A A
MIN
A
A
L
MILLIMETERS
MAX
M
(b)
D
BASE
PLANE
MIN
b1
SECTION A-A
D S
INCHES
SYMBOL
NOTES:
1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark.
e
12.70
0.100 BSC
2.54 BSC
-
eA
0.600 BSC
15.24 BSC
-
eA/2
0.300 BSC
7.62 BSC
-
L
0.125
0.200
3.18
5.08
-
Q
0.015
0.060
0.38
1.52
6
S1
0.005
-
0.13
-
7
105°
90°
105°
-
2. The maximum limits of lead dimensions b and c or M shall be
measured at the centroid of the finished lead surfaces, when
solder dip or tin plate lead finish is applied.

90°
aaa
-
0.015
-
0.38
-
3. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness.
bbb
-
0.030
-
0.76
-
ccc
-
0.010
-
0.25
-
M
-
0.0015
-
0.038
2, 3
4. Corner leads (1, N, N/2, and N/2+1) may be configured with a
partial lead paddle. For this configuration dimension b3 replaces
dimension b2.
5. This dimension allows for off-center lid, meniscus, and glass
overrun.
N
32
32
8
Rev. 0 8/06
6. Dimension Q shall be measured from the seating plane to the
base plane.
7. Measure dimension S1 at all four corners.
8. N is the maximum number of terminal positions.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
16
FN8105.1
February 12, 2007
X28C010, X28HT010
Packaging Information
32-Lead Ceramic Flat Pack Type F
1.228 (31.19)
1.000 (25.40)
Pin 1 Index
1
0.019 (0.48)
0.015 (0.38)
32
0.050 (1.27) BSC
0.830 (21.08) Max.
0.045 (1.14) Max.
0.005 (0.13) Min.
0.440
0.430 (10.93)
0.007 (0.18)
0.004 (0.10)
0.120 (3.05)
0.090 (2.29)
0.370 (9.40)
0.270 (6.86)
0.347 (8.82)
0.330 (8.38)
0.026 (0.66)
Min.
0.030 (0.76)
Min.
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
17
FN8105.1
February 12, 2007
X28C010, X28HT010
Packaging Information
32-Pad Stretched Ceramic Leadless Chip Carrier Package Type N
0.300 BSC
0.035 x 45° Ref.
Detail A
0.085 ± 0.010
Pin 1
Detail A
0.005/0.015
0.025 ± 0.003
0.006/0.022
0.400 BSC
0.050 ± 0.005
0.050 BSC
0.020 (1.02) x 45° Ref.
Typ. (3) Plcs.
0.450 ± 0.008
0.060/0.120
0.458 Max.
0.700 ± 0.010
0.708 Max.
Pin #1 Index Corner
NOTES:
1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
2. TOLERANCE: ±1% NLT±0.005 (0.127)
18
FN8105.1
February 12, 2007
X28C010, X28HT010
Packaging Information
32-Lead Ceramic Small Outline Gull Wing Package Type R
0.060 Nom.
See Detail “A”
For Lead
Information
0.020 Min.
0.165 Typ.
0.340
±0.007
0.015 R Typ.
0.015 R
Typ.
0.035 Typ.
0.035 Min.
Detail “A”
0.050"
Typical
0.019
0.015
0.830
Max.
0.750
±0.005
0.050
0.050"
Typical
0.560"
Typical
FOOTPRINT
0.030" Typical
32 Places
0.440 Max.
0.560 Nom.
NOTES:
1. ALL DIMENSIONS IN INCHES
2. FORMED LEAD SHALL BE PLANAR WITH RESPECT TO ONE ANOTHER WITHIN 0.004 INCHES
19
FN8105.1
February 12, 2007
X28C010, X28HT010
Packaging Information
36 Lead Ceramic Pin Grid Array Package
Package Code G36.760x760A
15
17
19
21
22
A
13
14
12
11
16
18
20
23
24
25
26
0.008 (0.20)
0.050 (1.27)
A
10
9
27
28
8
7
29
30
6
Typ. 0.180 (.010)
(4.57 ± .25)
4 Corners
5
2
36
34
32
4
3
1
35
33
31
NOTE: Leads 5, 14, 23, & 32
Typ. 0.100 (2.54)
All Leads
Typ. 0.180 (.010)
(4.57 ± .25)
4 Corners
0.120 (3.05)
0.100 (2.54)
0.072 (1.83)
0.062 (1.57)
Pin 1 Index
0.770 (19.56)
0.750 (19.05)
SQ
0.020 (0.51)
0.016 (0.41)
A
A
0.185 (4.70)
0.175 (4.45)
NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS)
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9001 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
20
FN8105.1
February 12, 2007