PAM8403 User Guide

PAM8403H
EVB User Guide
PAM8403H-EV Board User Guide
AE Department
1. Revision Information
Date
2008/03/24
2012/07/31
Revision
V1.0
V1.1
Description
Initial Release
Update PCB
Comment
2. PAM8403H General Description
The PAM8403H is a 3W, class-D audio amplifier. It offers low THD+N, allowing it to achieve high-quality sound
reproduction. The new filter less architecture allows the device to drive the speaker directly, requiring no lowpass output filters, thus to save the system cost and PCB area.
With the same numbers of external components,the efficiency of the PAM8403 is much better than that of
class-AB cousins. It can extend the battery life, ideal for portable applications.
3. Key Features

3W Output at 10% THD with a 4Ω Load and 5V

Thermal Shutdown
Power Supply

Few External Components to Save the Space

Filter less, Low Quiescent Current and Low EMI

Low THD+N

Superior Low Noise

Efficiency up to 90%

Short Circuit Protection
and Cost

Pb-Free Package
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8403H
EVB User Guide
4. EV Board Schematic
VDD
3
2
1
MUTE VDD
3
2
1
10
12
5
PVDD
OUT-L-
PAM8403H
INR
OUT-R-
SHDN
OUT-R+
MUTE
PGND
VDD
OUT-L+
PGND
SD
C9
C13
Q?
3
1
16
14
C14
FB3
SPL
FB4
FB1
SPR
FB2
C12
C11
15
C8
C10
VREF
NC
R5
8
INL
2
C4
7
PVDD
R4
Input
C15
4
6
R2
VDD
C7
GND
C5
C2
13
C1
C3
C6
11
R3
R1
9
VDD
Figure 1
5. PAM8403 EB04AB EVB Description
PAM8403 EB04AB is an evaluation board for the PAM8403H, a stereo class-D audio power amplifier. The
board is targeted to be used in providing a simple and convenient evaluation environment for the
PAM8403H. Requires parts, the standard RCA jacks for audio inputs, pin jacks for power supply and signal
outputs etc. on the board make it easy to be evaluated.
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8403H
EVB User Guide
6. EV Board View and Jack Description
Top View
SD Control
Mute Control
R-CH Output
Audio Input
L-CH Output
EV Board Operational Sequence:
Power Supply
a. Connect SD to a high for normal operation
b. Connect audio input from audio input jack
c. Connect the loading (speaker or power resistor) to the output jack
d. Power on: 2.5V to 5.5V DC power supply
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8403H
EVB User Guide
7. EV Board BOM List
Item
Value
C5,C7
0.47µF
C2,C9
1µF
C1,C10
10µF
C4
0.1µF
C3
1µF
C15
R1, R2
R3, R5
C6,C8
FB1,FB2,
FB3,FB4
C11,C12,
C13,C14
220µF
20K
Type
X5R/X7R,
Ceramic/0603
X5R/X7R,
Ceramic/0603
X5R/X7R,
Ceramic/0805
X5R/X7R,
Ceramic/0603
X5R/X7R,
Ceramic/0603
Rating
Description
25V
Input coupling CAP
25V
VDD coupling CAP,
25V
VDD main coupling CAP,
25V
VREF CAP
25V
Decoupling CAP
10V
1%
Decoupling CAP
Input Resistor
For EMI eliminate
components
form a FB-CAP filter
Vender and port
TMK107B7474KA-TR
TMK107B7105KA-T
TMK316AB7106KL-T
UMK212B7104KG-T
TMK107B7105KA-T
NC
NC
330Ω
0805
2A
1nF
0603
25V
Wurth
724 792 037
TMK063B7102KP-F
8. External Components Selection
Input Capacitors (C5, C7)
(1) Form a high pass filter with Ri, and the cut off frequency is fc=1/2*Π*Ri*Ci
(2) Have a tolerance of 10% or better for matching: any mismatch in capacitance causes an importance
mismatch at the corner frequency and below
(3) Low leakage current needed, 0.47µF, X5R/X7R ceramic recommend
Input Resistors (R2, R4)
(1) Limit the closed-loop gain
(2) Form a high pass filter with Ci, and the cut off frequency is fc=1/2*Π*Ri*Ci
(3) 1% tolerance needed for resistor matching to improve CMRR, PSRR
Power Supply decoupling Caps (C2, C3, C9, C1, C10)
(1) Low ESR for good THD, PSRR
(2) 1uF ceramic for higher frequency transients, spikes, or digital hash on the line of PVDD/VDD
(3) Additional 10µF or greater for low frequency noise filtering and serves as a local storage capacitor for
supplying current during large signal transients on the amplifier outputs
(4) Need place very closed to the IC
VREF Capacitor (C4)
(1) 1µF, X5R/X7R ceramic recommended
(2) Place very closed to the device
EMI Eliminate Filter (FB1, FB2, FB3 and FB4)
(1) High impedance at high frequency and very low impedance at low frequency
(2) The current rating is higher than 2A
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8403H
EVB User Guide
9. PCB Layout Guidelines
Grounding
(1) Use plane grounding or separate grounds
(2) Do not use one line connecting power GND and analog GND
(3) Output noise grounds must tie to system ground at the power in exclusively.
(4) Signal currents for the inputs need to be returned to quite ground. This ground only ties to the signal
components and the GND pin.
Power Supply
Others
(1) The power supply capacitors (C2, C3, C9, C1, C10) need to place very close to the PAM8003’s
pins.
(2) Input capacitors (C5, C7) place closed to input pin as near as possible
10. PCB Layout Example
Top Layer
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.
PAM8403H
EVB User Guide
Bottom Layer
This application note contains new product information. Diodes, Inc. reserves the right to modify the product specification without notice.
No liability isassumed as a result of the use of this product. No rights under any patent accompany the sale of the product.