PANASONIC ENW89811J4CF

P

Cut the Cable
TM
Bluetooth-Module PAN1321
OUTLINES - ENW89811J4CF
(Module with shielding)
M
ODULES
Panasonic
Electronic Devices Europe GmbH
IRELESS
W
Now you can integrate Bluetooth very easy in your final
product, with the PAN1321-SPP as a full Bluetooth system
solution.
In comparison to our pin compatible HCI solution (PAN1310),
there is no longer a powerful host needed.
The PAN1321 is manufactured in a 15,6 x 8,7 x 2.8 mm³ SMD
LGA package with shielded case and will be qualified to the
Bluetooth 2.0 standard.
Due to a very low price PAN1321 is well suited for units
produced in all quantities, with the simple AT command set
you are able to integrate PAN1321 into your application.
This module follows the national and international
regulations, e.g. EMC, Safety, EN300328, FCC.
FEATURES
General
- Supported Profiles: RFCOMM, SPP device A and B
- Complete Bluetooth 2.0 + EDR solution
- Ultra low power design
- Temperature from -40°C to +70°C, optional +85°C (Industrial Range)
- No external components needed
- Integrates ARM7TDMI, RAM and patchable 256k EEPROM
(for device configuration data and application)
- On-module voltage regulator. External supply 2.7-3.6V
- Reference clock included
- Low power clock from internal oscillator or external low power clock
Interfaces
- 3.25 MBaud UART
- General purpose I/Os with interrupt and wake-up capabilities
- JTAG for boundary scan and debug
Bluetooth
- Scatternet with one slave role while still being visible
- Power control and RSSI
- Sniff mode, Adaptive Frequency Hopping and Quality of Service
ORDERING CODE
- PAN1321 with SPP and max. +70°C
- PAN1321 with SPP and max. +85°C
ENW89811J4CF
(on request for higher demand)
Design and Specifications are subject to change without notice. Ask the factory for technical specifications before purchase and/or use. If there is any doubt
regarding the safety of this product, kindly inform us immediately for technical consultation.
PAN1321 Rev. B1
www.pedeu.panasonic.de
[email protected]
Hardware Status:
Pre Production
P
CONTACT
Hy-Line Communication GmbH
Inselkammerstr. 10
82008 Unterhaching/Munich, Germany
Tel. +49 (0)89-614503-236
Fax +49 (0)89-6140960
E-Mail: [email protected]
HTTP: www.hy-line.de/communication
APPLICATIONS
All Wireless Applications
- Printer Adapters and Scanners
- Printers
- Access Points
- Wireless Sensors
-
Cable Replacement
Personal Digital Assistants (PDAs)
PC Motherboards & - Peripherals
Industrial Applications
BLOCK DIAGRAM
TECHNICAL CHARACTERISTICS
Parameter
-3
Receiver Sensitivity (BER=10 )
Output Power
Value
Condition / Note
-86 dBm typ.
ideal wanted signal
+3 dBm typ.
@ 50 Ohm antenna pin
Power Supply
2,7 - 3,6 V
Single operation voltage
Ultra Low Power Mode
80µA
T = 25°C
ACL (Transmit 3-DH1)
40mA
Enhanced Data Rate, 531.2 kb/s (1)
ACL (Receive 3-DH1)
37mA
Enhanced Data Rate, 531.2 kb/s (1)
Operating Temperature Range
-40°C to +70°C
optional +85°C
(1) Figure indicates maximum possible data rate with this packet type.
Total throughput depends on application and interface setting.
www.pedeu.panasonic.de
[email protected]
Hardware Status:
Pre Production