CC7, CCB www.vishay.com Vishay Electro-Films Thin Film Resistor Divider Network on Alumina, User Trimmable FEATURES • Wire bondable • Small single chip size CC7 - 0.030" x 0.030" CCB - 0.050" x 0.050" • Case: 0303, 0505 • Alumina substrate • Low stray capacitance: < 0.2 pF • Resistance range RT: 100 to 20 k for CC7 100 to 50 k for CCB • Resistor material: Nichrome • User trimmable • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 Product may not be to scale The CC7 and CCB series resistor chips offer the combination of user trimmability, low shunt capacitance and excellent stability. The CC7 and CCB can be specified as either a single RT value resistor, as two resistors with a center tap feature (1:1 ratio or custom) ratio or user trimmable. APPLICATIONS The CC7 and CCBs a six bonding pads allows the user increased layout flexibility. The CC7 and CCBs are manufactured using Vishay Electro-Films (EFI) sophisticated thin film equipment and manufacturing technology. They are 100 % electrically tested and visually inspected to MIL-STD-883, method 2032 class H or class K. Vishay EFI CC7 and CCB chip resistors provide excellent high frequency response and are ideally suited for prototyping. Typical application areas are: • Amplifiers • Oscillators • Attenuators • Couplers • Filters Recommended for hermetic environments where die is not exposed to moisture TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES PARAMETER Total Resistance Range Standard Tolerances TCR VALUE 100 to 50K ± 0.1 ± 10, ± 25, ± 50, ± 100 UNIT % ppm/°C Tightest Standard Tolerance Available 0.1 % ± 10 ppm/°C ± 25 ppm/°C ± 50 ppm/°C ± 100 ppm/°C 100 Ω 200 Ω 1 kΩ 50 kΩ STANDARD ELECTRICAL SPECIFICATIONS PARAMETER Noise, MIL-STD-202, Method 308 Stability, 1000 h, + 125 °C at Rated Power Operating Temperature Range Thermal Shock, MIL-STD-202, Method 107, Test Condition F High Temperature Exposure, + 150 °C, 100 h Dielectric Voltage Breakdown Insulation Resistance Operating Voltage DC Power Rating at 125 °C 5 x Rated Power Short-Time Overload, + 25 °C, 5 s VALUE - 20 typ. + 0.1 max. R/R - 55 to + 125 + 0.25 max. R/R + 0.25 max. R/R 400 1012 min. 100 max. 0.1 max. (50 mil) 0.05 max. (30 mil) + 0.25 max. R/R UNIT dB % °C % % V V W % Note • Performance characteristics are not guaranteed once user trimmed Revision: 18-Apr-13 Document Number: 61012 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CC7, CCB www.vishay.com Vishay Electro-Films DIMENSIONS in inches CC7 0.005 CCB 0.030 0.050 0.0075 0.005 0.005 0.030 0.016 0.050 0.035 0.005 0.005 SCHEMATIC RT = RA + RB RA RB MECHANICAL SPECIFICATIONS PARAMETER VALUE 0.030" x 0.030" ± 0.003" (0.76 mm x 0.76 mm ± 0.08 mm) 0.050" x 0.050" ± 0.003" (1.27 mm x 1.27 mm ± 0.08 mm) Chip Size Chip Thickness 0.010" ± 0.002" (0.25 mm ± 0.03 mm) Chip Substrate Material 99.6 % alumina, 2 microinch to 4 microinch finish Resistor Material Nichrome Bonding Pad Size 0.005" x 0.005" (0.12 mm x 0.12 mm) min. Number of Pads 6 Pad Material 25 kÅ minimum gold standard Backing None GLOBAL PART NUMBER INFORMATION Global Part Number: CC750000KCKKGNHWS Global Part Number Description: CC7 5K 10 % RT 0.25 % 100 ppm/°C 10 ppm/°C Au None H WS C MODEL CC7 = 30 x 30 size CCB = 50 x 50 size C 7 5 0 RESISTANCE RESISTANCE MULTILPLIER (R TOTAL) CODE First 4 digits are significant figures of resistance Revision: 18-Apr-13 B = 0.01 A = 0.1 0=1 1 = 10 0 TOL. CODE (%) 0 0 RATIO TOL. (%) K TCR (ppm/°C) E = ± 25 B = 0.1 B = 0.1 C = 0.25 C = 0.25 C = ± 50 D = 0.5 D = 0.5 K = ± 100 F = 1.0 M = ± 250 F = 1.0 G = 2.0 G = 2.0 J = 5.0 U = User N = No K = 10 C K TC TRACK (ppm/°C) G=±2 J=±5 K = ± 10 N = No K G TERMINATION G = Au A = Al N H W S BACK VISUAL PACKAGING METAL CLASS CODE G= Au N= None H= Class H K= Class K WS = Waffle pack 100 min., 1 mult Document Number: 61012 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000