CRCW....-37 Vishay Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors FEATURES • High pulse performance (time/power) • Metal glaze on high quality ceramic • Protective overglaze • Lead (Pb)-bearing solder contacts on Ni barrier layer STANDARD ELECTRICAL SPECIFICATIONS SIZE MODEL INCH METRIC POWER RATING P70 °C W RATED VOLTAGE V CRCW1206-37 1206 3216 0.25 200 CRCW1210-37 1210 3225 0.33 200 CRCW2512-37 2512 6332 1.0 500 TEMPERATURE TOLERANCE RESISTANCE RANGE E-SERIES COEFFICIENT % Ω ppm/K ± 200 ± 10 5R1 to 10M E24 Notes: • These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime • Marking and packaging: see appropriate catalog or web pages • Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material TECHNICAL SPECIFICATIONS PARAMETER UNIT CRCW1206-37 CRCW1210-37 CRCW2512-37 Rated Dissipation at P70 (2) W 0.25 0.33 1.0 Rated Voltage Umax. AC/DC V 200 200 500 Insulation Voltage Uins (1 Min) V Thermal Resistance (1) K/W Category Temperature Range °C Weight mg > 300 ≤ 220 ≤ 140 ≤ 65 - 55 to + 155 10 16 40.5 Notes: (1) For size 1206 the measuring conditions are in acc. to EN 140401-802. For all other sizes the result depends on the solder pad dimensions. (2) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded. www.vishay.com 1 For technical questions, contact: [email protected] Document Number: 20044 Revision: 28-May-08 CRCW....-37 Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors Vishay PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: CRCW120622K0KNTA37 (1) C R C W 1 2 0 6 2 2 K 0 K N T A 3 7 MODEL VALUE TOLERANCE TCR PACKAGING (2) SPECIAL CRCW1206 CRCW1210 CRCW2512 R = Decimal K = Thousand M = Million K = ± 10 % N = ± 200 ppm/K TA TB TC TG TH TI TL 37 = Non-trimmed PRODUCT DESCRIPTION: CRCW1206-37 223 K 200 RT1 CRCW-37 223 K 200 200 MODEL RESISTANCE VALUE TOLERANCE TCR PACKAGING (2) CRCW1206-37 CRCW1210-37 CRCW2512-37 685 = 6.8 MΩ 224 = 220 kΩ K = ± 10 % ± 200 ppm/K RT1 RT5 RT6 R67 R82 RG1 R20 Notes: (1) Preferred (2) Please way for ordering products is by use of the PART NUMBER refer to table PACKAGING, see below PACKAGING REEL PACKAGING CODE MODEL D25/CRCW1206-37 CRCW1210-37 CRCW2512-37 Document Number: 20044 Revision: 28-May-08 TAPE WIDTH 8 mm 12 mm 12 mm DIAMETER PITCH PIECES/ REEL PART NUMBER PRODUCT DESC. PAPER BLISTER PAPER BLISTER TI RT1 RG1 180 mm/7" 4 mm 5000 TA 285 mm/11.25" 4 mm 10 000 TB 330 mm/13" 4 mm 20 000 TC 180 mm/7" 4 mm 5000 TA RT1 285 mm/11.25" 4 mm 10 000 TB RT5 330 mm/13" 4 mm 20 000 TC RT6 8 mm 2000 TG R67 4 mm 4000 TH R82 RT5 TL RT6 R20 180 mm/7" For technical questions, contact: [email protected] www.vishay.com 2 CRCW....-37 Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors Vishay DIMENSIONS SOLDER PAD DIMENSIONS [in millimeters] SIZE DIMENSIONS [in millimeters] REFLOW SOLDERING INCH METRIC L 1206 3216 3.2 1210 3225 2512 6332 WAVE SOLDERING W H T1 T2 a b l a b l 1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 1.7 2.0 1.1 1.7 2.3 3.2 ± 0.2 2.5 ± 0.2 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 2.5 2.0 1.1 2.5 2.2 6.3 ± 0.2 3.15 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 3.2 5.2 1.2 3.2 5.2 + 0.10 - 0.20 Pulse Power (W) FUNCTIONAL PERFORMANCE 10 000 1000 100 10 1 10-1 10-2 10-6 10-5 10-4 10-3 10-2 10-1 1 10 100 Pulse Duration (s) Rated Power in % Maximum pulse dissipation as a function of the pulse duration for one.pulse loading of CRCW...-37 resistors 120 100 80 60 40 20 0 - 55 Derating www.vishay.com 3 - 25 0 25 50 75 70 100 125 155 175 Ambient Temperature in °C For technical questions, contact: [email protected] Document Number: 20044 Revision: 28-May-08 CRCW....-37 Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 REQUIREMENTS TEST (clause) STABILITY CLASS 2 OR BETTER CONDITIONS OF TEST Stability for product types: 5.1 Ω to 10 MΩ CRCW....-37 Resistance (4.5) - ± 10 % 20/- 55/20 °C and 20/125/20 °C ± 200 ppm/K U = 2.5 x (P70 x R)1/2 ≤ 2 x Umax.; Duration: according the style ± (0.25 % R + 0.05 Ω) Aging 4 h at 155 °C, dryheat solder bath method; 235 °C; 2 s visual examination Good tinning (≥ 95 % covered) no visible damage Resistance to soldering heat (4.18.2) Solder bath method; (260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 Ω) Rapid change of temperature (4.19) 30 min at LCT = - 55 °C; 30 min at UCT = 125 °C; 5 cycles ± (0.25 % R + 0.05 Ω) (40 ± 2) °C; 56 days; (93 ± 3) % RH ± (1 % R + 0.05 Ω) Climatic sequence (4.23) 16 h at UCT = 125 °C; 1 cycle at 55 °C; 2 h at LCT = - 55 °C; 1 h/1 kPa at 15 °C to 35 °C; 5 cycles at 55 °C U = (P70 × R)1/2 U = Umax.; whichever is less severe ± (1 % R + 0.05 Ω) Endurance at 70 °C (4.25.1) U = (P70 × R)1/2 U = Umax.; whichever is less severe 1.5 h ON; 0.5 h OFF; 70 °C; 1000 h ± (1 % R + 0.05 Ω) Extended endurance (4.25.1.8) Duration extended to 8000 h ± (2 % R + 0.1 Ω) UCT = 125 °C; 1000 h ± (1 % R + 0.05 Ω) Temperature coefficient (4.8.4.2) Overload (4.13) Solderability (4.17.5) Damp heat, steady state (4.24) Endurance at upper category temperature (4.25.3) APPLICABLE SPECIFICATIONS • EN 60115-1 Generic Specification • EN 140400 Sectional Specification • EN 140401-802 Detail Specification • IEC 60068-2-X Variety of environmental test procedures • IEC 60286-3 Packaging of SMD components Document Number: 20044 Revision: 28-May-08 For technical questions, contact: [email protected] www.vishay.com 4 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000