BRCP www.vishay.com Vishay Electro-Films Thin Film Bar MOS Capacitors FEATURES • Robust MOS construction • Allows for multiple wire bonds. At the lowest values, case A will accept 7 bonds and case B will accept 15. • Low D, high Q • Excellent load life stability APPLICATIONS Product may not be to scale The bar capacitor is a MOS capacitor designed for hybrid assemblies requiring ultra high power rating with miniature case size. • Hybrid assemblies • Low pass LC, RC, or LRC lumped filter • RF blocking on DC feeds • Impedance matching • SiC or GaN high frequency / high power applications WV (DC) VALUES AND TOLERANCES CAPACITOR MODEL Case Size Capacitance Values Tolerance DC Working Voltage A B 1204 2404 UNIT 5 to 50 10 to 100 pF 5 5 % 100 100 V STANDARD ELECTRICAL SPECIFICATIONS PARAMETER Capacitance Range VALUE UNIT 5 to 100 pF Down to ± 5 % Absolute TCC, -55 ° to 125 °C ± 50 ppm/°C Operating Temperature Range Absolute Tolerance, 1 kHz (1) -55 to +150 °C Operating Voltage 100 max. V Dissipation Factor, 1 MHz 0.01 max. Absolute Value Stability, 1 kHz, 1000 h, 70 °C, 100 VDC ± 0.25 % Short Time Overload, 2 x Rated Voltage, 25 °C, 5 s ± 0.25 % Thermal Shock, MIL-STD-202, Method 107 F ± 0.25 % Moisture Resistance, MIL-STD-202, Method 106* ± 0.25 % High Temperature Exposure, 100 h, 150 °C ± 0.25 % Low Temperature Operation, -65 °C, 45 min, 100 VDC ± 0.25 % Note (1) See table “Case Size Value and Tolerance”. Revision: 22-Jan-15 Document Number: 61106 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 BRCP www.vishay.com Vishay Electro-Films MECHANICAL SPECIFICATIONS PARAMETER VALUE Chip Substrate Material Silicon Dielectric Silicon dioxide Top Termination Au 1 μm min. Case Size See table “Case Size Value and Tolerance” Passivation None Number of Pads 1 Back Termination (Epoxy only) TiW/Au CASE SIZE VALUE AND TOLERANCE MAX. OPERATING VOLTAGE (V) NOMINAL VALUE (pF) CASE TYPE A CASE TYPE B BEST TOLERANCE (± %) 5 + - 10 100 7.5 + - 7 100 10 + + 5 100 12.5 + + 5 100 15 + + 5 100 17.5 + - 5 100 20 + + 5 100 22.5 + - 5 100 25 + + 5 100 27.5 + - 5 100 30 + + 5 100 32.5 + - 5 100 35 + + 5 100 37.5 + - 5 100 40 + + 5 100 42.5 + - 5 100 45 + + 5 100 47.5 + - 5 100 50 + + 5 100 55 - + 5 100 60 - + 5 100 65 - + 5 100 70 - + 5 100 75 - + 5 100 80 - + 5 100 85 - + 5 100 90 - + 5 100 95 - + 5 100 100 - + 5 100 Revision: 22-Jan-15 Document Number: 61106 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 BRCP www.vishay.com Vishay Electro-Films CASE SIZE A 0.12" x 0.035" A E C B 5 pF D 6.5 pF 10 pF 7.5 pF G F I K J H 17.5 pF 20 pF 22.5 pF L 25 pF 27.5 pF O M 35 pF 37.5 pF 30 pF R P N 32.5 pF 15 pF 12.5 pF S 40 pF 42.5 pF 45 pF T U 47.5 pF Revision: 22-Jan-15 50 pF Document Number: 61106 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 BRCP www.vishay.com Vishay Electro-Films CASE SIZE B 0.24" x 0.035" A C B 10 pF E D 13 pF 15 pF G F 20 pF 25 pF I H 35 pF K J 40 pF 45 pF M L 50 pF 55 pF O N 65 pF 30 pF R P 70 pF 75 pF 60 pF S 80 pF 85 pF 90 pF T U 95 pF Revision: 22-Jan-15 100 pF Document Number: 61106 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 BRCP www.vishay.com Vishay Electro-Films GLOBAL PART NUMBER INFORMATION Global Part Number: BRCPA1000BKGCST Global Part Number Description: BRCP 3 mm 10 pF 10 % Au C ST B R MODEL SIZE BRCP A= 3 mm x 1 mm B= 6 mm x 1 mm Bar Capacitor Revision: 22-Jan-15 C P CAPACITANCE (pF) First 4 digits are significant figures of capacitance A 1 0 CAPACITANCE MULTIPLIER CODE C = 0.001 B = 0.01 A = 0.1 0 0 TOLERANCE CODE J=5% K = 10 % M = 20 % L = 25 % B K TERMINATION G = Au A = Al G C S T VISUAL CLASS PACKAGING CODE C= Commerical E= Electrical test only H= Class H K= Class K WS = Waffle pack 100 min., 1 mult FW = Full wafer HW = Half wafer ST = Diced on tape Document Number: 61106 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000