Data Sheet

GTL2034
4-bit GTL to GTL buffer
Rev. 01 — 11 November 2005
Product data sheet
1. General description
The GTL2034 is a 4-bit GTL−/GTL/GTL+ bus buffer.
The GTL2034 GTL inputs and outputs operate up to 3.6 V, allowing the device to be used
in higher voltage open-drain output applications.
2. Features
■
■
■
■
■
■
Operates as a 4-bit GTL−/GTL/GTL+ to GTL−/GTL/GTL+ bus buffer
3.0 V to 3.6 V operation
GTL input and output 3.6 V tolerant
Vref adjustable from 0.5 V to VCC / 2
Partial power-down permitted
ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per
JESD22-A115, and 1000 V CDM per JESD22-CC101
■ Latch-up protection exceeds 500 mA per JESD78
■ Package offered: TSSOP14
3. Quick reference data
Table 1:
Quick reference data
Tamb = 25 °C
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
GTL; BIn to BOn;
CL = 50 pF; VCC = 3.3 V
-
3.1
8
ns
-
4.1
10
ns
GTL; outputs disabled;
VI/O = 0 V or 3.0 V
-
4.5
-
pF
tPLH
LOW-to-HIGH propagation delay
tPHL
HIGH-to-LOW propagation delay
Ci
input capacitance
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
4. Ordering information
Table 2:
Ordering information
Type number
GTL2034PW
Package
Name
Description
Version
TSSOP14
plastic thin shrink small outline package; 14 leads;
body width 4.4 mm
SOT402-1
4.1 Ordering options
Table 3:
Ordering options
Type number
Topside mark
Temperature range
GTL2034PW
GTL2034
Tamb = −40 °C to +85 °C
5. Functional diagram
GTL2034
BI0
BO0
BI1
BO1
BI2
BO2
BI3
BO3
VREF
002aab148
Fig 1. Logic diagram of GTL2034
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
2 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
6. Pinning information
6.1 Pinning
n.c.
1
BO0
2
14 VCC
13 BI0
12 BI1
BO1
3
VREF
4
BO2
5
10 BI2
BO3
6
9
BI3
GND
7
8
GND
GTL2034PW
11 GND
002aab147
Fig 2. Pin configuration for TSSOP14
6.2 Pin description
Table 4:
Pin description
Symbol
Pin
Description
n.c.
1
not connected
BO0
2
data outputs (GTL)
BO1
3
BO2
5
BO3
6
BI0
13
BI1
12
BI2
10
BI3
9
VREF
4
GTL reference voltage
GND
7, 8, 11
ground (0 V)
VCC
14
positive supply voltage
data inputs (GTL)
7. Functional description
Refer to Figure 1 “Logic diagram of GTL2034”.
7.1 Function table
Table 5:
Function table
Input/output
BIn (GTL)
BOn (GTL)
Input
BOn = BIn
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
3 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
8. Limiting values
Table 6:
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). [1]
Voltages are referenced to GND (ground = 0 V).
Symbol
Parameter
VCC
supply voltage
IIK
input clamping current
Conditions
Min
Max
Unit
−0.5
+4.6
V
VI < 0 V
-
−50
mA
+4.6
V
VI
input voltage
B port
−0.5 [2]
IOK
output clamping current
VO < 0 V
-
−50
mA
−0.5 [2]
+4.6
V
-
80
mA
−60
+150
°C
VO
output voltage
output in OFF or
HIGH state; B port
IOL
LOW-state output current [3]
B port
[4]
storage temperature
Tstg
[1]
Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those indicated under Section 9 “Recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
[2]
The input and output negative voltage ratings may be exceeded if the input and output clamp current ratings are observed.
[3]
Current into any output in the LOW state.
[4]
The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction
temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150 °C.
9. Recommended operating conditions
Table 7:
Recommended operating conditions
Unused inputs must be held HIGH or LOW to prevent them from floating.
Symbol
Parameter
VCC
supply voltage
VTT
termination voltage [1]
reference voltage
Vref
Conditions
Min
Typ
Max
Unit
3.0
-
3.6
V
GTL−
0.85
0.9
0.95
V
GTL
1.14
1.2
1.26
V
GTL+
1.35
1.5
1.65
V
overall
0.5
2⁄ V
3 TT
VCC / 2
V
GTL−
0.5
0.6
0.63
V
GTL
0.76
0.8
0.84
V
GTL+
0.87
1.0
1.10
V
VI
input voltage
B port
0
VTT
3.6
V
VIH
HIGH-state input voltage
B port
Vref + 0.050
-
-
V
VIL
LOW-state input voltage
B port
-
-
Vref − 0.050
V
IOL
LOW-state output current
B port
-
-
40
mA
Tamb
ambient temperature
operating in free air
−40
-
+85
°C
[1]
VTT maximum of 3.6 V with resistor sized so IOL maximum is not exceeded.
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
4 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
10. Static characteristics
Table 8:
Static characteristics
Recommended operating conditions; voltages are referenced to GND (ground = 0 V). Tamb = −40 °C to +85 °C
Symbol
Parameter
Conditions
[2]
Min
Typ [1]
Max
Unit
-
0.2
0.4
V
VOL
LOW-state output voltage
B port; VCC = 3.0 V; IOL = 40 mA
II
input current
B port; VCC = 3.6 V;
VI = VTT or GND
-
-
±1
µA
ILO
output leakage current
B port; VCC = 3.6 V; VO = VTT
-
-
±1
µA
ICC
quiescent supply current
B port; VCC = 3.6 V;
VI = VCC or GND; IO = 0 mA
-
4
8
mA
Ci
input capacitance
port BIn; VO = VTT or 0 V
-
4.5
-
pF
Co
output capacitance
port BOn; VO = VTT or 0 V
-
5.5
-
pF
[1]
All typical values are measured at VCC = 3.3 V and Tamb = 25 °C.
[2]
The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
5 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
10.1 Performance curves
002aab144
1200
Vth+
and
Vth−
(mV)
1000
Vth+
Vth−
Vref
800
Vth+
Vth−
Vref
800
600
400
0.5
002aab145
1200
Vth+
and
Vth−
(mV)
1000
600
0.6
0.7
0.9
0.8
400
0.5
1.0
Vref (V)
a. VCC = 3.0 V; Tamb = −40 °C
0.6
0.7
0.8
0.9
1.0
Vref (V)
b. VCC = 3.3 V; Tamb = 25 °C
002aab146
1200
Vth+
and
Vth−
(mV)
1000
Vth+
Vth−
Vref
800
600
400
0.5
0.6
0.7
0.8
0.9
1.0
Vref (V)
c. VCC = 3.6 V; Tamb = 85 °C
Fig 3. GTL Vth+ and Vth− versus Vref
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
6 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
11. Dynamic characteristics
Table 9:
Dynamic characteristics
VCC = 3.3 V ± 0.3 V
Symbol
Parameter
Conditions
Min
Typ [1]
Max
Unit
BIn to BOn;
see Figure 4
-
2.8
8
ns
-
5.2
10
ns
BIn to BOn;
see Figure 4
-
3.1
8
ns
-
4.1
10
ns
BIn to BOn;
see Figure 4
-
3.3
8
ns
-
3.6
10
ns
GTL−; Vref = 0.6 V; VTT = 0.9 V
tPLH
LOW-to-HIGH propagation delay
tPHL
HIGH-to-LOW propagation delay
GTL; Vref = 0.8 V; VTT = 1.2 V
tPLH
LOW-to-HIGH propagation delay
tPHL
HIGH-to-LOW propagation delay
GTL+; Vref = 1.0 V; VTT = 1.5 V
tPLH
LOW-to-HIGH propagation delay
tPHL
HIGH-to-LOW propagation delay
[1]
All typical values are at VCC = 3.3 V and Tamb = 25 °C.
11.1 Waveforms
VM = Vref for B ports.
VTT
input
Vref
Vref1
1/ V
3 TT
tPLH
tpulse
tPHL
VOH
3.0 V
VM
output
VM
Vref
Vref2
VOL
0V
002aab149
002aab140
a. Pulse duration
b. Propagation delay times
Fig 4. Voltage waveforms
12. Test information
VTT
VCC
PULSE
GENERATOR
VI
25 Ω
VO
D.U.T.
RT
CL
30 pF
002aab143
CL = load capacitance; includes jig and probe capacitance.
RT = termination resistance; should be equal to Zo of pulse generator.
Fig 5. Load circuit for B outputs
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
7 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
13. Package outline
TSSOP14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm
SOT402-1
E
D
A
X
c
y
HE
v M A
Z
8
14
Q
(A 3)
A2
A
A1
pin 1 index
θ
Lp
L
1
7
e
detail X
w M
bp
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (2)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
1.1
0.15
0.05
0.95
0.80
0.25
0.30
0.19
0.2
0.1
5.1
4.9
4.5
4.3
0.65
6.6
6.2
1
0.75
0.50
0.4
0.3
0.2
0.13
0.1
0.72
0.38
8
o
0
o
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic interlead protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
SOT402-1
REFERENCES
IEC
JEDEC
JEITA
MO-153
EUROPEAN
PROJECTION
ISSUE DATE
99-12-27
03-02-18
Fig 6. Package outline SOT402-1 (TSSOP14)
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
8 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
14. Soldering
14.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
14.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 seconds and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 °C to 270 °C depending on solder paste
material. The top-surface temperature of the packages should preferably be kept:
• below 225 °C (SnPb process) or below 245 °C (Pb-free process)
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness ≥ 2.5 mm
– for packages with a thickness < 2.5 mm and a volume ≥ 350 mm3 so called
thick/large packages.
• below 240 °C (SnPb process) or below 260 °C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
14.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
• Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
• For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
parallel to the transport direction of the printed-circuit board;
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
9 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
– smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
• For packages with leads on four sides, the footprint must be placed at a 45° angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250 °C
or 265 °C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
14.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300 °C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 seconds to 5 seconds between 270 °C and 320 °C.
14.5 Package related soldering information
Table 10:
Suitability of surface mount IC packages for wave and reflow soldering methods
Package [1]
Soldering method
Wave
Reflow [2]
BGA, HTSSON..T [3], LBGA, LFBGA, SQFP,
SSOP..T [3], TFBGA, VFBGA, XSON
not suitable
suitable
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
not suitable [4]
suitable
PLCC [5], SO, SOJ
suitable
suitable
not
recommended [5] [6]
suitable
SSOP, TSSOP, VSO, VSSOP
not
recommended [7]
suitable
CWQCCN..L [8], PMFP [9], WQCCN..L [8]
not suitable
LQFP, QFP, TQFP
[1]
For more detailed information on the BGA packages refer to the (LF)BGA Application Note (AN01026);
order a copy from your Philips Semiconductors sales office.
[2]
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal or
external package cracks may occur due to vaporization of the moisture in them (the so called popcorn
effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit
Packages; Section: Packing Methods.
[3]
These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no
account be processed through more than one soldering cycle or subjected to infrared reflow soldering with
peak temperature exceeding 217 °C ± 10 °C measured in the atmosphere of the reflow oven. The package
body peak temperature must be kept as low as possible.
9397 750 13543
Product data sheet
not suitable
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
10 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
[4]
These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the
solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink
on the top side, the solder might be deposited on the heatsink surface.
[5]
If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
[6]
Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is
definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
[7]
Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger
than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
[8]
Image sensor packages in principle should not be soldered. They are mounted in sockets or delivered
pre-mounted on flex foil. However, the image sensor package can be mounted by the client on a flex foil by
using a hot bar soldering process. The appropriate soldering profile can be provided on request.
[9]
Hot bar soldering or manual soldering is suitable for PMFP packages.
15. Abbreviations
Table 11:
Abbreviations
Acronym
Description
CDM
Charged Device Model
ESD
ElectroStatic Discharge
GTL
Gunning Transceiver Logic
HBM
Human Body Model
MM
Machine Model
TTL
Transistor-Transistor Logic
16. Revision history
Table 12:
Revision history
Document ID
Release date
Data sheet status
Change notice
Doc. number
Supersedes
GTL2034_1
20051111
Product data sheet
-
9397 750 13543
-
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
11 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
17. Data sheet status
Level
Data sheet status [1]
Product status [2] [3]
Definition
I
Objective data
Development
This data sheet contains data from the objective specification for product development. Philips
Semiconductors reserves the right to change the specification in any manner without notice.
II
Preliminary data
Qualification
This data sheet contains data from the preliminary specification. Supplementary data will be published
at a later date. Philips Semiconductors reserves the right to change the specification without notice, in
order to improve the design and supply the best possible product.
III
Product data
Production
This data sheet contains data from the product specification. Philips Semiconductors reserves the
right to make changes at any time in order to improve the design, manufacturing and supply. Relevant
changes will be communicated via a Customer Product/Process Change Notification (CPCN).
[1]
Please consult the most recently issued data sheet before initiating or completing a design.
[2]
The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at
URL http://www.semiconductors.philips.com.
[3]
For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
18. Definitions
customers using or selling these products for use in such applications do so
at their own risk and agree to fully indemnify Philips Semiconductors for any
damages resulting from such application.
Short-form specification — The data in a short-form specification is
extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Right to make changes — Philips Semiconductors reserves the right to
make changes in the products - including circuits, standard cells, and/or
software - described or contained herein in order to improve design and/or
performance. When the product is in full production (status ‘Production’),
relevant changes will be communicated via a Customer Product/Process
Change Notification (CPCN). Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no
license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are
free from patent, copyright, or mask work right infringement, unless otherwise
specified.
Limiting values definition — Limiting values given are in accordance with
the Absolute Maximum Rating System (IEC 60134). Stress above one or
more of the limiting values may cause permanent damage to the device.
These are stress ratings only and operation of the device at these or at any
other conditions above those given in the Characteristics sections of the
specification is not implied. Exposure to limiting values for extended periods
may affect device reliability.
Application information — Applications that are described herein for any
of these products are for illustrative purposes only. Philips Semiconductors
make no representation or warranty that such applications will be suitable for
the specified use without further testing or modification.
20. Trademarks
19. Disclaimers
Notice — All referenced brands, product names, service names and
trademarks are the property of their respective owners.
Life support — These products are not designed for use in life support
appliances, devices, or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors
21. Contact information
For additional information, please visit: http://www.semiconductors.philips.com
For sales office addresses, send an email to: [email protected]
9397 750 13543
Product data sheet
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Rev. 01 — 11 November 2005
12 of 13
GTL2034
Philips Semiconductors
4-bit GTL to GTL buffer
22. Contents
1
2
3
4
4.1
5
6
6.1
6.2
7
7.1
8
9
10
10.1
11
11.1
12
13
14
14.1
14.2
14.3
14.4
14.5
15
16
17
18
19
20
21
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Quick reference data . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2
Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2
Pinning information . . . . . . . . . . . . . . . . . . . . . . 3
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3
Functional description . . . . . . . . . . . . . . . . . . . 3
Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recommended operating conditions. . . . . . . . 4
Static characteristics. . . . . . . . . . . . . . . . . . . . . 5
Performance curves . . . . . . . . . . . . . . . . . . . . . 6
Dynamic characteristics . . . . . . . . . . . . . . . . . . 7
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Test information . . . . . . . . . . . . . . . . . . . . . . . . . 7
Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 8
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Introduction to soldering surface mount
packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . . 9
Wave soldering . . . . . . . . . . . . . . . . . . . . . . . . . 9
Manual soldering . . . . . . . . . . . . . . . . . . . . . . 10
Package related soldering information . . . . . . 10
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . 11
Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 12
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Contact information . . . . . . . . . . . . . . . . . . . . 12
© Koninklijke Philips Electronics N.V. 2005
All rights are reserved. Reproduction in whole or in part is prohibited without the prior
written consent of the copyright owner. The information presented in this document does
not form part of any quotation or contract, is believed to be accurate and reliable and may
be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under
patent- or other industrial or intellectual property rights.
Date of release: 11 November 2005
Document number: 9397 750 13543
Published in The Netherlands