D AP, CRCW-AP Vishay Draloric Thick Film, Rectangular Chip Resistors for Conductive Gluing FEATURES • • • • • AgPd-Terminations for conductive gluing Stability ΔR/R = 1 % for 1000 h at 70 °C Metal glaze on high quality ceramic Compliant to RoHS directive 2002/95/EC Halogen-free according to IEC 61249-2-21 definition STANDARD ELECTRICAL SPECIFICATIONS SIZE MODEL INCH METRIC D10 AP 0402 RR 1005M D11 AP 0603 RR 1608M D12 AP 0805 RR 2012M D25 AP 1206 RR 3216M CRCW1210-AP 1210 RR 3225M CRCW1218-AP 1218 RR 3246M CRCW2010-AP 2010 RR 5025M CRCW2512-AP 2512 RR 6332M RATED DISSIPATION P70 W LIMITING ELEMENT VOLTAGE Umax. AC/DC TEMPERATURE COEFFICIENT ppm/K TOLERANCE % RESISTANCE RANGE Ω SERIES ±1 ±5 100R to 10M 10R to 10M E24; E96 E24 ±1 ±5 18R to 10M 3R6 to 10M E24; E96 E24 ±1 ±5 18R to 10M 3R6 to 10M E24; E96 E24 ±1 ±5 18R to 10M 3R6 to 10M E24; E96 E24 ±1 ±5 18R to 10M 3R6 to 10M E24; E96 E24 ±1 ±5 18R to 2M2 3R6 to 2M2 E24; E96 E24 ±1 ±5 18R to 10M 3R6 to 10M E24; E96 E24 ±1 ±5 18R to 10M 3R6 to 10M E24; E96 E24 ± 100 ± 200 Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 0.5 A ± 100 0.10 75 ± 200 Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 0.7 A ± 100 0.125 150 ± 200 Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 0.8 A ± 100 0.25 200 ± 200 Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 1.0 A ± 100 0.50 200 ± 200 Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 1.5 A ± 100 1.0 200 ± 200 Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 2.0 A ± 100 0.75 400 ± 200 Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 1.8 A ± 100 1.0 500 ± 200 Zero-Ohm-Resistor: Rmax. < 200 mΩ, Imax. = 2.0 A 0.063 50 Notes • These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional time. • Marking and packaging: See datasheet "Surface Mount Resistor Marking" (document number 20020) • Power rating depends on the max. temperature at the joint point, the component placement density and the substrate material. TECHNICAL SPECIFICATIONS PARAMETER Rated dissipation P70 (1) Limiting element voltage Umax. AC/DC Insulation voltage Uins. (1 min) Insulation resistance Category temperature range Failure rate Weight UNIT D10 AP D11 AP D12 AP D25 AP CRCW1210-AP CRCW1218-AP CRCW2010-AP CRCW2512-AP W 0.063 0.1 0.125 0.25 0.5 1.0 0.75 1.0 V 50 75 150 200 200 200 400 500 V > 75 > 100 > 200 > 300 > 300 > 300 > 300 > 300 29.5 25.5 40.5 Ω > 109 °C - 55 to + 155 h-1 mg < 0.1 x 10- 9 0.65 2 5.5 10 16 Note (1) The power dissipation on the resistors generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceed. Document Number: 20038 Revision: 29-Oct-10 For technical questions, contact: [email protected] www.vishay.com 227 D AP, CRCW-AP Thick Film, Rectangular Chip Resistors for Conductive Gluing Vishay Draloric PART NUMBER AND PRODUCT DESCRIPTION (Equal to or smaller than 1206 case size) Part Numbering: D1208058B5620FP5 (1) D 1 2 0 8 0 5 8 B 5 6 2 0 F P 5 MODEL/SIZE SPECIAL CHARACTER TCR VALUE TOLERANCE PACKAGING SPECIAL D100402 D110603 D120805 D251206 8 = AgPd terminations for conductive glueing B = ± 100 ppm/K A = ± 200 ppm/K 0 = Jumper 3 digit value 1 digit multiplier MULTIPLIER 7 = *10-3 8 = *10-2 9 = *10-1 0 = *100 1 = *101 2 = *102 3 = *103 4 = *104 5 = *105 6 = *106 0000 = Jumper F=±1% J=±5% 0 = Jumper P0 P5 PN PZ B5 BN Up to 2 digits Product Description: D12 AP 100 562R 1 % P5 D12 AP 100 562R 1% P5 BVxxxxx MODEL TCR RESISTANCE VALUE TOLERANCE PACKAGING SPECIAL (2) D10 AP D11 AP D12 AP D25 AP ± 100 ppm/K ± 200 ppm/K 49K9 = 49.9 Ω 5R1 = 5.1 kΩ 0R0 = Jumper ±1% ±5% P0 P5 PN PZ B2 B4 B5 BN Customized part number is available on request PART NUMBER AND PRODUCT DESCRIPTION (Equal to or larger than 1210 case size) Part Numbering: CRCW2010562RFKB4AP (1) C R C W 2 0 1 0 5 6 2 R F K B 4 A P MODEL/SIZE SPECIAL CHARACTER TOLERANCE TCR PACKAGING SPECIAL CRCW1210 CRCW1218 CRCW2010 CRCW2512 R = Decimal K = Thousand M = Million 0000 = Jumper F = ± 1.0 % J = ± 5.0 % Z = Jumper K = ± 100 ppm/K N = ± 200 ppm/K 0 = Jumper B2 B4 Up to 2 digits AP = Conductive gluing Product Description: CRCW2010-AP 100 562R 1 % B4 CRCW2010-AP 200 562R 5% B4 BVxxxxx MODEL TCR RESISTANCE VALUE TOLERANCE PACKAGING SPECIAL (2) CRCW1210-AP CRCW1218-AP CRCW2010-AP CRCW2512-AP ± 100 ppm/K ± 200 ppm/K 10R = 10 Ω 562R = 562 Ω 10K = 10 kΩ 1M = 1 MΩ 0R0 = Jumper ±1% ±5% B2 B4 Customized part number is available on request Notes (1) Preferred way for ordering products is by use of the PART NUMBER. (2) Detailed BV number will appear on the packaging label. www.vishay.com 228 For technical questions, contact: [email protected] Document Number: 20038 Revision: 29-Oct-10 D AP, CRCW-AP Thick Film, Rectangular Chip Resistors for Conductive Gluing Vishay Draloric PACKAGING MODEL PAPER TAPE ACC. IEC 60286-3, TYPE I (4) UNIT CRCW1218-AP CRCW2010-AP 180 mm/7" 330 mm/13" 180 mm/7" 285 mm/11.25" 330 mm/13" 180 mm/7" 285 mm/11.25" 330 mm/13" 180 mm/7" 285 mm/11.25" 330 mm/13" 180 mm/7" 285 mm/11.25" 330 mm/13" 180 mm/7" 180 mm/7" CRCW2512-AP 180 mm/7" D10 AP D11 AP D12 AP D25 AP CRCW1210-AP QUANTITY 10 000 50 000 5000 10 000 20 000 5000 10 000 20 000 5000 10 000 20 000 5000 10 000 20 000 BLISTER TAPE ACC. IEC 60286-3, TYPE II CODE P0 PZ P5 P0 PN P5 P0 PN P5 P0 PN P5 P0 PN QUANTITY CODE 5000 B5 20 000 5000 BN B5 20 000 5000 BN B5 15 000 BN 4000 4000 2000 4000 B4 B4 B2 B4 Note (4) Flame treated paper for sizes D10 and D11. Regular paper for sizes D12 and D25. DIMENSIONS SIZE DIMENSIONS in millimeters INCH METRIC L W a b l 0402 1005 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.4 0.6 0.5 0603 1608 1.55 + 0.10 - 0.05 0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.9 0.9 1.0 0805 2012 2.0 + 0.20 - 0.10 1.25 ± 0.15 0.45 ± 0.05 + 0.20 - 0.10 0.3 ± 0.2 0.9 1.3 1.3 1206 3216 3.2 + 0.10 - 0.20 1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 1.1 1.7 2.3 1210 3225 2.5 ± 0.2 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 2.5 2.0 1218 3246 + 0.10 - 0.20 4.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 1.05 4.9 1.9 2010 5025 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 2.5 3.9 2512 6332 6.3 ± 0.2 3.15 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 3.2 5.2 Document Number: 20038 Revision: 29-Oct-10 3.2 ± 0.2 3.2 H T1 GLUING PADS DIMENSIONS in millimeters 0.3 ± 0.2 0.3 T2 0.2 + 0.10 - 0.15 For technical questions, contact: [email protected] www.vishay.com 229 D AP, CRCW-AP Thick Film, Rectangular Chip Resistors for Conductive Gluing Vishay Draloric FUNCTIONAL PERFORMANCE Pulse Load Pmax. (W) Single Pulse 1000 2512 1218 2010 1210 1206 0805 0603 0402 100 10 1 0.1 0.01 10-6 10-5 10-4 10-3 10-2 10-1 1 10 100 Pulse Duration t i (s) Maximum pulse load, single pulse; applicable if P 0 and n < 1000 and Û ≤ Ûmax.; for permissible resistance change equivalent to 8000 h operation Continuous Pulse Load Pmax. (W) Continuous Pulse 1000 2512 1218 2010 1210 1206 0805 0603 0402 100 10 1 0.1 0.01 10-6 10-5 10-4 10-3 10-2 10-1 1 10 100 Pulse Duration t i (s) Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑamb) and Û ≤ Ûmax.; for permissible resistance change equivalent to 8000 h operation Pulse Voltage Û max. (V) Pulse Voltage 2000 1800 2512 1600 1400 2010 1200 1000 800 1206/1210/1218 600 400 0805 0603 200 0402 0 -6 10- 5 10 10- 4 10- 3 10- 2 10- 1 1 10 Pulse Duration t i (s) Maximum pulse voltage, single and continuous pulses; applicable if P ≤ Pmax.; for permissible resistance change equivalent to 8000 h operation www.vishay.com 230 For technical questions, contact: [email protected] Document Number: 20038 Revision: 29-Oct-10 D AP, CRCW-AP Thick Film, Rectangular Chip Resistors for Conductive Gluing Vishay Draloric Fraction of Rated Dissipation in % Derating 120 100 80 60 40 20 0 - 55 - 25 0 25 50 75 70 100 125 155 175 Ambient Temperature in °C Attenuation of 3rd Harmonic A3 in dB Non-Linearity 120 100 80 1206, 2010 0805 60 0603 0402 40 20 0 10 100 1K 10K 100K 1M 10M Resistance Value R in Ω Current Noise A1 in µV/V Current Noise 100 2 040 3 060 5 080 6 120 0 201 10 1 0.1 0.01 100 1K 10K 100K 1M 10M Resistance Value R in Ω Document Number: 20038 Revision: 29-Oct-10 For technical questions, contact: [email protected] www.vishay.com 231 D AP, CRCW-AP Thick Film, Rectangular Chip Resistors for Conductive Gluing Vishay Draloric TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST REQUIREMENTS PERMISSIBLE CHANGE (ΔR) PROCEDURE STABILITY CLASS 2 OR BETTER Stability for product types: D AP, CRCW-AP 4.5 - Resistance - 4.13 - Short time overload U = 2.5 x P 70 x R ≤ 2 x Umax.; duration: Acc. to style 4.8.4.2 - Temperature coefficient (20/- 55/20) °C and (20/125/20) °C 14 (Na) Rapid change of temperature 4.19 4.25.1 4.24 - 3.6 Ω to 10 MΩ ±1% ±5% ± (0.25 % R + 0.05 Ω) ± 100 ppm/K ± 200 ppm/K 30 min. at - 55 °C; 30 min. at 125 °C 5 cycles ± (0.25 % R + 0.05 Ω) 1000 cycles ± (1 % R + 0.05 Ω) U = P 70 x R ≤ Umax.; 1.5 h on; 0.5 h off; Endurance at 70 °C 70 °C; 1000 h ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) 70 °C; 8000 h ± (2 % R + 0.1 Ω) ± (4 % R + 0.1 Ω) 78 (Cab) Damp heat, steady state (40 ± 2) °C; (93 ± 3) % RH; 56 days - Endurance at upper category temperature 155 °C, 1000 h 4.25.3 18 Ω to 10 MΩ ± (1 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) All tests are carried out in accordance with the following specifications: • EN 60115-1, generic specification • EN 140400, sectional specification • EN 140401-802, detail specification • IEC 60068-2, environmental test procedures Packaging of components is done in paper or blister tapes according to IEC 60286-3. www.vishay.com 232 For technical questions, contact: [email protected] Document Number: 20038 Revision: 29-Oct-10 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000