VOL3120 Datasheet

VOL3120
www.vishay.com
Vishay Semiconductors
Low Profile, 2.5 A Output Current IGBT and MOSFET Driver
FEATURES
A 1
5 VCC
• Industrial temperature range: -40 °C to +100 °C
• 2.5 mm low profile package
• Rated for reinforced insulation
4 VO
• 2.5 A minimum peak output current
C 2
22677
• 48 kV/μs minimum common mode rejection
(CMR) at VCM = 1500 V
3 VEE
Shield
• ICC = 2.5 mA maximum supply current
• Under voltage lock-out (UVLO) with hysteresis
DESCRIPTION
• Wide operating VCC range: 15 V to 32 V
The VOL3120 consists of an infrared light emitting diode
optically coupled to an integrated circuit with a power
output stage. This optocoupler is ideally suited for driving
power IGBTs and MOSFETs used in motor control and solar
inverter applications. The high operating voltage range of
the output stage provides the drive voltages required by
gate controlled devices. The voltage and current supplied
by this optocoupler makes it ideally suited for directly driving
high power IGBTs with ratings up to 1000 V / 100 A. The low
profile and small footprint of the VOL3120 makes it an ideal
choice for applications where board space and component
height are at a premium, while still offering a high degree of
isolation performance.
• Floor life: unlimited, MSL 1, according to J-STD-020
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
• Domestic appliance motor drives
• Welding equipment
• Variable speed motor drives
• Induction stove top
• Solar inverters
• Switch mode power supplies (SMPS)
• Uninterruptible power supplies (UPS)
AGENCY APPROVALS
The safety application model number covering all products
in this datasheet is VOL3120. This model number should be
used when consulting safety agency documents.
• UL 1577
• cUL
• CQC
• DIN EN 60747-5-5 (VDE 0884-5)
ORDERING INFORMATION
V
O
L
3
1
PART NUMBER
PACKAGE
LSOP-5
Rev. 1.5, 08-Jan-16
2
0
-
X
0
0
PACKAGE OPTION
#
T
TAPE
AND
REEL
LSOP-5
10.2 mm
UL, cUL, CQC
UL, cUL, CQC, VDE
VOL3120T
VOL3120-X001T
Document Number: 82656
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VOL3120
www.vishay.com
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
CONDITIONS
SYMBOL
VALUE
UNIT
IF
25
mA
IF(TRAN)
1
A
VR
5
V
Output power dissipation
Pdiss
40
mW
LED junction temperature
Tj
125
°C
IOH(PEAK)
2.5
A
INPUT
Input forward current
Peak transient input current
< 1 μs pulse width, 300 pps
Reverse input voltage
OUTPUT
High peak output current (1)
Low peak output
current (1)
IOL(PEAK)
2.5
A
Supply voltage
(VCC - VEE)
0 to 35
V
Output voltage
VO(PEAK)
0 to VCC
V
Pdiss
220
mW
Tj
125
°C
Storage temperature range
Tstg
-55 to +150
°C
Ambient operating temperature range
Tamb
-40 to +100
°C
Ptot
260
mW
Tsld
260
°C
Output power dissipation
Output junction temperature
OPTOCOUPLER
Total power dissipation
Lead solder temperature
For 10 s, 1.6 mm below seating plane
PSO -Safety Power Dissipation (mW)
Notes
• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
(1) Maximum pulse width = 10 μs, maximum duty cycle = 0.2 %. This value is intended to allow for component tolerances for designs with
IO peak minimum = 2.5 A. See applications section for additional details on limiting IOH peak.
300
Isi - Safety Input Current (mA)
1000
800
600
400
200
250
200
150
100
50
0
0
-40
0
40
80
120
160
200
Tamb - Ambient Temperature (°C)
Fig. 1 - Safety Power Dissipation vs. Ambient Temperature
Rev. 1.5, 08-Jan-16
-40 -10
20
50
80
110 140 170 200
Tamb - Ambient Temperature (°C)
Fig. 2 - Safety Input Current vs. Ambient Temperature
Document Number: 82656
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VOL3120
www.vishay.com
Vishay Semiconductors
RECOMMENDED OPERATING CONDITIONS
PARAMETER
SYMBOL
MIN.
MAX.
UNIT
Power supply voltage
VCC - VEE
15
32
V
mA
Input LED current (on)
Input voltage (off)
Ptot - Total Power Dissipation (mW)
Operating temperature
IF
10
-
VF(OFF)
-3
0.8
V
Tamb
-40
+100
°C
300
Coupled device
250
Detector
200
150
100
Emitter
50
0
-40
0
40
80
120
Tamb - Ambient Temperature (°C)
Fig. 3 - Power Dissipation vs. Ambient Temperature
ELECTRICAL CHARACTERISTICS
PARAMETER
High level output current
Low level output current
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
VO = (VCC - 4 V)
IOH
0.5
-
-
A
VO = (VCC - 15 V)
IOH
2.5
-
-
A
VO = (VEE + 2.5 V)
IOL
0.5
-
-
A
VO = (VEE + 15 V)
IOL
2.5
-
-
A
V
High level output voltage
IO = -100 mA
VOH
VCC - 4
-
-
Low level output voltage
IO = 100 mA
VOL
-
0.2
0.5
V
High level supply current
Output open, IF = 10 mA to 16 mA
ICCH
-
-
2.5
mA
Low level supply current
Output open, VF = -3 V to +0.8 V
ICCL
-
-
2.5
mA
IO = 0 mA, VO > 5 V
IFLH
-
3.4
8
mA
V
Threshold input current low to high
Threshold input voltage high to low
VFHL
0.8
-
-
Input forward voltage
IF = 10 mA
VF
1
1.36
1.6
V
Temperature coefficient of forward voltage
IF = 10 mA
ΔVF/ΔTamb
-
-1.4
-
mV/°C
IR = 10 μA
VBR
5
-
-
V
Input capacitance
Input reverse breakdown voltage
f = 1 MHz, VF = 0 V
CIN
-
45
-
pF
UVLO threshold
VO ≥ 5 V, IF = 10 mA
VUVLO+
11
-
13.5
V
VUVLO-
9.5
-
12
V
UVLOHYS
-
1.6
-
V
CIO
-
0.9
-
pF
UVLO hysteresis
Capacitance (Input to Output)
f = 1 MHz, VF = 0 V
Note
• Minimum and maximum values were tested over recommended operating conditions (Tamb = -40 °C to +100 °C, IF(ON) = 10 mA to 16 mA,
VF(OFF) = -3 V to 0.8 V, VCC = 15 V to 32 V, VEE = ground) unless otherwise specified. Typical values are characteristics of the device and are
the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. All typical values
were measured at Tamb = 25 °C and with VCC - VEE = 32 V.
Rev. 1.5, 08-Jan-16
Document Number: 82656
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VOL3120
www.vishay.com
Vishay Semiconductors
SWITCHING CHARACTERISTICS
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
Propagation delay time to logic low output Rg = 10 Ω, Cg = 10 nF, f = 10 kHz, duty cycle = 50 %
TEST CONDITION
tPHL
0.1
0.25
0.5
μs
Propagation delay time to logic high output Rg = 10 Ω, Cg = 10 nF, f = 10 kHz, duty cycle = 50 %
tPLH
0.1
0.25
0.5
μs
Pulse width distortion
Rg = 10 Ω, Cg = 10 nF, f = 10 kHz, duty cycle = 50 %
PWD
-
-
0.3
μs
Rise time
Rg = 10 Ω, Cg = 10 nF, f = 10 kHz, duty cycle = 50 %
tr
-
0.1
-
μs
Fall time
Rg = 10 Ω, Cg = 10 nF, f = 10 kHz, duty cycle = 50 %
tf
-
0.1
-
μs
UVLO turn on delay
VO > 5 V, IF = 10 mA
TUVLO-ON
-
0.8
-
μs
UVLO turn off delay
VO < 5 V, IF = 10 mA
TUVLO-OFF
-
0.6
-
μs
Note
• Minimum and maximum values were tested over recommended operating conditions (Tamb = -40 °C to +100 °C, IF(ON) = 10 mA to 16 mA,
VF(OFF) = -3 V to 0.8 V, VCC = 15 V to 32 V, VEE = ground) unless otherwise specified. Typical values are characteristics of the device and are
the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. All typical values
were measured at Tamb = 25 °C and with VCC - VEE = 32 V.
IF = 10 mA
to 16 mA
1
500 Ω
5
IF
0.1 μF
90 %
50 %
10 Ω
2
tf
tr
VO
4
10 kHz
50 %
duty cycle
VCC = 15 V
to 32 V
10 nF
3
10 %
OUT
tPHL
tPLH
Fig. 4 - tPLH, tPHL, tr and tf Test Circuit and Waveforms
COMMON MODE TRANSIENT IMMUNITY
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
Common mode transient immunity at
logic high output
Tamb = 25 °C, IF = 10 mA to 16 mA,
VCM = 1500 V, VCC = 32 V
|CMH|
48
-
-
kV/μs
Common mode transient immunity at
logic low output
Tamb = 25 °C, VCM = 1500 V,
VCC = 32 V, VF = 0 V
|CML|
48
-
-
kV/μs
Note
• Minimum and maximum values were tested over recommended operating conditions (Tamb = -40 °C to +100 °C, IF(ON) = 10 mA to 16 mA,
VF(OFF) = -3 V to 0.8 V, VCC = 15 V to 32 V, VEE = ground) unless otherwise specified. Typical values are characteristics of the device and are
the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. All typical values
were measured at Tamb = 25 °C and with VCC - VEE = 32 V.
IF
A
R
B
1
VCM
5
0.1 μF
5V
4
VO
V
dV
= CM
Δt
dt
VCC = 32 V
0V
Δt
VO
2
3
VOH
Switch at A: IF = 10 mA
O
VOL
Switch at B: IF = 0 mA
VCM = 1500 V
Fig. 5 - CMR Test Circuit and Waveforms
Rev. 1.5, 08-Jan-16
Document Number: 82656
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VOL3120
www.vishay.com
Vishay Semiconductors
SAFETY AND INSULATION RATINGS
PARAMETER
TEST CONDITION
Climatic classification
SYMBOL
According to IEC 68 part 1
Comparative tracking index
Maximum rated withstanding isolation voltage
VALUE
UNIT
40 / 100 / 21
t = 1 min
Maximum transient isolation voltage
Maximum repetitive peak isolation voltage
CTI
175
VISO
5300
VRMS
VIOTM
8000
V
VIORM
1050
V
Tamb = 25 °C, VDC = 500 V
RIO
≥ 1012
Ω
Tamb = 100 °C, VDC = 500 V
RIO
≥ 1011
Ω
Output safety power
PSO
900
mW
Input safety current
ISI
250
mA
Safety temperature
TS
Isolation resistance
175
°C
Creepage distance
≥8
mm
Clearance distance
≥8
mm
DTI
≥ 0.4
mm
Input to output test voltage, method B
VIORM x 1.875 = VPR, 100 % production test
with tM = 1 s, partial discharge < 5 pC
VPR
1969
Vpeak
Input to output test voltage, method A
VIORM x 1.6 = VPR, 100 % production test
with tM = 10 s, partial discharge < 5 pC
VPR
1680
Vpeak
Insulation thickness
Environment (pollution degree in accordance to DIN VDE 0109)
2
Note
• As per IEC 60747-5-5, § 7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with
the safety ratings shall be ensured by means of protective circuits.
IF - Forward Current (mA)
100
10
1
1.0
1.2
1.4
1.6
1.8
VF - Forward Voltage (V)
Fig. 6 - Forward Current vs. Forward Voltage
Rev. 1.5, 08-Jan-16
(VOH - VCC) - High Level Voltage Drop (V)
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
0.0
VCC = 15 V to 32 V
IF = 7 mA to 16 mA
IOUT = -100 mA
-0.5
-1.0
-1.5
-2.0
-2.5
-3.0
-40
-20
0
20
40
60
80
100
Tamb - Ambient Temperature (°C)
Fig. 7 - High Level Voltage Drop vs. Ambient Temperature
Document Number: 82656
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VOL3120
www.vishay.com
Vishay Semiconductors
VOL - Low Level Output Voltage (V)
IOH - High Level Output Current (A)
3.0
VCC = 15 V to 32 V
VOUT = VCC - 4 V
IF = 16 mA
2.5
2.0
1.5
1.0
-40
-20
0
20
40
60
80
4.0
VF(OFF) = -3.0 V to 0.8 V
3.0
25 °C
2.5
-40 °C
2.0
1.5
1.0
0.5
0.0
100
0.0
VCC = 15 V to 32 V
IOL = 100 mA
VF(OFF) = -3.0 V to 0.8 V
0.4
0.3
0.2
0.1
-40
-20
0
20
40
60
80
100
Tamb - Ambient Temperature (°C)
1.5
2.0
2.5
-1
100 °C
25 °C
-2
-3
-40 °C
-4
VCC = 15 V to 32 V
IF = 7 mA to 16 mA
-5
-6
0.0
0.5
1.0
1.5
2.0
2.5
IOH - High Level Output Current (A)
Fig. 12 - High Level Voltage Drop vs. High Level Output Current
2.0
3.0
VCC = 15 V to 32 V
VOUT = 2.5 V
VF(OFF) = -3 V to 0.8 V
2.5
VCC = 32 V
IF =10 mA for ICCH
IF = 0 mA for ICCL
1.8
ICC - Supply Current (mA)
IOL - Low Level Output Current (A)
Fig. 9 - Low Level Output Voltage vs. Ambient Temperature
1.0
Fig. 11 - Low Level Output Voltage vs. Low Level Output Current
(VOH - VCC) - High Level Voltage Drop (V)
VOL - Low Level Output Voltage (V)
0.5
0.5
IOL - Low Level Output Current (A)
Tamb - Ambient Temperature (°C)
Fig. 8 - High Level Output Current vs. Ambient Temperature
100 °C
VCC = 15 V to 30 V
3.5
2.0
1.5
1.0
1.6
1.4
ICCH
1.2
1.0
ICCL
0.8
0.6
-40
-20
0
20
40
60
80
100
Tamb - Ambient Temperature (°C)
Fig. 10 - Low Level Output Current vs. Ambient Temperature
Rev. 1.5, 08-Jan-16
-40
-20
0
20
40
60
80
100
Tamb - Ambient Temperature (°C)
Fig. 13 - Supply Current vs. Ambient Temperature
Document Number: 82656
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VOL3120
www.vishay.com
Vishay Semiconductors
tPHL, tPLH - Propagation Delay (ns)
ICC - Supply Current (mA)
2.5
IF = 10 mA for ICCH
IF = 0 mA for ICCL
2.0
ICCH
1.5
1.0
ICCL
0.5
15
20
25
500
IF = 10 mA
Rg = 10 Ω, Cg = 10 nF
f = 10 kHz, duty cycle = 50 %
400
300
tPHL
200
tPLH
100
30
15
Fig. 14 - Supply Current vs. Supply Voltage
4
IFLH
3
IFHL
2
1
0
-20
0
20
40
60
80
VCC = 32 V
IF = 10 mA
Rg = 10 Ω, Cg = 10 nF
f = 10 kHz, duty cycle = 50 %
400
300
tPHL
200
tPLH
100
100
-40
-20
0
20
40
60
80
100
Tamb - Ambient Temperature (°C)
Tamb - Ambient Temperature (°C)
Fig. 15 - Threshold Current vs. Ambient Temperature
Fig. 18 - Propagation Delay vs. Ambient Temperature
500
tPHL, tPLH - Propagation Delay (ns)
30
VO - Output Voltage (V)
30
500
VCC = 15 V to 32 V
-40
25
Fig. 17 - Propagation Delay vs. Supply Voltage
tPHL, tPLH - Propagation Delay (ns)
IFHL, IFLH - Threshold Current (mA)
5
20
VCC - Supply Voltage (V)
VCC - Supply Voltage (V)
25
20
15
10
5
0
0
1
2
3
4
5
IF - Forward Current (mA)
Fig. 16 - Output Voltage vs. Forward Current
Rev. 1.5, 08-Jan-16
400
VCC = 32 V
Rg = 10 Ω, Cg = 10 nF
f = 10 kHz, duty cycle = 50 %
300
tPHL
200
tPLH
100
5.0
7.5
10.0
12.5
15.0
IF - Forward Current (mA)
Fig. 19 - Propagation Delay vs. Forward Current
Document Number: 82656
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VOL3120
Vishay Semiconductors
500
tPHL, tPLH - Propagation Delay (ns)
tPHL, tPLH - Propagation Delay (ns)
www.vishay.com
IF = 9 mA
VCC = 15 V
Cg = 10 nF
f = 10 kHz, duty cycle = 50 %
400
tPHL
300
200
tPLH
100
0
10
20
30
40
500
IF = 9 mA
VCC = 32 V
Rg = 10 Ω
f = 10 kHz, duty cycle = 50 %
400
300
tPHL
200
tPLH
100
0
50
Rg - Load Resistance (Ω)
20
40
60
80
100
Cg - Load Capacitance (nF)
Fig. 20 - Propagation Delay vs. Load Resistance
Fig. 21 - Propagation Delay vs. Load Capacitance
+ 0.30
- 0.40
10.20
3.80 typ.
7.50 ± 0.20
0.20
+ 0.10
- 0.05
0.10 ± 0.10
4.10 max.
2.50
2.80 max.
PACKAGE DIMENSIONS (in millimeters)
3
0.45 ± 0.1
0.70
2.54 nom.
+ 0.30
- 0.40
Leads coplanarity 0.10 max.
1.27 nom.
Possible footprint
4
3
3
0.90
2.54
5
8.20
10.80
1
2
Pin no. 1 identification
Fig. 22 - Package Drawing
Rev. 1.5, 08-Jan-16
Document Number: 82656
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
VOL3120
www.vishay.com
Vishay Semiconductors
PACKAGE MARKING
3120
3120X1
V YWW 68
V YWW 68
Fig. 23 - VOL3120T
Fig. 24 - VOL3120-X001T
PACKING INFORMATION (tape and reel)
Top cover tape
Embossed carrier
Embossment
17998
Fig. 25 - Tape and Reel Shipping Medium
2.00 ± 0.10
4.00 ± 0.10
1.55 ± 0.05
1.75 ± 0.10
0.30 ± 0.05
7.50 ± 0.10
Y
1.50
8.00 ± 0.10
+ 0.20
0.00
4.30 ± 0.10
16.00 ± 0.30
Y
CL
2.75 ± 0.10
3.20 ± 0.10
Note:
1. Cumulative tolerance of 10 spocket holes is ± 0.20.
Fig. 26 - Tape and Reel Packing (2000 pieces on reel)
SOLDER PROFILE
HANDLING AND STORAGE CONDITIONS
ESD level: HBM class 2
300
max. 260 °C
245 °C
255 °C
240 °C
217 °C
250
Temperature (°C)
Section Y - Y
Floor life: unlimited
Conditions: Tamb < 30 °C, RH < 85 %
Moisture sensitivity level 1, according to J-STD-020
200
max. 30 s
150
max. 100 s
max. 120 s
100
max. ramp down 6 °C/s
50
max. ramp up 3 °C/s
0
0
19841
50
100
150
200
250
300
Time (s)
Fig. 27 - Lead (Pb)-free Reflow Solder Profile
According to J-STD-020
Rev. 1.5, 08-Jan-16
Document Number: 82656
9
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000