HVR25, HVR37 www.vishay.com Vishay BCcomponents High Ohmic (up to 10 M)/High Voltage (up to 3.5 kV) Metal Film Leaded Resistors FEATURES • Technology: Metal film • High pulse loading (up to 10 kV) capability • Small size (0207/0411) • Compatible with lead (Pb)-free and lead containing soldering processes • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • Power supplies • Electronic ballast • White goods A homogenous film of metal alloy is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to the end-caps. The resistors are coated with a blue, non-flammable lacquer, which provides electrical, mechanical, and climatic protection. • Television TECHNICAL SPECIFICATIONS DESCRIPTION UNIT HVR25 HVR37 Resistance Range 100K to 10M 100K to 10M Resistance Tolerance % Temperature Coefficient ± 5; E24 series ± 1; E24/E96 series ± 5; E24 series ± 1; E24/E96 series 200 ppm/K Climatic Category (LCT/UCT/days) 55/155/56 Rated Dissipation, P70 W 0.25 0.5 1600 3500 1150 2500 Maximum Permissible Voltage Umax. DC V RMS Basic Specification IEC 60115-1 Stability After: Load (1000 h, P70) Long Term Damp Heat Test (56 days) Soldering (10 s, 260 °C) Revision: 26-May-14 ± (5 % R + 0.1 ± (1.5 % R + 0.1 ± (5 % R + 0.1 ± (1.5 % R + 0.1 ± (1.5 % R + 0.1 ± (1.5 % R + 0.1 ± (1.5 % R + 0.1 ± (1.5 % R + 0.1 ± (1 % R + 0.1 ± (1 % R + 0.1 ± (1 % R + 0.1 ± (1 % R + 0.1 Document Number: 30260 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 HVR25, HVR37 www.vishay.com Vishay BCcomponents PART NUMBER AND PRODUCT DESCRIPTION (1) Part Number: HVR2500001503JA100 H V R 2 5 0 0 0 0 1 5 0 3 J A 1 0 0 MODEL/SIZE VARIANT TCR/MATERIAL VALUE TOLERANCE PACKAGING (2) SPECIAL HVR2500 HVR3700 0 = Neutral 0 = Standard 3 digit value 1 digit multiplier MULTIPLIER 3 = *103 4 = *104 5 = *105 F=1% J=5% A1 A5 R5 N4 Up to 2 digits 00 = Standard HVR25 5% A1 150K Model TOLERANCE PACKAGING (2) RESISTANCE VALUE HVR25 HVR37 ±1% ±5% A1 A5 R5 N4 150K = 150 k 4M64 = 4.64 M Product Description: HVR25 5 % A1 150K Notes (1) The PART NUMBER is shown to facilitate the introduction of the unified part numbering system (2) Please refer to table PACKAGING, see next page PACKAGING AMMO PACK MODEL REEL TAPING PIECES CODE PIECES CODE 5000 A5 5000 R5 1000 A1 Radial 4000 N4 Axial, 52 mm 1000 A1 5000 R5 Axial, 52 mm HVR25 HVR37 DIMENSIONS L1 ØD Ød L2 A DIMENSIONS - Resistor types, mass and relevant physical dimensions TYPE L1 max. (mm) L2 max. (mm) Dmax. (mm) Ød (mm) A (mm) MASS (mg) HVR25 6.5 7.5 2.5 0.58 0.05 52.5 1.5 220 HVR37 10 12 4 0.70 0.03 52.5 1.5 500 Revision: 26-May-14 Document Number: 30260 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 HVR25, HVR37 www.vishay.com Vishay BCcomponents PRODUCTS WITH RADIAL LEADS (HVR25) P2 P H1 H H0 L L1 W0 W F P0 P1 D0 DIMENSIONS - Radial taping SYMBOL PARAMETER VALUE TOLERANCE UNIT P Pitch of components 12.7 1.0 mm P0 Feed-hole pitch 12.7 0.2 mm P1 Feed-hole centre to lead at topside at the tape 3.85 0.5 mm P2 Feed-hole center to body center 6.35 1.0 mm F Lead-to-lead distance 4.8 0.7/-0 mm W Tape width 18.0 0.5 mm W0 Minimum hold down tape width 5.5 - mm H1 Component height 29 Max. mm H0 Lead wire clinch height 16.5 0.5 mm H Height of component from tape center 19.5 1 mm D0 Feed-hole diameter 4.0 0.2 mm L Maximum length of snipped lead 11.0 - mm L1 Minimum lead wire (tape portion) shortest lead 2.5 - mm Note • Please refer document number 28721 “Packaging” for more detail MARKING The nominal resistance and tolerance are marked on the resistor using four or five colored bands in accordance with IEC 60062, marking codes for resistors and capacitors. Standard values of nominal resistance are taken from the E24 and E24/E96 series for resistors with a tolerance of 5 % or 1 % respectively. The values of the E24/E96 series are in accordance with IEC 60063. Yellow and grey are used instead of gold and silver because metal particles in the lacquer could affect high-voltage properties. Revision: 26-May-14 Document Number: 30260 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 HVR25, HVR37 www.vishay.com Vishay BCcomponents Power Dissipation P FUNCTIONAL PERFORMANCE 100 0 - 55 0 70 155 Ambient temperature ϑ amb Derating - Standard Operation Maximum dissipation (Pmax.) in percentage of rated power as a function of ambient temperature (Tamb) PULSE LOADING CAPABILITY Note • Maximum allowed peak pulse voltage in accordance with IEC 60065, 14.1.a; 50 discharges from a 1 nF capacitor charged to Umax.; 12 discharges/min 12 11 10 Ûmax. (kV) 9 8 7 6 HVR25 R = (4.0 % R + 0.1 ) 5 4 10-2 10-1 100 101 102 R (MΩ) 12 11 10 Ûmax. (kV) 9 8 7 6 HVR37 For 5 % tolerance R = (4.0 % R + 0.1 ) For 1 % tolerance R = (2.0 % R + 0.1 ) 5 4 10-2 10-1 100 101 102 R (MΩ) Revision: 26-May-14 Document Number: 30260 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 HVR25, HVR37 www.vishay.com Vishay BCcomponents TESTS AND REQUIREMENTS Essentially all tests are carried out in accordance with IEC 60115-1, category 55/155/56 (rated temperature range - 55 °C to + 155 °C; damp heat, long term, 56 days) and along the lines of IEC 60068-2-xx test method. The tests are carried out under standard atmospheric conditions according to IEC 60068-1, 5.3 unless otherwise specified. In some instances deviations from IEC recommendations were necessary for our method of specifying. PERFORMANCE IEC 60115-1 CLAUSE 4.8 4.25.1 4.24 IEC 60068-2-xx TEST METHOD TEST - Temperature coefficient - 78 (Cab) 4.23 PROCEDURE HVR25 Endurance at 70 °C Damp heat, steady state Between -55 °C and +155 °C for 5 % tolerance (5 % R + 0.1 ) (1.5 % R + 0.1 ) 56 days; 40 °C; 90 % to 95 % RH loaded with 0.01 P70 for 5 % tolerance (5 % R + 0.1 ) for 1 % tolerance (1.5 % R + 0.1 ) Climatic sequence Dry heat 16 h, 155 °C 4.23.3 30 (Db) Damp heat, cyclic 24 h; 25 °C to 55 °C 90 % to 100 % RH; 1 cycle 4.23.4 1 (Aa) Cold 2 h, -55 °C 4.23.6 30 (Db) Damp heat, (accelerated) remaining cycles 5 days; 25 °C to 55 °C 90 to 100 % RH 14 (Na) Rapid change of temperature 30 min at LCT; 30 min at UCT; LCT = -55 °C; UCT = 155 °C; 5 cycles 4.12 - - Short time overload Noise No visual damage (1 % R + 0.1 ) Room temperature; dissipation 6.25 x P70 (voltage not more than 2 x limiting voltage, 10 000 Vmax.); 10 cycles 5 s ON and 45 s OFF for 5 % tolerance (2 % R + 0.1 ) for 1 % tolerance (1 % R + 0.1 ) IEC 60195 21 (Ua1) Tensile all samples Load 10 N; 10 s 4.16.3 21 (Ub) Bending half number of samples Load 5 N; 4 x 90° 4.16.4 21 (Uc) Torsion other half of samples 3 x 360° in opposite direction Vibration Frequency 10 Hz to 500 Hz; displacement 1.5 mm or acceleration 10 g; 3 directions; total 6 h (3 x 2 h) 4.22 (1.5 % R + 0.1 ) Max. 5 μV/V Max. 2.5 μV/V Robustness of terminations: 4.16 4.16.2 200 ppm/K for 1 % tolerance 2 (Ba) 4.13 HVR37 1000 h; loaded with P70 or Umax.; 1.5 h ON; 0.5 h OFF 4.23.2 4.19 REQUIREMENTS PERMISSIBLE CHANGE (R) 6 (Fc) Revision: 26-May-14 No damage (1 % R + 0.1 ) (1.0 % R+ 0.1 ) Document Number: 30260 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 HVR25, HVR37 www.vishay.com Vishay BCcomponents PERFORMANCE IEC 60068-2-xx TEST METHOD TEST 4.17 20 (Ta) Solderability (after ageing) 2 s; 235 °C: Solder bath method; SnPb40 3 s; 245 °C: Solder bath method; SnAg3Cu0.5 Good tinning ( 95 % covered); no visible damage 4.18 20 (Tb) Resistance to soldering heat Thermal shock: 10 s; 260 °C; 3 mm from body (1 % R + 0.1 ) 4.29 45 (XA) Component solvent resistance Isopropyl alcohol No visible damage 4.6.11 - Insulation resistance U = 500 VDC during 1 min, V-block method Rins min. 104 M 4.7 - Voltage proof on insulation URMS = 700 V during 1 min, V-block method No flashover or breakdown IEC 60115-1 CLAUSE REQUIREMENTS PERMISSIBLE CHANGE (R) PROCEDURE HVR25 HVR37 12NC INFORMATION FOR HISTORICAL CODING REFERENCE ONLY Last Digit of 12NC Indicating Resistance Decade • The resistors have a 12 digit ordering code starting with 2306 • The next 4 or 5 digits indicate the resistor type and packaging RESISTANCE DECADE (5 %) RESISTANCE DECADE (1 %) LAST DIGIT • For 5 % tolerance the last 3 digits indicate the resistance value: 100 k to 910 k 100 k to 976 k 4 1 M to 9.1 M 1 M to 9.76 M 5 = 10 M = 10 M 6 - The first 2 digits indicate the resistance value - The last digit indicates the resistance decade in accordance with table 12NC Example • For 1 % tolerance the last 4 digits indicate the resistance value: HVR25, 150 k, 5 %, ammopack 1000 pieces is 2306 241 13154 - The first 3 digits indicate the resistance value - The last digit indicates the resistance decade in accordance with table 12NC - resistor type and packaging 2306 ... ..... DESCRIPTION BANDOLIER ON REEL BANDOLIER IN AMMOPACK RADIAL TAPED TYPE TAPE WIDTH TOLERANCE 1000 UNITS 5000 UNITS 5000 UNITS 4000 UNITS HVR25 HVR37 Revision: 26-May-14 52.5 52.5 5% 241 36... 241 13... 241 53... 241 23.... 1% 241 0.... 241 8.... 241 7.... 241 6.... 5% - 242 13... - 242 23... 1% - 242 8.... - 242 6.... Document Number: 30260 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000