EL7182 ® Data Sheet January 1996, Rev. B FN7281 2-Phase, High Speed CCD Driver Features The EL7182 is extremely well suited for driving CCD's, especially where high contrast imaging is desirable. The 16V supply rating is attractive for higher voltage CCD applications, as in color fax machines. The input is TTL and 3V compatible. The low quiescent current requirement is advantageous in portable/battery powered systems. The EL7182 is available in 8-pin PDIP and 8-lead SO packages. • 3V and 5V Input compatible Pinout • Wide operating voltage—4.5V–16V EL7182 (8-PIN PDIP, SO) TOP VIEW • Clocking speeds up to 10MHz • Reduced clock skew • 20ns Switching/delay time • 2A Peak drive • Low quiescent current Applications • CCD Drivers requiring high-contrast imaging • Differential line drivers • Push-pull circuits Ordering Information PART NUMBER Manufactured under U.S. Patent Nos. 5,334,883, #5,341,047 1 TEMP. RANGE PACKAGE PKG. NO. EL7182CN -40°C to +85°C 8-Pin PDIP MDP0031 EL7182CS -40°C to +85°C 8-Pin SO MDP0027 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners. EL7182 Absolute Maximum Ratings (TA = 25°C) Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125°C Power Dissipation SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .570mW PDIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1050mW Supply (V+ to Gnd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V above V+ Combined Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . .4A Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER TA = 25°C, V = 15V unless otherwise specified DESCRIPTION TEST CONDITIONS MIN TYP MAX UNITS INPUT VIH Logic “1” Input Voltage IIH Logic “1” Input Current VIL Logic “0” Input Voltage IIL Logic “0” Input Current VHVS Input Hysteresis 2.4 @V+ V 0.1 @0V 0.1 10 µA 0.8 V 10 µA 0.3 V OUTPUT ROH Pull-Up Resistance IOUT = -100mA 3 6 Ω ROL Pull-Down Resistance IOUT = +100mA 4 6 Ω IPK Peak Output Current Source Sink 2 2 IDC Continuous Output Current Source/Sink IS Power Supply Current Input High VS Operating Voltage A 100 mA POWER SUPPLY AC Electrical Specifications PARAMETER 2.5 4.5 5 mA 16 V TA = 25°C, V = 15V unless otherwise specified DESCRIPTION TEST CONDITIONS MIN TYP MAX CL = 500pF CL = 1000pF 7.5 10 20 CL = 500pF CL = 1000pF 10 13 20 UNITS SWITCHING CHARACTERISTICS tR tF Rise Time Fall Time ns ns tD-ON Turn-On Delay Time 18 25 ns tD-OFF Turn-Off Delay Time 20 25 ns 2 EL7182 Timing Table Standard Test Configuration Simplified Schematic 3 EL7182 Typical Performance Curves Switch Threshold vs Supply Voltage Max Power/Derating Curves Input Current vs Voltage Peak Drive vs Supply Voltage Quiescent Supply Current “ON” Resistance vs Supply Voltage CASE: Average Supply Current vs Voltage and Frequency 4 INPUT LEVEL CURVE GND B V+ D Average Supply Current vs Capacitive Load EL7182 Typical Performance Curves (Continued) Rise/Fall Time vs Load Rise/Fall Time vs Supply Voltage Rise/Fall Time vs Temperature Propagation Delay vs Supply Delay Time vs Temperature All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 5