TPSMA6.8 thru TPSMA43A www.vishay.com Vishay General Semiconductor Surface Mount PAR® Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions FEATURES • Junction passivation optimized design passivated anisotropic rectifier technology • TJ = 185 °C capability suitable for high reliability and automotive requirement • Available in uni-directional polarity only • 400 W peak pulse power capability with a 10/1000 μs waveform, repetitive rate (duty cycle): 0.01 % DO-214AC (SMA) • Excellent clamping capability • Very fast response time • Low incremental surge resistance • Meets MSL level 1, per J-STD-020, LF maximum peak of 260 °C PRIMARY CHARACTERISTICS VWM 5.5 V to 36.8 V VBR 6.8 V to 43 V PPPM 400 W PD 1.0 W IFSM 40 A TJ max. 185 °C Polarity Uni-directional Package DO-214AC (SMA) • AEC-Q101 qualified • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA Case: DO-214AC (SMA) Molding compound meets UL 94 V-0 flammability rating Base P/NHE3_X - RoHS-compliant and AEC-Q101 qualified (“_X” denotes revision code e.g. A, B, .....) TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive and telecommunication. Terminals: Matte tin plated leads, solderable J-STD-002 and JESD 22-B102 HE3 suffix meets JESD 201 class 2 whisker test per Polarity: Color band denotes cathode end MAXIMUM RATINGS (TA = 25 °C unless otherwise noted) PARAMETER SYMBOL Peak power dissipation with a 10/1000 μs waveform (1)(2) VALUE UNIT (fig. 3) PPPM 400 W Peak power pulse current with a 10/1000 μs waveform (1) (fig. 1) IPPM See next table A PD 1.0 W IFSM 40 A Power dissipation at TA = 25 °C (4) Peak forward surge current 8.3 ms single half sine-wave (3) Maximum instantaneous forward voltage at 25 A (3) Operating junction and storage temperature range VF 3.5 V TJ, TSTG - 65 to + 185 °C Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 °C per fig. 2 A (2) Mounted on PCB with 0.2" x 0.2" (5.0 mm x 5.0 mm) copper pads attached to each terminal (3) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minutes maximum (4) Mounted on minimum recommended pad layout Revision: 25-Apr-14 Document Number: 88405 1 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TPSMA6.8 thru TPSMA43A www.vishay.com Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted) DEVICE TYPE DEVICE MARKING CODE BREAKDOWN VOLTAGE VBR (1) AT IT (V) MIN. MAX. TJ = 150 °C STAND- MAXIMUM MAXIMUM TEST OFF REVERSE REVERSE CURRENT VOLTAGE LEAKAGE LEAKAGE AT IT VWM AT VWM VWM (mA) (V) IR (μA) ID (μA) MAXIMUM PEAK MAXIMUM PULSE CLAMPING SURGE VOLTAGE CURRENT AT IPPM IPPM (2) VC (V) (A) TPSMA6.8 ADP 6.12 7.48 10 5.50 300 1000 37.0 TPSMA6.8A AEP 6.45 7.14 10 5.80 300 1000 38.1 10.8 10.5 TPSMA7.5 AFP 6.75 8.25 10 6.05 150 500 34.2 11.7 TPSMA7.5A AGP 7.13 7.88 10 6.40 150 500 35.4 11.3 TPSMA8.2 AHP 7.38 9.02 10 6.63 50 200 32.0 12.5 TPSMA8.2A AKP 7.79 8.61 10 7.02 50 200 33.1 12.1 TPSMA9.1 ALP 8.19 10.00 1.0 7.37 10 50 29.0 13.8 TPSMA9.1A AMP 8.65 9.55 1.0 7.78 10 50 29.9 13.0 TPSMA10 ANP 9.00 11.00 1.0 8.10 5.0 20 26.7 15.0 TPSMA10A APP 9.50 10.50 1.0 8.65 5.0 20 27.6 14.5 TPSMA11 AQP 9.90 12.10 1.0 8.92 1.0 5.0 24.7 16.2 TPSMA11A ARP 10.50 11.60 1.0 9.40 1.0 5.0 25.6 15.6 TPSMA12 ASP 10.80 13.20 1.0 9.72 1.0 5.0 23.1 17.3 TPSMA12A ATP 11.40 12.60 1.0 10.20 1.0 5.0 24.0 16.7 TPSMA13 AUP 11.70 14.30 1.0 10.50 1.0 5.0 21.1 19.0 TPSMA13A AVP 12.40 13.70 1.0 11.10 1.0 5.0 22.0 18.2 TPSMA15 AWP 13.50 16.30 1.0 12.10 1.0 5.0 18.2 22.0 TPSMA15A AXP 14.30 15.80 1.0 12.80 1.0 5.0 18.9 21.2 TPSMA16 AYP 14.40 17.60 1.0 12.90 1.0 5.0 17.0 23.5 TPSMA16A AZP 15.20 16.80 1.0 13.60 1.0 5.0 17.8 22.0 TPSMA18 BDP 16.20 19.80 1.0 14.50 1.0 5.0 15.1 26.5 TPSMA18A BEP 17.10 18.90 1.0 15.30 1.0 5.0 15.9 25.5 TPSMA20 BFP 18.00 22.00 1.0 16.20 1.0 5.0 13.7 29.1 TPSMA20A BGP 19.00 21.00 1.0 17.10 1.0 5.0 14.4 27.7 TPSMA22 BHP 19.80 24.20 1.0 17.80 1.0 5.0 12.5 31.9 TPSMA22A BKP 20.90 23.10 1.0 18.80 1.0 5.0 13.1 30.6 TPSMA24 BLP 21.60 26.40 1.0 19.40 1.0 5.0 11.5 34.7 TPSMA24A BMP 22.80 25.20 1.0 20.50 1.0 5.0 12.0 33.2 TPSMA27 BNP 24.30 29.70 1.0 21.80 1.0 5.0 10.2 39.1 TPSMA27A BPP 25.70 28.40 1.0 23.10 1.0 5.0 10.7 37.5 TPSMA30 BQP 27.00 33.00 1.0 24.30 1.0 5.0 9.2 43.5 TPSMA30A BRP 28.50 31.50 1.0 25.60 1.0 5.0 9.7 41.4 TPSMA33 BSP 29.70 36.30 1.0 26.80 1.0 5.0 8.4 47.0 TPSMA33A BTP 31.40 34.70 1.0 28.20 1.0 5.0 8.8 45.7 TPSMA36 BUP 32.40 39.60 1.0 29.10 1.0 5.0 7.7 52.0 TPSMA36A BVP 34.20 37.80 1.0 30.80 1.0 5.0 8.0 49.9 TPSMA39 BWP 35.10 42.90 1.0 31.60 1.0 5.0 7.1 56.4 TPSMA39A BXP 37.10 41.00 1.0 33.30 1.0 5.0 7.4 53.9 TPSMA43 BYP 38.70 47.30 1.0 34.80 1.0 5.0 6.5 61.9 TPSMA43A BZP 40.90 45.20 1.0 36.80 1.0 5.0 6.7 59.3 Notes (1) V BR measured after IT applied for 300 μs, IT = square wave pulse or equivalent (2) Surge current waveform per fig. 3 and derated per fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE C62.35 Revision: 25-Apr-14 Document Number: 88405 2 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TPSMA6.8 thru TPSMA43A www.vishay.com Vishay General Semiconductor ORDERING INFORMATION (Example) PREFERRED P/N TPSMA6.8AHE3_A/H UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY 0.064 H 1800 7" diameter plastic tape and reel 0.064 I 7500 13" diameter plastic tape and reel (1) TPSMA6.8AHE3_A/I (1) DELIVERY MODE Note (1) AEC-Q101 qualified RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted) 150 Non-Repetitive Pulse Waveform shown in Fig. 3 TA = 25 °C IPPM - Peak Pulse Current, % IRSM PPPM - Peak Power (kW) 100 10 1.0 0.2 x 0.2" (5.0 x 5.0 mm) Copper Pad Areas 0.1 0.1 µs td 1.0 µs 10 µs 100 µs 1.0 ms Peak Value IPPM 100 Half Value - IPP IPPM 2 50 10/1000 µs Waveform as defined by R.E.A. td 0 10 ms 0 1.0 td - Pulse Width (s) 3.0 2.0 4.0 t - Time (ms) Fig. 1 - Peak Pulse Power Rating Curve Fig. 3 - Pulse Waveform 10 000 100 Junction Capacitance (pF) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % TJ = 25 °C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM tr = 10 µs 75 50 25 VR measured at Zero Bias 1000 VR measured at Stand-Off, VWM 100 TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p 10 0 0 50 100 150 200 TJ - Initial Temperature (°C) Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature Revision: 25-Apr-14 1 10 100 VBR - Breakdown Voltage (V) Fig. 4 - Typical Junction Capacitance Document Number: 88405 3 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TPSMA6.8 thru TPSMA43A www.vishay.com Vishay General Semiconductor Peak Forward Surge Current (A) 200 TJ = TJ max. 8.3 ms Single Half Sine-Wave 100 50 10 1 5 10 50 100 Number of Cycles at 60 Hz Fig. 5 - Maximum Non-Repetitive Peak Forward Surge Current PACKAGE OUTLINE DIMENSIONS in inches (millimeters) DO-214AC (SMA) Cathode Band Mounting Pad Layout 0.110 (2.79) 0.100 (2.54) 0.065 (1.65) 0.049 (1.25) 0.177 (4.50) 0.157 (3.99) 0.012 (0.305) 0.006 (0.152) 0.060 (1.52) MIN. 0.208 (5.28) REF. 0.090 (2.29) 0.078 (1.98) 0.060 (1.52) 0.030 (0.76) 0.074 (1.88) MAX. 0.066 (1.68) MIN. 0.008 (0.203) 0 (0) 0.208 (5.28) 0.194 (4.93) Revision: 25-Apr-14 Document Number: 88405 4 For technical questions within your region: [email protected], [email protected], [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000