38267

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
Add packages T and W. Add vendor CAGE 60395 as source of
supply. Increase data retention to 20 years, minimum. Redrawn with
changes.
93-06-29
M. A. Frye
B
Changes in accordance with NOR 5962-R139-94.
94-03-29
M. A. Frye
C
Changes in accordance with NOR 5962-R278-94.
94-09-19
M. A. Frye
D
Changes in accordance with NOR 5962-R163-96.
96-06-27
M. A. Frye
E
Updated boilerplate. Added device types 16-18 and packages M and
N to drawing along with vendor CAGE 0EU86 as supplier. Removed
figures 9, 10 and 11 software data protect algorithms. Removed
vendor 61395 as supplier. - glg
93-03-16
M. A. Frye
F
Corrected dimensions for packages "M" and "N". - glg
95-11-14
M. A. Frye
G
Added device 19, packages 6 and 7, and updated boilerplate. ksr
98-02-20
Raymond Monnin
H
5 year review, updated boilerplate paragraphs. ksr
05-05-18
Raymond Monnin
J
Update drawing to meet current MIL-PRF-38535 requirements. - glg
10-11-05
Charles F. Saffle
K
Update drawing to reflect current MIL-PRF-38535 requirements.
Corrected typos in table I (Write cycle time, Reset protect time, and
Reset high time). - llb
16-01-22
Charles F. Saffle
REV
K
K
K
SHEET
35
36
37
REV
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
SHEET
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
REV STATUS
REV
K
K
K
K
K
K
K
K
K
K
K
K
K
K
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PMIC N/A
PREPARED BY
Kenneth Rice
STANDARD
MICROCIRCUIT
DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
CHECKED BY
Charles Reusing
APPROVED BY
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
Charlie Besore
DRAWING APPROVAL DATE
MICROCIRCUIT, MEMORY, DIGITAL, CMOS
128K x 8 BIT EEPROM, MONOLITHIC SILICON
91-07-12
REVISION LEVEL
K
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
5962-38267
1 OF 37
5962-E079-16
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device class Q and M)
and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or
Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN.
1.2 PIN. The PIN is as shown in the following example:
5962
-
38267
Federal
stock class
designator
\
RHA
designator
(see 1.2.1)
01
M
X
A
Device
type
(see 1.2.2)
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
Lead
finish
(see 1.2.5)
/
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
Generic
number
01,16
02
03,17
04
05,18
06
07,19
08
09
10
11
12
13
14
15
1/
Circuit function
Access time
Write speed
Write mode
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
128K x 8 EEPROM
250 ns
250 ns
200 ns
200 ns
150 ns
150 ns
120 ns
120 ns
90 ns
90 ns
70 ns
70 ns
120 ns
90 ns
70 ns
10 ms
5 ms
10 ms
5 ms
10 ms
5 ms
10 ms
3 ms
10 ms
3 ms
10 ms
3 ms
3 ms
3 ms
3 ms
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Byte/Page
Software
data
protect
Endurance
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
10,000 cycle
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class
M
Q or V
Device requirements documentation
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN
class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Certification and qualification to MIL-PRF-38535
1/ Generic numbers are listed on the Standard Microcircuit Drawing Source Approval Bulletin at the end of this document and
will also be listed in MIL-HDBK-103 and QML-38535.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
2
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
X
Y
Z
U
T
M
N
9
8
Descriptive designator
Terminals
GDIP1-T28 or CDIP2-T28
CQCC1-N32
CDIP3-T28 or GDIP4-T28
CQCC4-N28
GDFP2-F28
CDFP4-F28
See figure 1
See figure 1
See figure 1
Package style
28
32
28
28
28
28
28
36
36
Dual-in-line
Rectangular chip carrier
Dual-in-line
Rectangular chip carrier
Flat pack
Flat pack
Flat pack
Flat pack
Flat pack
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
1.3 Absolute maximum ratings. 2/ 3/
Supply voltage range (VCC) ...........................................................
Operating case temperature range ...............................................
Storage temperature range ...........................................................
Lead temperature (soldering, 10 seconds) ...................................
Thermal resistance, junction-to-case (ϴJC):
Cases X, Y and U .......................................................................
Cases T and W ...........................................................................
Case Z ........................................................................................
Case M .......................................................................................
Case N .......................................................................................
Case 6 ........................................................................................
Case 7 ........................................................................................
Maximum power dissipation (PD) ..................................................
Junction temperature (TJ) .............................................................
Endurance ....................................................................................
Data retention ...............................................................................
-0.5 V dc to +6.0 V dc 4/
-55C to +125C
-65C to +150C
+300C
See MIL-STD-1835
21C/W 5/
18C/W 5/
3C/W 5/
2C/W 5/
1.5C/W 5/
1.5C/W 5/
1.0 watts
+175C 6/
10,000 cycles/byte (minimum)
20 years minimum
1.4 Recommended operating conditions.
Supply voltage range (VCC) ...........................................................
Supply voltage (VSS) .....................................................................
High level input voltage range (VIH) ..............................................
Low level input voltage range (VIL) ...............................................
Case operating temperature range (TC) ........................................
4.5 V dc minimum to 5.5 V dc maximum
0.0 V dc
2.0 V dc to VCC + 1.0 V dc 7/
-0.1 V dc to 0.8 V dc
-55C to +125C
1.5 Digital logic testing for device classes Q and V.
Fault coverage measurement of manufacturing
logic tests (MIL-STD-883, test method 5012) ............................. 100 percent
2/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
3/ All voltages referenced to VSS (VSS = ground), unless otherwise specified.
4/ Negative undershoots to a minimum of -1.0 V are allowed with a maximum of 20 ns pulse width.
5/ When the thermal resistance for this case is specified in MIL-STD-1835, that value shall supersede
the value indicated herein.
6/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screening
conditions in accordance with method 5004 of MIL-STD-883.
7/ For device types 16-19 only, VIH on RES shall be VCC - 0.5 V min. to VCC + 1.0 V max.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
3
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein.
Unless otherwise specified, the issues of the documents are the issues of the documents cited in the solicitation.
ASTM INTERNATIONAL (ASTM)
ASTM Standard F1192
-
Standard Guide for the Measurement of Single Event Phenomena from
Heavy Ion Irradiation of Semiconductor Devices.
(Applications for copies of ASTM publications should be addressed to: ASTM International, PO Box C700, 100 Barr Harbor
Drive, West Conshohocken, PA 19428-2959; http://www.astm.org.)
JEDEC – SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC)
JESD 78
-
IC Latch-Up Test.
(Copies of these documents are available online at http://www.jedec.org or from JEDEC – Solid State Technology
Association, 3103 North 10th Street, Suite 240-S, Arlington, VA 22201-2107.)
(Non-Government standards and other publications are normally available from the organizations that prepare or distribute the
documents. These documents also may be available in or through libraries or other informational services.)
2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 as specified herein, or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
4
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth tables. The truth tables shall be as specified on figure 3.
3.2.3.1 Unprogrammed devices. The truth table for unprogrammed devices for contracts involving no altered item drawing
shall be as specified on figure 3 herein. When required, in screening (see 4.2 herein), or quality conformance inspection groups
A, B, C, or D (see 4.4 herein), the devices shall be programmed by the manufacturer prior to test in a checkerboard or similar
pattern (a minimum of 50 percent of the total number of bits programmed).
3.2.3.2 Programmed devices. The requirements for supplying programmed devices are not part of this document.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103
(see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source
of supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of
MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of
product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing.
3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime’s agent,
and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore
documentation shall be made available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 042 (see MIL-PRF-38535, appendix A).
3.11 Processing of EEPROMs. All testing requirements and quality assurance provisions herein shall be satisfied by the
manufacturer prior to delivery.
3.11.1 Conditions of the supplied devices. Devices will be supplied in an unprogrammed or clear state. No provision will be
made for supplying programmed devices.
3.11.2 Erasure of EEPROMs. When specified, devices shall be erased in accordance with procedures and characteristics
specified in 4.5.1.
3.11.3 Programming of EEPROMs. When specified, devices shall be programmed in accordance with procedures and
characteristics specified in 4.5.2.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
5
3.11.4 Verification of state of EEPROMs. When specified, devices shall be verified as either written to the specified pattern or
cleared. As a minimum, verification shall consist of performing a read of the entire array to verify that all bits are in the proper
state. Any bit that does not verify to be in the proper state shall constitute a device failure and the device shall be removed from
the lot or sample.
3.11.5 Power supply sequence of EEPROMs. In order to reduce the probability of inadvertent writes, the following
power supply sequences shall be observed.
a. For device types 1-19, a logic high state shall be applied to WE and/or CE at the same time or before the
application of VCC. For device types 16-19, an additional precaution is available; a logic low state shall be
applied to RES at the same time or before the application of VCC.
b. For device types 1-19, a logic high state shall be applied to WE and/or CE at the same time or before the
removal of VCC. For device types 16-19, an additional precaution is available; a logic low state shall be applied
to RES at the same time or before the removal of VCC.
3.12 Endurance. A reprogrammability test shall be completed as part of the vendor's reliability monitors. This
reprogrammability test shall be done for initial characterization and after any design or process changes which may affect
the reprogrammability of the device. The methods and procedures may be vendor specific, but shall guarantee the
number of program/erase endurance cycles listed in section 1.3 herein over the full military temperature range. The
vendor's procedure shall be kept under document control and shall be made available upon request of the acquiring or
preparing activity, along with test data.
3.13 Data retention. A data retention stress test shall be completed as part of the vendor's reliability monitors. This
test shall be done for initial characterization and after any design or process change which may affect data retention. The
methods and procedures may be vendor specific, but shall guarantee the number of years listed in section 1.3 herein
over the full military temperature range. The vendor's procedure shall be kept under document control and shall be made
available upon request of the acquiring or preparing activity, along with test data.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
6
TABLE I. Electrical performance characteristics.
Test
High level input
current
Low level input
current
Symbol
Conditions
Group A
subgroups
-55C  TC +125C
VSS = 0 V; 4.5 V  VCC  5.5 V
unless otherwise specified
Device
type
All
-5
5
µA
IIL
VCC = 5.5 V, VIN = 0.1 V
1, 2, 3
All
-5
5
µA
16-19
-100
100
All
-10
10
-10
10
For RES input
IOZL
VIH ≤ OE ≤ VCC
VCC = 5.5 V, VO = 5.5 V
1, 2, 3
Output high voltage
VOH
IOH = -400 µA, VCC = 4.5 V
VIH = 2.0 V, VIL = 0.8 V
1, 2, 3
All
Output low voltage
VOL
IOH = 2.1 µA, VCC = 4.5 V
VIH = 2.0 V, VIL = 0.8 V
1, 2, 3
All
Input high voltage 2/
VIH
VCC = 5.5 V
1, 2, 3
01-15
Input low voltage 2/
VIL
OE high voltage
VH
VCC = 4.5 V
ICC1
2.4
V
V
2.0
6.0
V
16-19
2.2
6.0
1, 2, 3
All
-0.5
0.8
V
1, 2, 3
01-15
12
13
V
16-19
VCC-0.5
VCC+1.0
1, 2, 3
01-06,
08-13,
16, 17
80
07,18,19
100
09-12,
14-15
120
ICC2
VCC = 5.5 V, CE = VIH,
all I/O’s = open,
OE = VIL, f = 0 Hz
1, 2, 3
All
ICC3
VCC = 5.5 V, CE = VCC -0.3 V
Inputs = VIH, I/O’s = open,
OE = VIL, f = 0 Hz
1, 2, 3
01-07
850
08-12
500
13-15,
16-19
350
TTL
CMOS
VCC = 5.5 V, WE = VIH,
CE = OE = VIL
f = 1/tAVAV min
µA
0.4
RES high voltage
Standby supply current
Max
1, 2, 3
1, 2, 3
Standby supply current
Min
VCC = 5.5 V, VIN = 5.5 V
VIH ≤ OE ≤ VCC
VCC = 5.5 V, VO = 5.5 V
Operating supply current
Unit
IIH
IOZH
High impedance output
leakage current 1/
Limits
mA
µA
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
7
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions
-55C  TC +125C
VSS = 0 V; 4.5 V  VCC  5.5 V
unless otherwise specified
Group A
subgroups
Device
type
Limits
Min
Unit
Max
Input capacitance
3/ 4/
CIN
VIN = 0 V, f = 1.0 MHz,
TC = +25C, see 4.4.1c
4
All
10.0
pF
Output capacitance
3/ 4/
COUT
VOUT = 0 V, f = 1.0 MHz
TC = +25C, see 4.4.1c
4
Al
12.0
pF
See 4.4.1d
7, 8A, 8B
All
See figures 4, 5, and 6 as
applicable.
5/
9, 10, 11
01-02,16
250
03-04,17
200
05-06,18
150
07, 08,
13, 19
120
09,10,14
90
11, 12, 15
70
Functional tests
Read cycle time
Address access time
CE access time
OE access time
tAVAV
tAVQV
9, 10, 11
tELQV
9, 10, 11
tOLQV
9, 10, 11
ns
01-02,16
250
03-04,17
200
05-06,18
150
07, 08,
13, 19
120
09,10,14
90
11, 12, 15
70
01-02,16
250
03-04,17
200
05-06,18
150
07, 08,
13, 19
120
09,10,14
90
11, 12, 15
70
01-06
55
07-15
50
16-19
75
CE to output in low Z
4/
tELQX
9, 10, 11
All
Chip disable to output
in high Z
4/
tEHQZ
9, 10, 11
01-06
55
07-19
50
ns
ns
ns
0
ns
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
8
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions
-55C  TC +125C
VSS = 0 V; 4.5 V  VCC  5.5 V
unless otherwise specified
See figures 4, 5, and 6 as
applicable. 5/
Group A
subgroups
Device
type
Limits
Min
Unit
Max
OE to output in low Z
4/
tOLQX
9, 10, 11
All
0
ns
Output disable to output
in high Z
4/
tOHQZ
9, 10, 11
01-06
55
07-19
50
Output hold from address
change
tAXQX
9, 10, 11
All
Write cycle time
tWHWL1
tEHEL1
9, 10, 11
01,03,
05,07,
09,11,
16-19
10
02,04,
06
5
08,10,
12-15
3
ns
0
ns
ns
Address setup time
tAVWL
tAVEL
9, 10, 11
All
0
ns
Address hold time
tWLAX
tELAX
9, 10, 11
16-19
150
ns
01-08,
13
70
09-12,
14, 15
50
Write setup time
tELWL
tWLEL
9, 10, 11
All
0
ns
Write hold time
tWHEH
tEHWH
9, 10, 11
All
0
ns
OE setup time
tOHWL
tOHEL
9, 10, 11
01-15
10
ns
16-19
0
tWHOL
tEHOL
9, 10, 11
01-15
10
16-19
0
Write pulse width (page
or byte write)
tWLWH
tELEH
9, 10, 11
01-15
100
16-19
250
Data setup time
tDVWH
tDVEH
9, 10, 11
16-19
100
01-08,
13
60
09-12,
14, 15
40
OE hold time
ns
ns
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
9
TABLE I. Electrical performance characteristics – Continued.
Test
Data hold time
Symbol
tWHDX
tEHDX
Byte load cycle
tWHWL2
Last byte loaded to
data polling
tWHEL
tEHEL
CE setup time
(chip erase)
tELWL
OE setup time
(chip erase)
Conditions
Group A
subgroups
-55C  TC +125C
VSS = 0 V; 4.5 V  VCC  5.5 V
unless otherwise specified
See figures 4, 5, and 6 as
applicable. 5/
9, 10, 11
9, 10, 11
9, 10, 11
See figures 4, 5, and 6 as
applicable. 5/ 6/
Device
type
Limits
Min
Unit
Max
01-07 1619
10
ns
08-15
0
01-15
.20
149
16-19
.3
30
01-02, 16
250
03-04, 17
200
05-06, 18
150
07, 08,
13, 19
120
09, 10, 14
90
11, 12, 15
70
µs
ns
9, 10, 11
All
5
µs
tWHOH
9, 10, 11
All
5
µs
WE pulse width
(chip clear)
tWLWH2
9, 10, 11
01-07
10
ms
08-15
10
µs
CE hold time
(chip erase)
tWHEH
9, 10, 11
All
5
µs
OE hold time
(chip erase)
tWHOH
9, 10, 11
All
5
µs
High voltage
(chip erase)
VH
9, 10, 11
All
12
Clear recovery
(chip erase)
tOLEL
9, 10, 11
All
Data setup time
(chip erase) 7/
tDHWL
9, 10, 11
All
1
µs
Data hold time during
chip erase cycle 7/
tWHDX
9, 10, 11
All
1
µs
13
V
50
ms
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
10
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
RES low to output float
tDFR
RES to output delay
tRR
Reset protect time
Conditions
-55C  TC +125C
VSS = 0 V; 4.5 V  VCC  5.5 V
unless otherwise specified
See figures 4, 5, and 6 as
applicable. 5/ 8/
Group A
subgroups
Device
type
Limits
Unit
Min
Max
9, 10, 11
16-19
0
350
ns
9, 10, 11
16-19
0
450
ns
tRP
9, 10, 11
16-19
100
µs
Reset high time
tRES
9, 10, 11
16-19
1.0
µs
Time to device busy
tDB
9, 10, 11
16-19
120
ns
1/ Connect all address inputs and OE to VIH and measure IOZL and IOZH with the output under test connected to VOUT.
Terminal connections for the output leakage current test shall be as follows:
a. VIH = 2.0 V for device types 01-15 and 2.2 V for device types 16-19; VIL = 0.8 V.
b. For IOZL: Select an appropriate address to acquire a logic “1” on the designated output. Apply VIH to CE.
Measure the leakage current while applying the specified voltage.
c. For IOZH: Select an appropriate address to acquire a logic “0” on the designated output. Apply VIH to CE.
2/ A functional test shall verify the dc input and output levels and applicable patterns as appropriate, all input and I/O pins shall
be tested. Terminal conditions are as follows:
a. Inputs: H = 2.0 V for device types 01-15 and 2.2 V for device types 16-19; L = 0.8 V. Outputs: H = 2.4 V minimum
and L = 0.4 V maximum.
b. The functional tests shall be performed with VCC = 4.5 V and VCC = 5.5 V.
3/ All pins not being tested are to by open.
4/ Tested initially and after any design or process changes which may affect that parameter, and therefore shall be guaranteed
to the limits specified in table I.
5/ Tested by application of specified timing signals and conditions.
Equivalent ac test conditions:
Output load, see figure 5; input rise and fall times ≤ 10 ns; input pulse levels, 0.4 V and 2.4 V; timing measurement
reference levels, inputs, 1.5 V for device types 1-15 and 1 V and 2 V for device types 16-19; output, 1.5 V for device
types 1-15 and 0.8 V and 2 V for device types 16-19.
6/ Chip erase functions are applicable to device types 01-05 only.
7/ This parameter not applicable for internal timer controlled devices.
8/ RES functions are applicable to device types 16-19 only.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
11
Case T
FIGURE 1. Case outline.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
12
Case W
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
13
Case Z
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
14
Case Z
Variations (all dimensions shown in inches)
Symbol
Min
Max
Notes
A
b
.090
.015
.004
.120
.020
.007
..830
.488
.498
4
c
D
E
E1
E2
E3
.430
.330
.030
e
.050 BSC
H
K
1.228
.015
.008
k1
.025 ref
L
Q
S1
.270
.026
N
Inches
.004
.005
.006
.007
.008
.015
.019
8
2, 5
2, 5
.370
.045
.045
3
32
mm
0.10
0.13
0.15
0.18
0.20
0.38
0.48
Inches
.020
.025
.026
.030
.045
.050
.120
6
mm
0.51
0.64
0.66
0.76
1.14
1.27
3.05
Inches
.270
.350
.370
.472
.488
.498
1.228
mm
6.86
8.89
9.40
11.99
12.40
12.65
31.19
NOTES:
1.
All dimensions and tolerances conform to ANSI Y14.5M-1982.
2.
Index area: An identification mark shall be located adjacent to pin 1 within the shaded area shown. Alternatively,
a tab (dim k) may be used as shown.
3.
Dimension Q shall be measured from the point on the lead located opposite the braze pad.
4.
This dimension includes lid thickness.
5.
Optional, see note 2. If pin 1 identification is used instead of this tab, the minimum dimension does not apply.
6.
(N) indicates number of leads.
7.
Uses a metal lid.
8.
Includes braze fillet.
9.
Metric equivalents are given for general information only.
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
15
Case M
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
16
Case M
Variations
Millimeters
Symbol
Inches
Min
Max
Min
Max
A
A1
b
c
D
D2
E
E1
2.46
2.29
.038
0.08
20.57
18.92
10.80
8.38
3.12
2.79
.048
0.18
21.08
19.18
11.30
9.04
.097
.090
.015
.003
.810
.745
.425
.330
.123
.110
.019
.007
.830
.755
.445
.356
e
1.14
1.40
.045
.055
H
25.40
27.94
1.00
1.10
L
Q
7.37
0.66
7.87
0.94
.290
.026
.310
.037
N
32
NOTE: Although dimensions are in inches, the US government preferred system of measurement is the metric SI system.
However, since this item was originally designed using inch-pound units of measurement, in the event of conflict
between the two, the inch-pound units shall take precedence. Metric equivalents are for general information only.
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
17
Case N
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
18
Case N
Variations
Millimeters
Symbol
Inches
Min
Max
Min
Max
A
A1
b
c
D
D1
D2
E
E1
3.18
2.29
0.38
0.08
20.57
19.69
18.92
10.80
7.37
3.81
2.79
0.48
0.18
21.08
19.94
19.18
11.30
7.87
.125
.090
.015
.003
.810
.775
.745
.425
.290
.150
.110
.019
.007
.830
.785
.755
.445
.310
e
1.14
1.40
.045
.055
H
25.40
27.94
1.00
1.10
L
Q
7.37
0.66
7.87
0.94
.290
.026
.310
.037
N
32
NOTE: Although dimensions are in inches, the US government preferred system of measurement is the metric SI system.
However, since this item was originally designed using inch-pound units of measurement, in the event of conflict
between the two, the inch-pound units shall take precedence. Metric equivalents are for general information only.
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
19
Case 6
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
20
Case 6
Variations
Millimeters
Symbol
A
b
c
D
E
E1
E2
E3
Min
Max
Min
Max
3.07
0.38
0.10
3.81
0.56
0.18
21.08
12.40
7.87
.121
.015
.004
.150
.022
.009
.830
.488
.498
11.99
.472
7.72
0.76
e
.304
.030
1.27
S1
0.13
L
Q
9.02
0.51
N
NOTE:
Inches
.050 BSC
.005
9.53
1.14
.355
.020
.375
.045
32
Although dimensions are in inches, the US government preferred system of measurement is the metric SI system.
However, since this item was originally designed using inch-pound units of measurement, in the event of conflict
between the two, the inch-pound units shall take precedence. Metric equivalents are for general information only.
This package is manufactured for additional Rad tolerant capabilities; contact the vendor for specific information.
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
21
Case 7
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
22
Case 7
Variations
Millimeters
Symbol
A
b
c
D
E
E1
E2
E3
Inches
Min
Max
Min
Max
2.97
.38
0.08
3.63
0.56
0.23
21.08
10.57
11.18
.117
.015
.003
.143
.022
.009
.830
.416
.440
10.26
.404
5.94
0.76
e
.234
.030
1.27
S1
0.13
L
Q
8.89
0.53
N
.050 BSC
.005
10.41
0.91
.350
.021
.410
.036
32
NOTE: Although dimensions are in inches, the US government preferred system of measurement is the metric SI system.
However, since this item was originally designed using inch-pound units of measurement, in the event of conflict
between the two, the inch-pound units shall take precedence. Metric equivalents are for general information only.
This package is manufactured for additional Rad tolerant capabilities; contact the vendor for specific information.
FIGURE 1. Case outline – Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
23
Device types
Case outlines
01 – 15
X, Z, U
Y
W
Terminal
number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
16 – 19
T
U
M, N,6,7
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
I/O3
I/O4
I/O5
I/O6
I/O7
CE
A10
OE
A11
A9
A8
A13
WE
VCC
A15
A16
-----------------------------
RDY/ BUSY
A16
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
I/O3
I/O4
I/O5
I/O6
I/O7
CE
A10
OE
A11
A9
A8
A13
WE
RES
A15
VCC
-------------------------
RDY/ BUSY
A16
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
I/O3
I/O4
I/O5
I/O6
I/O7
CE
A10
OE
A11
A9
A8
A13
WE
RES
A15
VCC
-------------------------
Terminal symbol
NC
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
I/O3
I/O4
I/O5
I/O6
I/O7
CE
A10
OE
A11
A9
A8
A13
A14
NC
WE
VCC
-------------------------
NC
NC
NC
NC
A16
A15
A12
A7
A6
A5
NC
NC
NC
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
NC
I/O3
I/O4
I/O5
I/O6
I/O7
CE
A10
OE
NC
NC
NC
NC
A11
A9
A8
A13
A14
NC
NC
WE
VCC
NC
NC
NC
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
I/O0
I/O1
I/O2
VSS
I/O3
I/O4
I/O5
I/O6
I/O7
CE
A10
OE
A11
A9
A8
A13
A14
NC
NC
NC
WE
VCC
-----------------
NC = no connection
FIGURE 2. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
24
Device types 01-15
Mode
CE
OE
WE
I/O
Read
VIL
VIL
VIH
DOUT
Write
VIL
VIH
VIL
DIN
Standby
VIH
X
X
High Z
Write inhibit
X
X
VIH
DOUT or High Z
Write inhibit
VIH
X
X
High Z
Write inhibit
X
VIL
X
DOUT or High Z
Write inhibit
VIL
VIL
VIL
No operation
Software chip clear
VIL
VIH
VIL
DIN
Software write protect
VIL
VIH
VIL
DIN
High voltage chip clear
VIL
VH
VIL
VIH
VIH = High logic, "1" state, VIL = Low logic, "0" state.
X = logic "don't care" state, High Z = high impedance state.
VH = Chip clear voltage, DOUT = Data out, and
DIN = Data in.
Device types 16-19
Mode
CE
OE
WE
RES
RDY/ BUSY
I/O
Read
VIL
VIL
VIH
VH
High Z
DOUT
Standby
VIH
X
X
X
High Z
High Z
Write
VIL
VIH
VIL
VH
High Z to VOL
DIN
Deselect
VIL
VIH
VIH
VH
High Z
High Z
Write inhibit
X
X
VIH
X
---
---
Write inhibit
X
VIL
X
X
---
---
DATA polling
VIL
VIL
VIH
VH
VOL
DOUT (I/O7)
Program reset
X
X
X
VIL
High Z
High Z
VIH = High logic, "1" state, VIL = Low logic, "0" state.
X = logic "don't care" state, High Z = high impedance state.
DIN = Data in, DOUT = Data out, and VH = VCC-0.5 V to VCC+1.0 V.
FIGURE 3. Truth table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
25
READ MODE WAVEFORM
NOTE: RES waveform is applicable to device types 16-19 only.
FIGURE 4. Waveforms.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
26
WE CONTROLLED BYTE WRITE WAVEFORMS
NOTE: RDY/ BUSY, RES, and VCC waveforms are applicable to device types 16-19 only.
FIGURE 4. Waveforms - continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
27
CE CONTROLLED BYTE WRITE WAVEFORMS
NOTE: RDY/ BUSY, RES, and VCC waveforms are applicable to device types 16-19 only.
FIGURE 4. Waveforms - continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
28
PAGE WRITE MODE CYCLE WAVEFORMS
NOTE: RDY/ BUSY, RES, and VCC waveforms are applicable to device types 16-19 only.
FIGURE 4. Waveforms - continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
29
CHIP ERASE WAVEFORMS (device types 01 – 15 only)
FIGURE 4. Waveforms - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
30
O
NOTES:
1. VOH and VOL will be adjusted to meet load conditions of table I.
2. Use this circuit or equivalent circuit.
FIGURE 5. Switching load circuit.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
31
4. VERIFICATION
4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with
MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan
shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in
accordance with MIL-PRF-38535, appendix A.
4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted
on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in
accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection.
4.2.1 Additional criteria for device class M.
a.
Delete the sequence specified as initial (preburn-in) electrical parameters through interim (postburn-in) electrical
parameters of method 5004 and substitute lines 1 through 6 of table IIA herein.
b.
Prior to burn-in, the devices shall be programmed (see 4.5.2 herein) with a checkerboard pattern or equivalent
(manufacturers at their option may employ an equivalent pattern provided it is a topologically true alternating bit
pattern). The pattern shall be read before and after burn-in. Devices having bits not in the proper state after burn-in
shall constitute a device failure and shall be included in the PDA calculation and shall be removed from the lot.
c.
Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control
and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125C, minimum.
d.
Interim and final electrical test parameters shall be as specified in table IIA herein.
e.
After the completion of all screening, the device shall be erased and verified prior to delivery.
4.2.2 Additional criteria for device classes Q and V.
a.
The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the
device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under
document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1015 of MIL-STD-883.
b.
Interim and final electrical test parameters shall be as specified in table IIA herein.
c.
Additional screening for device class V beyond the requirements of device class Q shall be as specified in
MIL-PRF-38535, appendix B.
4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in
accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups
A, B, C, D, and E inspections (see 4.4.1 through 4.4.4).
4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with
MIL-PRF-38535 including groups A, B, C, D, and E inspections, and as specified herein. Quality conformance inspection for
device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed
for device class M shall be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections
(see 4.4.1 through 4.4.4).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
32
4.4.1 Group A inspection.
a.
Tests shall be as specified in table IIA herein.
b.
Subgroups 5 and 6 of table I of method 5005 of MIL-STD-883 shall be omitted.
c.
Subgroup 4 (CIN and COUT measurements) shall be measured only for initial qualification and after any process or
design changes which may affect input or output capacitance. Capacitance shall be measured between the
designated terminal and GND at a frequency of 1 MHz. Sample size is 15 devices with no failures, and all input and
output terminals tested.
d.
For device class M, subgroups 7 and 8 tests shall be sufficient to verify the truth table. For device classes Q and V,
subgroups 7 and 8 shall include verifying the functionality of the device, these tests shall have been fault graded in
accordance with MIL-STD-883, test method 5012 (see 1.5 herein).
e.
O/V (latch-up) tests shall be measured only for initial qualification and after any design or process changes which may
affect the performance of the device. For device class M, procedures and circuits shall be maintained under document
revision level control by the manufacturer and shall be made available to the preparing activity or acquiring activity upon
request. For device classes Q and V, the procedures and circuits shall be under the control of the device
manufacturer's TRB in accordance with MIL-PRF-38535 and shall be made available to the preparing activity or
acquiring activity upon request. Testing shall be on all pins, on five devices with zero failures. Latch-up test shall be
considered destructive. Information contained in JESD78 may be used for reference.
f.
All devices selected for testing shall be programmed with a checkerboard pattern or equivalent. After completion of all
testing, the devices shall be erased and verified, (except devices submitted for groups C and D testing).
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein.
4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:
a.
Test condition D or E. The test circuit shall be maintained by the manufacturer under document revision level control
and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs,
outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of
MIL-STD-883.
b.
TA = +125C, minimum.
c.
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
d.
All devices requiring end-point electrical testing shall be programmed with a checkerboard or equivalent alternating bit
pattern.
e.
After the completion of all testing, the devices shall be cleared and verified prior to delivery.
4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature,
or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The
test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of
MIL-STD-883.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
33
TABLE IIA. Electrical test requirements. 1/ 2/ 3/ 4/ 5/ 6/ 7/
Line
no.
Test requirements
Subgroups
(in accordance with
MIL-STD-883,
TM 5005, table I)
Subgroups
(in accordance with
MIL-PRF-38535, table III)
Device
class M
1
Interim electrical
parameters (see 4.2)
2
Static burn-in
(method 1015)
3
Same as line 1
4
Dynamic burn-in
(method 1015)
5
Same as line 1
6
Final electrical
parameters (see 4.2)
7
Group A test requirements
(see 4.4)
8
Not
required
Device
class Q
Device
class V
1, 7, 9
or
2, 8A, 10
1, 7, 9
or
1, 2, 8A, 10
Not
required
Required
1*, 7* 
Required
Required
Required
1*, 7* 
1*, 2, 3, 7*, 8A,
8B, 9, 10, 11
1*, 2, 3, 7*, 8A,
8B, 9, 10, 11
1*, 2, 3, 7*, 8A,
8B, 9, 10, 11
1, 2, 3, 4**, 7,
8A, 8B, 9, 10, 11
1, 2, 3, 4**, 7,
8A, 8B, 9, 10, 11
1, 2, 3, 4**, 7,
8A, 8B, 9, 10, 11
Group C end-point electrical
parameters (see 4.4)
2, 3, 7, 8A, 8B
1*, 2, 3, 7, 8A,
8B, 9, 10, 11 
1, 2, 3, 7, 8A,
8B, 9, 10, 11 
9
Group D end-point electrical
parameters (see 4.4)
2, 3, 7, 8A,
8B
2, 3, 7, 8A,
8B
2, 3, 7, 8A,
8B
10
Group E end-point electrical
parameters (see 4.4)
1, 7, 9
1, 7, 9
1, 7, 9
1/
2/
3/
4/
5/
6/
Blank spaces indicate tests are not applicable.
Any or all subgroups may be combined when using high-speed testers.
Subgroups 7 and 8 functional tests shall verify the truth table.
* indicates PDA applies to subgroup 1 and 7.
** see 4.4.1c.
 indicates delta limit (see table IIB) shall be required where specified, and the delta values shall be computed
with reference to the previous interim electrical parameters (see line 1).
7/ See 4.4.1e.
TABLE IIB. Delta limits at +25C.
Test 1/
All device types
ICC3 standby
± 10% of specified value in table I
IIH, IIL
± 10% of specified value in table I
IOHZ, IOLZ
± 10% of specified value in table I
1/ The above parameter shall be recorded before and after the required
burn-in and life tests to determine the delta .
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
34
4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein.
The devices selected for testing shall be programmed with a checkerboard pattern. After completion of all testing, the devices
shall be erased and verified.
4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured
(see 3.5 herein).
a.
End-point electrical parameters shall be as specified in table IIA herein.
b.
For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as
specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to
radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All device
classes must meet the postirradiation end-point electrical parameter limits as defined in table I at TA = +25C 5C,
after exposure, to the subgroups specified in table IIA herein.
4.5 Methods of inspection. Methods of inspection shall be as specified in the appropriate figures and tables herein.
4.5.1 Erasing procedures. The erasing procedures shall be as specified by the device manufacturer and shall be available
upon request.
4.5.2 Programming procedure. The programming procedures shall be as specified by the device manufacturer and shall be
made available upon request.
4.5.3 Software data protect procedures. The software data protect procedures shall be as specified by the device
manufacturer and shall be made available upon request.
4.6 Delta measurements for device class V. Delta measurements, as specified in table IIA, shall be made and recorded
before and after the required burn-in screens and steady-state life tests to determine delta compliance. The electrical
parameters to be measured, with associated delta limits are listed in table IIB. The device manufacturer may, at his option,
either perform delta measurements or within 24 hours after burn-in perform final electrical parameter tests, subgroups 1, 7, 9.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes
Q and V or MIL-PRF-38535, appendix A for device class M.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor
prepared specification or drawing.
6.1.2 Substitutability. Device class Q devices will replace device class M devices.
6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.3 Record of users. Military and industrial users should inform DLA Land and Maritime when a system application requires
configuration control and which SMD's are applicable to that system. DLA Land and Maritime will maintain a record of users and
this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic
devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108.
6.4 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-0540.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
35
6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in
MIL-PRF-38535 and MIL-HDBK-1331, and as follows:
CIN, COUT ................
GND .......................
ICC ..........................
IIL ............................
IIH ...........................
TC ...........................
TA ...........................
VCC .........................
VH...........................
O/V.........................
Input and bidirectional output, terminal-to-GND capacitance.
Ground zero voltage potential.
Supply current.
Input current low.
Input current high.
Case temperature.
Ambient temperature.
Positive supply voltage.
Output enable and Write enable voltage during chip erase.
Latchup over-voltage.
6.5.1 Timing limits. The table of timing values shows either a minimum or a maximum limit for each parameter. Input
requirements are specified from the external system point of view. Thus, address setup time is shown as a minimum since the
system must supply at least that much time (even though most devices do not require it). On the other hand, responses from
the memory are specified from the device point of view. Thus, the access time is shown as a maximum since the device never
provides data later than that time.
6.5.2 Timing parameter abbreviations. All timing abbreviations use lower case characters with upper case subscripts. The
initial character is always "t" and is followed by four descriptors. These characters specify two signal points arranged in a "fromto" sequence that define a timing interval. The two descriptors for each signal specify the signal name and the signal transition.
Thus the format is:
t
Signal name from which interval is defined
Transition direction for first signal
X



X





X







Signal name to which interval is defined
Transition direction for second signal
a. Signal definitions:
A = Address
D = Data in
Q = Data out
W = Write enable
E = Chip enable
G = Output enable
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
b.
X









Transition definitions:
H = Transition to high
L = Transition to low
V = Transition to valid
X = Transition to invalid or don't care
Z = Transition to off (high impedance)
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
36
6.5.3 Waveforms.
Waveform
symbol
Input
Output
MUST BE VALID
WILL BE VALID
CHANGE FROM
H TO L
WILL CHANGE FROM
H TO L
CHANGE FROM
L TO H
WILL CHANGE FROM
L TO H
DON'T CARE
ANY CHANGE
PERMITTED
CHANGING
STATE UNKNOWN
HIGH
IMPEDANCE
6.6 Sources of supply.
6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in
MIL-HDBK-103 and QML-38535. The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein)
to DLA Land and Maritime-VA and have agreed to this drawing.
6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103.
The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been
submitted to and accepted by DLA Land and Maritime-VA.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-38267
A
REVISION LEVEL
K
SHEET
37
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 16-01-22
Approved sources of supply for SMD 5962-38267 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information
bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-3826701MTA
0HSW3
AT28C010-25UM/883
5962-3826701MUA
0HSW3
AT28C010-25EM/883
5962-3826701MWC
3/
3/
5962-3826701MXA
0HSW3
57300
3/
3/
AT28C010-25DM/883
AS28C010CW-25
X28C010DMB-25
CM28C010-250
5962-3826701MYA
0HSW3
57300
3/
AT28C010-25LM/883
AS28C010CW-25
LM28C010-250
5962-3826701MZA
57300
0HSW3
3/
3/
AS28C010F-25
AT28C010-25FM/883
X28C010FMB-25
FM28C010-250
5962-3826701MZC
3/
28C010-25
5962-3826702MWA
3/
TM28C010H-250
5962-3826702MXA
3/
CM28C010H-250
5962-3826702MYA
3/
LM28C010H-250
5962-3826702MZA
3/
FM28C010H-250
5962-3826703MTA
0HSW3
AT28C010-20UM/883
5962-3826703MUA
0HSW3
AT28C010-20EM/883
5962-3826703MWC
3/
3/
5962-3826703MXA
0HSW3
3/
3/
57300
AT28C010-20DM/883
X28C010DMB-20
CM28C010-200
AS28C010CW-20
5962-3826703MYA
0HSW3
3/
AT28C010-20LM/883
LM28C010-200
5962-3826703MZA
57300
0HSW3
3/
3/
AS28C010F-20
AT28C010-20FM/883
X28C010FMB-20
FM28C010-200
5962-3826703MZC
3/
28C010-20
5962-3826704MXA
3/
CM28C010H-200
5962-3826704MYA
3/
LM28C010H-200
5962-3826704MZA
3/
FM28C010H-200
X28C010KMB-25
TM28C010-250
X28C010KMB-20
TM28C010-200
See footnotes at end of table.
1 of 4
STANDARD MICROCIRCUIT DRAWING BULLETIN – Continued.
DATE: 16-01-22
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-3826704MWA
3/
5962-3826705MTA
0HSW3
AT28C010-15UM/883
5962-3826705MUA
0HSW3
AT28C010-15EM/883
5962-3826705MWC
3/
3/
5962-3826705MXA
3/
57300
3/
3/
AT28C010-15DM/883
AS28C010CW-15
X28C010DMB-15
CM28C010-150
5962-3826705MYA
0HSW3
3/
AT28C010-15LM/883
LM28C010-150
5962-3826705MZA
57300
0HSW3
3/
3/
AS28C010F-15
AT28C010-15FM/883
X28C010FMB-15
FM28C010-150
5962-3826705MZC
3/
28C010F-15
5962-3826706MXA
3/
CM28C010H-150
5962-3826706MYA
3/
LM28C010H-150
5962-3826706MZA
3/
FM28C010H-150
5962-3826706MWA
3/
TM28C010H-150
5962-3826707MTA
0HSW3
AT28C010-12UM/883
5962-3826707MUA
0HSW3
AT28C010-12EM/883
5962-3826707MWC
3/
3/
5962-3826707MXA
0HSW3
57300
3/
3/
AT28C010-12DM/883
AS28C010CW-12
X28C010DMB-12
CM28C010-120
5962-3826707MYA
0HSW3
3/
AT28C010-12LM/883
LM28C010-120
5962-3826707MZA
0HSW3
3/
3/
57300
AT28C010-12FM/883
X28C010FMB-12
FM28C010-120
AS28C010F-12
5962-3826707MZC
3/
5962-3826716Q6C
68911
28C010TRPFB-25
5962-3826716Q7C
68911
28C011TRPFB-25
5962-3826716QMA
57300
AS58C1001F-25/883C
5962-3826716QMC
68911
28C010TFB-25
5962-3826716QNA
57300
AS58C1001SF-25/883C
5962-3826716QUA
57300
AS58C1001ECA-25/883C
5962-3826716V6C
68911
28C010TRPFS-25
See footnotes at end of table.
2 of 4
TM28C010H-200
X28C010KMB-15
TM28C010-150
X28C010KMB-12
TM28C010-120
28C010F-12
STANDARD MICROCIRCUIT DRAWING BULLETIN – Continued.
DATE: 16-01-22
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-3826716V7C
68911
28C011TRPFS-25
5962-3826716VMC
68911
28C010TFS-25
5962-3826717Q6C
68911
28C010TRPFB-20
5962-3826717Q7C
68911
28C011TRPFB-20
5962-3826717QMA
57300
AS58C1001F-20/883C
5962-3826717QMC
68911
28C010TFB-20
5962-3826717QNA
57300
AS58C1001SF-20/883C
5962-3826717QUA
57300
AS58C1001ECA-20/883C
5962-3826717V6C
68911
28C010TRPFS-20
5962-3826717V7C
68911
28C011TRPFS-20
5962-3826717VMC
68911
28C010TFS-20
5962-3826718Q6C
68911
28C010TRPFB-15
5962-3826718Q7C
68911
28C011TRPFB-15
5962-3826718QMA
57300
AS58C1001F-15/883C
5962-3826718QMC
68911
28C010TFB-15
5962-3826718QNA
57300
AS58C1001SF-15/883C
5962-3826718QUA
57300
AS58C1001ECA-15/883C
5962-3826718V6C
68911
28C010TRPFS-15
5962-3826718V7C
68911
28C011TRPFS-15
5962-3826718VMC
68911
28C010TFS-15
5962-3826719Q6C
68911
28C010TRPFB-12
5962-3826719Q7C
68911
28C011TRPFB-12
5962-3826719QMC
68911
28C010TFBS-12
5962-3826719V6C
68911
28C010TRPFS-12
5962-3826719V7C
68911
28C011TRPFS-12
5962-3826719VMC
68911
28C010TFS-12
1/ The lead finish shown for each PIN representing a hermetic package
is the most readily available from the manufacturer listed for that
part. If the desired lead finish is not listed contact the vendor to
determine its availability.
2/ Caution. Do not use this number for item acquisition. Items
acquired to this number may not satisfy the performance
requirements of this drawing.
3 of 4
STANDARD MICROCIRCUIT DRAWING BULLETIN – Continued.
DATE: 16-01-22
Vendor CAGE
number
Vendor name
and address
0HSW3
Atmel Corp.
1150 East Cheyenne Mountain Blvd.
Colorado Springs, CO 80906
57300
Micross Components
7725 N. Orange Blossom Trail
Orlando, FL 32810-2696
68911
Maxwell Technologies Electronics
Components Group, Inc.
9244 Balboa Ave.
San Diego, CA 92123
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the information
bulletin.
4 of 4